Search Documents

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

Executive Committee, Board of Directors Augustus B Kinzel, Chairman, J L Glllson, Vice-Chairman, A W Thornton, Howard C Pyle, Grover J Holt Finance Committee, Board of Directors Andrew Fletcher, Chairman, J S Vanick, Gall F Moulton Investments Gail F Moulton, '60, Chairman, Henry Krumb, '59, J Loveloy, '61, C R Dodson, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Com¬mittee Endowment Andrew Fletcher, Chairman, N G Alford, H DeWitt Smith, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, O H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships H DeWitt Smith, '59, Chairman, C E Reistle, Jr, '59, Grover J Holt, '59, L F Reinartz, '59, M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, Augustus B Kinzel, ex off as President

Jan 1, 1958

By A. G. Suydam

Ancient as is the art of producing copper, so ancient is one of its eternal problems: refractories. Looking backward, in the light of present knowledge, clouded though it be, one cannot avoid a sense of profound respect for the patience, acumen and courage of those who have wrought so successfully despite difficulties, a more accurate understanding of which seems merely to accentuate. The problem of refractories arises from the necessity for constructing containers in which to bring natural ores into thermal solution in order to effect reduction and separation of the valuable metal content and free it of undesirable contamination while producing a waste slag. The very forces known to produce thermal solution of sufficient liquidity are necessarily destructive of exposed refractory linings in proportions varying inversely with thermal conductivity, directly with the porosity and ease of fluxing of the refractories used, and directly with the temperatures employed. Beyond this, mechanical forces are set up within the refractory lining incident to rapid heating or cooling, shrinkage at high temperatures, and unequal or excessive loading, that frequently pass the elastic limit, causing spalling or distortion. The effects of these forces are often accentuated by the necessity of providing at the same time as hot a bath and as cool a container as are consistent with fuel economy. Evolution in the Use of Refractories Clay Brick.—Fireclay and clay refractories had to yield wherever they were in contact with slags rich in basic oxides, first because of the combining power of those oxides with free silica and secondly because of the tendency of alumina to form either aluminates or alumina-silicates of varying complexity. Of no less importance, the incipient fusion point was low as compared with good clay brick of today, while the brick lacked strength at high temperatures. Expansion was slight, therefore it was difficult to make and maintain tight walls, roof, or bottom. However, the spalling tendency was low because of some of these properties and clay brick have retained their place in roasting furnaces, boiler furnace linings, and in the upper walls of some of the reverberatory types such as some refining, anode and wire-bar furnaces. They have served often and most efficiently for hot patching.

Jan 1, 1934

The first mention of the occurrence of native copper near Lake Superior is found in a book by Lagarde, published in 1636. The letters of the Jesuit missionaries in the seventeenth century refer to the use of this copper by the Indians. Francesco Bressani, an Italian friar, says, in 1653: "There is a copper ore, which is very pure, and which has no need of passing through the fire; but it is in places far distant and hard to reach. We have seen it in the hands of the barbarians".* Father Jerome Lalemant, writing in 1659, says that the coast of Lake Superior is "enriched with copper of such excellence that pieces as large as one's fist are found, all refined.† These pieces of copper were hoarded by the Indians as mascots. The mention of the metal as having been already refined by nature recalls the fact that the old Greek historians spoke of gold-dust as being apuron, or not needing the fire. Father Claude Allouez,‡ writing in 1666, says: "One often finds at the bottom of the water [of Lake Superior] pieces of pure copper, of ten and twenty livres [pounds] weight. I have several times seen such pieces in the savages' hands; and since they are superstitious [as if the padres themselves were not!], they- keep them as so many divinities, or as presents which the gods dwelling beneath the water have given them, and on which their welfare is to depend. For this reason they preserve these pieces of copper, wrapped up, among their most precious possessions".

Jan 1, 1932

By Donald R. Reichmuth

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks."1 There are now three distinct approaches being used to determine the tensile strength of brittle materials. These are shown schematically in Fig. 1. The first method consists of simply pulling the specimen apart by applying an axial load. Although this procedure is the easiest to understand, the technical problems encountered during testing are numerous. Specimens cannot be readily fabricated into dumbbell-shaped specimen* like those customarily used for testing inetals. Cylindrical specimens cannot be loaded in jaw-clamps because adverse stress conditions arise at the clamping points, which causes unreliable results. An innovation developed by Niles Grosvenor at the Colorado School of Mines, in which the load is applied through steel-end caps glued to the ends of the specimens, has considerable merit, hut the samples are costly to prepare.2 All tests using a direct pull are further handicapped by the possibility of small amounts of bending being present, the specimen's surface condition, and

Jan 1, 1968

By D. P. Morton

SINCE 1023, which closed the speculative era in the bituminous coal fields of the United States, there have been wide annual fluctuations in the national production of bituminous coal. These changes in annual output have been variously attributed to: (I) increased competition from petroleum products, natural gas and hydroelectric power; (2) lower unit consumption of coal; and (3) fluctuations in the general business level. The purpose of this paper is to measure, from a practical standpoint, the net effect upon the annual trend of bituminous coal production, and to give those who are interested a basis for estimating in advance the probable output of bituminous coal. It can readily be shown that changes in the level of general business affect the national production of bituminous coal more than does any other factor. Therefore it is necessary to use some standard measure of the relative business level for purposes of comparison. The Federal Reserve Board Index of Industrial Production offers the basis for such a measure.' This Index, a weighted composite of 81 different series, rests upon the averages of the years 1935 to 1939 as loo, and is presented graphically in Fig. I. Even a cursory examination of the chart will indicate a definite uptrend for industrial production over a period of years. This uptrend is due to at least two factors: (I) an actual increase in national population, and (2) a probable increase in the per capita consumption of goods. This means that there is no such thing as a fixed Normal, rather Normal is a variable, tending to increase from year to year. In order to measure the amount of annual increase in normal, the Index of Industrial Production must be studied in relation to its major components, Durable Goods and Nondurable Goods. Durable Goods are those made from the lasting materials such as iron, steel, other metals, lumber, stone, cement, clay, glass. Nondurable Goods are those for early consumption, such as foods, textiles, tobacco, chemicals, paper, gasoline, and goods made of leather and rubber. The purchase of Durable Goods may be postponed, but Nondurable Goods must be purchased currently unless the standard of living is lowered. The Federal Reserve Indexes of durable and nondurable goods are shown graphically, 1920 to 1939, on Fig. 2 (pp. 764-765 of ref. I). It is apparent that fluctuations in the production of nondurable goods are not nearly so wide as in the production of durable goods, and that the curve of Industrial Production (Fig. I) would fall between the two curves on Fig. 2. It would, however, seem logical that both curves should follow the same long-term trend, or that over a period of two to three decades the relative proportion of durable and nondurable goods, in periods of normal production, should he the same. It is neces-

Jan 1, 1941

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

By S. L. Craig, C. Orr, H. G. Blocker

WITHIN recent years gas adsorption methods have been developed for measuring the surface area of finely divided materials and have become extremely valuable in research on the corrosion and the catalytic activity of metals. Rather elaborate apparatus is required, and a single determination is so time-consuming that these methods have not been utilized to the fullest extent; the methods are un-suited for most routine control work such as that encountered in powder metallurgical operations and in processes employing metal catalysts. These difficulties are largely eliminated, and surface area is reduced to a routine determination if the liquid-phase adsorption of a surface-active agent such as a fatty acid can be used. When the affinity of the fatty acid carboxyl group for the solid surface is greater than its affinity for the solvent, a unimolec-ular layer of orientated fatty acid molecules will be formed at the solid-liquid interface in a manner similar to that of a compressed fatty acid film on a water surface. The measurement of surface area is then reduced to a measurement of fatty acid adsorption. This propitious circumstance, first investigated by Harkins and Gans,¹ has been employed with somewhat inconclusive results by a number of investigators in evaluating the surface properties of metals, metal catalysts, and metal oxides. The specific surface area values for nickel and platinum catalysts, determined from the adsorption of a number of fatty acids from various solvents, were found by Smith and Fuzek² to agree with values calculated by the gas adsorption technique of Brunauer, Emmett, and Teller," he so-called BET technique. And recently Orr and Bankston4 have also reported good agreement between nitrogen gas and stearic acid adsorption results in the measurement of the surface areas of clay materials. On the other hand, Ries, Johnson, and Melik5 found only order-of-magnitude agreement between these two methods in studying supported, cobalt catalysts having specific surface areas as great as 420 sq m per g; the reason is partially attributable to the very porous nature of the materials. Greenhill,6 investigating the adsorption of long-chain, polar compounds in organic solvents on a number of metal powders, concluded that a uni-molecular layer of stearic acid was formed on exposure of the solid to the acid solution and that the presence of an oxide or another film did not alter this result. Furthermore, the adsorption process appeared to be the same whether or not the sample was degassed prior to exposure to the solution. Greenhill estimated the surface area of one of the powders he investigated from microscopic diameter measurements, and obtained a rough check with surface area evaluation. Russell and Cochran7 found moderate agreement for alumina surface area results by fatty acid and gas adsorption methods. In addition, they also found that the prolonged heating and evacuating pretreatments previously used by investigators were unnecessary. The present work, however, considerably extends these previous investigations, shows that fatty acid adsorption can be used to determine the surface area of a variety of metals and metal compounds, offers further confirmation of the correctness of gas adsorption methods, and presents a simplified technique for the determination of the metal surface area which is suitable for routine work. Experimental Technique Basically, the fatty acid adsorption method is quite simple. It consists of exposing a sample of the material of which the surface area is desired to a fatty acid solution of known concentration. By analysis of an aliquot of the solution, the concentration after adsorption has occurred may be determined. The difference between the initial quantity of acid in solution and the final quantity is that quantity of acid adsorbed by the sample. The specific surface area of the adsorbent material may be calculated from the quantity adsorbed and the weight of the sample. In agreement with the findings of others as outlined above, it was found entirely unnecessary to degas or pretreat the nonporous materials employed other than by drying them thoroughly. However, precaution was necessary so that the dried sample entered the fatty acid solution with little exposure to moisture. The effect of moisture on the interaction of stearic acid with finely divided materials has been thoroughly investigated by Hirst and Lancaster." They found the presence of water merely reduced the amount of acid adsorbed by powders such as TiO2, SiO2, Tic, and Sic. With reactive materials such as Cu, Cu2O, CuO, Zn, and ZnO, however, water was found to initiate chemical reaction. Only with ZnO was reaction observed when the solid and the solu-

Jan 1, 1953

By H. C. Gatos, A. D. Kurtz

WITH the growing interest in the mechanism of self-diffusion of metals, the study of accurate and convenient methods for determining self-diffu-sion coefficients appears highly desirable. It was with this objective in mind that the present investigation was undertaken. Gatos and Azzam1 employed an autoradiographic technique for measuring self-diffusion coefficients of gold. This method involved sectioning of the specimen through the diffusion zone and recording the radioactivity directly on a photographic film. Because of the very short range of the emitted ß rays in gold, the activity recorded on the film was essentially the true surface activity. With proper choice of the sectioning angle, sufficient resolution could be obtained and the entire concentration-distance curve recorded in one measurement. For the boundary conditions of the experiment, where an infinitesimally thin layer of radioactive material diffuses in positive and negative directions into the end faces of a rod of infinite length, the solution of the diffusion equation is C/Cn = 1/v4pDt exp (-x2/4Dt) where C is the concentration of diffusing element (photographic density in this case), C,, is the constant (depending upon amount of radioactive material), x is the diffusion distance, D is the diffusion coefficient, and t is the time. Thus, by plotting the logarithm of the concentration vs the square of the diffusion distance, a straight line results and the slope contains the diffusion coefficient. In this manner, the self-diffusion coefficient of gold can be obtained as a function of temperature. In the present investigation the results reported by Gatos and Azzam1 have been verified, and the autoradiographic technique has been further developed and applied for the determination of the self-diffusion coefficient of gold at a number of temperatures. Furthermore, the energy of activation for the self-diffusion of gold has been conveniently determined. . Experimental Techniques Preparation of Specimens: The inert gold of high purity was received in the form of a rod from which cylinders were cut and machined to a diameter of 0.500 in. The specimens were annealed to a suitably large grain size and the faces were surface ground prior to the deposition of the radioactive layer. The radioactive isotope Au198 was chosen. It was produced in the Brookhaven pile by means of the reaction Au197 + n ? Au108. It decays by ß emission (0.96 mev) to Hg108 with the subsequent emission of a y ray (0.41 mev). 70Au 108 ? 80Hg 108 + -1e°. The half life of the Au108 is 2.7 days so that a strict time schedule had to be maintained in order to secure sufficient activity until the end of the experiments. For this reason, initial activities as high as 10,000 millicuries per gram were used. The gold arrived in the form of foil and was evaporated onto one face of each gold specimen cylinder to a thickness of about 100A. A sandwich-type specimen was formed by welding two such cylinders together. Evaporation of Gold: The gold was evaporated under vacuum from heated tantalum strips which were bent in such a way as to limit the solid angle through which the gold was allowed to vaporize, thus insuring a more efficient utilization of the gold. The specimens rested on flat brass rings which had an inner diameter of 0.475 in. The entire specimen-holding assembly could be manipulated from outside the vacuum system by means of a magnet which attracted a slug of soft iron attached to the assembly. By evaporating inert gold on glass slides under conditions identical to those employed for the radioactive gold, it was found that the thickness of the films was about 100A. Welding: The welding was performed by hot pressing in a stainless steel cylinder. The inside of the cylinder was threaded and fitted for two plugs. The specimens to be welded were placed in the middle of the cylinder and two pressing disks, one at each end, were inserted to avoid shearing stresses as the plugs were tightened. Mica disks were placed between the pressing disks and the specimens to prevent them from welding. The plugs were then tightened with a hand wrench and the entire unit was placed in an argon stream for about an hour to remove the oxygen. The unit was then inserted in the center of an argon atmosphere furnace maintained at about 700°C and left there for about an hour. Because of the difference in the temperature coefficient of expansion of the two metals, as the temperature rose. the pressure on the specimen-rollple increased and a weld resulted Welding was generally satisfactory under the conditions described.

Jan 1, 1955

PRESENTATION of the 1922 Washington Award to Capt. Robert W. Hunt, honorary member and twice president of the Institute, was made at the annual dinner of the Western Society of Engineers, in Chicago, on June 18, 1923, in the presence of 250 mem-bers and guests. W. L. Abbott, Chairman of the Award Commission, when delivering the presentation address, said The life of the Govern-ment of this country, as the lives of governments are usually measured, is short, barely 150 years, but meas-ured by what it has accom-plished, this country has reached a venerable age. The first 75 years of our country's existence were necessarily preparatory to the greater developments which came in the second, and that last half of our country's existence is ex-ceeded, by ten years, by the span of life of our honored guest. "Very little iron and steel were produced in this coun-try until after the birth of Robert W. Hunt. And it was not until after 1860, when as a boy of 21 he joined his fortunes with those of the Cambria Iron Works, that the iron and steel business of the country really took root. After a year or two with the Cambria Works, he left a promising position to go into the army, where he served for four years. After the close of the war he returned to the iron works and qualified himself as a metallurgical chemist.

Jan 7, 1923

By J. W. Gabelman

A study of spatial relations between uranium and other metal deposits and hydro thermally altered rocks in western Colorado demonstrated districtwide and regional zoning. The pattern was later found repeated elsewhere in the Western Hemisphere Cordillera. District mineralization centers are pipelike bodies of pervasively altered rock from which intensity-temperature-pressure gradients decreased outwardly. Uranium occurs in several zonal environments but usually is economic only in outermost zones. The general similarity of zones throughout the tectoni-cally and metallogenically uniform Cordillera may reflect a consistent hydrothermal process involving zoning. By determining positions of zones it should be possible to select for examination the most favorable small portions of districts or provinces. Mineralogical zoning has been discussed by Lindgren,l3 Graton,lo Emmons,' Blanchard,' Park and many others. It is commonly found to some extent in most mineralized areas. The existence of nonmetallic alteration envelopes around lode metal deposits and their relation to metallization were first emphasized by Lovering,l4 Burbank, Sales and Meyer," Sales,2o McKinstry,I7 Lovering and others15 and Schmitt. Also, large areas of nonmetallic alteration containing porphyry-type replacement metal disseminations have long been recognized and are described by Schwartz,25-28 Kerr and others" and Gilully. In some districts, e. g., Bingham Canyon, Utah, and Santa Rita, N.M., base metal lode deposits and their alteration envelopes are zoned around large altered areas which contain porphyry copper replacement disseminations; however, the spatial and genetic relations between lodes and replacement disseminations and their associated alterations do not seem to have received sufficient attention. Bodies of altered rock containing porphyry-type replacement disseminations are many times larger than the alteration envelopes containing lode deposits. The two types are rarely superimposed. They occur adjacent to or independent of one another, but they are believed to be related through the mechanism of zoning as suggested by Gabelman and Boyer. 5'6 Most of the significant lode metal deposits are distributed around central pipelike bodies of strong, pervasive, nonmetallic alteration which may or may

Jan 1, 1962

By J. F. Myers, R. J. Tower

"There is nothing new under the sun." All over the world, mineral-dressing engineers are working at their problems, no two of which are alike. Each encounters equipment and process problems. Many devise simple ways and means of overcoming their difficulties. Many of these problems are quite common in the industry, yet, since no one human being seems capable of thinking of everything, these problems at some plants often are looked upon as necessary evils. The purpose of this symposium is to gather together, from competent engineers, devices and practices that have been useful to them. Most of the ideas contributed are not new, yet there is no plant operator, old timer or youngster, who will not find some idea herein that will give him a suggestion for improving his operation. Space does not permit a complete elaboration on all of the contributions offered. Each item is summarized, but this will be ample for those skilled in the art of mineral dressing. A list of contributors appears at the end of the paper, and the superior number at the end of each item identifies its source. General Equipment A signal light to show that a steel bin, containing relatively line, moist ore, is full, can be made by suspending a copper rod in the bin to a sufficient depth to ensure ample contact with the ore. One wire of a 32-volt circuit should be attached to the rod and one to the side of the bin. Sufficient current will flow to make the signal light burn. A 110-volt circuit could be used, but 32 volts ensures safety.10 Fig I shows a circular bin for crushed ore. It is a concrete structure footed on the ground, using no supporting columns. Tailing from the sink-float was used for aggregate. Cross conveyors for discharging ore are not required, nor is a tripper for filling. Segregation is minimized by drawing from different gates. An exhaust fan on top of the bin eliminates condensation due to temperature of the ore.21 A beam with an adjustable point of suspension near the center permits rigging rolls for removal in a very few minutes. This makes unnecessary the lacing of the cable through the hub bolts on one side, around the shaft on the other, and the trouble of balancing the load.8 The ratchet handle on a Symons crusher may be replaced by a drum with a cable wound on it. When the cable is pulled by a crane or hoist it causes the drum to revolve and thus screws or unscrews the bowl. This reduces handwork and materially shortens the time required for the job.' TO Spread ore feed from an apron feeder over a belt conveyor, place a heavy steel bar about midway between the top

Jan 1, 1949

By Robert T. Chapman

The revolution in equipment for blasthole drilling, ore loading, and ore hauling has been so rapid over the last ten years that it has generated an important new profit potential in the mining industry. With the new high-capacity machinery now available, it is possible for a mining enterprise to earn a profit from larger and lower grade orebodies than ever before despite the ever-increasing burden of rising costs. Just what such equipment can accomplish when coupled with improved mining practice has been demonstrated with startling success at the No. 1 mine of Minerva Oil Co. near Cave-in-Rock in Hardin County, Ill. The No. 1 is an underground operation which has been producing fluorspar and zinc ores and concentrates continuously since 1944. A few years ago, when the mine neared the familiar cross-roads where rising costs, increasing tonnages, and relatively static product prices converge, company officials decided to bolster the operation with new mobile equipment. They chose three machines which proved so effective that output at the No. 1 doubled between 1963 and 1965,while costs dropped by about 40% in the same period.

Jan 11, 1966

By R. H. McLean

Jet impingement produces two mechanisms to clean the bottom of a borehole during jet-bit drilling operations. One is an impact-pressure wave in the immediate area of jet impingement. The other is crossflow, which spreads across the bottom away from the pressure wave. Measurements of the vertical distribution of the cross-flow at several positions beneath a 4 3/4-in. tricone jet bit in a laboratory model show that the maximum velocity in the crossflow is directly proportional to the square root of the product of the rate of flow and the velocity of the jets through the nozzles (QV). Other measurements in the laboratory model show that gradients in the impact-pressure wave are directly proportional to the jet QV if the diameters of the nozzles are held constant. Consistency of the basic relationships through changes in the Reynolds numbers of the jets from 31,000 to 93,000 suggests that the laboratory results should be representative of typical flow in field operations having higher Reynolds numbers. Estimates of the impact-pressure waves under conditions other than those in the jet-bit model may be made by comparison with a less complex model—impingement of a jet against an unrestricted flat surface normal to the jet. Equations derived from current jet technology describe the wave in this simple system for a wide range of conditions. INTRODUCTION The efficiency of rotary drilling operations is strongly linked to the efficiency with which cuttings are removed. Cuttings remaining on the bottom of the borehole will impede further penetration by the bit until they are removed. Wasteful regrinding is prevented if the fluid circulated past the bit removes cuttings as rapidly as they are made. Most investigations of bottom-hole cleaning under bits have been concerned with the rate-of-penetration effects of bit type, nozzle configuration, fluid properties, pressure gradients and utilization of hydraulic horsepower. These investigations have shown that drilling muds, weighted to keep the pressure in the borehole greater than in adjacent formations and carrying material which forms a filter cake, apparently plaster cuttings against the bottom, making them difficult to remove. In addition to a demonstration of the factors causing poor cleaning, the most significant result of these previous investigations has been the increased use of jet bits accompanied by better hydraulic programs and better selection of drilling fluids. Undoubtedly, these practices have improved bottom-hole cleaning, but rates of penetration when drilling with muds are still often lower than would be expected with perfect cleaning." Although there is general agreement with the concept that increasing hydraulic energy at a jet bit often increases the rate of penetration by improving cleaning, research workers have differed as to the best criterion for evalyating hydraulics. Some lean toward maximizing the product of the rate of flow and the velocity through the nozzles (QV) others prefer to maximize the hydraulic horsepower at the bit;'"-' "till another says that neither criterion is universally suitable."' This controversy shows that conclusive field evidence has not established the superiority of either of these criteria. Analysis of the fluid flow which cleans the bottom should contribute to resolving the controversy. Impinging jets clean the bottom by creating two mechanisms capable of dislodging cuttings. One is the impact from the momentum of the jet and the other is the flaw parallel to the bottom away from the area of impingement. The impact force appears in the form of a pressure wave on the bottom and, in this paper, is called the impact-pressure wave. The flow parallel to the bottom is called crossflow. Fig. 1 illustrates these two mechanisms. This paper describes crossflow and the impact-pressure wave beneath jet bits and relates them to controllable parameters. Through these relations, criteria for use in designing hydraulics to achieve maximum use of the mechanisms of cleaning are derived. PROPERTIES OF CROSSFLOW CONCEPTS DEVELOPED IN PREVIOUS INVESTIGATIONS Concepts of scavenging the bottom by crossflow have been well discussed by Bobo, et al." They examine the means by which crossflow may create forces on cuttings and conclude that the cleaning action of crossflow can be increased by increasing the velocity of the flow stream close to the bottom. Using boundary layer theory, they indicate that a reduction in the viscosity of the drilling

Jan 1, 1965

By K. A. Natarajan, I. Iwasaki

With a platinum electrode the Eh-pH response in aqueous systems follows an empirical relation [Eh = E- 0.059 pH](1) where E usually carries a value between 0.8 and 0.9 v. The same potential (E) is observed with a number of other noble metal electrodes in the absence of surface poisoning and of other well-defined redox couples. Many sulfide mineral electrodes also respond in a similar manner in solutions containing their respective ions over wide pH ranges, especially in the alkaline pH region. Such a parallelism between noble metal and sulfide mineral electrodes points to certain implications of their surface conditions, and the flotation and leaching behaviors of sulfide minerals under aerated conditions may be inferred with respect to the foregoing Eh-pH response. Comparison of Sulfide Mineral and Noble Metal Electrodes [Fig. 1] shows the Eh-pH response of pyrite, galena, chalcocite, and pyrrhotite electrodes, reported by Sato, and some experimental points obtained with a platinum electrode in distilled water. [Eq. 1] is seen to be followed by all these electrodes. It is interesting to note that the response of the pyrite electrode as shown is identical to

Jan 1, 1973

By Zay Jeffries

EACH generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwith-standing their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization.

Jan 5, 1924

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By A. L. Holley

IT has been customary at our opening sessions, for the presiding officer to address you on the general development of one or another of our several professions, or upon some important feature of Mining or Metallurgical Engineering. It is somewhat embarrassing to his successor that our former President, Dr. Raymond, expert as he is in every one of these professions, has been accustomed to keep them all, in their turn, prominently before you. In selecting for this occasion a subject necessarily connected with iron and steel, I have thought that a review of these manufactures, with reference to some of their more pressing needs for improvement, will be more timely than a general or statistical paper. I shall endeavor to confine my remarks to a few specific defects of practice and management, and to their equally specific and more or less developed remedies. That serious defects exist ; that they must be remedied ; that the manufacture is indeed already on the verge of transition, will be generally admitted. But it cannot be revolutionized all at once, however desirable the technical results might be, for that would bankrupt the business at large. We cannot afford to pull down and rebuild all our blast-furnaces that do not make a ton of pig iron with 25 cwt. of fuel ; nor to replace all our hand-puddling furnaces with revolving ones, even if we could select the best revolver. Although the soft steels promise to supplant iron for most structural purposes, there are neither money nor present market to warrant all at once replacing our iron works, or half of them, with steel works. Since, then, these manufactures can neither standstill nor be suddenly metamorphosed, their managers are saying to one another " We must feel our way into larger development ; we must work gradually into better practice; we must improve a little at a time." * President's address on the opening of the Cleveland meeting.

Jan 1, 1876

By Andrews Allen

THE large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc. have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired hoisting tonnage can be secured and, since only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining.

Jan 2, 1921

By A. L. Holley

It has been customary at our opening sessions, for the presiding officer to address you on the general development of one or another of our several professions, or upon some important feature of Mining or Metallurgical Engineering. It is somewhat embarrassing to his successor that our former President, Dr. Raymond, expert as he is in every one of these professions, has been accustomed to keep them all, in their turn, prominently before yon. In selecting for this occasion a subject necessarily connected with iron and steel, I have thought that a review of these manufactures, with reference to some of their more pressing needs for improvement, will be more timely than a general or statistical paper. I shall endeavor to confine my remarks to a few specific defects of practice and management, and to their equally specific and more or less developed remedies. That serious defects exist; that they must be remedied ; that the manufacture is indeed already on the verge of transition, will be generally admitted. But it cannot be revolutionized all at once, however desirable the technical results might he, for that would bankrupt the business at large. We cannot afford to pull down and rebuild all our blast-furnaces that do not make a ton of pig iron with 25 cwt. of fuel; nor to replace all our hand-puddling furnaces with revolving ones, even if we could select the best revolver. Although the soft steels promise to supplant iron for most structural purposes, there are neither money nor present market to warrant all at once replacing our iron works, or half of them, with steel works. Since, then, these manufactures can neither stand still nor be suddenly metamorphosed, their managers are saying to one another: " We must feel our way into larger development; we must work gradually into better practice; we must improve a little at a time."