Search Documents

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-'. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.' Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.' In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and washability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semianthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations.

Jan 8, 1954

By W. T. Cardwell

Physically absurd, triple-valued saturations appear in the straight-forward solution of the Buckley-Leverell equations for the displacement of oil by water or gas. From an engineering viewpoint, the triple value causen no difficulty. It is well known how it may be compensnted in order to obtain physically meaningful, numerical results. From a scientific viewpoint, the question still arises: What did the triple value mean? This paper explains how and why the triple value arose in non-capillary Buckley-Leverett theory. The discussion should serve as a background for the understanding and use of the modern method of characteristics in di.~pkzc(>ment theory. INTRODUCTION Displacement theory was introduced to petroleum technologists in 1 941 by Buckley and Leverett.' Their first equation, which they wrote down without derivation, was equivalent to the following: ?s/?t= - qr/F ?f/?r (1) where S = saturation of displacing fluid (a fraction) r = time q,. = total volumetric velocity of both the displacing phase and the phase being displaced (usually, but not necessarily, assumed to be a constant) F = porosity (a fraction) f - fraction of the total volumetric velocity that is the volumetric velocity of the displacing phase (assumed to he a function of S only x = distance. Buckley and Leverett called Eq. I "a material balance equation". Actually it is derived from both a continuity equation, or material balance equation, and Darcy's law. Buckley and Leverett jumped from their Eq. 1 immediately to their Eq. 2, which was the equivalent of the following: (?x/?t)x = qr/F df/ds = qr/F f'(s) (2) The jump from Eq. 1 to Eq. 2 involves apparently simple mathematics, but in that apparently simple mathematics lies a subtle point that is part of the key to the meaning of the triple value to be discussed here. Eq. 2 may be readily interpreted as saying that a point of constant saturation (on a saturation-vs-dis-tance curve) moves with a constant velocity that is proportional to the total volumetric rate, inversely proportional to the porosity, and is otherwise a function of the saturation itself. So that if one knows the derivativc with respect to saturation of the fractional flow function, f(S), for each saturation, one knows the velocity of each point of the moving saturation-vs-distance curve. The function f(S) can he determined experimentally and its derivative f'(S) can be calculated. It turns out that the experimentally derived f'(S) is not a monotonic function of S, but instead it has a definite maximum and declines away at both high and low saturations. This in turn means, in accordance with Eq. 2, that on a moving saturation-vs-distance curve, ccrtain intermediate saturations will travel faster than the saturations either higher or lower. The result is indicated in Fig. 1. In Fig. 1, the abscissas represent distances along a column of porous medium, which column is assumed to be uniform in cross-section perpendicular to the ab-scissal direction. The ordinates represent fractions of pore space occupied by the displacing phase, which may be either water or gas. It is assumed that the saturation is uniform over all planes perpendicular to the abscissal direction. The saturation is a function only of time and one space variable. Time variation of the saturation is represented by change in shape of a curve such as curve AGJ, which represents the initial saturation-vs-

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By W. F. Holbrook, C. E. Wood, E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and .its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. TYPES OF FURNACES Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1938

By L. I. Cothern

THE introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various "wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these, advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By Augustus Locke

THE technical sessions at the Regional Meeting of the A.I.M.E. in San Francisco are to be de- voted LO changes, current or predictable, which may be expected to alter today's practices in mining and metallurgical engineering. Our present condition may be summarized as follows: Capacity to produce is excessive for domestic needs in molybdenum, copper, iron, and oil; sufficient in lead, zinc, and potash; deficient in aluminum, manganese, tungsten, chromium, and tin. Gold and silver are complicated by their use as money. Or, to look at it in another way, the "growth curles" of production, as C. K. Leith emphasizes, characteristically rise slowly at the beginning, show a second stage of rapid growth, and a third stage of leveling off. The third stage is already reached here in coal. copper, iron, lead, and zinc. But still in the second slage are oil, molybdenum, potash, and others.

Jan 1, 1939

With one shaft almost completed and another shaft being sunk, the scope of the Saskatchewan potash area is beginning to come into focus. Some 18 companies have reportedly leased more than four million acres to explore potash possibilities. PCA, farthest along, is located about 15 miles southeast of Saskatoon, and IMC has its project underway near Esterhazy in the eastern edge of the province. U. S. Borax and Chemical Corp. is also reported exploring the area. The field lies in the middle Devonian geological formation which was probed by oil companies along the 200-mile area across the province. Extensive examination began after World War II and deep drilling was started a few years later.

Jan 5, 1958

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

By George R. St. Pierre, John Chipman

METALLURGISTS have been studying the chem-ical behavior of sulfur in steelmaking for many years in order to have a better control of the sulfur content of finished steel. During the refining period in the open hearth, molten steel is separated from a gas phase by molten slag. Chemical reactions occur principally at the slag-metal interface and at the slag-gas interface. A need for physical-chemical investigations of reactions between sulfur-bearing gases and steelmaking slags was recognized some time ago.'.' From the early work, it can be qualitatively concluded that increased sulfur content and low partial pressure of oxygen in the gas phase favor the passage of sulfur from gas to slag. Using radioactive sulfur S Koch and Fink' have demonstrated the rapid rate of exchange of sulfur between gas and slag in an open hearth furnace. Gurry and Darken and Darken and Shields (as reported by Derge and Marshall') have equilibrated lime-iron oxide slags with SO—O2 gas mixtures. The major conclusion from the reported results is that sulfur content increases with increasing lime content in lime-iron oxide slags equilibrated with a gas of high oxygen pressure (10-2). The data were interpreted as indicating the presence of SO, and S,O, ions. Richardson and Fincham' have conducted the most extensive experimental study of sulfur equilibria between gas and slag. Their results confirmed many of the conclusions drawn from calculations of Richardson" and Withers. Richardson and Fincham's data fitted very well into the sulfur scheme represented by the reactions 1/2 s2 (g) + (0) melt - 1/202(g)+ (S) melt [II 1/2 S, (g) + 3/2 O (g) + (0) melt - (SO,) melt. [2] At oxygen pressures greater than 10 to 10 they found that reaction Eq. 2 was predominant while reaction Eq. 1 was controlling at oxygen pressures less than 10." to 10.". The slag compositions and gas mixtures used in their investigations were different from those used in the present study. Wherever possible, comparison has been made between their results and these, and agreement is excellent. It is evident that the distribution of sulfur between slag and gas depends upon the oxygen pressure of the gas. In FeO slags, a change in oxygen pressure produces a change in ferric oxide content, and a knowledge of this equilibrium is a prerequisite to studies of sulfur distribution. The data are found in the work of Darken and Gurry" on the FeO system and the more recent experiments of Gurry and Darken" and of Larson and Chipman" on FeO slags containing lime and silica. The effect of oxygen pressure on the ratio Fe /(Fe" + Fe ), the so-called j-ratio, reported by these investigators will be used in interpreting the results which follow. Experimental Method The purpose of the experimental program was to determine the equilibrium sulfur content in slags exposed to gases of known oxygen and sulfur pres- sures. The slag compositions selected for study were from the lime-silica-iron oxide system. Additions of magnesia were made to some of the slags. Apparatus—The apparatus used by Larson and Chipman was modified slightly to accommodate the addition of SO2 to the gas mixtures. As in their work, slag samples of 0.5 to 2.0 g were held at temperature (lcc) in platinum crucibles under a steady stream of gas, 100 to 200 ml per min, for several hours and then rapidly lowered to the bottom of the furnace where they were quenched in mercury. Preparation and Analysis of Gas Mixtures—Mixtures of SO,-CO were prepared from Virginia Smelting Co. Extra Dry liquid SO, and Pure Co. CO,. After removing traces of water vapor with an-hydrone, the CO, was passed over graphite at 1200°C, at which temperature the conversion to

Jan 1, 1957

By C. Dalton, H. L. McGill

The purpose of this study was to develop a method for predicting the time delay created by metering a fluid through an annular restriction with translational motion of the boundaries. This time delay is utilized to control the opening of valves in various down-hole oilfield tools and forms the basis for the "hydraulic jar". The hydraulic jar is used to give upward impact forces to tubing or other tools that become lodged down-hole. The design of these jars has primarily been by trial and error; varying the clearances, fluid viscosities and dimensions of the jar until a satisfactory time delay was achieved. Obviously, a better understanding of the fluid flow characteristics is required to produce designs that are satisfactory and to eliminate the trial-and-error approach. Previous studies of flow in annular spaces were based on constant length of the annular restriction. Any motion of the boundaries of the annular space was confined to a rotational motion, like that encountered in journal bearing design. Consideration of the effect of translational motion of one boundary with respect to the other was necessary in applying this previous work to a time delay device. A prediction method was developed that takes into account this relative translational motion. Equations were developed to predict the relative velocity, the flow rate, and the time delay in a concentric annular space. The effect of eccentricity also was included. Experimental data were obtained and closely correlated with the prediction method. This correlation is presented graphically in terms of predicted and actual relative velocities for various annular clearances and pressure drops. This extension provides design equations which predict the performance of the hydraulic jar, thereby eliminating trial-and-error solutions and reducing the development time required for satisfactory designs. INTRODUCTION The design of down-hole oilfield tools which use hydraulic delay systems based on flow through annular orifices with relative motion of the boundaries is usually a trial-and-error process. The annular clearances, fluid viscosities and dimensions of the mechanisms were varied until satisfactory delay times were obtained. The development of these tools has been expensive, and a better understanding of the characteristics of annular flow with relative motion of the boundaries could result in superior and less expensive designs. The purpose of this investigation was to provide a method of predicting the performance of down-hole tools which use annular flow and, in particular, the performance of a down-hole tool known as the "hydraulic jar". The hydraulic jar is used to free pipe, packers and other tools that become lodged down-hole. The jar, located in the tubing string between the surface and the object which is stuck, releases the object though the repeated application of upward impact blows. The jar is basically a slip joint that is restrained in a collapsed condition until the desired tubing tension has been developed. The slip joint is then released and accelerates rapidly until it shoulders, delivering an impact blow or jar to the object. The delay obtained by metering the fluid through the annulus formed by the jar valve and housing provides the time delay necessary to stretch and apply tension to the tubing or pipe. Fig. 1A gives a schematic diagram of the hydraulic jar and brief details of its operation. The metering of the hydraulic jar begins when the tension force being applied to the jar by the pipe creates a pressure differential across the valve that is approximately equal to the force divided by the displacement area of the valve. This pressure differential induces flow through the annular restriction formed between the valve and housing. The valve moves with respect to the housing as the

Jan 1, 1969

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The effects of ternary and quaternary additions of aluminum, oxygen, and carbon on the mechanical properties of high-purity titanium-molybdenum alloys were studied for several microstructural conditions. Heat treatments were designed to produce 1) ß-quenched, 2) equiaxed ß) transformed (acicular) and 4) stabilized -P microstructures. Tension, impact, and hardness tests were performed. Transformations from the ß phase were followed by hardness measurements and metallography. The ß-to-w transformation was slowed by aluminum additions; carbon and oxygen additions increased the transformation rate. In addition to solid-solution strengthening, these solutes may increase or decrease strength by altering the /3 transformation kinetics. Aluminum additions promote the formation of strain-induced martensite, and lower yield strengths at compositions near 12 pct molybdenum.. a-P alloys are more ductile with equiaxed than with transformed microstructures. High strength levels can be reached by aging in many cases. Strength levels of the aged specimens usually are lowered slightly by straining prior to aging. ALLOYS of molybdenum with titanium form an iso-morphous alloy system which has been the subject of several investigations. Additions of substitu-tional and interstitial -stabilizing elements provide means of improving mechanical strength and con- trolling the heat-treatment response of the binary alloys. The work reported here forms a part of a continued study of the effects of microstructure on the mechanical properties of high-purity titanium alloys. Previous papers have considered the various binary alloys (Ti-Mo, Ti-Al, Ti-C, and Ti-0) that form the bases for the ternary and quaternary alloys included here. The compositions were selected to correspond with the previous binary alloys. Further, the high purity of the alloying components was maintained, so that direct comparisons with earlier work can be made. The total research program included a large number of compositional, microstructural, and testing variables. The data reported here have been selected to provide a reasonably complete and representative summary of the results. The reader is referred to the original Air Force Report for a complete tabulation of the results. EXPERIMENTAL PROCEDURES All the alloys used in this work were prepared from high-purity electrolytic titanium produced by the U.S. Bureau of Mines. A typical furnished analysis showed the following impurities in wt pct, balance This analysis is equivalent to that of iodide-refined titanium. In addition, hardness, tensile, and impact tests made using unalloyed electrolytic titanium showed it to have properties equivalent to those obtained with iodide titanium and suitable for these studies of high-purity base alloys.

Jan 1, 1962

By John F. Abel

In the debate between miners and ecologists, our industry has at last begun to get some of its story told. I have been told many times that it is hopeless to even try to get our side across. Some are sure that no one will believe us even when our cause is just. My reply would be that we have to tell the truth; again, again, and again. We will never convert a fanatic, but we must try to reach the reasonable and thinking people. I am encouraged because more of us are trying. Various mining companies here in Arizona have bought newspaper space to set forth some of the facts around our local environmental problems. The Arizona Mining Association co-sponsored a symposium in March: Mining and Ecology in the Arid Environment. The symposium program included tours arranged with local mining companies. The participants saw an acid plant, an acid leaching operation, an alluvial tailings dike, a tailings pond, a smelter, and a couple of open pit mines. This wouldn't phase you until you realized that half the visitors were ecologists, watershed and wild- life managers, and other assorted conservationists. It took a lot of guts. I am proud that we had that much confidence. As Pogo said, "We have met the enemy and they is us!" Actually, we met the enemy and they were just like us-concerned.

Jan 1, 1970

By Sir Lowthian Bell

WITH the exception of air and water, it is open to question whether there is any form of matter which the human race could less easily spare than iron. Short of going the length of asserting that, without this metal for an anchor or steel for the compass, the adventurous navigator could never have crossed the wide Atlantic, we may credit the locomotive' and the steamer, and hence iron, for that sequence of events which has peopled North America with the

Jan 1, 1891

By F. E. Bash

CONSTANTAN is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported acid the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a, process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts. against pure iron at 1500° F. (816° C.) with the cold-junction temperature at 0° F., or a proportional e.m.f. at temperatures near 1500° F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure

Jan 9, 1919

By V. A. Phillips

Transmission-electron micrographs of electro-thinned samples of bulk-aged Cu-3.1 pet Co alloy show an aging sequence, supersaturated solid solution — coherent particles — quasi -coherent particles — noncoherent particles. Hardening is due to precipitation of coherent spherical fee coball-rich particles showing coherency strain fields, which are resolved at between 15 and 30A diameter. Loss of- full coherency did not occur until well into the overaged region, even with the assistance of deformation after aging. Different average particle diameters of 123, 92, and 149 ± 10Å were observed in samples aged to peak yield strength at 600°, 650°, and 700°C, respectively, indicating that there is no critical size for peak hardening. Noncoherent particles tended to develop (111) faces and became octahedral in shape. Dislocations tended to nucleate spherical coherent particles which eventually grew together forming large elongated particles. The surface energy of a noncoherent (low-angle) inter-phase boundary is estimated to he about 50 ergs per sq cm. A number of particle lining-up phenomena were observed. Overaging is principally attributed to increase in particle spacing, progressive loss of coherency, and increase in amount of discontinzdous precipitation. COPPER dissolves about 5.6 at. pet (5.2 wt pet) of cobalt at 1110oC1 and the solubility decreases to 0.75 at. petl (0.54 at. pet)2 at 650°C and to 0.1 at. pet or less at lower temperature.' It has been known for many years3-5 that Cu-Co alloys are capable of age hardening. Since cobalt is fee above 417°C and its atom size is only about 2 pet smaller than that of copper, precipitation of coherent particles would be expected. The equilibrium phase precipitated at 700°C and below contains about 10 pet Cu in solution which tends to stabilize the fee structure, lowering the transformation temperature to 340oc.l The alloy is known to undergo discontinuous precipitation in addition to general precipitation; while the former can be seen with an optical microscope, the latter precipitates are not visible except in the grosly overaged condition.5, 6 Extensive use has therefore been made of the ferromagnetic properties of the precipitate in order to follow the course of aging, and it has proved possible to measure the average particle size, spacing, approximate shape, and volume fraction and to determine that the particles are coherent without ever seeing a particle (see for example Refs. 2, 7, and 8). The magnetic measurements of particle size are limited to diameters below about 120Å.7 The present study was undertaken using the techniques of transmission-electron microscopy in order to check the above conclusions, to extend the previous magnetic work to larger particle sizes, and to attempt a more detailed correlation of properties and structure. A portion of this work has already been published.9-11 The present paper is concerned with the metallographic features of precipitation in relation to aging curves. Bonar and Kelly12'13 have published preliminary results of a similar study on single crystals of Cu-2 at. pet Co. EXPERIMENTAL Preparation of Alloy. A Cu-Co alloy, containing 3.12 wt pet (3.36 at. pet) Co by analysis, was prepared from 99.999 pet purity oxygen-free copper and electrolytic-grade cobalt. The alloy was melted and cast in vacuo in a high-frequency furnace using a graphite crucible and mold: Analysis showed chat 0.004 pet C was picked up during melting. The 1-1/2-lb ingot was homogenized in hydrogen for 24 hr at 1000°C. Slices were cold-rolled to 0.005 or 0.003 in. thickness, with an intermediate 650°C anneal in hydrogen at 0.080 in. thickness. Batches of six to ten strips were solution-treated in sealed-off quartz tubes in high vacuum in a vertical furnace and quenched by dropping into iced brine containing a device which snapped off the nose of the tube. Solution treatment consisted of 1 hr at 990°C or 2 hr at 965°C. The latter was employed for all mechanical-property studies, since a tendency was noted for the higher temperature to give porous material. Strips were usually aged individually in a horizontal vacuum furnace, inserting into the hot zone and withdrawing into a cold zone without breaking the vacuum. This method gave a rapid heating rate, permitting the use of short aging times. In some cases, particularly for the longer aging times at the higher temperatures, samples were sealed individually in quartz tubes in high

Jan 1, 1964

By R. W. Kobler, D. A. Dahlstrom

Since the development of the pelletizing process in the fifties for relatively high purity pellets from low grade taconites, there have been several distinctive changes in filter construction for the dewatering step preceding balling. In the original large pilot plant run by Reserve Mining Co. in Babbitt, MN, the disk type filter employing agitation (Agidisc filter) was selected as the most economical. Size was limited to 2.1 m (6 ft, 9 in.) in diameter. The second generation occurred in the sixties with a jump to 2.70 m (8 ft, 10 in.) in diameter to reduce capital costs per annual ton of pellet. In the early seventies, the third generation was the steam drying disk filter which became necessary to achieve balling moistures with specific surface areas of 2200 cm2/g to as high as 3800 cm2/g caused by finer grinding to obtain higher purities. Finally, the fourth generation has recently been developed to reduce maintenance costs and further improve hydraulics to ensure minimum moisture contents.

Jan 1, 1980

By H. C., Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions. Prior to the war years Inspiration's costs of mining by block-caving methods were comparable to, or even below, the costs of some open-pit operations. By the end of the war these conditions were completely changed. Underground costs had risen steadily for labor and supplies. Difficulty was being experienced in finding competent underground men and underground development was almost hopelessly behind schedule. On the other hand, open-pit costs had been sharply reduced through the development of modern earth-moving machinery and plenty of labor was available for surface work.

Jan 1, 1950

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZ92, (formerly ASTM No. 17; also known as Dowmetal C or AM260) which was done under "Restricted" Project NRC-21, in 1942-1943, and reported, in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZ92 was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZ92, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray analysis. From this figure it may be seen that above approximately 375°C (707°F), AZ92 alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a. two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, and because of its solubility relations, AZ92 resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ92 alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1947