Search Documents

By A. W. Adamson

A model for transport processes in liquid mixtures is discussed which supposes that the elementary act involves a position exchange between two species and that the exchange is so confined by the solvent cage as to occur nearly isosterically. The rate-determining step, thus, is likened to a bi-molecular reaction and is so treated, using absolute rate theory. The cage model has been applied to diffusion, thermal diffusion, sedimentation and viscosity, but only the first and last of these phenomena are emphasized in the present paper. The model leads to semi-empirical relationships between the absolute value for a digusion coefficient and the activation energy for diffusion, between mutual and self-diffusion coefficients and for the variation of the viscosity of a binary mixture with composition. These are discussed in relation to experimental data for various systems, including hydrocarbon mixtures. It is shown that the proposed viscosity equation and seven other commonly used ones all may be regarded as special cases of a single general relationship; a brief critical analysis is made of the basis of selection of one or the other for data fitting or interpolation. INTRODUCTION AND GENERAL THEORY The present paper covers a brief discussion of a cage model for transport processes in liquid mixtures and how this model may be useful in treating the diffusional behavior and the viscosity of such systems. Since diffusion requires the more detailed treatment, it will be taken up first, and the model then applied to viscosity. There are two types of diffusion coefficients that may be measured experimentally, apart from thermal diffusion quantities. The first is the mutual or binary diffusion coefficient, D which may be defined in terms of Fick's first law. This states that the permeation, or flux P, is proportional to the concentration gradient. In the usual experiment, P is measured relative to a frame of reference fixed with respect to the medium (e.g., the diaphragm in a diffusion cell); as a consequence, the same value of D is obtained regardless of whether P and C refer to Component 1 or to Component 2; i.e., there is only one independent mutual diffusion coefficient for a binary system. In addition to D there will be various self-diffusion coefficients. defined in terms of the gradient in labelled species i and its permeation in an otherwise uniform medium. The thermodynamic approach to mutual diffusion supposes that the actual driving force is the gradient of the chemical potential, i.e., that In the case of a dilute solution of solute, Eqs. 1 and 3 lead to the Einstein equation, If the solution is ideal and the friction coefficient is taken to be then the familiar Stokes- Einstein equation results. Mutual and self-diffusion coefficients can not be related on general thermodynamic grounds; it is necessary to invoke some additional assumptions, i.e., a model; several such have been proposed. Hartley and Crank' supposed the existence of separate, intrinsic diffusion coefficients (Dl and D2) for each component, essentially corresponding to the two self-diffusion coefficients. The two flows can not be independent, however, but must be coupled through the usual restriction that there be no net volume flow. For an ideal solution. one then obtains' Glasstone, et al' treated diffusion in terms of absolute rate theory, but their approach otherwise resembled the previously mentioned one in that each species was considered to move with respect to the general medium in a manner determined by its individual jump distance and specific rate constant. For other than dilute solutions, a coupling of flows leading to an equation such as Eq. 6 would again be present. However, as required by Eq. 6, one does expect that the self-diffusion coefficient for the solute and the mutual-diffusion coefficient for the system become identical at infinite dilution. Lamm4 recognized that there should be three distinctive interactions in a two-component system-1-1, 1-2 and 2-2 — and, therefore, proposed three rather than two fundamental friction coefficients. Mutual diffusion resulted from 1-2 interactions only, and self-diffusion resulted from 1-2 plus either 1-1 or 2-2 interactions. Again, a collective coupling between all motions was imposed to meet the condition of no net volume flow. Laity' has shown how to convert the Onsager equations to a form very similar to Lamm's. Cage Model For Diffusion Work in this laboratory on diffusion in aqueous sucrose solutions made it apparent that three, rather than two, interactions were indeed needed," but considera-

By R. L. Doan

WHEN the Plutonium Project was started in the spring of 1942 there was no technology to produce uranium metal of the required purity. Not only was there no such metal available; no one knew how to make it or fabricate it after it was made. Since this time vast technical effort has been ex-pended in the atomic energy field. A short 15 years later the metallurgy of uranium is probably better known than that of any other metal, with the possible exception of steel. At the beginning of the 1942 drive to obtain pure uranium metal the most available raw material was black uranium oxide (U3O8) of about 92 pct purity from the Great Bear Lake region of Canada. It took only three months for the project chemists to develop a process for bringing the purity of this oxide up to 99+ pct and another three months for Mallinckrodt Chemical Co. of St. Louis to build the purification plant and get it into operation. In early summer of 1942 the purified brown oxide (UO2) started moving to the Metal Hydrides Co. in Beverly, Mass., and to the Westinghouse Research Laboratory in Bloomfield, N. J., both of which had been granted Government contracts to try to make pure uranium metal.

Jan 9, 1957

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By L. F. Marek, G. W. King, A. Bogrow

THE purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction Of FeO to Fe. Unless the gas has a CO/CO2 ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available) the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity f the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"-i.e., the efficiency of conversion of the "available" CO supplied-is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size Of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1947

By Joseph B. Perry, G. M. Kirwan

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40º to 75 º. Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938

By Charles S. Barrett, Hermann F. Kaiser, Robert F. Mehl

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779° C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By J. K. Elliott, P. H. Kelly

Many engineering functions such as surface metering work and laboratory compressibility check points involve the use of liquid densities of light hydrocarbon mixtures at various pressures and temperatures. However, at the present time, no simple reliable method exists for determining density variation, particularly if the composition of the liquid is unknown. Consequently, a study was undertaken to develop and present a simple and accurate method of predicting density variation of a light hydrocarbon liquid with pressure and temperature, knowing only the density of the liquid at some condition. The experimental liquid compressibility data from API Project 37 by Sage and Lacey' have been considered to be accurate within 0.5 per cent and cover a wide range of pressure (14.7 to 10,000 psia), temperature (100" to 400°F) and molecular weight (up to 150). From these data, a set of liquid density curves, which relate density to pressure, temperature and molecular weight, was developed. These curves make it possible to predict density variation with pressure and temperature. Compared to extensive laboratory compressibility data on a complex, light hydrocarbon liquid, the use of the liquid density curves resulted in an average error of less than 0.5 per cent. Based on the results of this analysis, it is concluded that the set of liquid density curves developed from the data of Sage and Lacey provides an accurate and simple method for predicting the density variation of light hydrocarbon liquids when the density at some condition is known. These curves should be very helpful in many engineering calculations, particularly in the surface metering of light hydrocarbon liquids. INTRODUCTION Many situations arise in field and engineering laboratory work, such as reservoir engineering studies, check of experimentally determined laboratory data and orifice flow-meter formulas, where liquid density factors at various pressure-temperature conditions are required. Also, the need for accurate light hydrocarbon liquid information has become more important with the advent of miscible-type displacements for secondary recovery purposes in oilfield operations. Several reliable methods are available1 - "or determining the density of liquid hydrocarbons if the composition of the liquid is known. However, there is a definite lack of methods for accurately determining the variation of density when the composition of the liquid is unknown. The purpose of this study is to review the various methods for determining hydrocarbon liquid densities and to develop a simple and reliable method of determining variation in density of light hydrocarbon liquids with pressure and temperature when the compositio~n of the liquid is unknown. METHODS FOR DETERMINING DENSITY OF LIQUIDS OF KNOWN COMPOSITION Sage, Lacey and Hicks' have proposed a method to predict the density of light liquid hydrocarbons by using partial molal volumes. Data are available on experimentally developed partial liquid volumes of hydrocarbons over a rather limited range of temperature, pressure and composition. The partial mold volume method has proved satisfactory for determining the density of some hydrocarbon liquids when the composition is known. Within the range covered in the Sage, Lacey and Hicks1 data, the results agree within about 3 per cent of the experimental values. Hanson mentions the limitation of this method to a composition range of approximately 10 per cent by weight of methane, which will not allow this correction to cover most low molecular weight-light hydrocarbon liquids. Standing and Katz2 studied data on light hydrocarbon-liquid systems containing methane and ethane at high temperature and pressure and have presented a method for determining liquid densities, assuming additive volumes for all components less volatile than ethane and using apparent densities for methane and ethane. The compressibility and thermal-expansion curves used by Standing are based on assumptions that compressibility of a hydrocarbon liquid at temperatures below 300°F is a function of the liquid density at 60°F and that thermal expansion of the liquid is affected little by pressure. The information required to use this technique with an example problem is furnished by Standing.' Hanson eports an average error of - 0.5 per cent using the method of apparent densities in calculating liquid densities of several volatile hydrocarbon mixtures. However, as implied, the apparent density method is not applicable for liquid density calculations when the composition of the liquid is unknown. Watson- as presented a method

By J. J. Gilman

THEORIES of fracture in metals have been based primarily on the dependence of fracture strength on grain size. This dependence was first observed by Masing and Polanyi.l These workers, as well as 0rowan12 and Davidenkov and Wittman,' thought the grain size could be equated with the crack size in the Griffith condition for crack propagation.4 In this way they could account for the observed proportionality between fracture stress and the reciprocal square root of the grain size. The chief results of recent investigations of the fracture strength of polycrystals are summarized in Fig. 1. Low for iron,5 Petch for iron,' Greenwood and Quarrel for zinc, Petch and Zein for zinc,' and Hauser, Landon, and Dorn for magnesium'' have all found that the fracture stress of a polycrystal is proportional to the reciprocal square root of the grain size. Also, they find that, for large grain sizes, the fracture stress lies near the extrapolation of the yield-stress curve determined at small grain sizes; where measurable plastic strain precedes fracture. Low9 has gone a step further and shown that, in Range 1, the fracture stress in tension is almost identical to the yield stress in compression for a given grain size. Homes and Gouzou, 10 and Low also have shown that, in Range 2 of Fig. 1, microcracks form when the yield stress is reached, but they do not cause failure until the stress reaches a much higher value. The fact that yielding always precedes fracture suggests that fracture is induced by plastic flow. A mechanism by which this might occur was first proposed by Zener.11 He pointed out that blocked dislocations would cause stress concentrations which might cause fracture. The blocking would be caused by grain boundaries. This idea has been developed by Eshelby, Frank, and Nabarro,12 by Koehler,13 and by Stroh.14 By means of etchpits blocked dislocations have been observed in brass by Jacquet,15 in zinc by Gilman,16 and in lithium fluoride by Gilman and johnston. The blocked-dislocation theory and the experiments that bear on it have been summarized by Mott.18 One of the strong points of the blocked-dislocation theory is that it can explain the grain-size dependence of the fracture stress in a natural way. However, Low9 has pointed out that the theory is not satisfying when it is considered quantitatively. Gilman10 also has criticized the theory and presented an alternative interpretation of the relation between fracture stress and grain size. Since the blocked-dislocation theory is not the only theory that can explain in the grain-size effect, it is necessary to find other evidence either to support or deny it. In this investigation the following points were studied: 1) If blocked dislocations normally cause fracture, then the fracture stress ought to be very high in the absence of plastic glide. Is it? 2) If dislocations must be blocked in order for metals to fracture, then certain types of grain

Jan 1, 1959

By Carl Henrich

The Ducktown copper-mines are located in the southeast corner of Tennessee. The name Ducktown was originally given to a district occupying the southeast corner of Polk county, which in turn occupies the southeast corner of the State. Fig. 1 is a map of the vicinity of Ducktown, taken from the topographical surveys of the United States Geological Survey. The Ducktown district is bounded on the east by Cherokee county, North Carolina (the boundary-line between the two States running here a little east of north along the western slope of Pack mountain), and on the west by the eastern foot-hills of Little Frog mountain. On the north, Stansbury mountain, really a chain of low mountains or hills, forms the dividing-line between Ducktown and Turtletown districts. On the south, the Ducktown district extends beyond the Ocoee river to the Georgia State line.. This line, in going west, gradually recedes southwards from that river into the foot-hills of Big Frog mountain, the highest mountain of the neighborhood, which rises about 4300 feet above sea-level, while the surface of the Ocoee river, where it leaves the Ducktown district, is less than 1500 feet above sea-level. It will be seen from this description, and from a study of the map, that the Ducktown district occupies the northern part of a kind of basin, bounded on the east by Pack mountain and on the west by Little and Big Frog mountains. Between these mountains the Ocoee river, draining the basin, cuts its way to the Hiwassee and the Tennessee rivers in a narrow gorge, through the crystalline slates and schists, which from their excellent exposure in this Ocoee gorge have received the local

Jan 1, 1896

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915; Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1983

By W. A. Backofen, M. L. Ebner

SINCE the early work of Gough with Hanson and Wright,l-3 the study of fatigue has been characterized by experiments on single crystals only in recent times.9-10 Now, increasing attention is given to this aspect of fatigue research for the insight that it may provide into details of mechanism. The investigations have concentrated to a large extent on the development of deformation markings on fatigued crystals, and have shown the cracks to originate in slip bands possibly preceded or accompanied by slip-band extrusions. Experiments of special interest to the present work were conducted by paterson5 on copper crystals and involved both metallographic examination and measurement of change in flow stress. Crystals were cycled in alternating tens ion-compress ion with a constant plastic shear-strain amplitude of approximately 0.8 pct, and were particularly revealing for their demonstration of hardening with accumulated strain similar to that in unidirectional straining, through an easy-glide stage I followed by a stage II of rapid hardening; deformation was not continued beyond 40 cycles, however, so that the eventual course of the hardening curve could not be decided. For the conditions used by Paterson, surface slip markings were similar to those observed in unidirectional straining, but there were no X-ray asterisms and no deformation bands on the surface. In current thinking about the nature of fracture in fatigue, two views relative to mechanism are generally acknowledged, with the reservation that both could apply simultaneously in some measure. As one possibility, fracturing across a slip plane is regarded as a result of loss of cohesion from the creation of many point defects by dislocation movement under the cyclic loading.'' On the other hand, fracture has also been taken to follow as a consequence only of the geometry of slip at a free surface, consisting of offsets and crevices which eventually become fatigue cracks.12, l3 The work of McCammon and Rosenbergl4 showing fatigue in polycrystals at 4.2oK makes clear that any long-range diffusion of point defects is unnecessary, yet studies such as those of Forsyth and stubington15 show that accelerated diffusion may be a characteristic of deformation under fatigue loading. Interest in obtaining data of possible use for resolving such questions led to the experiments described below. Copper crystals were conveniently loaded in alternating four-point bending at constant deflection, a test condition shown to approximate a constant plastic strain amplitude for a wide range of axial orientations. The method of testing was not readily adapted to extensive study of temperature effects, but an investigation of the geometry of crack formation could simply be made by orienting,the slip direction at different angles to the surface. EXPERIMENTAL PROCEDURES Single crystals were grown by a modified Bridgman method in a stationary gradient furnace under an atmosphere of purified dry nitrogen. Purity of as-grown crystals was 99.999 pct as determined by spectrographic analysis plus vacuum fusion and gravimetric analyses for oxygen and sulfur, respectively. Crystals were of reasonable perfection as evidenced by a critical resolved shear stress at 10 deg from (110) of 60 g per sq mm and half-width of a (400) X-ray diffraction line from one crystal of

Jan 1, 1960

By Charles Kumke

THE "slot" system of mining in use at the Golden Queen mine, Mojave, Calif., does not involve any new mining methods. It is, how-ever, a, new combination and adaptation of several stoping systems in common practice. The first plans for stoping operations at the Golden Queen mine called for ordinary shrinkage stopes. The hanging wall of the vein, where exposed, is a very hard felsite with a dip varying from 50° to 70°. The vein itself is quartz, shattered and fractured enough to make it easy to drill and blast to a clean hanging wall. There is no well defined footwall. The footwall limits had to be determined by assays as the metal content faded out into the felsite. Two shrinkage stopes, each approximately 200 ft. long, were laid out and started on the 200-ft. level. One of these stopes, varying in width from 8 to 18 ft., was carried on up to the top limits of the ore, approxi-mately 120 ft., without a break in the operation. The shrinkage system proved entirely satisfactory and low costs resulted from-this operation. In the final drawing of this stope, two timbermen followed down on the ore, scaling the hanging wall clean of small fragments and placing an occasional long stull from foot to hanging wall where it was deemed necessary. Few such stulls; however, were required. The hanging wall stood up very well until the stope was entirely emptied of ore. Waste fill was then put into the stope by the glory-hole method, through a waste raise that had previously been run to surface from the middle of the stope. The second shrinkage stope ran into difficulties about 35 ft. above the sill floor. Up to this point the maximum width of the ore had been about 15 ft. The ore suddenly widened into the footwall to a distance of 40 ft. in the north end of the stope. In extending the stoping operations over this width, it was soon found that the vein material would not arch and support itself. Drilling in this end of the stope was then entirely too hazardous, and all operations were stopped. The ore was drawn through the chutes below as rapidly as possible and as soon as the stope was entirely

Jan 1, 1937

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By Hans Lundberg

In order to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. For its operation, electrical prospecting mainly depends on the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1). The good conductor, chalcopyrite, in the poor conductor, schist, thus attracts the current and deflects the normal flow far outside the conduct-

Jan 1, 1929

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By T. L. McCall

THE late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd&apos;s paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20°. The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable out-side advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd&apos;s paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

By Yingchang Tsenshan Wang

UUIN L&SS 1» Paqb I. Introduction........................................................658 1. Subject and Scope...............................................658 2. Acknowledgments...............................................659 3. Review of Previous Work........................................659 Field Data...................................................659 Experiment.a1 Data............................................662 4. Plan of Present Investigation.....................................662 Method of General Procedure...................................663 I1. Experimental Work..................................................663 A. The Solution of Sphalerite..............................:........663 1. The Solvent Effect of Iron Sulphates upon Sphalerite...........663 2. The Solubility of Sphalerite in Salt Solutions of Silver, Copper and Lead...............................................668 B. Formation of Zinc Carbonates....................................674 3. The Reactions of Carbonates and Bicarbonates With Solutions of Zinc Salts............................................674 4. The Reaction of Zinc.Sulphate Solution With Limestones.......684 C. Peculiar Conditions Affectitig the Formation of Zinc Silicate (calamine) and Zinc Carbonate (smithsonite)..........................686 5a. The Effect of Carbon Dioxide Upon the Basic Silicate and the Carbonates of Zinc in Water, and Its Bearing Upon the Conditions of Theii Precipitation..............................686 5b. The Reactions of Solutions of Soluble Silicate With calamine and Smithsonite in Solution in Presence of Carbon Dioxide..689 6. The Reactions of a Mixture of Hydroxide and Silicate of Sodium with a Dilute Solution of Zinc Sulphate...................691 D. High-Temperature Methods.....................................692 7a. The Influence of Temperature on the Formation of Calamine..692 7b. Possible Effect of Heat on Calamine and Srnithsonite.........697 E. Summary of the Experimental Work..............................698 III. Petrographic Work....................................................700 1. The Occurrence of Sphalerite in Limestones or in Cherts............701 Summary of the Blende in Limestones and in Cherts.............7432 2. The Partially Altered Sphalerite and the Oxidation Products........702 a. Smithsonite with Blende....................................702 b. Calamine with Blende......................................703 c. Smithsonite and Calamine..................................703 d. Summary on the Partially Altered Sphalerite and Its Oxidation Products..............................................704 IV. Concl~~siom ........................................................-705 V. Microphotographs and Photographs with Their Explanations.............705

Jan 1, 1916

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970