Search Documents

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By H. H. Klepfer, K. J. Gill, P. Chiotti

SOME observations relative to the U-Zn system have been made by other investigators. Chipman1 and Carter2 have reported the preparation of several U-Zn alloys and point out that these alloys are generally difficult to prepare. Chipman1 reported evidence for a high melting compound at about 90 atomic pct Zn and the possible existence of a eutec-tic between the compound and uranium. Raynor," in a theoretical discussion of the alloying properties of uranium, included zinc among the elements predicted to have little or no solubility in a, p, or y uranium. In the present investigation, thermal analyses, X-ray, metallographic, and vapor-pressure data were obtained to determine the phase boundaries. The relatively high zinc pressure over most of the alloys at temperatures of 900 °C and above proved troublesome and special techniques had to be employed in preparing suitable alloys. Materials and Preparation of Alloys The metals employed in this investigation were Ames Laboratory biscuit uranium containing less than 500 ppm total impurities and Bunker Hill slab zinc or Baker Analyzed reagent granulated zinc, both with a purity of 99.99+ pct. Due to the high vapor pressure of zinc and the high reactivity of both uranium and zinc with oxygen at only moderately high temperatures, alloys were prepared in closed containers which had either been evacuated or evacuated and filled with helium. High purity magnesia, magnesia containing 10 pct calcium fluoride, and tantalum proved to be suitable crucible materials. Tw-o different procedures, described below, were used to prepare alloys, the latter being the most satisfactory. The metals, uranium turnings and granulated zinc, were cleaned with dilute nitric acid, rinsed, dried, and placed immediately in a helium-fill'ed dry box. The two metals were placed' in a 10 mil Ta crucible. The charge was enclosed in the tantalum crucible by welding on a preformed tantalum cap. This assembly was enclosed inside a stainless steel (AISI 309) bomb. The bomb was made by welding a piece of stainless steel plate on each end of a stainless steel pipe. All these operations were carried out in a helium atmosphere. These assemblies were heated in a muffle furnace at temperatures between 1100" and 1200°C for 10 to 15 min or held as long as 15 to 20 hr in the 950" to 1000°C temperature range before quenching. Spectrographic and chemical analyses showed no tantalum pickup by the alloys, indicating no reaction between the alloys and the crucibles. However, some of these crucibles failed, probably due to imperfections in the welds of the stainless steel or tantalum crucibles. The second and most satisfactory method was to prepare the alloys by powder metallurgy techniques. The procedure was to press degreased and acid-etched uranium turnings with granulated zinc into 20 g compacts under 20,000-psi pressure. The compacts were placed in MgO crucibles, and sealed in evacuated Vycor or fused silica tubes. The alloys were then heated as long as two weeks at about 550°C in a muffle furnace. The pressed compacts were observed to expand by several volume percent during heating and it was necessary to make allowances for this expansion in order to avoid breaking the crucible and Vycor tube. This method was found very satisfactory for preparing alloys which were suitable for thermal analysis or vapor pressure studies. Experimental Methods and Results The phase diagram for the U-Zn system at 1 atrn pressure, shown in Fig. 1, is based primarily on vapor pressure measurements and on thermal analysis taken at temperatures below 950°C. Fig. 2 shows the U-Zn diagram at 5 atrn pressure, constructed on the basis of thermal analysis of alloys in sealed containers up to 1150°C and on the basis of metallographic, X-ray, and analytical data. The alloys sealed under vacuum were actually under their own vapor pressure and those sealed in an atmosphere of helium were under an additional pressure due to the helium. At temperatures up to 1100°C the zinc pressure is 5 atrn or less for these alloys; consequently the maximum pressure over the alloys sealed under a helium atmosphere was 10 atrn or less at temperatures up to 1100°C. Changes in pressure of this order of magnitude do not appreciably alter the position of most solid-solid or liquid-solid phase boundaries. In constructing the phase diagram for a pressure of 5 atm, the effect of pressure on all phase boundaries except those for liquid-vapor or solid-vapor regions was considered negligible.

Jan 1, 1958

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By G. W. P. Rengstorff, R. B. Fischer

A study was made of the effect of impurities on the bend ductility of cast molybdenum. High purity molybdenum was repared by re-melting under high vacuum. The ductility of "transverse-grain" specimens indicated that intergranular brittleness decreased with an increase in purity of the metal. THE production of as-cast molybdenum with high ductility at room temperature would make working of the metal easier and increase the usefulness of the as-cast metal. Furthermore, a .knowledge of the factors that influence the ductility of as-cast molybdenum might be applied to the problem of making fusion weldments having satisfactory room-temperature ductility. Individual grains of commercial as-cast molybdenum are slightly ductile at room temperature. However, the presence of carbides at the grain boundaries may cause the metal to fracture in a brittle manner. This behavior has been discussed.' The amount and distribution of the impurities in as-cast molybdenum would be expected, from previous research on the metal, to have considerable influence on its ductility. Some effects of oxygen and carbon on the mechanical behavior of the metal were discussed by Parke and Ham,2 Woodside,3 and Zappfe. Landgraf, and Worden.4 Parke and Ham2 found that, if a sufficient number of molybdenum oxide particles were present at the grain boundaries, the intergranular cohesion was reduced to the extent that arc-melted molybdenum would rupture intergranularly during hot forging. They also found that if the oxygen content was less than 0.003 pct, the cast molybdenum was hot forgeable. It is suspected, however, that forgeable molybdenum may contain a small amount of oxide that could reduce the ductility of the as-cast metal at room temperature. Also, there is the possibility of the unfavorable distribution of other impurities having a detrimental effect on the ductility of cast molybdenum. The results of a study of the influence of purity on the room-temperature ductility of cast molybdenum are presented here. Vacuum Arc-Melting to Produce High Purity Mo One way of determining the effect of impurities on the ductility of molybdenum is to prepare and test metal as free of all impurities as possible. Accordingly, the present investigation was undertaken with this in view. Arc melting in high vacuum (less than 0.1 micron of mercury) was chosen as the method for reducing the impurities below the concentrations occurring in commercial molybdenum. Commercial arc melting of molybdenum is carried out at about 50 microns pressure. During the arc melting, carbon and oxygen in the metal react to form carbon monoxide. By virtue of the vacuum process, the partial pressure of carbon monoxide is maintained at such a low value that the reaction greatly lowers oxygen and carbon contents. An excess of at least 0.03 pct C is used in commercial arc melting to insure that the oxygen content will be below 0.003 pct. The excess carbon remaining after the deoxidation step forms carbides on freezing. Some of the carbides precipitate at the grain boundaries and, as will be shown, have an unfavorable effect on the room-temperature ductility. In the present work, only the small amount of carbon (0.003 pct) contained in the commercial powder-metallurgy molybdenum used for melting stock was present. Partial removal of oxygen from the melt probably occurred as the result of the volatilization of molybdenum oxides, or by distillation of oxygen at the high melting tem-

Jan 1, 1953

By Frederic Dewey

HAVING shown1 the difficulty of assaying so-called cyanide bullion and the extreme variations often found in the results, an investigation was undertaken to discover if possible the causes of these variations by a series of tests upon the specific action of various metals during cupellation. Zinc.-In order to test the effect of zinc, 48 assays were made in sets of 6, 2 rows of 3. The charge for the middle cupels consisted of 500+ mg. Au, 1,125 mg. Ag, 10 mg. Cu. To the end cupels 50, 75, 100 and 125 mg. Zn were added, and a set of each proportion was cupelled with 4 and 8 grants Pb. The cupels were assayed and showed the following gold contents in milligrams, the figures being arranged as the cupels stood in the muffle: TABLE 1 50 Mg. Zn 75 Dig. Zn 100 Mg. Zn 125 Mg. Zn 4 grams, Pb 0.2S 0.25 0.2S 0:29 0.27 0.34 0.33 0.28 0.41 0.31 0:30 0.36 0.30 0.33 0.34 0.31 0.31 0.29 0.35 0.37 0.42 0.41' 0.34 0.38 8 grams, Pb 0.40 0.43 0.42 0.38 0.36 0.43 0.35 0.34 0.41 0.33 0.37 0.37 0.54 0.17 0.59 0.44 0.43 0.43 0.38 0.39 0.41 0.57 0.38 0.46 _ In many instances the zinc does not appear to affect the cupel gold, but various exceptions are apparent, generally in the cupels in the back row. With 100 and 125 mg. Zn, in some cases the Zn burned with its characteristic flame before it could alloy with the other metals. Also, less fusible oxidized lumps were observed during the cupellation and some cupels showed a scum. In order to lessen the premature burning out of the Zn, an alloy of 2 parts Ag to 1 part. Zn was used. A uniform charge of 500,+ mg. Au,

Jan 7, 1917

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.' Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.'' As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By H. L. Teicliman, E. M. Sipprelle

ENACTMENT of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming.

Jan 1, 1950

By C. G. Dunn

With respect to theories of recrystalliza-tion in metals plastically deformed. it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in poly-crystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins3 indicated that some data were consistent with primary nucleation OCcurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried Out at the Pittsfield Works' Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere.4 PReparation oF Specimens and Experimental Procedure The material used in the present investigation was taken from the same heat of steel as that .used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0,075 Mn, 0.03I A1 and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with 8-in. diameter rolls, the plane of the sample in each case coinciding with an XY plane (the plane of projection for the stereo-graphic plots) and the elongation occurring in the X direction. In general, elongations were held to about 3 or 4 per cent.

Jan 1, 1945

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969

By J. A. SINGMASTERN

THE New Jersey Zinc Co.'s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931

By G. V. Raymor, James T. Waber, I. Rex Harris

The lattice parameters of a series of fcc alloys of cerium and thorium were measured at 93 " and 298OK. Lattice parameters were also estimated for 171OK. Substantial deviations, y, from Vegard's law were observed. Although y was negative at the two higher temperatures, it was positive and large at the lowest temperature. A variety of models, which have been proposed in the past, were considered, and the calculated values of y were compared with the observed values. The best agreement was achieved with values computed with Friedel's equation. THE purpose of this investigation was to determine the effect of temperature on the lattice parameter and on deviations from Vegard's law of Ce-Th alloys. A large negative deviation from Vegard's law was first observed independently by Weiner, Freeth, and Raynor' and Van vucht2 in the room-temperature lattice parameters of Ce-Th alloys that form a continuous series of solid solutions. This observation was confirmed by Evans and Raynor. The allotropy of unalloyed cerium was reviewed recently by Gschneidner, Elliott, and McDonald. In two subsequent papers,5" these authors reported the influence of various alloying additions on the y= transformation, which occurs below room temperature. Although other rare earths tend to stabilize the double-hexagonal phase, thorium, plutonium, and scandium as solutes tend to stabilize the normal fcc phase. With addition of sufficient thorium as a solute, there is evidence that the formation of is suppressed and it becomes possible to pass continuously with decreasing temperature from the room-temperature phase to the fcc a phase. Thus there is a closed loop which is similar in many ways to the y loop well-known in ferrous alloys. A closed field also occurs in the pressure-temperature "equilibrium" diagram of unalloyed cerium. Because of interest in the effect of thorium additions and their influence on the a and phases, lattice-parameter measurements were made at low temperatures on the fcc phase for a series of alloys ranging from 10 to 90 at. pct Th. The results obtained at three temperatures are shown in Fig. 1. Evans and Raynors analyzed the deviations from Vegard's law in Ce-Th alloys in terms of changes in the occupancy of the 4f electron level in cerium,

Jan 1, 1964

By Paul Queneau

FEW of us who waded ashore on the Norman beaches realized the importance of coal to a successful invasion. General Eisenhower and his staff had been aware of the essential need for coal and an able Solid Fuels Section had been set up under the direction of Colonel Robert P. Koenig, of Indiana. This organization met the requirements of the invading armies on their march to the Rhine. East of the Siegfried Line enemy territory, the Army Engineers were called upon for assistance. When the Engineers were advised that, in addition to their normal duties, they were to occupy and place in operation the coal mines in the Twelfth Army group area, plans were drawn up overnight and action was initiated immediately. The Sixth Engineer Special Brigade, a versatile outfit which made a notable record D-Day on Omaha Beach, was selected to handle the operation. Within 48 hours of the new assignment an advance command post was set up cm the west bank of the Rhine at Homberg, just below German-held Duisburg. The 368th Engineer General Service Regiment was assigned to the Brigade, and the British 44th Pioneer Group, including specialist personnel, was also attached. This large British unit was added because most of the mines would shortly come within the British zone of

Jan 1, 1946

By F. B. Plummer

THE physical properties of oil-producing sands, such as grain size, porosity, and permeability, are becoming more and more important in petroleum production engineering as oil fields are being repressured and rejuvenated. A number of excellent papers have been published recently on all three of these properties. Faucher, Lewis and Barnes1 give a com-plete survey of the work done through 1932 and contribute also much information on sands that they themselves have examined. Muskat and Botset,2 Wykoff, Botset, Muskat and Reed,3 Hurst,4 and Muskat5 have contributed a great deal to the theory and actual measurement of flow of liquids and gases through porous media. Muskat and Botset have measured the permeabilities of different sands with gases and liquids. They find that the radial is always slightly under the linear permeability. However, in most of the previous experiments small samples of the sand were used, and the method of production of fluid or gas through the sands has not been very close to actual oil-field conditions. In addition, so far as the authors are aware, no measurements of linear and radial permeabilities have been made simultaneously under exactly the same conditions. The multiple permeability apparatus described here is a part of the equipment being acquired by this laboratory for thorough investigation of the physical properties of producing sands. It possesses certain advantages for comparative studies of liquid flow. Additional data and descriptions of other instruments will follow in papers to be written later on. The essential features of the permeability apparatus are as follows:

Jan 1, 1934

Discussion of the paper of Frederick W. Apgar, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 7S, June, 1913, pp. 1011 to 1022. L. C. GRATON, Cambridge, Mass.:-I presume I am one of the few who are exceedingly interested in microscopic work, and I am sure we have all enjoyed this paper very much. I will not attempt to express my own feelings in regard to it beyond saying that it seems to me that this sort of investigation and study has been overlooked and slighted, and its possibilities are very great. There are one or two, details which impressed me, because they were novel to me, and one was the development of secondary galena with dull luster. I have never seen any galena which seemed to be secondary, and have never seen any that was secondary or primary that did not have a bright luster. KIRBY THOMAS, New York, N. Y. (communication to the Secretary *) :-The present-day mining engineer is expected to " see into the ground farther than the point of the pick " and he is justified in making free claim to his ability to do so. Mr. Apgar has recorded the development of the application to the work of the engineer of a very useful but tardily recognized instrument-the petrographic microscope, an instrument which is helping to shatter the proverbial "point of' the pick" limitation-and he has shown its use and its possibilities very clearly. Some further field examples of the use of the microscope in engineering problems may add to the appreciation of Mr. Apgar's scholarly paper. In exploration by diamond drills in the Sudbury, Ontario, nickel district it is often of great importance to determine when the drill has passed out of the norite and into the foot-wall formation. Structural calculations may give a clue to the expected point of contact, but the variations are considerable, and, since to stop the drill before reaching the contact is futile, and too continue beyond it is needless, it becomes of theoretic and economic importance to determine positively the lithological nature of the corer at critical stages in the work. In some places the foot-wall is an earlier norite, only distinguishable from the nickel norite (Sudbury-: ite), by means of an examination of the rock slides with a petrographic; microscope. Again, certain diabase dikes which cut the norite and. the foot-wall formations cannot be easily or with certainty distin-

Jan 11, 1913

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 33? per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 Per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. Mine Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three a 13,800/440-volt, single- phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp motor on the No, 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 500-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft, Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. under normal operation the one pumping 1200 gal. per min, is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started1 and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the Pumps restart. On failure of any Of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 37' substation is run to the switching station, in which are four 15-kv., 600-amp. direct-current sole-noid-operated oil circuit breakers. The current for Operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1946

By M. S. King

A series of cross-hole acoustic measurements have been performed in a columnar-jointed basaltic rock mass around an underground opening mined by the drill-and-blast method. The purposes of the test program were: to evaluate the rock mass characteristics around the opening; to determine the zone of blast damage; and to evaluate seismic methods for anomaly detection ahead of mining in this type of rock. The cross-hole measurements were made between four 76-mm diameter horizon- tal boreholes diamond-drilled 12 m into a wall of the underground opening. Repetitive pulses of compressional (P) and shear (S) waves of frequencies in the range 3 kHz-100 kHz were propagated from a transmitter sonde through the rock mass to a receiver sonde, both of which were clamped hydraulically to the borehole wall. After amplification the received P- and S-wave signals were digitized at the surface by a digital oscilloscope and stored on floppy discs. The results indicate considerable reductions in P- and S-wave velocities at distances less than 2 m from the face. Clearly these low values are associated with blast damage. Beyond 2 m, the velocities in a vertical direction indicate almost constant values. The velocities in the horizontal direction beyond 2 m appeared erratic, but showed a general tendency to increase as a function of distance from the face. Their maximum values remained, however, still lower in value than the corresponding velocities in the vertical direction. Near the face, the differences in velocities were considerably greater: with horizontal velocities considerably lower in value than those vertical. Results of the spectral analyses of the received signals indicated that Q-values were strongly influenced by the vertically- oriented sets of joints. Only for waves travelling in the vertical direction was the effect observed of the blast-damaged zone immediately around the opening. The acoustic data obtained are clearly indicative of an anisotropic jointed rock mass, with a greater intensity of jointing for travel paths in the horizontal than the vertical direction. The vertical, columnar joints are probably less tightly closed than those oriented in the horizontal plane.

Jan 1, 1984

By J. L. Wyatt

The electrical resistance of titanium as a function of purity and temperature was measured from —325" to 2800°F. Two points of inflection in the data plots were found, and an increase in resistance with increase in temperature above the transformation was observed. IN 1948 Greiner and Ellis' reported on the thermal and electrical properties of titanium, including a study of the effect of temperature on the electrical resistance. The materials used in the research were obtained from the United States Bureau of Mines, where powder metallurgy techniques were being employed for consolidation purposes. These authors found a decreasing resistance with increasing temperature above 1625°F, and concluded that the latter temperature represented the point of transformation from hexagonal close-packed to body-centered cubic structure on heating. They reported a specific resistivity value of 55x10-6 ohm-cm, and showed that dp/dt was positive, decreasing with increasing temperature above ambient. In one of his early texts Hume-Rothery2 mentioned that certain metals, including titanium, exhibited minima in plots of resistance vs temperature. He indicated that this occurred at 212°F. Reporting many years ago on the effect of temperature on the electrical resistance of zirconium, de Boer and Fast³ showed that phase transformation in this sister metal occurred over a range of temperatures, the extent varying with its purity. Graphs of resistance vs temperature, showing transformation effects over a range of several hundred degrees, were presented for relatively impure metal. In the latter case the resistance decreased with increasing temperature throughout the region of partial phase transformation, thereafter increasing as predicted for normal metals by modern theories of the solid state. Since the quality of metal used in previous studies was substandard compared with iodide-type titanium, and in view of the fact that there seemed to be some rather unusual observations in the reported literature, it was decided to undertake a more extensive study of the thermal effects using high purity titanium, and to include temperature ranges beyond those which had been studied in order to ascertain whether or not the characteristics of zirconium would be duplicated. Experimental Materials Materials used in this investigation included commercial quality titanium (Ti-75A produced by the Titanium Metals Corp. of America) in the form of ¼ in. diam rods, and high purity iodide titanium (produced by the Foote Mineral Co.) in the form of crystal bar of irregular size. The latter was cold-swaged into rod form and machined to the desired size. Lead wires to all specimens consisted of 18 gage Ti-75A. Chemical analyses of the stock materials are given in Table I. Experimental Procedures Specimens 2½ to 3 in. in length were prepared with diameters nominally 0.15 to 0.20 in. Two holes,

Jan 1, 1954

By Olin M. Hart

Uranium ores occur in the Lower Cretaceous Inyan Kara group of heterogeneously stratified fluvial and fluvial-marine sandstones in the Black Hills of western South Dakota and northeastern Wyoming. There are three principal mining districts, each in the ancestral and present drainage area of a major river partially responsible for stripping the region to its present topographic form. Primary minerals in the deposits are coffinite and uraninite with minor amounts of paramontroseite and haggite. The ore minerals coat sand grains and fill interstices of complexly cross-stratified sandstone along solution fronts similar to "roll" type deposits of the other districts. Minerals of oxidized deposits are typically carnotite and tyuyamunite with different proportions of secondary vanadium accessory minerals. Ground water was the transporting medium and deposition of primary uranium and vanadium minerals occurred in reducing environments produced and controlled by physio-chemical characteristics of the sedimentary rocks.

Jan 1, 1968