Search Documents

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By H. J. Wasson

Published literature regarding the nation's oil reserve has been largely concerned with the estimated quantities in sight in known producing fields. This proved reserve has never been large in relation to demand. It has been the practice to consider the total future reserve (beyond that in sight within known fields) in the light of the broad potentialities of vast areas of partially explored sedimentary rocks, which are regarded as possible oil territory. Until recently, but little attention has been given to the rate at which the unexplored potentialities may be. converted into the proved reserve classification. To a certain extent, therefore, our contemporary viewpoint on the subject of national oil reserves is characterized by a pronounced contradiction. On the one hand, we measure known reserves as sufficient for only a few years of consumption—i.e., relative scarcity; on the other hand, we are confident that millions of unexplored acres will yield many new oil fields and that countless deeper productive formations underlie many of our known productive fields—i.e., infinite abundance. Of greater significance than the quantitative measure of either of these reserve classifications is the rate at which reserve replenishment must be accomplished in order to maintain an adequate time supply of proved oil reserves. The accumulation of geological data covering broad areas supports the belief that the remaining undiscovered oil reserve is exceedingly large. The distribution of oil in sedimentary formations of practically all ages, from Cambrian to Recent, is suggestive of almost unlimited possibilities; and the relatively small proportion of these possible areas that has been intensively explored in this country is a further index of the probable magnitude of the undiscovered future reserve. The implication that may reasonably be drawn from these observations is that oil, though distributed with less regularity and concentration than its related hydrocarbon, coal, nevertheless is a relatively abundant natural commodity of which the exhaustion appears remote. Final exhaustion of our oil reserve, if not infinitely remote, is a future contin-

Jan 1, 1937

By S. C. Carapella, E. A. Peretti

DURING a literature survey of the indium-zinc phase diagram, controversial reports on the composition of the eutectic point were encountered. The value reported in the investigation of Wilson and Perettil and in a later investigation by Valen-tiner' was 4.0 wt pct zinc. The most recent work recorded on this system consisted of an exhaustive survey of alloys by Rhines and Grobe8 in which they indicate a value of 2.8 wt pct zinc for the eutectic composition. To clarify this aspect of the diagram, a series of alloys were prepared by melting the respective constituents in a glass test tube under a covering of mineral oil and slowly cooling the melt in a furnace. The zinc used was Baker's C.P. and had the following analysis: insoluble in H2SO4—0.0l pct; pb—0.001 pct; Fe-—0.001 pct. The indium, which was supplied by the Indium Corporation of America, had a purity of 99.9'7 pet with the following impurities: Cu—0.002 pct; Pb—0.006 pct; Sn—0.01 pct; Zn—0.01 pct. The alloys were prepared for metal-lographic examination using a technique already reported' and a new value of 2.0 ± 0.1 wt pct zinc was observed. An alloy containing 2.00 wt pct zinc was also made by melting the constituents under a vacuum. In both of these methods of alloy preparation the losses can be kept extremely small. Again, the characteristic eutectic structure was obtained, assuring confidence in this value. The accompanying micrographs are presented in support of this point. Fig. la represents an alloy containing 4.00 wt pet zinc, and reveals excess zinc particles, which precludes the value of both Wilson and Peretti, and Valentiner. Fig. lb, gives the structure of an alloy containing 2.2 wt pct zinc, also showing the presence of excess zinc. Fig. lc is a micrograph of a typical structure of the eutectic observed in several sections of the 2.0 wt pct alloy. In the 1.8 pet zinc alloy, fig. id, the definite presence of the primary indium can be noted. From these re-

Jan 1, 1951

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors' paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.'' The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors' 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)' D = 3.55 x 10"3 exp (-5550/)' D = 4.3 x 10"3 exp (-5620/1')' Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By STEPHEN L. GOODALE

THE question indicated in this title was put by letter to a number of my friends working in various industries, who have charge of young metallurgical graduates. The replies were almost unanimous in stating that the college training should cover in the most .thorough manner possible those sciences which are the fundamentals - of engineering. Mathematics, physics, mechanics, electricity, chemistry, physical chemistry, and their applications to actual problems of life were mentioned in most of the letters I received. Some writers added also business law, economics,. and finance. One reply expressed it: "These subjects, well founded, mixed with good judgment, well applied, should enable the .young man to carry on the art of life successfully." One answer stated frankly what is really wanted: "As much as possible.' ' This writer mentioned .the sciences as being very important, but he wishes men ' to be trained in metallurgy also, and he concedes the omission of some advanced chemistry and physic's to secure the metallurgy. He emphasized particularly. the a we. desirability of work in college to development' He concludes his letter with a repetition of his slogan that what is wanted is as much as is possible.

Jan 1, 1930

By Byron W. Cheever

In working up the process which I described at the Chicago Meeting, May, 1884 (p. 163 of the present volume), for the estimation of phosphorus in iron and steel, I employed samples of steel obtained from one works only, and of a given brand. Since then I have had frequent occasion to test the process on other steels, and find that it works equally well. But some steels present certain colors which may mislead the operator; and I therefore propose a slight change in the directions formerly given. On the second page of my paper, in the second paragraph, I would substitute the following modified directions: Place the flask under the hydrant, till the solution is perfectly cold ; then add, gradually, strong ammonia, with constant stirring, till the solution is changed into a pasty mass and the ammonia is in slight excess; then add cautiously HNO3 (1.40 specific gravity)

Jan 1, 1885

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By R. W. Coughlin, W. U. Ault

Experiments in laboratory and mine have clearly demonstrated the usefulness of radioactivity detection for directly measuring the potassium content of potash ore as mined. This paper presents the results of these tests and documents the design of a system for automatically grading and sorting potash ore on the basis of radiation detection. It is shown how the experimental results in the subject mine lead directly to the design of this kind of an automatic control system. The system is capable of grading the ore with an accuracy of approximately ±2% K20 content or better. Due to the usual stratification of the ore body, mining potash seldom presents an extreme problem of gangue separation. Nevertheless, it is frequently necessary to transport within a potash mine and even hoist to the surface considerable quantities of halite and other valueless materials. Up to recent times it has been customary to recognize and route these materials by simple visual and manual techniques. However, the work reported here clearly demonstrates that it is now practical and economical to improve upon these techniques by continuous measurement1 of the naturally occurring radioactive isotope, potassium-40. It was the purpose of the work reported here to investigate this technique and assess its applicability. LOCALE OF EXPERIMENTS The work described here was carried out in a potash mine in Carlsbad, N.M. At the working face of this mine the potash ore is freed by blasting; it is then transported a short distance by shuttle car to a moving-belt system which conveys it to the main shaft where it is hoisted to the surface. Quantities of gangue which are also produced in the mining operation are disposed of in mined-out sections of the mine where possible. Otherwise, this material which contains only a small percentage of potassium (as K2O) must also be transported by the conveyor-belt system to the main shaft and then hoisted to the surface and discarded. With this situation, any measuring device for automatic control purposes must be capable of clearly distinguishing between gangue containing insignificant amounts of K2O and ore containing larger percentages of the same mineral. The conveyor-belt system transports the material from the mine face to a rotary crusher and then to temporary storage pits at the main shaft. This is shown in Fig. 1. Upon leaving the conveyor belt the material enters either one of the two storage pits according to the position of a manually operated gate. It was decided that all experiments should be carried out at the conveyor belt between the crusher and gate with a view to the possibility of providing a signal which could operate the gate automatically. THEORETICAL BASIS AND LABORATORY EXPERIMENTS In principle it is possible to grade potassium-bearing ore on the basis of radioactivity. Natural potassium contains 0.012% K40, which is radioactive with a half-life of 1.3 x 10' years. Although about 89% of the K40 disintegrates to Ca40 by beta decay, the other 11% changes to Ar40 by electron capture and the emission of gamma rays. Unlike the ß-rays which are readily absorbed in the first few millimeters of ore surrounding the disintegrating nucleus, the y-ray photons will escape from an ore sample several inches in size. A detector rigidly mounted under a conveyor belt loaded with potash ore will intercept some constant fraction of all the photons emitted from the ore within its field of view. Under these

Jan 1, 1968

By N. C. Fick, R. L. Rickett

DESPITE the large volume of literature on alloys of iron and silicon,1 there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carbon and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in, sheet and strip form, the constitution was determined of a series of commercial silicon steels containing 0.05 to o.08 per cent carbon and 0.20 to 4.31 per cent silicon, over the temperature range 1300° to 2500°F. These alloys were all from regular production heats and of commercial quality. The results of, the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented. MATERIAL AND PROCEDURE All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness-the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. [ ] The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired. range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1946

By R. L. Rickett, N. C. Fick

Despite the large volume of literature on alloys of iron and silicon,' there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carl~on and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in sheet and strip form, the constitution nas determined of a series of commercial silicon steels containing 0.05 to 0.08 per cent carbon and 0.20 to 4.1 per cent silicon, over the temperature range 1300° to 1500°F. These alloys were all from regular production heats and of commercial quality. The results of the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented Material and Procedure All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness—the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1947

By N. C. Fick, R. L. Rickett

Despite the large volume of literature on alloys of iron and silicon,' there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carl~on and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in sheet and strip form, the constitution nas determined of a series of commercial silicon steels containing 0.05 to 0.08 per cent carbon and 0.20 to 4.1 per cent silicon, over the temperature range 1300° to 1500°F. These alloys were all from regular production heats and of commercial quality. The results of the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented Material and Procedure All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness—the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1947

By P. Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occurring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, Calif. recovers potash from natural brines, but uses fuel to accomplish evaporation. Solar evaporation is always desirable, because of low costs, however artificial evaporation may be economical if a group of very valuable salts are recovered. This is the case for the American Potash operations at Trona. Solar evaporation is limited by low working temperatures, which in most areas of the world is between 18 and 45°C. In many cases the average working temperature is about 25°C. However, solar evaporation will have to accommodate itself to the highs and lows of each 24 hour period, and to the different average temperatures during the months of the year. Therefore, solar evaporation, although more economical than artificial evaporation, has a tem- perature limit which greatly reduces the chances of its application. The feasibility of solar evaporation as a means of recovery of values from a particular brine, may be evaluated by the use of phase diagrams showing the several components present. This paper is restricted to the five component system: C1-, SO4=, Na+, K+, Mg++, and H2O, which correspond to brines found at Wendover, Utah, the Great Salt Lake, and sea water bitterns. THE BONNEVILLE OPERATION AT WENDOVER, UTAH For more than 25 years Bonneville, Ltd., now a division of Standard Magnesium and Chemical Co. (recently acquired by Kaiser Aluminum and Chemical Corp.), has been recovering potassium chloride from the brines found in the desert area just east of Wendover, Utah. Solar evaporation of the brines is possible as a consequence of relatively low precipitations (year average: 4.8 in.), and of dry and hot summer months. The brine, collected by a series of approximately 67 mi. of ditches crossing the desert, is fed into solar evaporation ponds. Evaporation which takes place from around the middle of May to about the end of September, permits the crystallization of approximately 90% of the originally present NaCl on what is called the "General Pond Area". Further evaporation,

Jan 1, 1964

By W. McA. Johnson

THE work of J. E. Johnson, Jr., on the effect of small amounts of oxygen in cast iron in increasing its strength and resistance to shock, is of interest from the technical and scientific standpoints. The following exposition of the theory carries Mr. Johnson's explanation further and, in my opinion, will disclose certain related phenomena and perhaps shed further light on the subject. Some facts, so novel in character as to excite incredulity, have been accepted finally by many metallurgical authorities. One of these is that oxygen to the amount of 0.060 per cent. in cast iron gives it a breaking strength of 3,500 lb. per square inch, compared with a breaking strength 2,500 lb. per square inch in cast iron of the same composition with re-ect to elements other than oxygen, but having only 0.010 per cent. oxygen. The "oxygenated" cast iron, even if made in a coke furnace, has properties equivalent to the best charcoal pig iron. Mr. Johnson has also established the fact that the variations in combined carbon cannot account for the results. By microphotographic evidence he has shown that in oxygenated cast iron the graphite particles are dense and spherical, while in well-deoxidized cast iron the graphite particles are flaky and leaf-like. It is just a matter of common sense that iron of the latter structure is much weaker than the former. The analytical and microscopical work has been done with care and there is no doubt in my mind about the accuracy of the, experimental results. In this paper then, we shall consider it as accepted that small amounts (0.060 per cent.) of oxygen increase the strength of cast iron by producing a structure in which the round and solid particles of graphite are surrounded firmly by a principal matrix of ferrite. The purpose of this paper is to show that the reason why the graphite particles are round is founded on the fact that the particles of any precipitate are made denser and harder by the presence of a reagent having a solvent action on the precipitate. This can be stated as a law, although I have never seen it so given in any textbook.

Jan 2, 1916

By John A. Church

AT a time when the treatment of gold and silver ore9 by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

By Richard H. Olson, Lawrence A. Roe

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% Si02, 31.89% MgO, and 4.75% H20. However, as an industrial commodity, talc rarely approaches theoretical purity. Nevertheless, the impure talc products of commerce find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are tremolite, chlorite, dolomite, mica, and magnesite. Steatite was originally a mineralogical name applied to pure talc. In today's commerce steatite generally refers to the massive variety of talc suitable for electrical insulator manufacture. Block steatite ore can be machined into various shapes. Impure varieties of massive or block talc are still commonly referred to as soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soapstone and talc, this is a natural thing since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as "slip") have been grouped together and called soapstone or talc. Further, there is a mineralogical relationship of pyrophyllite to montmorillonite and talc to hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Indians on Santa Catalina Island, CA. In the mid-1800s, soapstone from deposits along the western foothills of the Sierra Nevada mountains was used by white settlers for building and ornamental stone and in the linings and foundations of furnaces (Anon. 1956). Previous to 1916, the annual recorded production in California did not exceed 2000 tons. In the period 1912 to 1918, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 9,000 to 20,000 tons. In the mid-1930s, the use of talc in wall tile grew rapidly. In California, the production of talc grew to 63,000 stpy in 1943. The post-war building boom helped California production to grow to 120,000 tons in 1951. In 1968, production was 165,000 tons, 1969 was 145,000 tons, 1970 was 185,000 tons, and 1972 was 155,000 tons. Talc mining in New York state dates to about 1878 when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville, New York. In 1893, this operation was sold to the International Pulp Co. which changed its name to the International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc. in 1974. A new talc operation, the Gouverneur Talc Co. owned by the R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 200 stpd (Gillingham, 1950). Subsequent expansions have increased capacity to over 600 stpd. The Vermont talc industry began just after the start of the 20th century. Talc was discovered in the area of the present Johnson, VT, talc mine in 1902. The American Minerals Co. initiated plant operations at Johnson in 1904. The Magnesia Talc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963; Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine has a long history as a producer of talc crayons. The Eastern Magnesia Talc Co. was formed in 1924 by a merger of the Eastern Talc, Co.

Jan 1, 1983

By Paul Beck

WHILE the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room tem-perature is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains are not noticeably elongated in the first place. However, with small deformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell,1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is com-pleted-after the deformed grains have been replaced by new unde-formed grains-the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. elapsed before the deformed samples were ready for examination, and consequently no recrystallization time shorter than 5 min. could be measured.

Jan 1, 1939

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami's reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."' A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. ' J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957