Search Documents

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

By Thomas Leonard Watson

Jan 1, 1906

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By AIME AIME

WHEN "Chief" Buehler in mid-September set out on his official 10,000 mile swing-around-the-circle visiting Local Sections he decided not to tell his audiences how to organize and operate a state geological survey. As the director for 28 years, of the Missouri Bureau of Geology and Mines (which, he concedes, is the best in existence) lie could have done this to good advantage; but he preferred to discuss affairs of the Institute. In 25 speeches made to member and student groups, he dwelt on sonic or all of the following phases of activities. He stressed the vital importance of the Local Sections in providing the opportunity for members to associate under pleasant auspices with others in their profession. The benefits of Institute membership he classified as tangible and intangible. Of the two lie felt that the latter were more important. A man's progress in his profession depends in large measure upon a broad acquaintance and friendship with others. The Institute is incomparably the best medium for meeting fellow engineers. The primary, function of the new enlarged Membership Committee is to obtain a comprehensive list of engineers eligible to be members, always hearing in mind that the standards of membership must not be lowered in any degree. These men are to be invited by individual letter to apply for membership. Whether they become members or not is of less importance; but it is vital that no qualified man should be outside the fold for the reason that membership had never been suggested to him. Dr. Buehler emphasized repeatedly his feeling that the younger man that had never had Institute membership brought specifically to his attention had been cheated:

Jan 1, 1935

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By James K. Richardson

Today, the enigma of the "missing man" in the metal mining industry equals, and frequently surpasses in objective importance, the problems of ore development, drilling, sampling, pumping, milling techniques, geophysical prospecting, or any one of a hundred highly technical subjects. Unfortunately, as engineers, we have confined our attentions, in the main, to the scientific phases of mineral technology, relegating our man power problems to the background. But what good has all our scientific study and preparation been if we can't get the ore mined, milled, or smelted? What has happened to our labor supply? Where is the good old miner who could timber, drill a round, lay track, or do any job underground?

Jan 1, 1949

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased-capacity electric transmissions using either wheel-mounted or axle-mounted traction motors makes a reality of single-axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cu yd and a working weight of nearly 1,500,000 lb. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTROTORQUE control system. Electrotorque is a completely static, solid state electronic system supplying controlled power both to the armatures and to the fields of the d-c shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corp.

Jan 1, 1970

By J. L. W. Birkinbine

INTRODUCTION. This paper is a discussion of a part of the mineral wealth of the States of Oaxaca and Puebla, Mexico. It does not refer to the precious metals, some miles of which, in these States, are said to have been worked before the advent of the Spanish conquistadores in the sixteenth century, as my purpose is to invite attention to the exploration of deposits of coal and iron-ores in the Mixteca region. The prominence given to coal is warranted by the great effect of the scarcity of fuel upon the industrial development of Mexico. Under the progressive administration of President Porfirio Diaz, the Republic has made wonderful advances in the past three decades; and this progress would have been greater but for the limitations imposed by expensive fuel. In the spring of 1906 I was detailed by the Birkinbine Engineering Offices, of Philadelphia, to accompany A. B. Adams, of New York, in a reconnoissance of reported deposits of iron-ores in the State of Oaxaca. The result of this expedition was the formation, in 1907, of the Oaxaca Iron & Coal Co., of which Mr. Adams became, and has remained, President and General Manager, and I have spent the past three years as Chief Engineer of this company in Mexico, principally in western Oaxaca, where field-headquarters were established. GEOGRAPHY AND POPULATION. Although the geographical anti topographical, features of the Republic of Mexico are well known, few realize that the majority. of its population is domiciled in the States which immediately surround the capital city of Mexico, including the Federal District, Mexico, Tlaxcala, Morelos, Puebla,

Sep 1, 1910

By Malcolm T. Hepworth

RECENT interest in thermoelectric devices has been directed toward studies of the properties of thermoelectric materials of semiconducting solid compounds with little attention given to ionic and semiconducting liquids such as aqueous solutions, fused salts, and mattes. One type of thermoelectric system is the thermocell: a nonisothermal galvanic cell with two identical electrodes at different temperatures connected by an electrolyte bridge. An electromotive force, v, is generated which is a function of the electrode reactions and the properties of the electrolyte according to the Eastman' equation: where S* is the entropy change of the system arising from the electrode reactions and by heat transferred by ion migration and by thermal conduction. The quantity nF is the product of equivalents passed and Faraday's constant. A value of S* of 23.06 cal per "C is equivalent to 1 mv-Faraday per "C. The symbol, a, is used for dV/dT in analog to the See-beck coefficient of solid-state thermoelements. de Bethune2 has calculated the temperature coefficients of the electromotive force of a large number of nonisothermal aqueous cells from measurements on the nonisothermal temperature coefficients of the standard hydrogen electrode, combined with data on the isothermal temperature coefficients of half-cells tabulated in the literature. Values of these coefficients (a) in de Bethune's compilation ranged up to 3 mv per C. In particular he reported a value of +2.059 mv per "C at 25'C for the cell: Fe (aqueous, unit activity) (aqueous, unit activity) written for the hot-electrode reaction. The positive sign indicates that the hot electrode is positive (an "n-type thermocell"). In analog to a solid-state p-n system, it would be possible to couple two thermocells together to form a system in which the figure of merit could be calculated by adding the temperature coefficients according to the relationship described by offee:' where a is the Seebeck coefficient in volts per "C, p is the specific resistivity in ohm-cm, and K is the thermal conductivity in watts per cm "C. Even though ionic systems have rather high electrical resistivities compared with semiconducting and metallic systems, it was felt that a preliminary study of one ionic system should be made to establish some basis for evaluating the possibility of a p-n thermocell for energy conversion. Accordingly the Fe", Fe"' system was studied as a possible component for a p-n system. A glass system was constructed consisting of two vertical water-jacketed tubes connected by a horizontal tube, Fig. 1. Platinum-black electrodes 1 cm by 1 cm in dimension were inserted in each vertical tube with thermometers to register the electrode-compartment temperatures. The temperature of the electrode compartments was controlled by circulating water from thermostatted baths around the electrode compartments. The electromotive force of the cell was then read by a potentiometer for zero current as a function of the temperature of the hotter electrode. Current output of the cell for varying external loads was also measured. The cell resistance was measured by means of a bridge circuit with 10,000 cps signal and oscilloscope. Resistance measurements were converted to specific resistivity by calibrating the cell with a solution of known conductivity.

Jan 1, 1965

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By Curtis Wilson

FROM the results of his investigation of the hardenable copper-nickel-silicon and copper-cobalt-silicon alloys, M. G. Corson1 explained the dispersion-hardening effect by assuming the precipitation of the inter-metallic compounds nickel silicide and cobalt silicide, and on this basis he constructed diagrams for the pseudobinary systems copper-nickel silicide and copper-cobalt silicide. A consideration of these diagrams and of the factors that exert such an important influence upon the rate of precipitation, such as degree of supersaturation, nucleus number and rate of diffusion, leads to the expectation that the rate of precipitation of the silicides on reheating the quenched solid solutions at temperatures below the alpha-phase boundary should increase continuously as the reheating temperature is raised. The present investigation shows that while this rate does increase with the reheating temperature in a general way, it does not do so continuously. Supplements to Corson's diagrams are offered, showing the discontinuities, and slight modifications in the solubility curves are suggested.

Jan 1, 1933

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954