Search Documents

The Alligator Ridge Project is owned jointly by Amselco Minerals Inc. and Occidental Minerals, with Amselco being the operator. It is the latest of Nevada' s gold heap leaching operations , having gone into operation in October of 1980 after a design and construction period of only seven and one-half months. Alligator Ridge is located about 77 km (48 miles) northwest of Ely, Nevada. Three separate but adjacent ore bodies will be mined: Vantage I, II and III. The first lies virtually at the surface and is totally oxidized; the second is somewhat deeper and contains some carbonaceous material; and the third is at the lowest horizon and contains substantial carbonaceous ore. The ore is a Carlin- type siltstone which has been silicified, especially at depth, and contains finely disseminated free gold. Exploration drilling on Alligator Ridge resulted in the defining of an ore reserve of about 4.54 million mt (5 million st) averaging 4. 12 g Au per mt (0. 12 oz Au per st). A pilot heap leaching program was run during 1979. Because of the high content of fine material in portions of the ore body, one test heap of 5,000 tons was leached, after being crushed to 19 mm (314 in.), in the conventional manner using cyanide and caustic while a second heap of 2,500 tons of ore was agglomerated with cement before leaching. Results of this work were reported at the 1980 American Mining Congress meeting by Paul Chamberlin (see Bibliography). The test work clearly indicated the superior leaching qualities of the agglomerated ore, and the plant was designed on this basis. Run-of-mine ore is crushed in an open-air crushing plant using a jaw crusher followed by two cone crushers, one standard and one shorthead. Provision was made to bypass the shorthead when the ore is wet from rain or snow. Crushed ore at 19 mm (314 in.) size is mixed with cyanide solution and cement, with the ratio of the latter to the ore being 2 to 5 kg per mt (4 to 10 lb per st). The resulting moisture content is about 870, and the fines are effectively bound to the coarse particles so that migration of the fines in the heap does not take place during leaching. For agglomeration, Amselco uses a rotating drum 2. 75 m 0 by 6 m long (9 ft 6 by 20 ft). For the same agglomeration, Candelaria uses three "grasshopper" conveyors, with introduction of caustic- cyanide solution at the conveyor transfer points. Provision was made for future addition of cement slurry at these same points.

Jan 1, 1981

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By S. R. Goodman, Hsun Hu

The rolling texture transition in copper as a function of deformation temperature is found to be quite similar to that in high-purity silver. The ordinary copper type texture changes gradually to the brass type, accompanied by an increase in the stacking fault frequency, as the temperature of deformation decreases. The rolling textures obtained at low temperatures and the corresponding annealing textures compare remarkably well with the ordinary rolling and annealing textures of low-zinc brasses. Furthermore, it is also found that the observed stacking fault energies of copper specimens deformed at low temperatures correspond closely with those of low-zinc brasses, as deduced from measurements of the dislocation nodes. These results are consistent with the idea that texture transition may be significantly dependent on the stacking fault energy. It was shown in a series of previous publications1"3 that the rolling texture of high-purity silver changes gradually from the common silver type (or the brass type) to the copper type* with increasing temperature *The silver or brass type rolling textures are commonly described as (110)[112],4,5 whereas the copper type rolling textures are mainly (123) [a121 and (146)[211].5 Other ideal orientations have been used by various investigators for the copper type rolling textures, but the actual difference among these ideal orientations is rather small. of deformation, and that such texture transition can be correlated with the change in stacking fault frequency as a function of rolling temperature. Furthermore, it was shown that the formation of annealing textures in high-purity silver from the various rolling textures obtained during the course of texture transition depends entirely upon the deformation texture. From a common silver type or brass type rolling texture (such as produced by rolling at 0" or at 50° C) the recrystallization texture is mainly (120)[211], which is quite different from the recrystallization texture of brass.* However, for both ma- terials the orientation relationship between the rolling texture and the recrystallization texture can be expressed in terms of similar rotations around [Ill.] axes of approximately 30 or 35 deg. They differ in that the [Ill] rotational axes are different. In the case of high-purity silver, the axes of rotation are the two (111) poles near the plane normal of the deformed specimen with a (11l)[112] type rolling texture, whereas in brass, they are the (111) poles near the direction of rolling. For high-purity silver with a predominantly copper type rolling texture (such as produced by rolling at 150° or 200°C) the recrystallization texture is mainly (100)[001], or the cube texture, plus its twin orientations. It was shown previously6 that such reorientation observed in copper or aluminum can be described as [Ill] rotations of 30 to 40 deg. For intermediate cases, i.e., when the rolling textures are composed of a

Jan 1, 1963

By J. L. Perry

FOR many years, you and your fellow members of the American Institute of Mining and Metallurgical Engineers have devotedly and ably applied yourselves to the art of making iron and steel. having foremost in your minds the conservation of raw materials, suitable and efficient facilities, economical processes, and improved quality of product. For the past three strenuous years you have contributed wholeheartedly to meeting the problems of increased production. You have conducted scientific and technical investigations and research, recommended experiments. and gathered all the available and valuable information possible to gain the desired objectives. You have had many obstacles and difficulties to overcome. In the early days of your organization, there was some lack of co-operation from the industry itself-perhaps, for example, some failure to recognize the mutual advantages of free exchange of experiences and information. But regardless of any hindrances, you have made many and valuable contribution which have tended to make iron and steel manufacture leas of an art and more of a science.

Jan 1, 1944

By J. Parke Channing

WE are accustomed to think that we are efficient in the United States, particularly with respect to such things as mining and manufacturing. The conduct of the war has demanded in England and in France a complete readjustment of manufacturing methods and plans, and today England is probably as efficient a country as there is in the world, not even excepting Germany. This is all the more remarkable because it has been notorious for years that England has been inefficient in her manufacturing and the country has been flooded with things "Made in Germany." Today England is almost a socialistic community and the State is doing almost everything. England is now in such a position that practically everyone in the country is engaged in industry necessary for the conduct of the war, and this has been accomplished by increasing the efficiency both of her tools and of her man power. In the United States we certainly have been efficient so far as machines and perhaps so far as methods have been concerned, but we have not been efficient iii the utilization of our man power. Before the war, our labor was undoubtedly far more efficient than that of England, but it certainly was not so highly efficient as it should have been, and the problem that confronts us today, and will all the more confront us after the war, is to make our man power efficient. England has had a taste of what you may call State Socialism, and her laboring men are not going to be content to return to the old order of things. There is one feature of the labor problem in England which has permitted her to reach this condition of state socialism with comparative rapidity; this is that practically all of her laborers are English; she has little or no foreign population. While an Englishman may he a strong union man and ready to fight his employer tooth and nail, at heart he is still a British subject, and when his country was in danger he rose to the occasion.

Jan 5, 1918

By A. M. Gow

The trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling. Mechanics and Theory of Ball Milling As early as 1904, Herman Fischerl reported observations on specially constructed ball mills which allowed the paths of balls to be studied. The following conclusions were drawn: 1. Balls do not grind the ore, but crush it by impact. 2. At slow speeds the balls roll down the inclined heap, but at higher speeds the balls close to the wall adhere to it until they reach a certain height, whence they are thrown through an arc to the bottom. 3. The falling balls do not come down in clusters, but in series, the balls of each row keeping to their own line of flight according to their distances from the wall while ascending. 4. A further increase in speed results in the balls adhering during the whole of the circuit to the side of the drum. (This centrifuging speed may be called the "critical" speed and may be taken as a reference basis, since it is a constant function of the diameter.)2

Jan 1, 1930

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By R. A. Ritter, J. P. Batycky

A numerical technique has been developed to permit estimating the pressure gradient associated with laminar flow of thixotropic liquids through long Pipelines. For this purpose the pipeline is divided into a number of radial and longitudinal increments within which rheological properties of the fluid may be considered as constant at any time. Then, provided only that the fluid flow curve is defined at every duration of shear, it is possible to predict the instantaneous pressure gradient at any cross-section along the pipeline for each desired flow rate and pipe size. The technique consists of an iterative integration of shear rate to establish the appropriate value of the wall shear stress at each location. Consistency of fluid in the increment is determined by the flow history of that increment, while the radial flow associated with variations in velocity profile is accounted for by adjusting the width and radial position of the increment. A number of pressure profiles, computed at each of several flow rates, provide a convenient basis for pipeline design and pump selection. INTRODUCTION In recent years considerable attention has been given to predicting pressure drop associated with the isothermal laminar flow of time-independent non-Newtonian fluids in pipes and annuli. 6,11,12 The approach generally has been to develop analytical relationships between flow rate and pressure drop based on simple constitutive models which hopefully provide an approximate description of the rheological properties of the fluid. Analytical solutions are highly desirable since the influence of all pertinent parameters can be readily determined. Unfortunately, however, this approach is restricted to simple flow geometries and- frequently leads to erroneous results due to inadequacies in the model. In certain cases a solution may be obtained through applying appropriate numerical techniques.l,14 For example, a digital computer program is available for predicting the velocity profile and pressure drop encountered by any Newtonian or time-independent non-Newtonian fluid flowing under laminar conditions in a cylindrical pipe or annulus.l In this paper the consistency behavior of the fluid need only be described in terms of basic rheological data. Analyzing flow systems involving fluids with time-dependent rheological characteristics is considerably more complicated since substantial changes in consistency may occur because of sustained shear action. This sensitivity to shear frequently persists for several hours. Consequently, variations in pressure drop and/or flow rate resulting from the aging process and addition of unsheared or partially sheared fluid to the system must be considered for purposes of pipeline design. This paper outlines a numerical method for predicting the transient and steady-state laminar flow behavior of a thixotropic liquid in a pipeline of arbitrary length (i.e., at a specified constant flow rate, the instantaneous pressure gradient may be determined at any time after start up and at any location along the pipeline). Several such pressure gradient profiles, computed at several flow rates, may be combined to produce a complete portrait of the system response. This flow portrait provides a reasonable basis for pipeline design and for selecting a suitable pump characteristic. TIME-DEPENDENT RHEOLOGICAL BEHAVIOR The most familiar time-dependent rheological properties are those exhibited by thixotropic liquids. Many of these materials, particularly thixotropic crude oils, generally display an apparent yield stress in that a finite pressure gradient is required to initiate flow. Then, under the influence of sustained shear at a constant shear rate, the consistency systematically decreases to some final limiting value. The shear stress obtained at

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By F. W. Denton

Much has been written about the possibilities of the Vermilion and Mesabi ranges of northern Minnesota as producers of large quantities of high-grade iron-ore. The Mesabi range in particular has attracted considerable attention on account of the proximity of the ore-deposits to the surface, which has been as-

Jan 1, 1898

By D. A. Dahlstrom

Although the liquid-solid cyclone is a relatively recent innovation in the field of coal preparation, various authors have already indicated three distinct applications to operations encountered in the modern tipple. Driessen's articles and work at the Dutch State Mines exhibited its possibilities in the beneficiation of fine coal with apparently high efficiencies down to the 200-mesh fraction. 1 2 3 4 Other publications point out its use as a recoverer, thickener, and preliminary dewatering agent of fine coal which in too many cases is being wasted due largely to former high operating cost limitations 5 6. Finally, certain authors have emphasized the practicability of applying the cyclone to the elimination of coarse and fine solids from water slurries in the tipple in order to produce a water suitable for recycle purposes containing only minute particles far below the 200-mesh size.6 This would result in a closed water system for many cases, with its accompanying economic and operating advantages to locations where water quantity and quality problems are severe; better operation of washing equipment using a consistent water devoid of injurious fine particles; lowered maintenance costs due to the lesser abrasion resulting when the fine abraiding particles are removed; and the greater ease of disposing of refuse streams of reduced volume containing greater percentages of solids.

Jan 1, 1949

By John A. Church

IT is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of. the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By W. H. Yarroll

This paper presents a general discussion of the utility of the statistical technique known as multiple correlation, and gives three specific examples of its application. The first demonstrates the most simple form, or straight-line, multiple correlation. The other two demonstrate multiple correlation analysis in best-fitting third-degree parabolas. With the increasing availability of digital computers, the method becomes entirely feasible where heretofore its use was impractical. The advantages of the method are discussed, and curves are presented which were developed by computerizing the regression equations developed in the examples. The method described in this paper is for use with complex systems, and the examples given are complex metallurgical systems. This subject falls under the general classification of cybernetics, which is defined' as "the science of control and communication, in the animal and the machine." Machine, in this case, can include chemical and physical processes which take place within machines and processing equipment of all kinds. The classical approach to scientific investigation has been the construction of simple models and the changing of variables one at a time. This method is wholly inadequate for obtaining useful information from the complex systems of modern technology including many of our flotation and hydrometallurgical processes. Cybernetics offers the method by which complex systems which have been implemented as an art in the past can now be analyzed with all the discipline of a science. Mathematical techniques for achieving multiple correlation analysis have decided advantages over some of the other statistical methods.2-4 Multiple correlation does not require a series of experiments that have been rigidly planned as do many of the other statistical methods. For this reason, it can be used effectively for interpretation of information from op- erating plants, where planned experiments are impractical, as well as for laboratory experiments. First-degree multiple correlation has been used for many years, and was useful, but limited to linear or nearly linear relationships. The technique described in this paper provides a method for analyzing systems which may be non-linear. This particular technique is multiple correlation analysis in best-fitting third-degree parabolas. It is quite possible that lack of reference to the technique has been due to the overwhelming mass of computations it requires even for relatively simple problems. With the advent of computers, however, its use has become entirely feasible. For the benefit of those who may not be familiar with the subject, it might be well to pause at this point to discuss multiple correlation analysis — what it is and what it achieves. To go back to the old familiar fitting of a set of points with a best-fitting straight line by the least squares procedure, it is conceded that this a good method where there is only one independent variable influencing the dependent variable under consideration, and providing that the relationship is linear. In most fields of investigation, however, there are usually a number of factors exerting important influence, and they frequently bear relationships with the dependent variable other than straight line. Under these conditions, it is easy to see how misleading a simple correlation study might be. Multiple correlation can be used for any number of variables. Within the experience of the writer, this technique has been used to establish regression equations for determination of carbon rate, burden permeability, and production rate on iron blast furnaces, production rate on open hearth steel furnaces, life of molds for steel ingots, rolled steel tensile strength and various defects in rolled products, the performance of ore dressing equipment, and optimization of extractive metallurgical process variables. The discovery of mathematical correlation does not prove, per se, true cause-and-effect relationship, but simply establishes a hypothesis. If the regression equation can be used to make successful predictions of what will happen with future arrays of independent variables, then one can feel reasonably assured that true cause-and-effect relationships have been discovered.

Jan 1, 1968

By R. V. Ramani, G. W. Luxbacher

Computer simulation of mine ventilation system is rapidly becoming an essential tool in mine planning and design. This Paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve primarily for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1980

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947