Search Documents

By W. M. Clark

OUR interest in the matter of pyrometers and pyrometry is primarily that of a user of considerable quantities of heat-measuring equipment; and while we play be somewhat critical on the subject we have aimed to make the nature of these comments constructive. The glass industry in America dates back to 1609, when Capt. John Smith started a small glass plant near Jamestown, Va., with a few Italian workmen, to manufacture glass beads for trading with the Indians. While the industry has expanded until it has reached a volume of over $200,000,000 per annum, the means of heat determination in Colonial days was the human eye, and in much of the industry the same means is used today. About 15 yr. ago the largest glass-house supply dealers began to sell platinum pyrometers, but as nearly all of these proved un-satisfactory, pyrometers met a temporary rebuff from the old-time glass manufacturers. As their ruggedness of construction, reliability, and stability have been improved, however, pyrometers have gradually won their way into more and more extensive use throughout the glass trade. But there are still many applications where pyrometers are not used, largely because of cost and upkeep considerations. There are two distinct fields in glass works for pyrometry. The first calls for accurate temperature measurement and the second only demands knowledge of relative comparative fluctuations of temperature, to know whether the work is becoming hotter or colder. For example, in a lehr for annealing glassware and removing strain we want accurate temperatures to know that the ware is heated to the critical temperature for rapid removal of strain. On the other hand, in a glass pot furnace nearly 120 ft. (36 m.) in circumference, where the pyrometer couples only project inside the furnace wall for less than 2 in. (50 mm.), it is inconceivable that these few inches represent the accurate temperature at every point of the 120-ft. circumference but the relative readings as to whether the pyrometer shows schedule temperature fluctuations are valuable indications for control. The glass melting in the pots is,

Jan 8, 1919

Dec. 2, American Mining Congress, annual membership meeting, University Club, New York. Dec. 2, Society for Applied Spectroscopy, Socony-Vacuum Training Center, New York City. Dec. 4-6, AIME, Electric Steel Furnace Conference, Hotel William Penn, Pittsburgh. Dee. 5, Atlanta Meeting of Southeast Section, AIME, Ansley Hotel, Atlanta. Dec. 7-10, American Institute of Chemical Engineers, annual meeting, Hotels Cleveland and Carter, Cleveland. Dec. 8, AIME, Arizona Section, all-day meeting, Tucson. Jan. 6, 1953, Society for Applied Spectroscopy, Socony-Vacuum Training Center, New- York City. Jan. 14, 1953, AIME Connecticut Section, Hammond Metallurgical Laboratory, Yale University, New Haven, Conn. Jan. 14-16, 19th Annual Meeting of Society of Photogrammetry, Shoreham Hotel, Washington, D. C.

Jan 1, 1952

By A. Vifian, I. lwasaki

Several samples of copper-nickel ore from the Duluth Gabbro were studied to relate their mineral-ogical characteristics with their amenability to concentration by flotation. The most common rocks in the samples were norites, gabbros, and troctolites. The texture of the rocks varied from coarse pegma-titic to very fine. The copper contents ranged from 0.2-0.7% and the nickel contents from 0.07-0.15%. The ore minerals were chalcopyrite, cubanite, pyrrhotite, and pentlandite. Most of the ore minerals occurred in interstices between laths of plagioclase, but some were included in the gangue grains. The samples responded readily to xanthate flotation. After a 65 to 100-mesh grind about 95% of the copper and 85% of the nickel were recovered in a bulk sulfide concentrate. Such recoveries remained constant even with grinds as fine as 270 mesh due to the extremely fine inclusions of sulfides in the silicate gangue. A finer grind than 270 mesh was necessary to free the copper-iron sulfides from the nickel-iron sulfides. A combination of time and British gum* was quite effective in producing concentrates analyzing 25-30% copper. The nickel concentrate averaged 1.5% nickel. Most of the nickel lost in the tailing was present as un-liberated sulfides and not as nickel in the olivine structure. The nickel content of the olivine was only about 0.05 or 0.08%. Western world nickel usage in 1967 is expected to be the second highest on record, amounting to 825 million lb. Despite a rise in mine production, however, demand is expected to exceed supply in 1968. ' Hence, exploration, development, and production expansion projects are being accelerated on a world scale. In Minnesota the copper-nickel bearing Duluth Gabbro is receiving much attention. During the past year 11 companies have been granted leases in the region, and the 1967 Minnesota legislature enacted a tax law designed to encourage the development of a copper-nickel industry. Although it is only during the past few years that mining companies have shown an active interest in the Minnesota copper-nickel deposit, copper-nickel minerals have been known to exist in northeastern Minnesota since 1899.3 At the 28th Mining Symposium, Dr. P. K. Sims, from the Geological Survey of Minnesota, gave a review of copper-nickel exploration in northeastern Minnesota,4 in which he emphasized that the potential of the Duluth Gabbro complex is large. Tests on samples from the Kawishiwi River area were reported by the United States Bureau of Mines in 1955.' In 1964, the Mines Experiment Station described tests on samples from the Gunflint Trail: and in 1966 the Minnesota Geological Survey published a geological map of the Gabbro Lake Quadrangle. The Mines Experiment Station published a study of the concentration of a Minnesota copper-nickel ore in 1967.7 The present paper is divided into three parts. The first describes the mineralogy of some rock samples from the Kawishiwi River area of northeastern Minnesota; the second summarizes the results of numerous flotation tests that were made on the samples, and the third explains the loss of nickel in the flotation tailing. MINERALOGY OF KAWlSHlWl ROCKS Recently five samples of mineralized gabbro from the Kawishiwi River area, a few miles east of Ely, were received at the Mines Experiment Station. One of the samples was a 175-lb composite, which was designated Ore 1556. The other four samples were 7-lb grab samples that had been obtained from four different exploration pits. They were designated Ore 1626, Lots 1 through 4. Basic Mineralogy: Many authors have reported that the rocks of the so-called gabbro of the Duluth Intrusion vary widely in composition.8-9 The samples on which our studies were based also contained a wide range of rocks. A gabbro, olivine-gabbro, anorthosite-gabbro, norite, and a troctolite were represented. The essential minerals in the samples were plagio-clase, pyroxene, and olivine, in variable proportions.

Jan 1, 1969

By H. H. Podgurski, Hsun Hu

Large cryslals of high-purily iron (99.996+ pcl) cannot be obtained by the usual strain-ameal technique. Repealed phase transformation by thermal cycling prior to crilical deformation improves the capabilily of cryslal growith but fails to yield satisfactory crystals. Imperfect columnar crystals can be produced by the phase-transition method. The addition of a small amounl (0.005 wl pet) of nilrogen IT was reported'-4 that for metals of very high purity the usual procedures of the strain-anneal technique fail to produce large crystals. This was eliminates practically all the difficulties in crystal growth by the normal strain-anneal procedures. An actual example is presented, showing that most parts of a strip have been converted into a large crystal by this method. The addition of nitrogen, which can be removed from iron with less difficulty, is believed to be more desirable than carbon additions for the same purpose. thought to be due to the strong tendency for recovery in the high-purity metals: hence the critically strained matrix undergoes polygonization instead of recrystallization upon annealing for crystal growth. Talbot1,2 succeeded in overcoming this difficulty by adding 0.03 to 0.04 pct C to high-purity iron before critical deformation. followed by annealing in hydro-

Jan 1, 1965

By H. Tabachnick, N. Hedley

The extraction of gold and silver from ores with alkaline cyanide solutions is well known. Cyanide solutions are also good solvents for many base metal minerals, particularly most of the copper minerals. Leaver and Woolf,1 who determined the solubilities of copper minerals in 0.10 pct sodium cyanide solution, showed that malachite, cuprite, chalcocite, and bornite are readily soluble in cyanide; least soluble are chalcopyrite and chrysocolla. The Mining Chemicals Laboratory of American Cyanamid Co. has studied the possibilities of using cyanide solutions for leaching base metals. In this article the authors present the results of their experiments with cyanide leaching to reduce the copper content of a zinc concentrate from 0.050 pct to the desired specification of less than 0.02 pct. Zinc Ore Sample: The sample of commercial zinc ore used in this investigation to produce zinc concentrates was ball mill feed ranging from 1/2 in. to fines. The ore was crushed to —10 mesh and riffled into 600-g charges for zinc flotation. Analysis revealed 4.54 pct Zn and 0.005 pct Cu. Examined microscopically, the ore consisted essentially of cream-colored sphalerite and carbonate gangue. It contained a small amount of pyrite, partly tarnished. The only copper mineral identified was chalcopyrite, mostly smaller than 20µ, some of which occurred as attachments on sphalerite. Flotation Procedure: Batches of zinc concentrates were made as required according to the following general procedure. A 600-g charge of —10 mesh ore was ground for 4 min at 60 pct solids in a laboratory steel rod mill. Screen sizing showed it to be all —35 mesh with 42 pct —200 mesh. The pulp was transferred to a Fagergren laboratory flotation machine, diluted to 25 pct solids and conditioned for 5 min with 0.6 lb per ton CuSO4, . -5H2O. It was then conditioned with 0.10 lb per ton Sodium Aerofloat promoter and floated for 5 min with pine oil as frother and creosote as froth stiff-ener. The pH during flotation was 8.5. A typical analysis of zinc concentrate subjected to leaching is 44.41 pct Zn and 0.051 pct Cu. The ratio of concentration was close to 10 to 1. Leaching Procedure: Aero Brand cyanide, technical calcium cyanide analyzing 49.5 pet NaCN equivalent, was used for all cyanide leaching tests. For each test three rougher concentrates floated as described were combined (total weight close to 180 g) and the water content adjusted to 150 ml. The percent solids in the pulp was thus 55. After a weighed amount of cyanide flakes had been added, the pulp was agitated on rolls for a given period, then filtered and washed. Filtrate and washed concentrate were assayed for copper content. The procedure for ammonia leaching was similar to the cyanide process. A series of tests was run in which the effects of ammonia as a solvent for copper in the zinc rougher concentrate were investigated. In each test 180 g of zinc rougher concentrate was leached with 150 ml of ammonia solution. Various strengths of ammonia and times of leaching were investigated. The results are shown in Table I. It is apparent that ammonia was a poor solvent for copper in the zinc concentrate; 60 min of agitation with a relatively strong NH:, solution extracted only 2 pct of the copper. CYANIDE LEACHING TESTS Effect of Solution Strength: The solvent effects of 0.125, 0.187, and 0.250 pct NaCN equivalent solutions were compared for leaching periods of 15 min. Residue and filtrate were assayed for copper content. The copper content of the filtrate plus wash was calculated back to the original volume of cyanide solution (150 ml). The effects of cyanide strength are given in Table II, It will be noted that 15 min leaching with 0.25 pct NaCN equivalent solution extracted 74.6 pct of the copper in the zinc concentrate. The leached product assayed 0.013 pct Cu, appreciably below the required specification of 0.020 pct. Effect of Leaching Time: Portions of zinc concentrate were leached with 0.25 pct NaCN equivalent

Jan 1, 1961

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By d&apos, K. Mukherjee, C. R. Antonio, R. J. Maciag, G. J. Fischer

Tensile data indicate that over the range of strain rates 10-5 to 10-1 sec-1 and in the temperature range 298° to 743°K the flow stress at a given temperature may be expressed as: C0 = Cem where m changes abruptly at a critical strain rate of 10-2 sec-1. The Zener-Hollomon parameter was tested and found to be invalid except at temperatures exceeding 700° K. Values of AH calculated for temperatures above 700°K ranged from 30 to 47.5 kcal per g-mole. ThE flow characteristics of aluminum and aluminum alloys as a function of temperature and strain rate have been of interest to various experimenters for many years. Trozera et al.1 determined tensile flow curves for pure aluminum and concluded that the combined effect of temperature and strain rate on the flow stress could be related using the Zener-Hollomon parameter. More recently, Hockett2 proposed a relationship between compressive flow stress, temperature, and true strain rate which could be represented by a surface. Holt et al.3 studied strain rate effects on flow stress in a number of aluminum alloys at room temperature. It was determined that there is a critical strain rate above which a strain rate effect is observed. It was also reported that the strain rate sensitivity was significant in aluminum alloys in the "0" condition only. In a recent review paper McQueen4 has considered a number of mathematical expressions which have been used to describe the relationship between stress, strain rate, and temperature. These expressions have been applied to the flow characteristics of a number of different metals and alloys including aluminum. In the present work the strain rate sensitivity of 7075-0 aluminum was determined in the temperature range of 298° to 743°K. The tensile flow stress at 0.2 pct offset was obtained over a nominal strain rate range of 10-5 to 10-1 sec-1. EXPERIMENTAL Threaded tensile specimens were cut from a single heat of 7075-T6 aluminum. The composition of this heat is given in Table I. The test bars had a gage section 1.5 in. long by 0.250 in. diam and conformed to ASTM specification E-8-57T. After machining, the bars were annealed at 413° ± 10°C for 2 hr. They were then cooled to 260°C in 3 hr, and finally air cooled to room temperature. This treatment is commonly used to produce the "0" condition. Load-time curves at constant crosshead speeds were obtained at various temperatures using an Instron testing machine. Crosshead speeds ranged from 0.002 to 40 in. per min. A three-zone resistance tube furnace was used for the elevated-temperature tests. Temperatures were measured at three points along the gage length by means of suitably placed thermocouples. Each tensile bar was held at temperature for 30 min prior to testing and the maximum temperature variation along the gage length was kept below 1°C. In all, 275 samples were tested and each data point plotted is an average of at least two tests. In many cases the point represents up to six tests. RESULTS AND DISCUSSION Values of the flow stress at 0.2 pct offset at six different temperatures are plotted vs strain rate on log-log coordinates in Fig. 1. Over discrete ranges of strain rate, the data for each temperature fit the expression:

Jan 1, 1969

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By J. R. Cooper, A. Bruynesteyn

The final results of the operation of the Cananea test dumps are discussed. Scale-up factors between shake-flask tests, column tests and the large test dumps are established for the Cananea ore. The formation of clay layers, which formed inside the dumps and markedly affected extraction, as well as secondary enrichment, are discussed.

Jan 1, 1974

Prof. Frank H. Probert, dean of the College of Mining of the University of California, visited the mining areas in the devastated regions as a member of the Bureau of Mines committee, which is studying the problems presented in the rehabilitation of mines there. He says that the absolute destruction of the coal mines in the Pas de Calais section makes it-necessary to use either the Westphalia or the Saar valley coal. The Saar mines, however, produce a poor quality of coking coal: therefore, it will not be possible to operate blast furnaces very efficiently unless provision is made for the introduction of better coal. He believes

Jan 6, 1919

Robert Schorr, San Francisco, Cal. (communication to the Secretary*):—In operatioils requiring the expenditure of fuel, it is solely a question of supplying a certain number of heat-units at certain temperature-conditions. The difficulty of controlling these temperature-conditions is mainly responsible for low efficiency, unless utilizable waste heat is carefully applied either for the pre-heating of the air necessary for combustion, or for the heating of the raw materials, or in other departments of the works to generate steam, etc. A high theoretical or thermal efficiency very often does not establish a high " commercial" efficieiicy, and this fact is responsible for apparent crude practice in many arts. Coal is still very cheap in the East, and oil sells in the West for less than anywhere else in the world. Despite these favorable conditions, I believe that the list of references given in E. C. Eckel's book,' and also the contributions of C. Naske,2 will show that Mr. Eldred's statement, that a the study of the phenomena of applied combustion has been neglected," is not justified as far as the burning of cement is concerned. I have investigated the heat-balance of a lirne-kiln ailci the commercial advantage of using generator-gas for calcination. Mr. Eldred proposes to calcine the materials in the present type of rotary kiln, gas-fired with long-flame combustion, and to Pdke the fritted calcines to a special, gas-fired clinkering-kiln, which shall embody heat-regenerators. While his state-

Jan 1, 1911

By Charles W. Merrill

IF we follow the threads of the mining problems, upon which I have touched, we find them all leading to one great fundamental desideratum. The people of this State, of this Nation, and of this world must be brought to a better understanding of the basic nature of our industry-must be made more mineral-minded. It is my belief 'that there is not a man present among this earnest gathering of those interested in the mining industry, who has not a deep-seated and heartfelt desire that the existing unprecedented welfare and prosperity of the whole mass of American people be maintained not merely through our own generation but through the generations of our children and their children. In the decades to come there can be no question of the keenness of the foreign competition which we are doomed to meet, and in this great international contest that Nation which has the best balanced program of development and that broadness of vision in its governmental direction, which recognizes the necessity of a sympathetic attitude toward the upbuilding of such a broad pro- gram will be the Nation which will maintain and pre- serve that welfare of all of its people.

Jan 1, 1929

By Edward Skewes

In view of the importance of the Cripple Creek district, the large amount of the publications concerning it, and the circumstance that many members of the Institute reside in it, or are familiar with it through repeated visits, it is surprising that our Transactions should have remained so long without any contributions on the subject. The same observations may be made with regard to the Witwatersrand, in South Africa, the other great productive gold-field of recent development. And I suppose the explanation is the same in both cases, namely, that the members of the Institute persoilally acquainted with the

Jan 1, 1897

By Fred W. Gordon

Apart from the character of pig-iron to be manufactured, other than that it shall be well reduced and open-grained, the selection of the materials should be such as to produce it at the lowest cost. As a rule, the sources of fuels and limestones are not so extensively varied as those of the ores. Many Eastern furnaces are now using Lake Superior ores, and but recently a part of the supply came from foreign ports. It is, however, of the highest importance that the character of fuels and limestones, as well as ores, should be carefully considered in determining their value and making judicious selection among those available. The formulas here offered are based upon the assumption that the heat-requirements for a given mixture are measured by a constant required by the oxide of iron, added to that required for a unit of slag, multiplied by the weight of that slag per unit of iron. The heat-requirements for oxide of iron per unit of pig-iron made are assumed to be 2854 centigrade units. This is taken from the careful analysis of Sir Lowthian Bell, and, so far as the writer is able to determine, is very nearly correct. Dividing this by the quantity of heat that may be evolved and utilized within the furnace per unit of carbon, determines the quantity of carbon required per unit of pigiron ; and if to this be added the quantity of carbon absorbed by the pig-iron, the total requirements in carbon are determined, on the assumption that pure oxide of iron is reduced with pure carbon by the ordinary process of the blast-furnace. Calculating the quantity of slag that would be made from a given mixture of ores, smelted with a given impure fuel and fluxed with a given impure limestone, multiplying this weight of slag by the heat-requirements of its unit (taken at 1050 C. H. U.), and dividing the product by the heat-units evolved and utilized within the furnace per unit of carbon, will determine the quantity of carbon required per unit of pig-iron for the slag.

Jan 1, 1893

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

By W. G. Sinclair

The wartime momentum of exploration continued throughout the year 1945 despite the end of hostilities in mid-August. The table below illustrates drilling activity in the various categories: Completed wells. . . . . . . . . . . . . . . . . . . . . . . . 401 Wildcats.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Wildcat discoveries, oil.. . . . . . . . . . . . . . . . . . . 2 Wildcat discoveries, gas-condensate.. . . . . . . 4 Development wells.. . . . . . . . . . . . . . . . . . . . . .297

Jan 1, 1946

By M. D. Everell

A study has been made of the relationships between grinding selection functions and physical properties of rocks, particularly the failure loads of irregular particles and the compressive and tensile strengths of large regular specimens. The rocks used were limestones of various structures and impurity contents, a carbonatite, and a high-purity crystallized calcite. The selection functions were obtained from carefully performed grinding experiments on selected narrow size ranges in various grinding machines-a laboratory batch ball mill, a Hard grove grindability machine, and a mill of the type suggested by Yang, Mempel, and Fuerstenau. The specific rates of breakage during milling and the failure loads of irregular specimens correlated well for the rocks studied. The testing of irregular particles is suggested as a means of predicting the behavior of commercial mills.

Jan 1, 1973

By Dudley Homer

MINAS DE MATAHAMBRE, S.A. is a Cuban mining corporation with mines located in the Matahambre district about 100 miles westerly from Havana in the Province of Pinar del Rio. The port of entry is the subport of Santa Lucia on the north coast of Cuba. The mines are located six miles inland at the town of Minas de Matahambre. Minas de Matahambre and Santa Lucia are connected by a 9-mile automobile road, and a 30,000-ft. Leschen aerial tramway. At the subport of Santa Lucia the company maintains docks, concentrate bins, tugs, lighters, and miscellaneous shipping equipment. The power plant of the company is also located at Santa Lucia. Connection between the power plant and the mine is effected by a 30,000-ft. transmission line. In the town of Minas de Matahambre are located the mines, concentrator, shops, and warehouses. The con-centrates are transported to Santa Lucia by the Leschen aerial tramway. The mines are equipped with three shafts, viz., Nos. 1, 2, and 3. (Fig. 1.) No. 1 Shaft is a three-compartment vertical tim-bered shaft and has reached a depth of 1825 ft. This is the present main hoisting shaft. No. 2 Shaft is a four-compartment vertical shaft lined with steel sets and native hardwood lagging. Certain portions where the ground is heavy have been lined with re-inforced concrete. Practically all production will be hoisted eventually through this shaft. No. 3 Shaft is a three-compartment vertical timbered shaft. It has reached a depth of 1090 ft. Its purpose is for prospecting, ventilation, and handling men and sup-plies through the north section of the mine.

Jan 1, 1933