Search Documents

By J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation, sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher. The

Jan 1, 1976

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

CARL A. WENDELL, New York, N. Y. (written discussion*) .-I have never seen in print anything that even remotely has approached this article in clearness and important conclusions in conjunction with work done on the sink-and-float test. I have had many hundreds of these tests made and on different specific gravity solutions and the resultant product analyzed, but I have never grasped nor been able to show what this article sets forth. This article brings out one factor very clearly to my mind; what is to take the place of the solutions of different specific gravities used to obtain the laboratory results, when it comes to washing on a large scale, since water has one constant weight only? The answer is, sizing of coal. And as we know the importance of size versus specific gravity of the material to be washed, perhaps defined (practical) lines can ultimately be gotten up so that the sizing, if any, may be determined at the same time as the laboratory work on the coal is being done. G. R. DELAMATER, ? Steelton, Pa. (written discussion?).-The authors' deductions are well founded and although they disclaim any wide experience in commercial coal washing, practically all of the data presented are applicable to coals of all parts of this country. The paper clearly sets forth the great necessity of careful preliminary investiga-tion of each contemplated washery undertaking and contains the follow-ing very true statements. "It is not safe to assume that any coal which can he successfully washed on coarse coal jigs can be cleaned more com-pletely by washing at a finer size on tables," and "The effect of finer crushing upon the completeness with which impurities may be separated from coal depends upon two opposing tendencies. First, that the more finely a raw coal is crushed, the more completely will the particles of impurities be detached from the particles of clean coal. Second, the finer a coal is crushed the more difficult it becomes to separate the pieces of clean refuse from the pieces of clean coal."

Jan 12, 1919

By A. H. Bell

DEEPEST hole in the earth, and deepest producing oil well in the world-such is well No. K.C.L. A-2, of the Continental. Oil Co., completed on April 12 in the San Joaquin valley about four miles west of Wasco, Calif. It penetrated the earth's crust to a depth of 15,004 ft.- almost three miles-a depth that exceeds by over 2200 ft. that of the previous record holder in western Texas. It is now producing oil from sands at a depth from 13,092 to 13,- 175 ft., which is about 1500 ft. deeper than the record formerly achieved in Louisiana. Continental's new well was bottomed in what is possibly Domengine-Avenal Eocene sand, and is producing from the Middle Miocene equivalent to the Rio Bravo sand.

Jan 1, 1938

By Douglas J. Harvey

The surface tension of lead-tellurium alloys (in the range 0 to 6.70 at. pct Te) ad lead-arsenic alloys (in the range 0 to 10.53 at. pct As) has been examined by the maximum bubble pressure method. The surface tension of high purity lead can be expressed over a range of temperatures (M.P. to 750°C) by the relationship = 512 — 0.133t. Arsenic and lellurium were both found to be surface active in lead. The surface excess concentration at 700°C was .found to be constant at 0.74 x 10-10 moles per sq cm for tellurium. The surface excess of arsenic at 700°C varied between 0.26 x 10-10 moles per sq cm at 0.16 at. pct to 1.5 x 10-10 moles per sq cm at 8.3 at. pet. The surface tension of lead has been investigated sporadically over the last 90 years. The first recorded study was made by Quincke1 who used a rather crude application of the drop-weight method. Hogness2 obtained the first reliable value for the surface tension of lead by measuring the pressure necessary to force the liquid metal from the end of a small capillary of known radius. Hogness gives the empirical formula: ?(surface tension)= 444 - 0.077 (l-327) which describes the relationship between surface tension and temperature ("C); This work was followed by that of Bircumshaw3 who applied the two-capillar maximum bubble pressure method of Sugden.4 The values published by Bircumshaw are in good agreement with those found by Hogness. Matuyama5 examined the surface tension of lead by the drop weight method. However, the values found are somewhat higher than those previously reported. More recent investigations by Greenaway6 and by Melford and oar' have resulted in data which are not in close agreement, but which are well within the expected range at most temperature levels. The study of the surface tension of lead alloys began with Drath and sauerwald8 who examined the lead-bismuth system. They found that the surface tension values of the alloys in this system deviated only slightly from the ideal mixture rule. Matuyarna5 examined the lead-antimony system. Bircumshaw the lead-tin, and the lead-indium system was studied by Hoar and Me1ford.10 The results of these investi- gations are summarized in Fig. 1. It may be seen that the data vary only slightly from the ideal mixture rule. As none of the metals studied and reported in the literature has a very interesting effect on the surface tension of lead,*the next logical step might be to examine the effect of metals of low solubility or nonmetals having some liquid solubility. Baes, and Kellogg11 have pointed out that the elements most likely to be surface active in liquid metals are ones of limited solubility in the liquid state and possessing weak intermolecular bonding forces in the solid state. Therefore, Group V, VI and VII nonmetals are most likely to be surface active. It was decided to examine the effect of a borderline metal, arsenic, and a nonmetal tellurium. Arsenic forms a eutectic with lead having a melting point of 290°C and a composition of 6.9 at. pct As.13 Pure arsenic sublimes when heated above 610°C. Even though alloying with lead lowers the vapor pressure, fumes containing arsenic are evolved at a very noticeable rate when lead-arsenic alloys are heated above 650°C. Tellurium raises the liquidus temperature of lead sharply to 904°C,14 the melting point of PbTe (lead-telluride). The solid solubility of tellurium in lead was determined by Greenwood and worner15 to be 0.0007 at. pct at room temperature. EXPERIMENTAL METHOD Surface Tension Measurement—The two capillary maximum bubble pressure method for measuring surface tension developed by Sugden,4 and used later

Jan 1, 1962

By John B. Knaebel

The annual Jackling Award Lecture, sponsored by the Society of Mining Engineers of AIME, is intended to honor and commemorate one of the greatest mine-makers of all time, an innovator whose vision and determination made ore out of waste rock. He ushered in a new philosophy of mining which revolutionized some segments of the industry and notably affected our economy generally. To have been asked to given the Jackling Lecture this year is an honor that I scarcely deserve, but which I have accepted in humble gratitude. Although it is true that "many a mine has made the man," it is also true that while ore bodies are found, mines are made. That statement has been hammered into my skull many times by a man whose own career exemplifies its truth, a man who has been first and last a steadfast friend, who for a while was my boss and mentor, and who as one of this country's great mining geologists has laid his hand to the making of many a mine. I will doubly cherish the memory of the honor bestowed upon me because the presentation of the Jackling Award was made by this man. After the Lord made Dick Hunt he threw away the mold. Metals and other mineral products are essential ingredients of the social economy of the modern world. No well informed and thoughtful person can doubt that they will be indispensable to mankind as long as the fabric of civilization as we know it today can be held together. They are mined from ore bodies, which, unlike some other kinds of bodies, are physically inorganic and wholly incapable of reproducing themselves. Since in time they become mined out, an endless procession of new producers must be made by someone if the fundamental needs, to say nothing of the not so fundamental whims of an affluent society, are to be gratified. In saying that these mines must be made, I mean exactly that. It is my purpose to comment upon some of the problems we must cope with in making them. I shall try to avoid dwelling needlessly upon aspects of new mine development with which most people in this business are thoroughly familiar, and will attempt to discuss in a useful way some of the newer and more significant features of the economic climate in which these endeavors must be conducted. To begin with, an Almighty force put the ore into the ground, and selected the places in which to put it. Mankind was not consulted. Beyond that stage, however, mankind must find the ore deposits and contrive to extract their contents and put them into useful service. In doing this, he must use tools and techniques devised by man to overcome obstacles created in part by nature, but also in part by man himself. And most importantly of all, in making the tools and applying the techniques, he must use people. In the whole process the most pliable ingredient at hand-and also the most unpredictable-is people. Mines play out, and men die. As time goes on, we will have new mines, and they must be made by new men. The Environmental Dilemma It is perhaps timely to touch first upon the newest and in many ways the most potent consideration affecting the feasibility of developing new mines-the problems related to protection of the environment and to the

Jan 1, 1973

By Walter S. McKee

When mixed with common cast steel in quantities ranging from 11 to 131/2 per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time.. * At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 Ib. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13.5 per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 51/2 in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 51/2 in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an important consideration if the casting is to be a moving part in a machine. At the same time, the thickness of 51/2 in. is sufficient to permit the use of manganese steel for the heaviest classes of machinery.

Jan 1, 1916

By T. P. Harrington, P. G. Doctor, K. A. Prisbrey

Crushing and grinding ore consumes so much energy that it represents a major component of total processing costs. While it has been estimated that only about 0.6% of the total energy expended in grinding is actually used to create new surfaces, accurate measurement of this quantity is difficult. If energy expended in crushing and grinding could be more directly measured, alternatives for increasing efficiency of the processes could be evaluated more effectively. Since the energy intensity associated with rock fracture is related to fracture sonority, it should be possible to use this sound (acoustic emission) to measure the actual energy expended. However, it is difficult to apply this approach because the mill environment is so noisy. To make the approach practical, a method for differentiating acoustic emissions caused by rock fracture from those caused by extraneous noises must be found. Pattern recognition analysis may provide such a method. This paper presents the results of pattern recognition analysis to make two types of differentiations: acoustic emissions caused by crushing two types of minerals (quartz and chrysocolla) and those caused by two extraneous noise sources, and acoustic emissions produced by each mineral.

Jan 1, 1982

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that eventually the hydrometallurgist would have a wide selection of commercially available chemical reagents to make separations efficiently and economically of virtually all metals in solution under a wide range of conditions. Several years ago, General Mills began a research and development program to determine if it were possible to develop a reagent to extract a specific metallic ion from solution at a cost that would allow large scale commercial application. A giant step toward reaching this objective was announced in late 1963, when development quantities of LIX®-63 reagent, a highly selective reagent for the extraction of copper, were first offered to industry. The properties of this reagent were de- scribed in a previous paper.1

Jan 12, 1965

By Joseph Pogue

THE writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, FIG. 1.-SKETCH MAP SHOWING APPROXIMATE LOCATIONS OF ALL IMPORTANT EMERALD MINES AND PROSPECTS IN COLOMBIA. (Data in part supplied by Robert Scheibe, July, 1915.) Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 5, 1916

By AIME AIME

Acid Open-Hearth Manipulation.. By ANDREW MCWILLIAM and WILLIAM H. HATFIELD, ii, 279. Discussion by J. J. MORGAN, iii, 647; E. H. SANITER, iii, 648; MCWILLIAM and HATFIELD, 111, 648. ADDICKS, LAWRENCE. The Effect of Impurities on the Electrical Conductivity of Copper, iii, 559. Address of Welcome to the U. S. National Museum, Washington, D. C. By RICHARD RATHBUN, .iv, 923. ALLDERDICE, TAYLOR. Discussion of MR. ROE'S paper, The Mann¬ facture and Characteristics of Wrought Iron, v, 1091. American Mining Engineer. Discussion by ARTHUR JARMAN, iii, 641. An Automatic Stock-Line Recorder for Iron Blast-Furnaces. By J. E. JOHNSON, JR., iii, 509. Anthracite-Washeries. By GEORGE W. HARRIS, vi, 1263.

Jan 1, 1907

By R. W. Culbertson, S. Kasper

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons (13.6 Mt) of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past 25 years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated

Jan 1, 1980

By AIME AIME

A SPECIAL meeting arranged by the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers was held on Tuesday and Wednesday, Sept. 21 and 22, in the Assembly Room of the American Annex Hotel, St. Louis, Mo. Preceding the first session on Tuesday morning, the members and guests were registered and presented with the usual Institute badges. The morning session was opened at 10:30 by Ralph Arnold of Los Angeles, Calif., Chairman of the Petroleum and Gas Committee. In his opening remarks, he suggested that the petroleum section specialize more and more on the technical problems of the oil industry and that an effort be made to enlarge the membership of the Institute among the technical men of the industry. The following program was presented : OIL FIELDS OF RUSSIA, by A. Beeby Thompson and T. G. Madgwick, of London, England. Presented by H. A. Wheeler; discussed by Arthur Knapp and R. VanA. Mills. This most comprehensive paper was one of what is hoped to be a series to be presented by some of our foreign members. It is by far the best description in English of the world-famous Baku and other fields of Russia.

Jan 1, 1920

By C. EDWARD STAFFORD

A Discussion of the paper by Mr. James P. Roe which was read at the Washington meeting, May, 1905. MR. C. EDWARD STAFFORD, Chester, Pa.:-During all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horse-shoes and in the making by Dr. Otto Wuth's process extremely pure low phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces to make extra locomotive fire-box steel. I have also seen the Dank's puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Dank's blooms were made solely for open-hearth melting-stock to which they were well adapted ; the unavoidable presence of bits of ore-fix imbedded in the mass of the, metal always prevents the profitable manufacture of merchant iron from Dank's blooms. With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a. height of 17 or 18 ft. above the general level; the oscillation (65° each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Sep 1, 1905

By Thomas Leonard Watson

Introduction,...... Historical Statement,....644 Geology of the District,....645 The Weisner Quartzite,....647 Topography,. .....653 Rock-Weathering,..... The OcheR-Deposits,.....655 Petrography of the Quartzite,..655 Associated Ore-Deposits,....657 Chemical Composition of the Ocher,. 658 Mode of Occurrence of the Ocher,..659 In the Fresh Rock,....660 In the Residual Clays,...661 Origin of the Ocher,....662 Economic Features,..... Methods of Mining,..... Preparation of the Ocher,...664 Uses,........ Introduction. Knowledge of the existence of yellow-ocher deposits in Bartow county, Georgia, dates back to the early mining of manganese- and iron-ores in the vicinity of Cartersville. Systematic mining of the ocher in this area really began, however, probably not longer than a decade back, although the date of its first working is as early as the year 1877. The district has been, for a number of years, one of the principal producers of yellow ocher in the United States; and at no period of its development have mining activities been greater and more successful than at present. Systematic field-study of the ocher- and manganese-deposits of Georgia was begun by me while I was a member of the

Jan 1, 1904

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1918, to Nov. 9, 1918. ALLER, FRANK D., Copper Met., Ore Purchaser, American Smelt. & Refin. Co., 120 Broadway, New York, N. Y. AVÈRY, PAUL W., Met. Engr., Esperanza Min. Co., Apt. 8, El Oro, Mex., Mexico. BAKER, CHARLES A., Leaching Foreman, Copper Leaching Plant, Anaconda Copper Min. Co., Anaconda, Mont: BREED, CHARLES H Met., Crown Cork & Seal Co., Baltimore, Md. CHASE, R. L., Min. Engr 102S First National Bank Bldg., Denver, Colo. EICHELBERGER, FRANK, Vice-pres. and Engr., New York-Montana Testing & Engrg. Co., Helena, Mont. GESTER, G. C., Geol., Standard Oil Co. of Cal., 616 Standard Oil Bldg., San Francisco, Cal. GRIFFIN, JOHN, Mgr., Anthracite Territory, The Dorr Co., Board of Trade Bldg., Scranton, Pa. HAYNES, ELWOOD Pres., The Haynes Stellite Co., Kokomo, Indiana. Hsi, T. C:.. Sec'y, Tayeh Iron & Steel Works, Tayeh, China. HYDE, AUSTIN T., Mgr., Keokuk Plant, River Smelt. & Refin. Co., 607 Franklin St., Keokuk, Iowa.

Jan 12, 1918

By JOHN A. MALONEY

AS noted in the February issue of MINING AND METALLURGY, an advisory committee to the Museum of Science and Industry of Chicago was authorized by the Institute's Board of Directors, with W. R. Wright of Chicago, former Director of the Institute, as chairman. Since that time the committee has been undergoing organization, and held its initial meeting at the Museum offices in Chicago on April 11 and 12. Functioning as consultants to the Geology and Mineral Industries branch of this new institution, the advisory committee is aiding in building an exhibit which will tell the story of geology, mining, and metallurgy to millions of visitors a year. Although patterned to some extent

Jan 1, 1932

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By J. W. Harshbarger, E. L. Montgomery

The region of metallic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 6 km (19,700 ft). Because surface water supplies are meager, new mines require unexploited sources of water. Prolific ground water aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate ground water quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum capacities of more than 170 L/sec (2700 gpm) for individual production water wells. Results of investigations conducted by the authors demonstrate that ground water reservoirs in the Andean Highlands comprise a source of large quantities of water for the mineral industry.

Jan 1, 1986

By Arthur F. Colombo, Donald W. Frommer

With the opening of the Tilden mine near Ishpeming, MI, a new era in iron ore beneficiation was begun. A description of a U. S. Bureau of Mines investigation is summarized to illustrate the selective flocculation-deslime-flotation process developed by the Bureau and used at the Tilden concentrator, which is also briefly described. The operating parameters for the selective flocculation-cationic flotation of an oxidized taconite from the Mesabi range are discussed. A water reclamation system using lime and a cationic flocculant was applied to reclaim the effluents from a 900-pound-per-hour flotation pilot plant. About 80 percent of water requirements were recovered, and the calcium content of the reclaimed water was found to be more important than clarity in influencing the selective flocculation and flotation processes. Although reclaimed waters with about 10 ppm calcium registered turbidities of approximately 5,000 ppm SiO2 equivalents, the concentrates produced using these waters contained 64 percent Fe and 55.0 percent SiO2 and had accompanying iron recoveries of 75 percent. Lower grade concentrates resulted from using reclaimed water with higher calcium contents and lower turbidities.

Jan 1, 1976