Search Documents

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By H. J. Ramey, I. S. Bousaid

Experimental results on the oxidation reaction kinetics in the forward combustion oil recovery process are presented. A total of 48 runs were made wherein a stationary thin layer of coked, unconsoli-dated sand was burned isothermally in a combustion cell. Individual runs were made at various temperature levels to permit determination of the effect of temperature upon the reaction. An expression was obtained for the burning rate of carbon as a function of carbon concentration, combustion temperature and oxygen partial pressure. The carbon burning rate for two types of crude oil indicated a first order reaction with respect to both carbon concentration and oxygen partial pressure. The effect of combustion temperature on the reaction rate constant matched the Arrhenius equation. The activation energy was similar for the two crude oils examined. The activation energy decreased for a porous media containing clay. The rate of oxidation of crude oil at reservoir temperature was found to be significant. Other significant findings included information on hydrogen-carbon content of fuel residues, fuel reactivity and the products of combustion. INTRODUCTION The production of crude oil by underground combustion has been studied in the laboratory by many investigators.1-5 Results of laboratory and field experiments have been reported in the literature describing the forward combustion process. But as yet, no qualitative or quantitative study of the kinetics of fuel combustion involved in this process has been reported. The fuel concentration and the rate at which fuel is burned at the front are important factors governing the air requirement in a forward combustion operation. Although the fuel is essentially unrecoverable crude, the air required to burn the fuel is an important economic factor in this process. Because fuel is burned, the heat transport associated with forward combustion is a key and unique feature of this new oil recovery method. Many investiga-tors5-9 have presented information on the heat transmission and fluid mechanics involved in forward combustion. Berry and Parrish10 demonstrated the utility of considering reaction kinetics in reverse burning. From differential thermal analysis, Tadema11 presented a qualitative discussion of the nature of reactions between oil and oxygen in combustion oil recovery. Although little quantitative work has been done on the reaction kinetics involved in forward combustion oil recovery, an extensive literature does exist on combustion of carbons and oils, and carbonaceous residues from cracking catalyst pellets. Dart, et al., 12 studied the combustion rate for oxidation of carbonaceous residues on clay catalyst pellets, and found the reaction to be second-order with respect to carbon concentration, and first-order with respect to oxygen partial pressure for carbon concentrations less than 2 weight percent of the catalyst weight. The reaction appeared to be first-order with respect to carbon concentration for concentrations greater than 2 percent. Metcalfe13 noted that other workers had found that aging of the fuel during the combustion process was responsible for changing coke properties, and it accounted for the apparent second-order carbon concentration effect found by Dart, et al. It appears that burning of residues from cracking pellets is first-order with respect to both carbon concentration and oxygen partial pressure. Dart, et al., also observed that hydrogen in the hydrocarbon residue appeared to react faster than the carbon. Lewis, et al.,14 studied oxidation of charcoal, coke and graphite in a fluidized bed. Gas velocities were high enough to partially lift and circulate the carbon particles. Their results indicated first-order reaction dependency with respect to both carbon concentration and oxygen partial pressure. One

Jan 1, 1969

The First Conference of the Powder Metallurgy Committee convened in the East Foyer of the Hotel Waldorf-Astoria, New York City, at 9:45 a.m., on Feb. 21, 1944, Mr. John Wulff, General Chairman, presiding. THE CHAIRMAN.-In behalf of the American Institute of Mining and Metallurgical Engineers I welcome all members and guests to this conference on Powder Metallurgy. We hope that this meeting will give expert and novice in the field a chance for discussion. Unfortunately, the subject has been overemphasized by some, and, of late, severely criticized by others. We have here today powder producers, fabricators, and engineers of different viewpoints, who can make the meeting a success. Such success depends not only on the caliber of the papers presented but more so on the discussion. To give you time for a free exchange of views, the papers have been shortened purposely. With the hope that you will all benefit by this conference, I shall turn the meeting over to the Chairmen of the morning session, Mr. Roland P. Koehring, of Moraine Products Division of General Motors, and Dr. R. K. Waring, of the New Jersey Zinc Company. SESSION ON DESIGN FACTORS IN POWDER METALLURGY R. P. Koehring and R. K. Waring presiding The opening paper of the session was presented by Mr. Fred P. Peters, as follows:

Jan 1, 1945

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05 ? ACKER, E. O'C., Supt., Treatment Dept., Bethlehem Steel Co., So. Bethlehem, Pa. '86

Jan 1, 1910

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By W. P. Haynes

ESTIMATED United States crude-oil production during 1943 established a new annual peak of 1,500,000,000 barrels, a daily average of 4,118,000 barrels. This would be an increase of 315,000 barrels per day, or 8 per cent over 1942 and 7 per cent over 1941, the previous peak. During the first ten months of the year, production jumped from 3,782,000 barrels per day in January to 4,400,000 in October. Available data for the last two months of the year indicate a leveling off of this trend, with daily rates slightly above 4,400,000 barrels.

Jan 1, 1944

By Jack C. Haptonstall

This paper describes the analytical characteristics of Western subbituminous coal and the manner in which these characteristics apply to their use in a utility-sized steam generator. It compares these characteristics with those of typical Midwestern coal and Eastern bituminous coal. The paper also reviews in detail the design considerations that must receive attention when various blends of these three coals, or any combinations thereof, are planned to be used. This research paper describes variations in analytical and utilization characteristics when coals from different origins are blended in order to achieve a predetermined sulfur content for the purpose of predicting sulfur oxides emissions as they affect environmental regulations and the resulting alterations in utilization characteristics such blending would cause, and how such blends of coal would affect a utility-sized steam generator.

Jan 1, 1979

By AIME AIME

THE paper by C. H., Lieb on the "Economics of Oil-Producing Practice" (June issue, M. & M.) contains much food for thought. The engineers should be gratified that an executive with Mr. Lieb's. responsibility should recognize their standing in the industry. Yet after giving them that recognition, he proceeds to spur them on to greater accomplishments by pointing out that their job is only partly done and in some instances poorly done. The operating policies in this paper when applied to new pools with flowing wells are sound. Neither do I take exception to their application to pumping wells. But I do wish to comment on what lie says about price when applied to the many more wells that are approaching abandonment that is, the small producing wells. Mr. Lieb states in effect that higher prices would be detrimental from the long range viewpoint. I doubt that the present prices of crude will provide an ample return from the hundreds of thousands of small wells that have possibilities of substantial recovery by means of water-flooding, repressuring with gas, and air drive. Probably expenditure for experimental work can he justified, but at this time it must usually be considered as experimental. Recently I visited a property where it was estimated that $250,000 would be spent on a 160-acre tract for flooding purposes. The rate of r e t n r n and amount of profit at today's prices are uncertain. It can be argued that if this type of recovery is not economic with crude at $1 then it can he delayed as it is now possible to secure economically an ample supply of crude from our flush fields. But these old fields still retain large quantities of crude in a dormant state, and should not he abandoned per-

Jan 1, 1936

By Ian Wark

IN an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solu-tion composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents-namely, sodium cyanide-on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electro-lytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60°. There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1933

By R. G. Bowman

DISCUSSIONS of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, ii indicates that the .compound possesses characteristics that make it unique among white pigments, and superior to all ;in its particular field. A greater variety of processes have been proposed for manufacturing white lead than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints has been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not-new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the, production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful.

Jan 9, 1925

By Russell A. Carter

Seven years of rising silver prices have effectively revived an historic Idaho mining district and given it a new lease on life. Initial production earlier last year from the DeLamar open-pit silver mine in southwestern Idaho ushered in a new era of mineral production in a region that has weathered boom-and-bust cycles reaching back the better part of a century.

Jan 1, 1978

By D. L. McElroy, J. L. Schroder

Although the earliest use of rubber-tired haulage was in Illinois in 1936, the first unit of this type of equipment used in West Virginia was shipped into the state in 1938. All units placed in West Virginia mines have been of the shuttle-car type. The Katherine Coal Mining Co., at Lumberport, W. Va., was the second company in the United States to install shuttle cars and the Gay Coal and Coke Co., at Mt. Gay, W. Va., was the first company in the country to install the thin-bed type of shuttle car. On Oct. 8, 1940, nine companies in the state were using 41 shuttle cars, of which 10 cars at three mines were of the thin-bed type. All shuttle cars of the low type were in the southern fields and all of the high type were in northern West Virginia. At that time several units were in the process of delivery. The data in this paper were collected in the field by Mr. Schroder in connection with graduate work on mechanical loading of coal in West Virginia by mobile loaders. In the course of his field work he visited five mines in the state that were using shuttle cars. All of these mines were in high-volatile coal beds of strong structure. The more pertinent data obtained at the mines visited are given in Table I. The maximum distance of shuttle-car haul is the distance between the transfer station and the farthermost place. Tonnage per loading unit per foot of bed thickness is to some degree a measure of relative efficiency, especially if the different operations are working the same bed or have somewhat similar conditions. The thin-bed operation is well up in the higher bracket of the afore-mentioned column, which is as

Jan 1, 1942

By J. L. Schroder, D. L. McElroy

Although the earliest use of rubber-tired haulage was in Illinois in 1936, the first unit of this type of equipment used in West Virginia was shipped into the state in 1938. All units placed in West Virginia mines have been of the shuttle-car type. The Katherine Coal Mining Co., at Lumberport, W. Va., was the second company in the United States to install shuttle cars and the Gay Coal and Coke Co., at Mt. Gay, W. Va., was the first company in the country to install the thin-bed type of shuttle car. On Oct. 8, 1940, nine companies in the state were using 41 shuttle cars, of which 10 cars at three mines were of the thin-bed type. All shuttle cars of the low type were in the southern fields and all of the high type were in northern West Virginia. At that time several units were in the process of delivery. The data in this paper were collected in the field by Mr. Schroder in connection with graduate work on mechanical loading of coal in West Virginia by mobile loaders. In the course of his field work he visited five mines in the state that were using shuttle cars. All of these mines were in high-volatile coal beds of strong structure. The more pertinent data obtained at the mines visited are given in Table I. The maximum distance of shuttle-car haul is the distance between the transfer station and the farthermost place. Tonnage per loading unit per foot of bed thickness is to some degree a measure of relative efficiency, especially if the different operations are working the same bed or have somewhat similar conditions. The thin-bed operation is well up in the higher bracket of the afore-mentioned column, which is as

Jan 1, 1942

By Benjamin L. Miller, Charles H. Breerwood

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By Charles H. Breerwood, Benjamin L. Miller

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By Arthur S. Dwight

From the latest and best literature on lead-smelting, little can be learned concerning the present state of the art of mechanical feeding in the United States. H. O. Hofman, in his Metallurgy of Lead (5th ed., 1899), briefly describes the main features of the system in use at Pueblo, Colo., and later (p. 235) says " the only successful mechanical feeding, as far as the writer is aware, is that found at the works of the Pueblo Smelting and Refining Co." H. F. Collins, in his Metallurgy of Lead and Silver (London, 1899), covers American practice pretty thoroughly; but as to mechanical charging, he says: "The German plan of taking off the gases by means of a small iron pipe suspended in the center, and the plan of charging by means of cup and cone, as in iron blast-furnaces, have both been tried, but have not found favor, chiefly on account of the difficulty of obtaining free access to the furnace-shaft for barring, etc., with such devices."' . H. W. Hixon, in his Notes on Lead and Copper Smelting (3d ed., New York, 1900), gives a description and drawing of the Hixon feeding device, as originally installed at East Helena. Evidence that this system of feeding has passed its experimental stage, and deserves more serious consideration than it has heretofore received, is furnished by two large plants—the Pueblo and the East Helena—of the American Smelting and Refining Co., where mechanical feeding has been in continuous and successful operation for a considerable period; one new plant now erecting at Salt Lake City, Utah, and one old one belonging to the same company, the El Paso works, now being rebuilt after a disastrous fire, in both of which mechanical feeding is to be a prominent feature ; one new plant of an independent concern at Torreon, Mexico, which will adopt mechanical feeding; and a number of other smaller plants, among

Jan 1, 1902

By V. C. Perini

The North Central Texas district as herein defined includes the counties of Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summer-ville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. In the new designation of districts for the Transactions, the North Central Texas district includes most, but not all, of the counties of the previously classified West Central Texas district. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The greater part of the oil and gas produced in this district has been from Pennsylvanian strata. Some oil and gas has been produced from the lower Permian (by the latest, selection of the Pennsyl-vanian-Permian boundary) and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. These features are found by surface and subsurface geological structural mapping, by core drilling and by geophysical surveying. Geochemical methods are also the basis for some wildcatting. The demand for sweet crude oil from this district is firm for local and national consumption, but the market price for the oil remains practically the same as in 1941. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, tievelopment and wildcatting costs. Stripper wells are being plugged daily and should be jealously saved for the future local and national reserves, especially in view of the fact that new discoveries of commercially important oil and gas reserves are not keeping pace with consumption. An expected economic disruption attendant upon the national war effort has arisen and continues in the future outlook for this district. The lack and delay of securing replacement parts for almost all oil-field equipment has handicapped and delayed operations and has decreased efficiency in wildcatting, development and production. Sufficient experienced drilling, scientific and office personnel is lacking because of inductions in the armed forces and migration to war industries during the period before manpower conservation became effective. The office personnel of the average oil and gas producer continues to be swamped by the increasing demands for reports by state and federal bureaus. An average of IQ days

Jan 1, 1944

By V. C. Perini

The North Central Texas district as herein defined includes the counties of Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summer-ville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. In the new designation of districts for the Transactions, the North Central Texas district includes most, but not all, of the counties of the previously classified West Central Texas district. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The greater part of the oil and gas produced in this district has been from Pennsylvanian strata. Some oil and gas has been produced from the lower Permian (by the latest, selection of the Pennsyl-vanian-Permian boundary) and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. These features are found by surface and subsurface geological structural mapping, by core drilling and by geophysical surveying. Geochemical methods are also the basis for some wildcatting. The demand for sweet crude oil from this district is firm for local and national consumption, but the market price for the oil remains practically the same as in 1941. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, tievelopment and wildcatting costs. Stripper wells are being plugged daily and should be jealously saved for the future local and national reserves, especially in view of the fact that new discoveries of commercially important oil and gas reserves are not keeping pace with consumption. An expected economic disruption attendant upon the national war effort has arisen and continues in the future outlook for this district. The lack and delay of securing replacement parts for almost all oil-field equipment has handicapped and delayed operations and has decreased efficiency in wildcatting, development and production. Sufficient experienced drilling, scientific and office personnel is lacking because of inductions in the armed forces and migration to war industries during the period before manpower conservation became effective. The office personnel of the average oil and gas producer continues to be swamped by the increasing demands for reports by state and federal bureaus. An average of IQ days

Jan 1, 1944

By J. Holms Pollok

The determination of specific gravity dates from such antiquity, and the various published methods of determining it are so numerous, that one may well be skeptical as to the value of a new means of obtaining so well-known a quantity. I make no claim to any great novelty for the little device here described, the principles, though not the convenient details, of which are more or less embodied in the publications of Mr.

Jan 1, 1900