Search Documents

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

William R. Walker, assistant to the president of the U. S. Steel Corpn., died at St. Luke's Hospital, New York, on Dec. 20, 1922. He was born at LaPort, Ind., Nov. 26, 1857, and his whole career has been closely identified with the iron and steel industry. His first employment was with the North Chicago Rolling Mill Co., Chicago; then he was appointed chemist for the Crown Point Iron Co., at Crown Point, N. Y.; and later he was works superintendent for Spang, Chalfant & Co., of Pittsburgh. He was early associated with Robert Forsyth, the well-known engineer who constructed the South Chicago works of the North Chicago Rolling Mill Company. Prior to 1890, Mr. Walker was works manager for the Union Steel Co., and upon organization of the Illinois Steel Co. he became general manager of its South Chicago works. At the time of the formation of the U. S. Steel Corpn., in 1901, he was appointed assistant to the president, which position he held until the time of his death. Through the technical staffs and committees of the Steel Corpora tion, Mr. Walker had an excellent opportunity to study and direct the development of mechanical methods for coal mining, coal washing, beehive coking, including the collection and recovery of its byproducts, and to interest himself in byproduct coke ovens, and the design and operation of processes for the coking of special coal mixtures. He also brought his experience to bear on the design, construction and operation of the blast furnace and its appurtenances, as well as the bessemer, open-hearth and electric steel processes. Incidentally, he was interested in microscopy and metallography, and was familiar with the manufacture of products related to the iron and steel industry, such as tin, zinc, sulfuric acid and many other substances. Mr. Walker had the remarkable faculty of being able to discuss and conduct investigations in practically any technical branch of the ferrous industry. In the words of President James A. Farrell, "Mr. Wdker was a man of keen mental attainments and possessed an exceptional knowledge of the iron and steel industry, from both the scientific and the practical

Jan 1, 1923

William R. Walker, assistant to the president of the U. S. Steel Corpn., died at St. Luke's Hospital, New York, on Dec. 20, 1922. He was born at LaPort, Ind., Nov. 26, 1857, and his whole career has been closely identified with the iron and steel industry. His first employment was with the North Chicago Rolling Mill Co., Chicago; then he was appointed chemist for the Crown Point Iron Co., at Crown Point, N. Y.; and later he was works superintendent for Spang, Chalfant & Co., of Pittsburgh. He was early associated with Robert Forsyth, the well-known engineer who constructed the South Chicago works of the North Chicago Rolling Mill Company. Prior to 1890, Mr. Walker was works manager for the Union Steel Co., and upon organization of the Illinois Steel Co. he became general manager of its South Chicago works. At the time of the formation of the U. S. Steel Corpn., in 1901, he was appointed assistant to the president, which position he held until the time of his death. Through the technical staffs and committees of the Steel Corpora tion, Mr. Walker had an excellent opportunity to study and direct the development of mechanical methods for coal mining, coal washing, beehive coking, including the collection and recovery of its byproducts, and to interest himself in byproduct coke ovens, and the design and operation of processes for the coking of special coal mixtures. He also brought his experience to bear on the design, construction and operation of the blast furnace and its appurtenances, as well as the bessemer, open-hearth and electric steel processes. Incidentally, he was interested in microscopy and metallography, and was familiar with the manufacture of products related to the iron and steel industry, such as tin, zinc, sulfuric acid and many other substances. Mr. Walker had the remarkable faculty of being able to discuss and conduct investigations in practically any technical branch of the ferrous industry. In the words of President James A. Farrell, "Mr. Wdker was a man of keen mental attainments and possessed an exceptional knowledge of the iron and steel industry, from both the scientific and the practical

Jan 1, 1923

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work' the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,' Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

COLUMBIA SECTION J. C. HAAS, Chairman W. J. HALL,. Vice-chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY J. F. MCCARTHY At a meeting of the members of Columbia Section, which was held in the Davenport hotel, Spokane, Wash., Jan. 31, 1919, at noon, there were present' about twenty members and guests. The chairman being absent, Mr. Frederick Keffer presided. The Secretary announced the personnel of the executive committee of the section, which is: J. C. Hass, Spokane, Chairman; W. J. Hall, Wallace, Ida., Vice-chairman; S. S. Fowler, Riondel, B. C., Past Chairman; L. K. Armstrong, Spokane, Secretary-Treasurer; R. M. Betts, Cornucopia, Oregon. It was stated that the geological survey and report on Stevens Co., Wash., has been completed and will be printed soon. The geologic survey of Colville Indian reservation, by J. T. Pardee, U. S. G. S., has been published as Bulletin No. 677 and is available for distribution, The Miner's Almanac, Miners Circular No. 24, U. S. Bureau of Mines. is also available upon request. There was considerable discussion on the program for meetings during the year. It was informally agreed that, if agreeable to Coeur d' Alene members, that one meeting should be held in that district, preferably at the time of the annual visit of Institute officials. It was also proposed to hold at least one open-air meeting in Spokane with suitable program. The activities of other sections were noted with favorable comment. In this connection there was much general discussion on the subject of closer relations between the national engineering societies. It was agreed that cooperation was desirable and imperative if the greatest measure of value be realized from the profession. It was not the sense of the members, however, that complete amalgamation is desirable. This expression of local sentiment is to be presented to the Institute

Jan 3, 1919

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968

A. L. BLOMFIELD, ? Colorado Springs, Colo. (written discussion?).¬I congratulate the author on bringing out a paper of real service to the profession. His contention of uniform size in balls is borne out by my own experience; in coarse crushing at the Golden Cycle in 6 by 6-ft. (1.8 by 1.8-m.) ball-mills we unquestionably gain by screening out the small balls once or twice a month. The point of gaging the ball size to be used by the uniformity of screen sizing is of particular interest. The necessity of sufficient return feed from classifier to the ball-mill is sound and clearly shown. In connection with this, I wish two further points had been gone into as thoroughly: (1) The effect of the quality of classification. In general, it is true that the smaller the per cent. of undersize in the feed the more effective is the mill's work. This is true on a bucking board, in tube-mills, ball-mills, and grinding pans. Given the possibility of returning. a full-feed load to any mill, it has been my experience that the effective work in the grinder is almost proportional to the quality of the return feed. (2) Again speaking generally, the shorter the tube-mill the greater is the quantity of return feed necessary to keep it loaded. The classification thus keeps the oversize in the mill more free from finished product and thus the crushing more efficient. It is very easy to overload any long mill with too much return

Jan 4, 1919

By G. A. Vissac

O. R. LYONS *—I wish to thank Mr. Vissac for his compliment. I hope that his paper is not only well received, but that it will serve to bring forth more papers on the subject of thermal drying. One of the primary purposes of the work performed by Battelle for Bituminous Coal Research in investigating the thermal drying of coal was to stimulate other investigators and to get them to contribute their knowledge in the form of papers such as this one. We at Battelle and the personnel of Bituminous Coal Research are very gratified that Mr. Vissac and other persons have responded in this matter of the thermal drying of coal. I wish to state that I think that Mr. Vissac's paper is a very clear and easily understood description of a method of calculating the design requirements for a screen type drier, and I think that it would be exceedingly valuable to operators and to those who intend to purchase any type of thermal drier and use it in the future, if the manufacturers or operators who have such information for other types of driers would provide the same type of information for the other makes of driers now on the market. 1 also wish to point out—an idea that is new to me, and I know is new to most of the operators of driers in the United States-—the idea of recovering the heat that is normally lost in the coal and in the exhaust gases. This heat is not being recovered at most (of the thermal drying operations in the United States, and the possibility of recovering it should be called to the attention of every single one of those operators. I know many of them have never given any thought to the matter, but they will be interested once they realize the ease with which it could be done and the savings that could be realized. I also wish to compliment Mr. Vissac for presenting the method of analysis that he uses to determine the difficulty of drying any particular coal. It is a very simple method, and yet it seems to me that it should be a very effective, very efficient method for determining the difficulty of drying for his particular problems. C. Y. HEINER*—I do not know that I can add anything very illuminating to what Mr. Vissac has said. I think anything that Mr. Vissac said in regard to coal drying is a contribution because, to my personal knowledge, he has studied the matter carefully for many years and made many valuable contributions. I am not too familiar with coal drying problems in the east, but I know in the west we have not made enough coal drying studies. I think coal operators too often just take the coal as it is and make more or less the best of it. There are relatively few washing plants in the west now, and so the problem has not come to the front as much as it probably will in the future. In this connection, it seems to me that this matter of drying the raw coal, as Mr. Vissac brings up, is an extremely important one. We have not a continuous miner ourselves, yet, but we expect to get some this year, and we think the percentage of fine coal-—that is, minus 3/16 in.—will double. We have about 20 pct minus 3/16 in. in the 8 in. by 0 size now, and we think we will likely have 40 pct, which will have a surface moisture of the order of 8 pct. To wash it satisfactorily, we will have to dry the raw coal first in order to screen it, and after that, I suppose, there will have to be dry cleaning of some sort. We have not really used dry cleaning on fines in the west yet to my knowledge, but it is a matter that has to be faced by the industry, and I am very hopeful that Mr. Vissac's study will assist us in that connection. W. L. McMORRIS*-In my company we are preparing largely metallurgical coal for a great number of byproduct coke plants. The most outstanding thing to me about the requirements of moisture in the finished product is that there is a different requirement for almost every coke plant. Each operator has a different set of factors on which he establishes his coking costs where they involve moisture. For our corporation operations in Birmingham, my company does not produce the coal, but in Birmingham they are getting away with moistures very much higher than our plant at Clairton, Pa., would tolerate. The moisture that we have to produce for the plants along the lakefront where they are subject to much more severe weather is something else again. We have not tackled heat drying, primarily because our customers do not know what heat drying will do to the coking characteristics of the coal. If the temperature of drying can be held down

Jan 1, 1950

US 4,201,749-In the Bayer process production of alumina wherein aluminum hydroxide is precipitated from a sodium aluminate solution for use as seed, sodium oxalate and caustic components are removed from the precipitate by washing it first with a washing liquor which is saturated with sodium oxalate but has little content of caustic, and secondly with hot water. Substantially no sodium oxalate is recycled, yet loss of sodium aluminate is minimal. K. Yamada, T Harato, and H Kato, assigned to Sumitomo Aluminum Smelting Co Ltd May 6, 1980 8 pp. (423-127). Filed. 5-8-79 (37,145) Priority. Japan, 5-8-78 (53/54,803). Same¬British 2,020,642, dated Nov. 21, 1979.

Jan 1, 1982

By Benjamin C. Craft

A review of development in North Louisiana during 1936 centers around the Rodessa field, in Caddo Parish. Continued extension of the

Jan 1, 1937

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By W. P. Blake

Wm. P. Blake, New Haven, Conn. (Communication to the Secretary, June, 1889): It is gratifying to find that Prof. Carpenter in his paper sustains the accuracy of my original determination of

Jan 1, 1889

[Secretary's Note.—The following official tables, prepared by the government of the State of Nuevo Leon, and presented to the Institute at the fifth seseion of its Mexican meeting, held at Monterrey, November 26, 1901, present in compact form a general summary of the mineral and metallurgical industry of the State for the preceding calendar year, together with a statement of the railway-shipments of ores from January 1 to October 31, 1901, which, in the absence of direct official mining and metallurgical statistics (not yet available for that year), clearly indicates an increased activity and productiveness of these industries. In other words, the mines are reported to have yielded in 1900 a total product of 83,960,169 kilos of ore; whereas, the railway is reported to have carried, in 10 months of 1901, a total of 108,318,647 kilos of ore. At this rate, the railway-shipments for 1901 mould amount to nearly 130,000,000 kilos. It is, of course, possible that the railwaystatistics include other freight than ores, or that they include duplications, such as would be involved in the record, first of certain ores transported, and afterwards of the " base bullion " produced therefrom. An accurate comparison is therefore impossible ; yet, after making all reasonable allowances for such items as have been named, it seems safe to infer that the mining and metallurgical industry of this State accomplished in 1901 a substantial progress.]

Jan 1, 1902

By C. E. Coleman, D. Hardie, A. E. Wraith

A photoguaplric method of measuring crack velocities has been applied to an examilzation of- the effect of hydrogen on the impact properties of zirconium. Results indicate that the crack in hydrided zirconit travels at about 26 m per sec whereas that in the uacuum -annealed is dependent on the speed of the hammer. RECENT work on the effect of hydrogen on zirconium reveals that when hydrided zirconium is tested in slow bending the crack producing failure can be unstable. The mode of fracture seems to involve the crack linking up broken hydrides by a ductile mechanism in the zirconium matrix.2" In order to compare the fracture of zirconium with that of other metals which show unstable crack propagation, notably steel, the rate of the crack spread must be known. As the methods previously used for measuring crack growth are either unsuitable for the present work5-'' or very costly," a simple technique has been devised in which the maximum crack velocity is derived from a series of crack position-time measurements. EXPERIMENTAL PROCEDURE The experimental arrangement is shown schematically in Fig. 1. The flash unit12 was triggered when the Charpy hammer touched the specimen and the 6-psec flash of the lamp delayed by a preselected time interval in the range 100psec to 10 msec. The camera was left on open shutter during the test. From direct measurement on a calibrated photographic print, Fig. 2, the position of the crack and the specimen was found at a known time after impact and, from a series of such tests using an appropriate range of flash-delay times, the crack velocity was estimated. Preliminary experiments were carried out on mild steel above and below its transition temperature. Vacuum-annealed zirconium, and zirconium hydrided to 100 ppm H were then tested at 20" and 150°C. For comparison, Zr-2.6 pct Nb alloy (in the 0 + transformed /3 condition), vacuum-annealed or hydrided to 100 ppm H, was tested at 20 C. The chemical analyses of these materials are given in Table I. For the high-temperature tests a fine chromel-alumel thermocouple was spot-welded onto each specimen close to the notch. The test piece was heated up to 200°C to allow enough time for preparing the apparatus while the specimen cooled to the testing tem- perature. It was assumed that the specimen cooled uniformly. The accuracy of the flash-delay time was better than i2 pct i 5 psec. The crack length was taken as its maximum distance traveled normal to the length axis of the specimen. Errors in these measurements arise as a result of the uncertainty in the location of the crack tip and the difficulty in defining the exact position of the crack starting point. The latter was due to the bonding and large amounts of deformation at the hammer contact point, especially in the vacuum-annealed specimens tested at 150°C. The maximum error in the measurements was however estimated to be about 5 pct. DISCUSSION OF RESULTS From the trial experiments using mild steel above its transition temperature it can be seen from the plot of crack length against time after impact, Fig. 3. that a reasonable estimate of the maximum crack velocity at the surface of the specimen may be made. Other features of note are the initiation time before the crack is first seen and the slowing down period

Jan 1, 1967

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

Thomas H. Beddall, so we are informed by Major J. B. Carlock, has been promoted and is now Adjutant of the 1st Battalion, 1st Gas Regi¬ ment. He was awarded, last summer, the Croix de Guerre. R. A. Bull. See letter in Proceedings of Milwaukee Meeting. Captain Stanley C. Bullock's record since entering the service is given as follows in a letter recently received from Mrs. Bullock: Resigned position of mine manager in Chile in November, 1915, to return to England to obtain commission in Royal Engineers. Joined Officers' Training Corps, Dec. 20, 1915. Commission gazetted, Jan. 27, 1916, 2d Lieut., R. E. Landed in France, Feb. 6, 1916. Posted to 179th Tunnelling Co., R. E. Took part in following battles: Somme, 1916; Ypres;1917; Arras, 1917; Somme, March and July, 1917; Messines, 1917. Gazetted: Acting Captain, July 11, 1916; Temp.-Lieutenant, Oct. 26, 1916; Captain, Sept. 29, 1918. Awarded Military Cross, Jan. 1, 1918, for conspicuous bravery and devotion to duty under a heavy enemy gas bombardment, when, by his example and perseverance in spite of every difficulty and obstacle, mining work was successfully completed which was vital for the success of the operations. The Cross was presented to Capt. Bullock by the King, on Sept. 25, 1918. First Lieut. J. J. Cadot, in a letter sent to Mr. H. `V. Hardinge from France, says he has been at the "Front." He also mentions that the Boche "is a good sprinter."

Jan 12, 1918

By John Gann

THE following investigation constitutes a brief resume of the more important binary magnesium alloys from the standpoint of metallographic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn.

Jan 1, 1928

By John Johnston

ONLY two of the Institute's 26 Local Sections were unrepresented at the delegates' three sessions, held on Monday morning and afternoon and Thursday afternoon of the annual meeting. The Philadelphia and Wyoming Sections alone sent no delegates. In all, seven hours were spent most profitably in reviewing the work done by the Institute at headquarters and in the field, comparing ideas and practices in varied activities, and in establishing personal contacts. Cordiality and the co¬operative spirit marked the meeting and apparently no one had any serious grievances to air. Four motions were introduced and unanimously passed. The first, which was introduced by B. L. Sackett, was a recommendation by the delegates that a national committee be appointed to cooperate with Local Sections in the matter of student activities, to promote Institute welfare. It was agreed that this recommendation be made simultaneously to the Board of Directors and to the Mineral Industry Education Division. A subsequent resolution by A. M. Smith was passed asking that a part of the duties of this committee be to secure the opinions of Local Sections as to the most desirable methods of interesting students in the preparation of technical papers, by giving prizes or otherwise, and to report their findings at the Section Delegates' meeting next year.

Jan 1, 1933

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of' density. A serial sectioning' technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski' in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968