Search Documents

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one. if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate. l7,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By C. van der Poel, R. L. Chuoke P. van Meurs

When an initially planar interface between two im-ttitcihle liquids is displaced at constant rate, U, nor-mat to the front, instability will occur for all rates greater than a critical rate. U, given by provided the Fourier decomposition of the spatial pertmrbcrtiott or deformation of the moving displacetment front contains modes with wavelengths. A, greater than a critical wavelength, given by tit there expressions, p, p and k, with the subscripts I and 2 distinguishing the two 1iquids under consideration, are density, viscosity and effective pemeability coefficients respectively; g is the absolute value of the acceleration due to gravity; and cos (zz') is the direction cosit7e between the vertical carlesian coordinate z' (positive upward) and the z coordinate norma1 to the initially plane macroscopic interface taken positive in the direction from Liquid I to Liquid 2. U is the average volumetric velocity (injected volume of liquid pet. unit time per unit of area normal to Z) and is positive for Liquid I displacing Liquid 2, negative for the reversc displacement and r2 is an effective inter-fucial tension (for displacements between parrallel plates, t0= s the ordinary bulk interfacial tension). further, there is a wavelength of maximum instability given by For natural perturbations, this wavelength will preclotninate and characterize the form of the instability as a quasi-sinusoidal deformation, i.e., viscous fitzgers of peak-to-peak separatiotr, A,,. Comparison of experitient with theory rei'eals tltat these considerations are recsonably valid for displacements in hoth parallel plate chantzels and nnconsoli-clutt'd glass ptnvder packs. These results are. tij particular interest for interpretation of data from laboratory experiments with regard to fielil applica/iotz.s. It is quite possible for A,, although st7zall relative to the large lateral dimension of the reservoir, to rxceed the greatr.st lateral extent of the lahoratory sample or model. If it does, frontal displace- ment occurs in the laboratory experiments, and oil INTRODUCTION Thc puposes of this paper are to present theoretical and experimental evidence for occurrence of macroscopic instabilities in displacement of one viscous fluid by another immiscible with it through a uniform porous medium and to compare available experimental data with some predictions of a theory of instability developed by the first author. The instabilities are referred to as macroscopic in the sense that spatially quasi-sinusoidal, growing fingers of the displacing liquid are formed, the width and peak-to-peak separation (wavelength) of which is large relative to a characteristic length of the particular permeable medium such as grain size. Visual models of two kinds have been used to obtain observations: displacement of oil by water-glycerine solutions through the flow channel formed by closely spaced parallel plates and displacement of oil by water with and without initial interstitial water through unconsolidated glass powder packs, employing the technique of matching indices of refraction. In all cases we have observed macroscopic instabilities or fingers under conditions predicted by the theory to be favorable for their occurrence. The phenomenon discussed here is not the production of streamers due to gross inhomogeneities such as permeability stratification of the porous medium. It is our object to show, on the contrary, that a quantitative prediction of finger spacing is possible in a porous medium known to be macroscopically homogeneous and isotropic throughout. The importance of the phenomenon in its influence on the configuration of oil and water with respect to oil production behavior was noted earlier by Engel-berts and Klinkenberg' who coined the term "viscous fingering". THEORY Necessary and Sufficient Conditions ior Instability anc Initial Kinematics There are several levels of increasing complexity in the theoretical description of instabiIity of fluid displacements in permeable media. Of these, the simplest description, ;tdapted to low permeability systems, is selected for presentation.' More inclusivc tlescriptions are reserved for separate publication.

By A. L. Marshall, F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C.oin a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. APPARATUS AND TECHNIQUE The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 0800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard' glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not 'a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by

Jan 1, 1944

By George I. Adams

PHYSICAL AND CLIMATIC DIVISIONS. PERU is divided into three regions-the coast, the sierra, or high mountainous region, and the a montana," or forest region of the Amazon basin. The Coast.-The coast is an arid region. No rain falls excepting in the extreme northern part, which borders the Gulf of Guayaquil. There is, however, a slight precipitation in the form of mist (garua), which occurs on the coast hills during the so-called winter months. The aridity of the coast is due principally to the antarctic or Humboldt ocean-current, which, being cold and having a temperature lower than that of the land, absorbs rather than produces vapors. The coast mists occur during the season when the land is relatively cold. Near the Gulf of Guayaquil the antarctic current diverges from the coast, so that in the Tumbes valley and adjacent country the conditions in the summer months are such as produce rains. In the remaining valleys of the coast, agriculture is made possible only by means of irrigation, and is accordingly very limited in extent, although rich and varied. In the northern and south-central portions of the coast, plains extend inland from the sea, while in the southern part there is a coastal plain separated from the Pacific by a range of coast hills. Between the northern and south-central plains, as well as between the south-central and southern, the foothills of the sierra descend to the seacoast. The Sierra.-The sierra embraces the high land dominated by the lofty cordilleras of the Andes. In the southern part of Peru there are two cordilleras, the western and the eastern, which enter from Chile and Bolivia respectively, and inclose between them the Titicaca Lake basin. To the north of Lake Titicaca these cordilleras unite in the knot of Vilcanota, south of Cuzco. From this knot three cordilleras, known as the western, the central, and the eastern, extend to the northward, reuniting in the

Jan 7, 1908

By L. E. Young

IT has been said the British Empire was built on British Coal. In all the postwar planning for Great Britain the necessity for producing cheap coal and the prosperity of the coal industry are given first consideration. On Jan. 23, 1945, there was released in London a "Report to the Colliery Owners" which had been awaited with great interest. This was entitled "A Plan for Coal" and was the recommendation of Robert Foot, chairman of The Mining Association (Colliery Owners), prepared at their request. Presentation of the "Plan" at this time is particularly significant as it is an answer to the demand for nationalization of the coal industry by the Labour Party and at the same time is a carefully considered program for postwar reconstruction, prosperity, and stability. In the words of Mr. Foot, If the coal industry for the first ten years after this war is to find itself in a situation similar to the one it occupied for the ten years following the last war, with its record of disputes, strikes, stoppages, short-time working, unemployment, and, with it all, a completely insufficient margin of profit, and all the insecurity and instability in our basic industry that was brought with them, it is goodbye to any real prospect of full employment, social security, and high standard of living. To present an elaborate review of the conditions which have brought to a crisis the unfortunate situation in the British coal industry is here unnecessary, but certain of the salient points

Jan 1, 1945

Who's Who in Mineral Engineering - The 1978 Membership Directory of the Society of Mining Engineers of AIME

Jan 7, 1978

By C. L. Dake

AN insistent and steadily growing demand is evident for the broadening of undergraduate curricula in engineering. Among suggested additions are training in public speaking, report writing, business law and contracts, accounting, finance, money and banking, scientific management, economics, social and labor problems, psychology, and ethics. The demand for these subjects comes from the older engineers and from the industries that employ our graduates. Of course, many of the men who suggest such changes are influenced largely by their personal needs and contacts, but the demand is sufficiently widespread to merit serious study by educators. In fact, many educators themselves concur in the proposals for broader training. These matters were examined intensively a few years ago in an exhaustive study of engineering education. Opinion at that time was rather strongly against any profound change. Since then, however, the whole economic system has undergone violent disruption. Even if recommendations made a few years ago were appropriate to the conditions then- obtaining, the enormously changed conditions of the present make advisable a further careful study of this problem. In recent years, mergers, to reduce costs, have sharply limited the number of engineers employed and have thereby intensified the struggle to secure positions. In this stiffer competition, engineers with the most adequate training undoubtedly fare the best.

Jan 1, 1934

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds ;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2 : I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium. some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17, 32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well's results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. 'This means that careful measurements of surges occurring in actual field operations must be made.

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By J. Gurland

The effect of four different second-phase additions on the strength of composite alloys with a common matrix was investigated. The four compositions each consisted of 85 pct by volume of silver with additions of 15 pct of either tungsten, molybdenum, tungsten carbide, or nickel. These particular additives were chosen because of their low mutual solid solubilities with silver at room temperature, the alloys consisting essentially of a dispersion strengthened silver matrix in which the second phase is distributed randomly. Test specimens were prepared by a powder metallurgy procedure consisting of ball milling the mixed powders, compacting, and sintering at 920°C for 1 hr in hydrogen. The constituent powders were of CP quality and of particle size between 2 and 10 ?. The compacts were subsequently hot pressed at 1000 psi and 1400° in an Inconel die, coined at room temperature at 60,000 psi and finally annealed and outgassed in vacuum at 800°F. The microstructures of the alloys are shown in Fig. 1, and the microscopically observed porosity grade was A-2 or better as evaluated by ASTM Recommended Practice B 276-54. The properties of the sintered compacts are listed in Table I, and the load-deformation curves in bending are shown in Fig. 2. The samples, of rectangular cross section, were loaded at the center of 58 in. span, and the reported stress was calculated on the basis of linearly elastic behavior in order to allow the comparison of specimens of slightly different dimensions. It is apparent that the tungsten, molybdenum, and tungsten carbide alloys exhibit very similar deformation curves. The moduli of elasticity were determined from the slopes of the stress-deflection curves at small loads. The measured values agree quite well with those calculated by the strength of materials approximation proposed by Paul1 for the elastic constants of mixtures, the calculated values being 15.0, 15.0, 17.4, and 13.4 million psi, respectively, for the tungsten, molybdenum, tungsten carbide, and nickel combinations with silver. The strength of the Ag-Ni composition is appreciably lower than that of the other three alloys. The discrepancy between the two groups is accounted for by the following characteristics of deformation and failure which were observed microscopically during the tests: A) The deformation of the W, Mo, and WC alloys did not involve the second phase particles to any appreciable extent. Slip and fracture took place in the silver-rich matrix alone, although the fracture path generally skirted the particles by favoring the phase boundaries. The deformation proceeded according to the following sequence: 1) formation of small, discontinuous microcracks in areas of the matrix adjacent to a particle, 2) general slip in the matrix and extension of cracks, 3) failure of specimens by propagation of cracks through matrix. The near coincidence of the 3 load-deflection curves suggests that the nature of the second phase particles does not decisively influence the plastic behavior of composite alloys of this composition as long as the particles do not undergo any considerable deformation themselves. B) A markedly different behavior was exhibited by the Ag-Ni composition where the relatively low flow strength is associated with the low yield strength of the nickel grains. Slip in the nickel grains was first observed at a stress of approximately 10,000 psi, although failure, at a later stage, took place by the propagation of cracks through the matrix. The ductility of this aggregate, in which both components deform plastically, is appreciably greater than that of the elastic-plastic composites. In summary: 1) The measured values of the moduli of elasticity of the composite alloys under discussion are in good agreement with the "strength of materials" approximation proposed by Paul.&apos; 2) The overall plastic behavior of these particle-strengthened alloys is unaffected by the nature of the second phase particles, if the latter remain elastic. This work was supported by the Office of Naval Research. The experimental results are presented

Jan 1, 1962

By A. B. Parsons

Jan 1, 1971

THE members arrived at Ticonderoga, N. Y., at noon, Tuesday, October 15th, and were received by Mr. Cyrus Butler, Chairman of the Local Committee of Arrangements. During the afternoon the works of the American Graphite Company and the Horicon Iron Company were visited under the guidance of Mr. Butler, President of both companies, and of Mr. William Hooper, Superintendent. An excursion was then made, in carriages, to old Fort Ticonderoga, on Lake Champlain, after which the party were driven to the Rogers Rock Hotel, on Lake George. The first session of the Institute was held in the parlor of time hotel on Tuesday evening. Mr. Eckley B. Coxe, President of the Institute, opened the proceedings with the following address: I shall ask your attention, this evening, to a few reflections upon the subject of mining engineering as a profession in the United States, its past, its present, and its future, and its duties and oppor¬tunities with reference to the proper development of our great min¬eral resources. Thirty years ago, there were scarcely any mining engineers in this country, and but few in England, and there were no institutions where young men could be educated for the profession in the Eng¬lish language. France and Germany have been able for about a century to boast of mining schools of a high character, that number among their graduates such men as Humboldt, Weisbach, Rittinger, Combes, and Gruner. Of the few we then had worthy of the name of "mining engi¬neer," some had studied in the continental academies, and others were graduates in the school of practical experience, and had learned their profession in mines and smelting-works. Their work con¬sisted principally in making surveys and maps of mines and mining properties, geological reports, and analyses of ores ; but the mining engineer whom we often meet with now, who has studied chemistry, physics, mineralogy, geology, mechanics, and drawing; who is more or less familiar with machinery and its construction, and with the practical management of mines or smelting-works, and who is an expert in some one branch of his profession, would have been very difficult if not impossible to find in the United States. The induce¬ments held out to ambitious and talented young men to enter the

Jan 1, 1879

By Robert Linton

THE PURCHASE of silver by the United States Government under the provisions of the Pittman Act is practically completed. Producers of silver in this country will now have to market their silver in competition with the rest of the world. It therefore becomes of interest to study such data as are available and endeavor to obtain such suggestions as may be afforded therefrom as to the probable future market position of the metal. Conditions influencing the marketing of silver are numerous and complex. It is a commodity entering. into the arts and manufactures, and therefore influenced by the condition of various lines of business which make use of it; it is currency-being used by all countries for subsidiary coins and even as the founda-tion of the system by a very few; and it serves as a frequent basis for speculation. The various factors involved can easily set up so many cross-currents in the flow of the metal that predictions in regard to the market position of silver can never be safely made, although it may be possible to form some idea of prob-able trends over a sufficiently long period. Of course price is determined, as is the case with all commodities, by the inexorable workings of the law of supply and demand.

Jan 6, 1923

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor&apos;s organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By William L. Saunders

Many members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary&apos;s approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-coxpressors and machinery driven by compressed air, has no desire to injure its own business by claiming for this new machine that it should immediately supersede all existing applications of pneumatic transmission of power for drilling. On the

Jan 1, 1908

Discussion, at the Virginia Beach Meeting, February, 1894, of the Paper of Prof. Posepny. (Trans., xxiii., 197, 587.) Including communications subsequently received. a T. A. Rickard, Denver, Colorado (communication to the Secretary) : The paper of Professor Posepny was printed so short a time

Jan 1, 1895

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non-metallic inclusions seems to be satisfactory and adequate. NATURE AND CONS1lTUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1964