Search Documents

By P. A. Toynbee

An experimental air-slide classifier1 has been applied to the de-dusting of ground dolomite in an attempt to produce a grade of -30 +150 mesh (B. S. Sieves) material from a raw material containing 30-35% of the -150 mesh fraction. Air flows varying between 1.5 and 2.5 cu ft/sec sq ft of screen area were used. The throughput of dolomite was between 80 and 100 lbs/h. inch of screen width. The size analyses of the de-dusted material and of the original dolomite are shown in table at right. The proportions of the +100 mesh material in the feed and in the de-dusted products have been used to calculate materials balances, on the assumption that there is no loss, as dust, of this +100 mesh fraction. By interpolation, it can be shown that a de-dusted product recovery of 68.5% will be obtained at an air flow of 2.13 cu ft/sec sq ft of screen area. The feed material contains 68.5% of +150 mesh material, so that if the de-dusting gave a perfectly sharp cut, the product would contain no material less than 150 mesh. Further calculations based on the size analyses, show that, at an air flow of 2.13 cu ft/sec sq ft of screen air, the -150 mesh fraction in the de-dusted product will fall just below the specified maximum limit of 5%.

Jan 1, 1964

H. M. HOWE, Bedford Hills, N. Y.-One wonders, whether it might not be well to check, by a rather simple and direct way, the inferences that would be drawn from this investigation. Suppose we quench, in these various liquids cylinders of steel, selecting material that is not likely to split in hardening, and then examine their cross-sections micro-scopically. If the cylinder is of any size, you will find a series of concentric bands, a very hard band, a softer band, and a hard band-but it seems that here would be a way of checking the inferences from the cooling curves by comparing these waves of hardness obtained in similar speci-mens quenched in different liquids. One would think that there would be great promise in that way. One's first thought is to quench similar pieces of steel, similarly heated, in different liquids and determine their hardness. I suppose many of us have tried that. We then meet the-difficulty that it is not the most rapid cooling that gives the greatest hardness. There is an intermediate rate of cooling that gives maximum hardness so that you can not by any simple method as that check this cooling method. But it seems possible

Jan 12, 1919

By C. Y. Chen

Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977 (SMCRA), Section 516 (b), requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence cawing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable we of such surface lands, except in those instances where the mining technology wed requires planned subsidence in a predictable and controlled manner.. . ." Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features. This paper also summarizes some measures used to minimize the possibility of damage to structures as a result of subsidence due to underground coal mining.

Jan 1, 1984

In an earlier day, a moderate-sized 600 tpd mine could easily require 60 working faces and might use five supervisors. The miner had a tonnage rate as an incentive and was largely his own boss. With the advent of conventional mining machine crews, the typical pattern of resource used changed radically. The number of work places could be cut by a factor of ten, but supervision only by a factor of somewhere around three, or at most, five. Obviously, supervision was increased. Capital use rose at the same time by a factor of approximately eight. Materials used, such as powder and bits, probably in- creased in both quality and unit cost, too. It certainly required a better-trained man to run the machines, but fewer miners were needed. It is clear that each input factor such as land, labor, capital and management, has changed significantly and it would be foolish to attribute all the gain to improved machines. However, concentration of work was a vital consideration in the change, sketched above, and such focusing of work in fewer areas could not have occurred without high capacity mining machines.

Jan 11, 1968

By Nick Barton, Stavros Bandis

The descriptive term "rock mass" encompasses individual block dimensions ranging from centimeters to many tens of meters. Strength and deformability vary both qualitatively and quantitatively as a result of this size range. A key issue is therefore the appropriate size of the test sample. A large body of test data was reviewed to determine the influence of block size on the displacement required to mobilize peak strength. It is shown that the shear strength and shear stiffness reduce with increased block size due to reduced effective joint roughness, and due to reduced asperity strength. Both are a function of the delayed mobilization of roughness with increasing block size. A method of scaling shear strength and shear displacement from laboratory to in situ block sizes is suggested. It is based on the assumption that size effects disappear when the natural block size is exceeded. This simplification appears to be justified over a significant range of block sizes, but is invalidated when shearing along individual joints is replaced by rotational or kink-band deformation, as seen in more heavily jointed rock masses. Recent laboratory tests on model block assemblies illustrate some important effects of block size on deformability and Poisson's ratio.

Jan 1, 1982

By Atmesh K. Sinha

In spite of the artificial supports which are provided to reinforce the mine roof and prevent failures, roof falls continue to occur very frequently in the mines due to the very unpredictable geological conditions and the dynamic nature of the mining operations. In fact, roof fall is still one of the largest contributor to coal mine fatalities. The design of a roof support plan is often based on arbitrary criterions due to the unpredictable behaviour of the rocks under the mining conditions. The failure of a mine roof which ultimately results in a roof fall and contribute to mine hazards, is caused following a gradual degradation in its physical conditions. A mine roof monitoring system capable of monitoring the rate of deterioration of a mine roof on a continuous basis has been developed and tested in an operating coal mine. The monitor can help to improve and supplement the roof support plans and

Jan 1, 1983

By G. T. Hahn

On the basis of the recommendation of Lovell, Vogel, and Wernick,&apos; Fry&apos;s reagent*2 was recently c) if decoration of the dislocations by carbon or nitrogen atoms is a factor in the etch pitting. Experiments were performed with samples of a commercial 1020 steel, a vacuum-melted iron (C - 10 to 15 ppm, 0 - 20 to 50 ppm, N < 2 ppm), both annealed 4 hr at 1100°C, and a zone-refined iron (C - 3 to 5 ppm, 0 - 10 ppm, N < 1 ppm ) in the as-cast condition. Saomple surfaces were prepared by grinding to 600A grit and electropolishing. Initially, effects of etching the steel with modifications of the basic Fry composition were examined. It was found that increasing the alcohol or HC1 concentratior~ retarded dislocation pitting; reducing the acid content promoted secondary pitting. Cooling the reagent and the sample did not improve the quality of the etch pits. Best results were obtained with freshly prepared reagent modified by increasing the CuC12 content to 15 g. This composition was used in subsequent experiments. Annealed samples were etched 10 to 15 sec; cold-worked samples —2 to 5 sec.

Jan 1, 1962

By Francis B. Foley

THE casting of steel in large molds brings into play all of the undesirable effects that result inevitably from slow cooling. The origin of the molten metal, whether basic or acid open hearth or electric furnace, has little if anything to do with the phenomena involved. If the quantity of molten metal to be cast in a single mold is large enough, there is very little one can do about it-the metal will cool so slowly that &apos;nothing one can do, other than to provide as good feeding as practicable from an adequate reservoir of metal in the sink head, will be of any avail. Recently we have had occasion to cast a 108-in. octagon ingot weighing 545,700 lb, necessitating the combining of metal from three 100-ton open-hearth heats. This is one of the largest ingots ever made. The body of the ingot weighed 448,800 lb, which includes a bottom pool of about 7500 lb of metal, and the sink-head weight was 96,900 lb, or about 18 pct of the total weight.

Jan 1, 1947

By Adelaide Ross Smith

Both history and physical examination are unreliable in the diagnosis of silicosis. In some studies 25 per cent of individuals with silicosis have been found to have no symptoms whatever. The positive physical findings that may be produced by this disease include diminished chest expansion, diminished lung resonance, distant and harsh breath sounds. However, many workmen of a short stocky type have diminished chest expansion without any lung disease. In a study of rockdrillers made by the author more than half of the men without silicosis were limited in chest expansion to 2 in. or less instead of the "normal" 6. In a study of stonecutters the average chest expansion in the negative group was found to be only 2.4 inches. Changes found upon physical examination of the lungs themselves are so inconstant as to be of little diagnostic value. In the studies of rockdrillers and stonecutters already referred to, approximately 25 per cent of those with advanced silicosis apparently had normal lungs. The usual functional tests of lung performance are likewise of little value because of marked individual variation. Average vital capacity will be reduced in a group of silicotics below what might be expected in a group of normals, but certain individuals of the former group may have an entirely vital capacity, giving no indication of the underlying presence of silicosis. It follows that the X-ray examination is absolutely indispensable in the diagnosis of this disease. X-ray findings characteristic of silicosis have been described innumerable times. They consist essentially of a mottling of the lung fields due to the presence of fibrous nodules which develop as a reaction to the presence of the irritant silica.

Jan 1, 1934

The failure of finely-divided sulfide particles to respond to flotation has resulted in a significant loss of our natural resources. As mentioned by Professor Arbiter, the overall recovery of copper from porphyry copper ores is generally between 80 and 85 percent. The recovery of copper sulfides from these ores is about 90 percent, the difference in these recoveries being due to failure of oxide copper minerals to respond to flotation. The 10-percent loss of sulfide copper has not been studied. Losses are known to be in the fractions finer than 74 microns, but the sizes that are not responding to flotation have not been established. In the case of molybdenite, however, it is known that particles finer than about five microns are not recovered. Work in other systems, notably the hematite-quartz system, has shown that good flotation of very fine particles from natural ores is possible (1, 2). The size distribution of one ore that was researched is given in Table 1, and as shown, approximately 50 percent of the ore was finer than 10 microns. Flotation experiments were conducted with this ore, which contained 45 percent iron, utilizing octyl hydroxamate as collector and without any desliming (1). The results of these experiments are presented in Table 2. From the standpoint of mechanisms of collector adsorption, similarities exist between those occurring in the hydroxamate-hematite system and many xanthate-sulfide systems. .This is, multilayers of ferric hydroxamate are present on hematite under flotation conditions (1,3).

Jan 1, 1979

By Larsen. Edward P.

The principle of "bed blending" in the agglomeration of materials is about 56 years old, but de- spite all education via technical papers, operating reports and results from functioning installations, the concepts of blending are still somewhat vague. Confusion exists between "mixing", "blending," and the basic role of each. The terms "blending" and mixing" are often used interchangeably, yet they describe two different processes. As properly understood and applied, a blend is a combination of different varieties of material which produces a desired quality, or the mingling of different elements to form a harmonious whole. In other words, blending is a process of combining granular materials by mechanical means, wherein the final product, or a portion thereof, must contain an exact proportional amount of every one of the several different materials which contributed to the mass and wherein all particles are so thoroughly intermingled with each other as to have lost their individual identities and become a part of the whole so that when a portion of the blend is taken at any time it will be substantially identical, chemically and physically, to any other portion taken throughout.

Jan 1, 1962

Committee on Reduction and Refining of Copper............ 3 A.I.M.E. Officers and Directors.................... 4 Preface. By C. R. Kuzell....................... 7 Career and Achievements of James Douglas. By Arthur L. Walker. . 9 PAPERS Smelting 1. Reverberatory Smelting Practice History of Reverberatory Smelting in Montana, 1879-1933. By Frederick Laist..............................23 Reverberatory Smelting of Raw Concentrates at the International Smelter, Miami, Arizona. By P. D. I. Honeyman (With Discussion)...... 88 Development of Gun-feed Reverberatory Furnaces at Garfield Plant of American Smelting and Refining Company. By R. A. Wagstaff (With Discussion)........................99 An Experimental Combination of Shaft Roasting and Reverberatory Smelting. By Frederick Laist and J. P. Cooper (With Discussion).... 104 Forms of Copper Found in Reverberatory Slags. By Royal B. Jackman and Carle R. Hayward (With Discussion).............111 2. Converting Practice Development of Copper Converting at Butte and Anaconda. By William Kelly and Frederick Laist...................122 Developments in Converting Lead and Copper Matte at Tooele. By B. L. Sackett.............................132 Messina Stationary Basic Copper Converter. By R. G. Knickerbocker (With Discussion)........................140 Smelting Copper Concentrates in a Converter. By George E. Beavers. 149 Sulfuric Acid from Converter Gases. By George E. Beavers......151 Development of Monolithic Tamped Periclase Converter Linings at United Verde Copper Company Smelter. By F. H. Parsons (With Discussion) . 153 3. Descriptions of Plants The Noranda Smelter. By W. B. Boggs and J. N. Anderson......165 Smelting Operations at Roan Antelope Copper Mines, Limited. By Charles R. Wraith.......................202 4. Waste-heat Boiler Practice Copper-refinery Waste-heat Boilers at Great Falls Reduction Department, Anaconda Copper Mining Company. By E. S. Bardwell......225

Jan 1, 1934

By J. D. Verhoeven

In a recent study1 this author has investigated the effect of an electric field upon the solute redistribution accompanying solidification of Sn-Bi alloys. It was concluded that the primary effect of the electric current upon the solute redistribution resulted from electrotransport within the liquid boundary layer at the solid-liquid interface. In order to maximize the electrotransport effect all of the experiments were conducted at the highest current densities experimentally attainable. It was found that these high current densities produced considerable convective mixing within the liquid metal. This mixing reduces the boundary layer thickness and consequently reduces the effectiveness of the electric field in producing solute redistribution. Consequently, it is quite possible that the condition of maximum achievable current density would not correspond to maximum solute redistribution. It may be that, as the field intensity is increased, a point is reached where the additional solute redistribution from the increased electrotransport is more than offset by the decrease in solute redistribution resulting from the increased mixing in the liquid. In order to check this possibility the effective distribution coefficient has been determined as a function of current density in a series of experiments. The experiments were conducted on 6.6 at. pct Bi

Jan 1, 1968

By H. M. Fisher, R. E. Snow, S. C. Sun

RAPID colorimetric estimation of the amount of transparent minerals has been applied successfully to instream mill products at the cryolite flotation plant of the Pennsylvania Salt Mfg. Co., Na-trona, Pa. Apparatus used was a Bausch & Lomb monochromatic colorimeter. The optical assembly of the colorimeter, shown in Fig. 1, passes light from a 6-v, 32-cp, prefocus incandescent lamp through two condensing lenses, a heat-absorbing filter, an aperture-control diaphragm, an interference filter, and a sample container. The light finally strikes a barrier-layer photocell and the output current of the photocell is measured by a galvanometer. The engraved index line of the collective lens, located between the lamp and the galvanometer, is imaged upon the transmission scale of the colorimeter by the galvanometer mirror. Reflected light from the galvanometer mirror, the position of which is determined by the output current of the photocell, enables reading of percent transmission throughout the mineral sample being tested. The colorimeter, Fig. 1, was standardized as follows: 1—The colorimeter was&apos; connected to a Sola constant voltage transformer, A, of 6-v output operated from a 110-v ac supply. 2—Turning the toggle switch, C, illuminated the transmission scale, B, and the control knob, D, was adjusted with a blank in the optical system until the hairline on the scale read zero. 3—A No. 430 interference filter, E, was inserted into the filter channel, F. 4—A test tube, G, containing 7 cc of distilled water was pressed into the sample space, H, and the fine adjustment knob,

Jan 1, 1955

By Harvey S. Chase

During the recent great depression in iron, little has been done in the magnetic separation of iron-ores; and previous to the present decade the art was in its infancy, so that there were few, if any, successful separators on the market, and but scanty practical data could be obtained as to the industry itself. Moreover, the recent development of the great Mesabi Bessemer beds, coincident with the intense depression in business, has discouraged active attempts to solve the problems presented in the crushing and separation of the refractory magnetites of the South. Experiments have been carried on, however, upon a practical scale in separating these ores magnetically, at the well-known Cranberry mines, in Mitchell county, N. C., with results which are encouraging. The magnetites of the Blue Ridge, in the South, have been known, and the soft ores of the region have been used in Catalan forges, since very early times. The original settlements in East Tennessee were made along the Watauga river by Daniel Boone, William Bean, John Sevier, and other stalwart pioneers; and this valley lies parallel with the " Cranberry " lead, which is undoubtedly the most celebrated and the most extensive deposit of workable magnetic ore in the Southern States. This lead I have personally traced along the outcrop, be-

Jan 1, 1896

By C. M. Myrick

The following notes are submitted in the belief that they may interest some of the many owners of mall water-power plants, so generally used in mining-work throughout the West. A small and somewhat primitive quartz-mill was taken over by a leasing company, and a 10-stamp battery was installed. Originally, power had been furnished by a Pelton wheel; but, since the supply of water depended on the rate at which snow was melting 011 the mountains, a steam-plant had been added to help out during cold spells. This auxiliary plant was antiquated and expensive to operate, and, soon after starting up the remodeled mill, it broke down completely; so that it became neceseary to get all the power possible out of the Pelton wheel, with its ever-varying water-supply. The pipe-line, about a quarter of a mile long, was made up of assorted sizes, from 7 to 11 in. in, diameter; and, since it was buried deep under snow, there were no data from which to calculate the theoretical size of the nozzle. The stream being at this time at a low stage, it was important to make the most efficient use of the available water. This was done by using a nozzle large enough to pass the whole supply—taking care, however, to limit the size so as not to lower the water-level in the tank at the head of the pipe-line. As the weather became warmer, the nozzles were gradually enlarged to meet the increasing volume of water; but a point was finally reached where further enlargement only gave decreased power. Evidently the loss from friction had more than balanced the gain from the increased flow through the pipe. However, the area of nozzle that developed the maximum power from the pipe-line had been found. This was used; and the surplus water was allowed to run to waste at the head of the line.

Jan 1, 1913

By Harry A. Roe

THE power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. [ ] The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1937

By J. D. Lubahn, R. P. Carreker, J. G. Leschen

The formation of slip bands in crystalline solids undergoing plastic deformation has recently been treated as a problem of nu-cleation and growth.&apos; A simplified theory was developed and shown to be qualitatively consistent with certain experimental observations reported in the literature, such as the frequent failure of slip bands to traverse the entire crystal, the effect of specimen diameter and temperature on the yield stress, and the occurrence of incubation periods in the deformation of suddenly loaded crystals. The theory further predicts the appearance of transients in the rate of strain of a crystal when the applied stress is suddenly changed from one constant value to another. A transient consists of a discontinuous change in the strain rate followed by a gradual approach to a steady-state value. Such transient behavior apparently has not been recognized in previous experimental work. The preliminary experiments reported in the present paper were undertaken to confirm the existence of the predicted transients and thus to determine whether a more detailed treatment of the nucleation theory of slip might be theoretically and experimentally fruitful. Experimental Procedure A simple creep apparatus was assembled as shown in Fig I. Very little insulation was used on the furnace in order to facilitate rapid changes of temperature. Temperature was measured with a thermometer placed in the center of the furnace and was controlled by adjusting the Variac setting. The specimens were cold-headed in split-cylinder grips. The strain was measured as total elongation by a dial gauge sensitive to I/I0,000-in movement of the weight pan. Since the specimen gauge lengths were

Jan 1, 1949

By F. W. Robinson

THE temperature coefficient of electrical resistance of pure metals is high and therefore the resistance increases rapidly with rising temperature. In 1871, Siemens suggested the use of this property as an accurate means of temperature determination. Owing to practical difficulties, particularly the contamination of the metal and consequent permanent change in its resistance and its resistance-temperature relation, this method fell into disrepute as a practical standard until revived later by Callendar and Griffiths, and subsequently by Holborn and Wien, all of whom showed that the earlier difficulties were not inherent in the method but incident to the mode of protection of the resistance coils. Following .the work of these investigators, the problem of temperature measurement by this means has been the subject of careful study and has now assumed an importance second only in practical adoption to the thermo-electric method. It is generally recognized, both here and in Europe, that the standard temperature scale should be the thermodynamic as it permits the evaluation of high temperatures on the basis of the radiation laws of Stefan and Bolzmann, of Rayleigh, and of Wien and Planck, on a scale consistent with that obtained by means of the gas thermometer at low temperatures. Lord Kelvin showed that only. a very small correction, amounting to about +0.7° at 1000° C.-almost within the limits of experimental errors-is necessary to adjust the constant-volume nitrogen thermometer to the ideal thermodynamic scale.

Jan 9, 1919

By Robert Livermore

THE Smuggler-Union mine is in the upper San Miguel mining district near Telluride, Colo., and the group of claims now forming the property were first worked in 1875. Development was slow until the completion of the railroad in 1890, when it pro- ceeded rapidly. In 1896 four hundred stamps were dropping in the district, the production was $3,000,000. A geologic section of the country rocks, where ex-posed by erosion from the valley at 8700 ft. to the sum-mit at 13,500 ft., shows the sedimentaries made up of flat-bedded sandstones and conglomerates, of the Jura-Trias, superimposed at 9700 ft. by a series of bedded rocks of igneous origin, andesites and andesite breccia. These rocks extend 3000 ft. to the rhyolite capping, largely fragmentary, which occurs at 13,000 ft. The ore horizon is, so far as known, contained in the 3000 ft. of&apos; andesite and breccia. The Smuggler vein is a fault fissure which, with its extension to the north, the Humboldt vein, contains one of the longest continuously mined orebodies in the world. The length of the orebody so far developed is approximately 9000 ft. The width of the valuable part of the vein is, however, narrow, 3 ft. being the average, and the depth to which it has been worked up to the present is 2500 feet. There are several crossing and branch veins, all of which have been more or less productive. Of these, the so-called Flat vein, discovered in 1915, with its pro-duction of nearly 2,000,000 tons, has been the most important. This vein joins the Smuggler at an acute angle in the northern section of the property. North of the junction the two veins lie side by side and form an orebody of importance which gives promise of exten-sion with depth. The valuable metals of both the Smug-gler and Flat veins are gold, lead and silver. In the former silver is more important than lead, and the reverse relation holds in the latter.

Jan 3, 1928