Search Documents

By W. R. Phibbs

THE blast furnace of the Columbia Steel Corpn., at Ironton; Utah, was put in blast April 30, 1924, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PER CENT. Moisture 3.90 Volatile 39.00 Fixed carbon 51.10 Ash.... 6.00 Sulfur : 1.07 The analysis of the coke is: PER CENT. Volatile 0.55 Fixed carbon :...:.::: :..:.:: 89.70 Ash 9.75 Sulfur 1.05

Jan 1, 1928

By P. K. Kaiser, C. Mackay

A circular shaft with a diameter of 6m was excavated by the conventional drilling and blasting method to a depth of 235m through 60m of glacial till, 1 Om of water bearing basal sand, 1 1 Om of clay shale (Bearpaw Formation) and finally a strata of coal, mudstone, siltstone and sandstone (Oldman Formation). The lined shaft was instrumented at three levels by multipoint extensometers to determine the displacement field near the shaft bottom, embedment strain gauges to measure the strains in the liner and IRAD-stress change gauges to observe the radial and tangential stress changes in the rock mass. The data from these gauges were used to determine the in situ stress field. An attempt to measure in situ stresses by overcoring was also made at a higher elevation. The performance of the shaft and its support was then evaluated by use of the "Convergence-Confinement Method". For this purpose the measurements of stress changes and displacements were combined to determine by extrapolation the displacements ahead of the shaft and after the liner installation. The convergence curves calculated in this fashion were then used to evaluate the performance of the cast-in-place concrete liner and of an alternate shotcrete shaft support system.

Jan 1, 1983

By C. O. Babcock

In this Bureau of Mines report, the authors present the results of laboratory tests on the burst proneness of coal. Many researchers have studied the violent breaking of large coal masses in underground mines, called bursts, but the causes remain uncertain. They have often assigned to geology and gas pressure the causative roles. The objective of this work is to show that stress can produce bursts in many coals if constraint is necessary for pillar survival and is suddenly lost. We tested coal samples from 15 mines, in 11 coal seams, in six states in the laboratory, and 13 were made to burst. These bursts were produced in several ways, but segmented steel platens were used in the tests reported. Two parameters analogous to the momentum and kinetic energy were used to rank the burst proneness of the coals tested. Tangential strains over the lower surface of the model coal pillar were measured to reveal a periodic slipping prior to the burst. High-speed motion pictures (350 frames per second) reveal the burst behavior in slow motion. We propose a modified Mohr-Coulomb stress-failure criterion to describe the burst behavior. When the horizontal constraint is suddenly lost with little change in the vertical stress, the Mohr stress circle increases in size dynamically, exceeding the static failure condition. When the inertia of the coal mass is overcome, a burst occurs. We conclude that most coals can be made to burst and that such bursts can be expected in mining at increasing depths.

Jan 1, 1984

By G. L. Spencer

There is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and .higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiff-ness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges. Materials Used for High-silica Retorts The materials used in the manufacture of high-silica retorts at East St. Louis are fireclay, grog and silica flour. Analyses are given in Table 1. The fireclay comes from the St. Louis district. The grog consists of clean firebrick culls, and the silica flour, a very high-grade material, is purchased in the form of a flour that has been ground through 140 mesh.

Jan 1, 1931

INTRODUCTION AND SCOPE This chapter is intended as a brief review of the mathematics of compound interest and of the meaning of time equivalent money. In order to make valid economic evaluations of various investment alternatives, it is important that they be analyzed on an equivalent basis, taking into account the time value of money. Compound interest has been said to be one of the eighth wonders of the world. Certainly compound interest is a fact of life in today's economy. Whenever we deal with money over time-investments, earnings, savings, loans, etc.-we are immediately confronted with the principles and effects of compound interest. In such an environment it is necessary to be able to determine time value equivalence of various sums of money received or paid at different dates. It follows that all future payments or series of payments that would repay a present sum with interest at a stated rate can be said to be equivalent with each other. Equivalence, then, is a function of the interest rate. MATHEMATICS OF COMPOUND INTEREST FACTORS In order to develop mathematical formulas for various time value equivalence of compound interest we will use symbol designations: P is Present or principal sum of money; usually refers to value at time zero. F is a single sum of money at some designated future date. R is The amount of each payment in a uniform series of equal payments made at the end of each period. n is Number of interest compounding periods (may represent annual, semiannual, quarterly, or even daily periods). i is the period compound interest rate. Figure 20-1 illustrates the increase of princi-

Jan 1, 1980

F. J. DE WILDE, Galena, Ill. (written discussion *) .-As it is impossible to spare the time for a lengthy discusson of this excellent paper, I am dwelling only on points where either the information is not clear or opinion differs radically from that of the authors. On page 1218, relative to oil rock, the authors state that the presence of oil rock is always taken as a favorable indication of proximity to ore. As thick, highly carbonaceous, oil rock has been found quite often in isolated patches outside of the district proper, the mere presence of oil rock is not always an indication of the propinquity to ore deposits. Regarding glass rock, I agree with the authors, that, generally speak-ing, sphalerite in the glass rock is spotty; however, they fail to mention that nearly all mines contain more or less ore in the glass rock, the usual location being near the toe of the pitch. On page 1220, they say that disseminated deposits are only found in, or close to, the oil rock. To refute this statement, I refer them to a typical disseminated deposit situated at the Adam and Eve shaft of the Frontier Mining Co. This deposit is located in the central horizon of the Galena dolomite, that is, in those sedimentaries containing flint nodules. Perfect crystals of sphalerite are found disseminated through-out the rock, and are commonly known by the miners as strawberry jack. I believe all top runs, or upper deposits as described above, should be classed as disseminated; physically the ore makes its occurrence in just such a manner.

Jan 11, 1919

By Charles C. Hall

The following procedure in estimating mineral oil when mixed with vegetable or animal oils, is the result of a long series of cxperiments based on the method suggested by Sir William Thompson and Mr. A. H. Allen, in a paper read before the Royal Society.* Four to five grams of the oil under examination are weighed out into a porcelain capsule of 75 C.C. capacity. Thirty C.C. of a 10 per cent. solution of potassium-hydrate in alcohol are added, and the capsule covered with a watch-glass is placed in a water-bath heated to about 93' C. The mixture of oil and alkali should be stirred frequently, and after three-quarters of an hour it is boiled with stirring. This will secure the complete saponification of all the vegetable or animal oil. After the boiling has been continued some time, and most of the alcohol is expelled and a thick scum of soap forms on the surface, a little bicarbonate of soda is added to convert the excess of caustic alkali into carbonate. When the contents of the capsule have become pasty an equal bulk of fine, clean sand is stirred in. This makes the soap granular, and facilitates the removal of the last traces of alcohol. The capsule is now heated for two hours more on the water-bath. After cooling, the contents of the capsule are transferred to a short-necked funnel, having a thin plug of asbestos, and washed with petroleum-ether, or some other light petroleum spirit. The ether dissolves out the mineral oil from the soap, and is best collected in a quarter-liter flask having a short neck. The ether can be applied conveniently and effectively by a small washbottle. Care must be taken to effect a complete removal of the oil

Jan 1, 1883

By Howard W. Dubois, Charles T. Mixer

Only within the past few years have chemists recognized the importance of the fact, that comparatively large amounts of phosphorus may occur in the siliceous residue left from the acid treatment of iron-ores. We know of one case in which an ore contained about three times as much phosphorus in the insoluble, as in the soluble, form. It was disposed of at a premium, as an exceptionally high-grade Bessemer ore containing 0.010 per cent. of soluble phosphorus, while the insoluble phosphorus brought the total amount up to 0.040 per cent. The magnetite and specular hematite of the Lake Superior districts and the fine ores of the Mesabi range, as a rule, contain very small amounts of insoluble phosphorus. But the mining of the soft hematites and the progressive lowering of the phosphorus-limit in a strictly Bessemer ore, have combined to make the determination of insoluble phosphorus one of the routine-requirements in all analyses of Bessemer ores. The insoluble phosphorus is understood to be that pbosphorus which cannot be extracted by boiling hydrochloric acid of 1.1 specific gravity. The time given for the extraction of the soluble phosphorus will vary, of course, according to the nature of the ore. In ordinary practice the boiling is continued until the residue is white or only very slightly tinged with ferric oxide. This ordinarily takes from half an hour to an hour. The prolonged boiling of ores known to contain considerable quantities of insoluble phosphorus has failed to extract any appreciable amount of additional phosphorus. Very fine grinding and subseqnent sifting through bolting-cloth has not increased the extraction. These statements represent the re-

Jan 1, 1898

By John Cobb

THE attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinations of ,the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia, at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal, and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in another way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 3, 1925

By Harold Rabling

The following notes are taken from results obtained on a standard 25-ft. Hancock jig1 tested during regular operation in the Bonne Terre mill of the St. Joseph Lead Co. The object of the tests was to determine the conditions for most effective work, and the nature of products that could be made. The material treated was sized between 9-mm. and 2-mm. round-hole screens, and was constant throughout the experiments. Three products were made, concentrates from the first three hutches, middlings from the fourth and fifth, and tailing from the sixth. The middlings were crushed in one pair of Allis-Chalmers Style B, 30 by 14-in. rolls, and elevated with the original ore to the 2-mm. screens, oversize of which formed the jig feed. While this arrangement was very simple, it gave rise to undesirable crowding of the circuit. Table 1 shows tonnage and assay values of the jig feed and products at the beginning of the experiments, and brings out the excessively large amount of middlings, comprising 63.3 per cent. of the total material fed to the jig. The rolls, being heavily overloaded, did very little crushing, a screen analysis of the product showing that only 27 per cent., or 128 tons, was crushed fine enough to pass to the tables. The remaining 347 tons returned to the jig with 400 tons of original ore. At .times, this overcrowding became much worse, and the tonnage in circuit grew to enormous proportions. It became imperative

Jan 1, 1918

By Martin Coryell

EHRENBERG was the first to publish and direct attention to the peculiarities of the diatomaceous deposit of Richmond; but how and by whom he was supplied with the material for his microscopical investigations, is not generally known; but we may presume W. B. Rogers, formerly State Geologist of Virginia, furnished the material, and may have given the geological position or horizon. O£ these facts we have no available evidence, nor have we any estimate of the thickness of this stratum of diatomaceous or infusorial earth. At the request of a member of this Institute, I have investigated the subject, and offer the following facts as the result, derived principally from information supplied by Mr. John Ott, of the Southern Fertilizing Company, Dr. William Taylor, State Chemist, C. Peticolas, microscopist, Captain Robert H. Temple, civil engineer, Major C. M. Bolton and Mr. C. M. Smith, civil engineers, and formerly engaged in constructing the tunnel under Church Hill, in Richmond. The city of Richmond is generally described as being built on seven hills. This is not the fact, geologically speaking. Originally, there was an immense plateau of land, about two hundred feet above tide, in which a deep excavation was made from the west to east by the James River cutting down to the granite. Opening southward and meeting the valley of the James are various ravines and gullies, in the principal of which are Shockoe and Gillies Creeks. The formation is tertiary, subdivided into all the classified divisions, but at the present moment no one has been found to make this section a special study. Rogers's early classifications and diagrams, with all their imperfections, are the only published records, and the printed editions are long since exhausted. The city of Richmond is really situated in these ravines of the James, Shockoe, Gillies, and their connections. The profile marked A, Plate V, represents the section of the plateau

Jan 1, 1876

By H. C. George

At the annual meeting of the Institute in February, 1927, we had a comprehensive discussion of Petroleum Engineering Education. This discussion covered basic training and prerequisites, laboratories and equipment, graduate courses, availability of lecturers, geological engineering, petroleum production engineering, refinery engineering, transportation engineering and economics and management. However, there are several phases of petroleum engineering education, which many members of the Institute felt should be further discussed at this year's meeting. The first was expressed by me in a letter to those participating in the written discussion, from which I quote as follows: "We fell that the question of handling engineering graduates who enter the petroleum industry should be thoroughly discussed. "During the first five years after graduntion from college, how can these young men be best trained to be of the greatest service to the industry and at the same time do work which will be interesting and of a character which will make them feel that they are accomplishing something and making progress leading toward personal advancement?" Both the written and oral discussion would indicate three groups of opinion; first, those who advocate letting the young engineers go into the industry and take care of themselves without any supervision, direction, or guidance; second, those who advocate the taking of young engineers into the industry and letting them go through all the steps that any laborer or any other mian without a technical education would take, but with some supervision, and third, those who advocate that young cngineers should be given special training for several years after entering the industry. Of course all of these different groups are found in rnost of our industries. The Doherty training school of the Empire Gas & Fuel Co., finds its counterpart in the practice of the Gcneral Electric and Westing-house companies in the electrical industry and the Baldwin and Brooks Locomotive works in mechanical engineering.

Jan 1, 1928

By Martin Coryell

Ehrenberg was the first to publish and direct attention to the peculiarities of the diatomaceous deposit of Richmond; but how and by whom he was supplied with the material for his microscopical investigations, is not generally known; but we may presume W. B. Rogers, formerly State Geologist of Virginia, furnished the material, and may have given the geological position or horizon. OF these facts we have no available evidence, nor have we any estimate of the thickness of this stratum of diatomaceous or infusorial earth. At the request of a member of this Institute, I have investigated the subject, and offer the following facts as the result, derived principally from information supplied by Mr. John Ott, of the Southern Fertilizing Company, Dr. William Taylor, State Chemist, C. Peticolas, microscopist, Captain Robert H. Temple, civil engineer, Major C. M. Bolton and Mr. C. M. Smith, civil engineers, and formerly engaged in constructing the tunnel under Church Hill, in Richmond. The city of Richmond is generally described as being built on seven hills. This is not the fact, geologically speaking. Originally, there was an immense plateau of land, about two hundred feet above tide, in which a deep excavation was made from the west to east by the James River cutting down to the granite. Opening southward and meeting the valley of the James are various ravines and gullies, in the principal of which are Shockoe and Gillies Creeks. The formation is tertiary, subdivided into all the classified divisions, but at the present moment no one has been found to make this section a special study. Rogers's early classifications and diagrams, with all their imperfections, are the only published records, and the printed editions are long since exhausted. The city of Richmond is really situated in these ravines of the James, Shockoe, Gillies, and their connections. The profile marked A, Plate V, represents the section of the plateau

A USEFUL and very ingenious idea was surely that of the inventor of AN a short way of extracting gold and silver from the sweepings of all those arts that handle them as well as every particle that smelters of ores might have left in the slags, and also that in some ores themselves. This is done without using great labor in smelting but by the sole means and virtue of mercury. To do this, first make a large bricked pan of stone or wood and arrange a millstone inside which rotates in the hollow of this pan like that of a flour mill. In the hollow of the pan put some of your material containing gold after it has been crushed well in a mortar and then washed and dried. Grind it in the said mill, moistening it meanwhile with vinegar or water in which sublimate, verdigris, and common salt have been dissolved. Then enough mercury to cover these materials is poured over them. They are agitated inside for an hour or two, by turning the mill either by hand or with a horse, depending on the device that you have arranged. Remember that the more the mercury and the material are rubbed together in the mill the more it can be believed that the mercury absorbs the substance that the materials contain. Finally, thus prepared, the mercury is separated from the earthiness with a sieve or by washing and thus the mercury is retrieved. Then, make it rise with a little cucurbit or pass it through a purse and there will remain at the bottom the gold, silver,. copper, or whatever metal you placed in the pan under the millstone to be ground. Wishing to know this secret, I gave to the one who taught it to me a ring with a diamond worth twenty-five ducats, and I also pledged myself to give him the eighth part of whatever profit I should gain from this

Jan 1, 1942

By F. L. Sizer

THE mining regulations of British Columbia and Mexico present some features which might well be copied in the United States, if we are to have a complete revision of the laws governing mining titles. 1. First and foremost is the "square" location, which would mean the abolition of extralateral rights. This is a condition in both of the countries above named which has seemed to work no hardship upon any one, and certainly the limitation of underground rights by vertical planes through all lines makes a locator's rights clear. In view of the long and costly litigation which has involved so seriously many of our most important mining districts, it would seem to be the part of wisdom to avoid a repetition of similar trouble on titles of lode mining claims, by the enactment of a law similar to that in force in British Columbia. Objections have been raised by representatives of English companies to the investment of large amounts of money in mining operations in the United States, because of the insecurity of title under the present apex law; and the statement has been made to me personally by one of the largest English operators, that he would never again consent to the purchase of mines in the United States, preferring Mexico with all its revolutionary troubles to the danger of encroachment upon his underground rights by an unscrupulous neighbor. Without going into further argument as to the desirability of the "square location," it should be sufficient to say to those who are inclined to "let well enough alone." and still stick to the "law of the apex" that there have never been any serious objections raised to this feature of the square location in either British Columbia or Mexico. There are well founded and logical reasons for abandoning the doctrine of extralateral rights since it is so difficult of interpretation; the most natural substitute being a law similar to that of British Columbia, giving to each locator an area 1,500 ft. square.

Jan 3, 1914

By N. Malakouti, R. H. Whipp, O. A. Kuby, R. M. Smailer

A detailed description of the development of the FIOR process (Brown, Campbell, and Saxon, 1966) and, subsequently, other technical papers related to the operation and start up of the FIOR plant (Violetta, 1975; Whipp, 1980) are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Co. during the 1950s and 1960s. The facility in Venezuela was designed and constructed by Davy McKee, with plant start-up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of ownership being private capital. The FIOR process is well suited to utilize the naturally occurring iron ore fines of the Cerro Bolivar and San Isidro iron ore deposits located less than 100 km (62 miles) south of the plant site. Availability of natural gas within 150 km (93 miles) to the north, and a location bordering on the confluence of the Caroni and the Orinoco Rivers makes for an ideal geographic site. Feed stock to the FIOR plant consists of naturally occurring iron ore fines from these ore bodies, which are screened to -6mm (-0.2 in.) prior to drying in the ore preparation plant. A simplified flow plan is shown in [Fig. 1]. The dried ore is then transferred to the top of a structure containing four fluid-bed reactors located above one another so the mineral may flow from one reactor to the next by gravity. A reducing gas containing 90% hydrogen is made by steam reforming of natural gas, a CO shift

Jan 1, 1983

By Thomas M. Drown

IN the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down-accurately to one inch section. These were immersed in a large wrought-iron pot full of molten sodium carbonate made by fusing the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling was broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By Thomas M. Drown

In the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be .found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down 'accurately to one inch section. These were immersed in a large wrought-iron pot full of molteu sodium carbonate made by fusiug the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling mas broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

Jan 1, 1944