Search Documents

By R. C. Mahon

THE importance of ground water control in glacial drift overlying mines is widely recognized. Adequate handling of the problem results in consider- able saving in overall pumping costs, as the cost of pumping the larger quantity of water under low heads from surface wells is more than offset by the decrease in the quantity of water to be pumped from the mine under high heads. Eliminating or partly reducing seepage of water through the ledge reduces moisture content of the ore, a factor especially important in iron ore mines, where a reduction of 1 pct in moisture effects a very material saving. An important though indeterminate saving is also brought about by the elimination of water in the working places underground. The Homer and Wauseca mines of Hanna Coal & Iron Co. at Iron River, Mich., cover 480 acres. When these mines were started it was possible to operate on only one 40-acre tract, as the depth of water over the remainder of the property was too great to permit operation. Although the average depth of the ground water over the area being mined at that time was less than 50 ft it was necessary to pump 1200 gpm from the mine, the greater part from a depth of 750 ft. The slate footwall and graywacke hanging wall are almost impervious, and it was apparent that seepage into the mine was mainly through the iron formation in which the orebodies were located. Analysis of the water in the iron formation showed it to be of the same character as that in the glacial drift, while the water in both walls was heavily mineralized, also indicating that the water passed much more freely through the iron formation.

Jan 6, 1954

By Bernard Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to be porous. In- [ ] deed, sponge iron, prepared by reduction of the oxide in a reducing gas, is generally accepted as quite porous, with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig I shows commercial tungsten powder magnified at 10,000X by the electron microscope,1 both etched and unetched. In an earlier paper by one of the authors,2 the existence of pores in tungsten powder [ ] was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these pores are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than 100 A, and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1948

By W. H. Hoffman

During the autumn of 1891, several heavy blasts (each throwing down some 3000 tons of ore) were made on what is known as the Theall side of these mines. Immediately after one of these blasts, the writer found that at least one-third of the ore was largely impregnated with pyrites, and besides this, fully 15 per cent. of the entire blast was composed of irregular lumps of magnetic pyrites. This was a revelation wholly unexpected, as previous examinations by many experts had failed to disclose any such quantity of sulphury ore. Over the center of the Theall tunnel there suddenly appeared a perfect keystone, as it were, of pyrites, 3 feet wide at the arch of the tunnel, 13 feet ride at the top, and 20 feet high. This keystone pinched out in February, 1892; but in that month large blocks of pyrites were more plentiful on or near the western wall, and these deposits extended the entire height of the workings, some 43 feet. The second blast in November, in the face and over, and on each side of the tunnel, was far more surprising. The whole cross-section it exposed was thickly interspersed with layers of magnetic pyrites, ranging in thickness from 10 to 24 inches, and quite irregular in form, while all of the ore carried much more than the usual amount of sulphur in the non-magnetic pyrite. One hundred and fifty-five tons from a portion of this breast (western side), showed the following composition upon sampling and analysis: Per cent. Metallic iron,...45.080 Phosphorus,..........304 Sulphur,...........23.510 And the balance of the blast showed: Per cent. Metallic iron,.....• 33.210 Phosphorus,...........349 Sulphur,.......... 6.680 vol. xxI.-33

Jan 1, 1893

By R. G. Baughman

With the constantly increasing sales competition, coal to be sold today must meet the test of quality in every respect. The producers must be able to make all marketable sizes that will meet such general requirements as follows: 1. Ash content must be consistently low, depending upon the use to be made of the coal. 2. Sulfur content must be controlled accurately according to requirements. 3. All sizes must be positively free from visible impurities. 4. Free moisture of washed sizes must be reduced to a minimum. 5. The freezing of wet coal in cars must be prevented. 6. The percentage of fines in small mixed sizes must be controlled to give the uniform and proper combustion when used on various types of automatic stokers. 7. The undersize particles or degradation caused by handling must be kept to an absolute minimum in all sizes loaded. Many difficulties may be met in bringing any particular coal to meet these quality requirements, because the extent to which the quality of a coal may be controlled is determined largely by its physical characteristics. Preparation of an Impure Coal Bed The application of modern and scientific methods in the controlled preparation of bituminous coal from a bed in the mid-western field will illustrate the results that can be accomplished by adequate preparation: The bed referred to contains coal inherently excellent as to low ash and other desirable characteristics; in fact, the coal itself is one of the best in the field. It is, however, divided into four layers by dirt bands of soft shale 1 to 2 in. thick. It also contains much sulfur in the form of sulfur lenses and laminated sheets. Horsebacks or rolls varying from 6 in. to 12 ft. in width are encountered in the mining of the bed and heretofore have rendered it practically unworkable. The mines operating in this

Jan 1, 1931

By E. Cortese

PHOSPHATE occurs in many places in Egypt,. in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the cancel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following, that track, after, having crossed the watershed, underlain by rocks like granite, serpentine, porphyry and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at' Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Auressensis Coq. sp.- R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismäely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconformably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 2, 1918

By L. S. Panyity

The State of Ohio is among the pioneers in the production of oil and gas. Numerous anticlinals, such as the Macksburg, Cow Run and Newport, have been thoroughly developed, and the pools found in connection with them are quite in accord with the structural theory. Numerous oil and gas pools found in the Berea sand, however, demand a different explanation. The study of these pools belongs to the sub-surface geologist, as it is possible to understand the factors controlling "off-structure" accumulations only after a careful study of well records. By carefully analyzing the various conditions over a large territory, it is possible to understand the otherwise meaningless mass of data that one may have at hand, and put it into tangible shape, from which various conclusions may be drawn. The territory here discussed includes Belmont, Guernsey, Muskingum, Noble, Monroe, Morgan, Washington, Athens and Meigs counties, containing the majority of the prolific oil and gas pools of the Carboniferous system in southeastern Ohio. The general dip of the strata is to the southeast, the entire territory lying on the northwestern flank of the Appalachian geosyncline. The best known oil- and gas-producing horizon in the territory is the Berea sand, which lies near the lower part of the Mississippian, with the Sun-burry shales (the coffee-shales of the driller) above, and the Bedford shales below it. The Bedford is underlain by the thick Ohio shales. The Ohio and Bedford contact is considered to be the dividing line between the Carboniferous and Devonian systems. The Berea is one of the most persistent of recognizable oil and gas horizons; its outcrop has always been found in its expected place, and it has always been penetrated whenever the drill went deep enough. It is not expected, however, even of the most uniform formations, that no lithological variations should occur, and the Berea is no exception. Nevertheless, there appears to be a certain regularity in its variation, the main features of which directly affect the accumulation of petroleum.

Jan 1, 1920

By K. L. Meissner

IT is well known that the so-called pure aluminum contains noticeable amounts of impurities, chiefly iron and silicon, and many investigators have studied the forms in which these impurities exist. Hanson and Archbutt1 state that iron exists in aluminum as FeAl3 and silicon as elementary Si. The solubility of FeAl3 in solid aluminum is practically zero, or at, least so small that the smallest trace of this compound is always visible as a separate constituent. Under the microscope an untrained eye can hardly distinguish, without etching, the two constituents FeAl3 and Si, but they can be differentiated by suitable etching reagents. Anderson2 also found the same results. At the same time, Merica, Waltenberg, and Freeman3 found a constituent of unknown composition. They found a small thermal effect, at 610° C., on the cooling curves of aluminum with small amounts of iron and silicon. The intensity of this effect increased with increasing silicon content, until an effect occured at 576° C. due to the eutectic between aluminum and silicon. The authors ascribed the effect at 610° C. to a compound, which they call "X constituent." It was thought to be a ternary compound containing iron and silicon and could be observed under the microscope as dark particles. Dix4 has published unetched photomicrographs of an aluminum with 0.51 per cent. iron, 0.99 per cent. silicon, and 0.32 per cent. copper that shows three constituents: the dark Si (black in the figure), the lighter FeAl3, which appears in half tone and crystallizes in needles, and a constituent of the same color as FeAl3 but of different crystal form, often resembling Chinese script. This last constituent, Dix thought, is a compound of Fe and Si; not the compound FeSi but a compound containing a relatively small amount of silicon. Therefore an alloy of aluminum, iron, and silicon (the copper should not be regarded in the following considerations) must contain the following four constituents: Al, FeAl3,

Jan 1, 1926

By L. S. Panyity

THE State of Ohio is among the pioneers in the production of oil and gas. Numerous anticlinals, such as the Macksburg, Cow Run and Newport, have been thoroughly developed, and the pools found in connection with them are quite in accord with the structural theory. Numerous oil and gas pools found in the Berea sand, however, demand a different explanation. The study of these pools belongs to the sub-surface geologist, as it is possible to understand the factors controlling "off-structure" accumulations only after a careful study of well records. By carefully analyzing the various 'conditions over a large territory, it is possible to understand the otherwise meaningless mass of data that one may have at hand, and put it into tangible shape, from which various conclusions may be drawn. The territory here discussed includes Belmont, Guernsey, Muskingum, Noble, Monroe, Morgan, Washington, Athens and Meigs counties, containing the majority of the prolific oil and gas pools of the Carboniferous system in southeastern Ohio. The general dip of the strata is to the southeast, the entire territory lying on the northwestern flank of the Appalachian geosyncline. The best known oil- and gas-producing horizon in the territory is the Berea sand, which lies near the lower part of the Mississippian, with the Sunburry shales (the coffee-shales of the driller) above, and the Bedford shales below it. The Bedford is underlain by the thick Ohio shales. The Ohio and Bedford contact is considered to be the dividing line between the Carboniferous and Devonian systems. The Berea is one of the most persistent of recognizable oil and gas horizons; its outcrop has always been found in its expected place, and it has always been penetrated whenever the drill went deep enough. It is not expected, however, even of the most uniform formations, that no lithological variations should occur, and the Berea is no exception. Nevertheless, there appears to be a certain regularity in its variation, the main features of which directly affect the accumulation of petroleum.

Jan 8, 1918

By J. M. Bugbee

THE engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance.

Jan 1, 1942

R. MOLDENKE, Watchung, N. J. (written discussion*).-It is some-what difficult to discuss the paper of Mr. Stork, when the description of the cupola melting occurrences indicates that his practice is open to question. The evident burning of much of the steel charged,. coupled with the remarkably low silicon content of the mixture as shown by the resulting product, throws the entire melting practice into that of making cupola malleable. If anything is wanted here, it is a. high bed to melt upon, and yet Mr. Stork in the very beginning of his paper speaks of the evils of oxidation due to a "high" bed, etc. The experienced foundry-mall would judge at the outset that Mr. Stork has kept his bed in the cupola too low, and naturally got a lot of oxidation from the blast. The oxidation of steel when used in large quantities in cupola mixtures is a well-known phenomenon, and is readily understood. One has but to. put a file into the forge fire and watch it burn when heated high enough. The melting point of steel being higher than cast iron, heavy pieces may dig way into the bed before being completely melted away, the last por-tions being directly exposed to free oxygen from the blast. Another situation not to be forgotten is the oxidizing effect of carbon dioxide at high temperatures. A serious oxidation of the steel is quite conceivable if in the zone of maximum carbon dioxide and minimum carbon monoxide-free oxygen being entirely absent. Hence the well understood practice of never melting a mixture with much steel unless the bed is kept exceed-ingly high; or again the above-mentioned malleable practice. Mr. Stork mentions the impossibility of deoxidizing a heat. after the steel contained has been oxidized. This is true to a great extent with the ordinary deoxidizers, such as silicon and manganese, but can be brought about by vanadium, titanium, magnesium, etc. Proper melting, however, makes this unnecessary.

Jan 10, 1919

By D. H. Bacon

Nearly all men are too busy with their own affairs to keep informed of the progress in other lines. From time to time we read statistics showing the development in some industry that astonish us; but the feeling of surprise soon fades: to be followed by others that likewise pass away. A short resume of what has been done in one line may be of interest. Down to late in the fifties the ore-product of Lake Superior mas handled over a mule-tram-road to Marquette; now the Duluth, South Shore and Atlantic, the Chicago and Northwestern, the Wisconsin Central, the Duluth, Superior and Western, the Duluth, Mesabi and Northern, the Duluth and Iron Range and the Lake Superior and Ishpeming railroads serve the shippers. Down to nearly 1870 a 700-ton ship was an enormous craft, the loading of which required two days; the unloading being seldom accomplished in that time. In 1871 the largest ore-barge carried 1050 toils and made twelve trips per season. Now the cargoes reach 5000 tons, the loading requiring less than three hours, and the unloading ten hours. Now the mines cover more land than was familiar to even the " timber-cruiser " when the Jackson mine was opened. The annual shipments have grown from a few thousand to 10,000,000 tons, and the ability of the mines to produce is not taxed. Lake-freights are at one-eighth, and rail-freights at one-quarter, of early prices. The deeper waterways, commodious locks and large ships of to-day are in a greater measure due to the movement of ore than to any other cause. Great savings have been made in each detail of each department. The only item of cost that has not been lessened, I am glad to say, is the money paid to men. Wages, measured by what they will buy, are as high

Jan 1, 1898

By Irwin R. Higgins

CONTENTS A. Introduction B. System Description C. Uranium Pilot Plant Programs D. Summary INTRODUCTION The Chem-Seps Continuous Countercurrent Ion Exchange (CCIX) contactor was first conceived of in 1951 at the Oak Ridge National Laboratory. In the 27 years that have passed, there has been a steady stream of pilot plant process development studies on a variety of processes far too numerous to mention. These have been in the area of water and waste treatment, chemical processing, ore leach treatment, and many others. Many successful production systems have been installed and operated in a variety of applications. A few of these are described herein together with a description of the system and its operational characteristics. SYSTEM DESCRIPTION Chem-Seps Continuous Countercurrent Ion Exchange* is a single loop in which various sections are separated by valves to isolate the sections performing different functions simultaneously. (Refer to Figure 1). To explain the working of a typical unit, let us use a simple configuration used in water softening or demineralization. The resin is moved in small increments by the hydraulic ram action. All solution flows are countercurrent to the flow of resin. The contaminants are removed in the process cycle and the resin is moved in the pulse cycle. A controller in the effluent stream from the treatment section senses the proper limit permissible in the effluent. In the process cycle, the influent enters through a set of distributors, moves downward and leaves through a set of collectors. Simultaneously the regenerant enters through valve RE and leaves through valve WA. The rinse enters through valve RI and its duration is controlled by an interface controller. In the process cycle, valves B, C, and D are closed, isolating all the sections. The duration of the process cycle is 4-10 minutes depending on the contaminants to be removed and is controlled either by a timer if the contaminants are fixed, or a controller in the effluent stream, if the contaminants fluctuate at short intervals. Valve A is open and resin is dropped to the pulse section simultaneously with the removal of contaminants in the treatment section, regeneration of loaded resin in the strip section, and rinsing of regenerated resin in the rinse section. As the resin drops through the valve A, it is backwashed to remove the suspended solids or resin fines. Removal of these fine particles is important to avoid the unnecessary pressure drop in the bed and plugging of the distributors. At the end of process cycle, all flows going into the unit and out of unit are automatically shut off. The valve A closes and valves B, C, and D open in proper sequence. A slug of water enters through valve PU, a predetermined incremental volume of resin moves into the regeneration section, an equal volume of regenerated and rinsed resin enters the bottom of the treatment section, and an equal volume of the loaded resin leaves the top of the treatment section and goes into the resin reservoir section. (The resin movement is plug flow with the Reynold's number being in the laminar region of the curve, and no fluidization occurs during the pulse cycle.) The total time required for proper sequencing of valves and the movement of resin is 20-30 seconds. At the end of this period, the valves B, C, and D close and valve A opens. The solution valves open and normal steady state operation begins. All valves are interlocked and properly sequenced. The resin movement is precisely controlled by sonic devices. Special Features of Chem-Seps CIIX "Downflow"*: The raw feed in the treatment section moves downward and the resin moves upward in the treatment section. The "downflow" of feed overcomes the handicap encountered in "upflow" systems. The "upflow" of feed requires a certain minimum flux during process cycle to lift the bed and keep it

Jan 1, 1979

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By Foster Bain

THOUGHTFUL people have raised questions as to how long nature's bank could continue to accept our drafts. These questions came to the fore so persistently, and there were so many evidences -such as the failure of natural gas in Indiana, the increasing scarcity of lumber in the Lake Superior region, the progressive sterility of Southern farm lands, the choking of the Sacramento River by tailing-point-ing to possible danger from overdraft or to misuse of resources and opportunity, that President Roosevelt called a conference which assembled at the White House on May 13, 1908, to consider these and related questions. This, the first great Conservation Congress, had a wide and beneficial influence on the thought of the world. It profoundly influenced the course of succeed-ing events and, while even yet there are sharp dis-agreements as, to the wisdom of much that has been done in the name of conservation, I believe that thoughtful men, and engineers especially, agree that the time had come when sharp attention was properly called to the waste that accompanied development of our resources. RESOURCES LARGE BUT NOT INEXHAUSTIBLE In 1908 there was a surprisingly large number of men, who should have known better, prepared to argue that our resources are "inexhaustible." No competent mining engineer, of course, believes that, as regards minerals at least. They may be, and, in most cases, fortunately are, large; as to many of them our knowledge is too general to permit measuring the reserves; but we know now, and I think the public appreciates, that there is a limit to our supply of gas, oil, coal, iron, and metals. Indeed, with the inten-sive study made necessary to meet the demands of the war, and the more careful accounting required by the newer systems of taxation, depletion has become a common word, and that mines are wasting assets has become a platitude.

Jan 8, 1922

By A. J. Lanza

IN view of the immense amount of attention that silicosis has received in this country in the past few years, it is timely to review the status of the silicosis problem at present. Who gets silicosis? The individual exposed to the inhalation of free silica dust. The effects upon the individual depend upon the amount of silica inhaled or, in other words, the severity of exposure, rather than upon any special variation or susceptibility among those exposed. A considerable amount of study has been given to determine what may be the role of predisposing causes in the development of silicosis. To mention one instance, at the Picher Clinic careful records were kept of all previous illnesses of the men examined as well as abnormalities present at the time of examination. Examinations of over 27,000 miners were made during the years the clinic was conducted under governmental auspices-a very fair sized sample. The general conclusions from all this work were that the incidence of silicosis is not appreciably influenced by racial, structural, or other inherent qualities; it is influenced by acquired defects-particularly as these affect the lungs. That is to say, the average run of human beings respond similarly to similar exposures to silica dust and those whose lungs are already impaired by tuberculosis or other pulmonary disease acquire silicosis more readily than those with healthy lungs. It may well be, and there is some clinical evidence in support, that negroes acquire silicosis more readily than do whites, but the infection factor has not been so carefully studied among negroes exposed to silica as it has among whites. We know that tubercle infection is more prevalent among negroes than among whites. There may be other factors concerned in the development of silicosis in negroes as compared to whites, but there is not available information upon which to base positive statements. INFECTION AND COMPENSATION Our first ideas about silicosis in this country were derived from early studies in the mining industry where the silica exposure was severe and

Jan 1, 1937

Discussion of the paper of DORSEY HAGER, to be presented at the Colorado meeting, September, 1918, and printed in Bulletin No. 138, June, 191S, pp. 1109 to 1118. WALLACE E. PRATT, Wichita Falls, Tex. (written discussion*).¬Mr. Hager has touched upon interesting problems related to the broad subject with which he has entitled his paper. As to the existence of the important structural feature in the buried Bend series, which Mr. Hager constructs from well-logs, and designates as the "Bend Arch," there seems to be general agreement among a number of observers. Indeed, M. G. Cheney1 and Robt. T. Hill2 have each published structural maps of the Bend Arch that do not differ essentially from the map shown in Mr. Hager's Fig. 1. The reflection, in the overlying, unconformable Cretaceous, of certain folds in the Pennsylvanian, with which the petroleum accumulations has to do, is an important observation on the part of Mr. Hager, since, as he says, much critical territory is covered by Cretaceous, and it is highly desirable that the underlying Pennsylvanian structure be mapped, if possible. If the folds in the Pennsylvanian are of post-Cretaceous age, then it should be possible, in spite of the intervening unconformity, to determine approximately the position of buried folds beneath the Cretaceous overlap. The idea of post-Cretaceous folding would not be out of accord with the suggestion by Carroll H. Wegemann that the folding of the Permian beds in southern Oklahoma was still in progress as late as the Tertiary.3 But most observers have related the folds in the Pennsylvanian and Permian beds at the surface, both in North Texas and southern Oklahoma, to the process of. emergence of the land area at the end of the Permian. It seems more probable that the reflection of Pennsylvanian folds in the unconformable Cretaceous which Mr. Hager observed is due to long continued persistence of stresses which were largely relieved at the close of the Permian, than that the principal period of folding was post-Cre-taceous; this being the case, it seems likely that only folds of greatest intensity in the Pennsylvanian will, be decipherable in the Cretaceous overburden, and that many promising structural features are so concealed by the Cretaceous as to escape detection except by drilling.

Jan 8, 1918

By Alden B. Greninger

Although the crystallography of lattice transformations has been studied extensively during the past few years, these studies have been limited, with few exceptions1'2, to specimens in which the transformed lattice appears as a segregate phase. A realization of the technical importance of the segregation mechanism, especially in the formation of martensitic structures and in age-hardening phenomena, has undoubtedly stimulated research in this direction. In the crystallographic studies of segregation, the general problem has been to relate the orientation of the parent crystal to that of the segregate crystals. The technique has been complicated by the fact that it has been necessary to deal with the presence of as many as 24 ideal segregate orientations within one parent lattice; furthermore, the segregate lattices are invariably scattered (seldom less than ±2º, often as much as 15" or 20') about these ideal positions. It is probable that a more complete picture of phase transformations may result from a study in which complete lattice relationships between individual grains are evaluated, thereby providing an additional parameter which when it is necessary to work with multiple segregate orientations, cannot be evaluated. The present paper presents the results of such a study, ? wherein a peritectic reaction is made use of to produce the transformed lattices. Matebials and Methods Pem'tectic Reaction.—In Fig. 1 is reproduced a portion of the copper-zinc equilibrium diagram, which includes the peritectic reaction a + liq. —ß. A liquid of composition between B and D upon solidifying will

Jan 1, 1937

By Frank R. Hunter

Introduction Scope of Work This paper represents the results of an investigation of the presence, amounts, and degree of concentration of heavy minerals found in the pulp of the phosphate flotation plant at Peace Valley, Fla., which is operated by the International Minerals and chemical Corporation of Chicago. In this paper, heavy minerals are those, excepting collophane, that sink in acetylene tetrabromide with a specific gravity of 2.95. Percentages of heavy minerals at several points of the flowsheet and the species of minerals have been determined. Some information as to the screen size of the minerals has been acquired. Previous Work All previous published reports or investigations of the deposits of heavy minerals in Florida have been limited to present beach sands. The mining operations conducted by the Humphreys Gold Corp. about seven miles east of Jacksonville along an ancient shore line have been described in trade journals, but descriptions of the minerals have been lacking. Commercial grades of ilmenite, zircon, and rutile are produced on a large scale. Papers have been published on heavy minerals found on the Florida beaches.1-6 Location "International's" Peace Valley flotation plant is in south-central Polk County, Fla. about eight miles south of Bartow and along the Atlantic Coast Line Railroad. The mine surrounds the plant and includes about 1500 acres of the phosphatic lands in this area. Geology General Setting All of the rock underlying the area is almost horizontal. The oldest bed exposed is part of the Hawthorn phosphatic limestone of Miocene age. This outcrops in the stream bed of the Peace River about one mile east of the plant. Elsewhere the Hawthorn is covered except where it has been exposed by mining operations. The Bone Valley formation of Pliocene age, which is the phosphatic stratum extensively mined in this area, unconforma-bly overlies the Hawthorn. Resting unconformably upon the Bone Valley formation are Pleistocene (?) terrace deposits of unconsolidated quartz sand which comprise the overburden of the phosphate ore. Stratigraphy Hawthorn formation: "Bedrock" of the pebble phosphate deposits is a cream to white colored, sandy, dense limestone containing varying amounts of small grains and nodules of collophane. The upper surface of the formation is undulating and irregular showing evidence of former

Jan 1, 1949

By I. R. Kramer

A study was made of the effect of surface-active agents an copper, gold, and zinc single crystals as well as polycrystalline aluminum. The study on coppw showed that the maximum effect of the surface -active agent occurred at the same concentration of the solution as that at which the rate of solution of the copper soap was the greatest. Surface -active agents did not affect the creep behavior of gold or freshly polished zinc specimens. The creel-, rate of zinc specimens in a solution containing a surface-active agent zoas always lower than that of freshly polished specimens. In previous papers1'2 it was reported that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing dur- ing tensile deformation, it was found that the slopes of Stages I, 11, and In were decreased and the extent of Stages I and I1 were increased when the rate of metal removal was increased. The results of the investigation of surface-active agents showed that changes in the slopes and extents of Stages I and II occurred when single crystals of aluminum were deformed in tension in a bath containing solutions of paraffin oil and stearic acid. The amount of change was a function of the concentration of stearic acid and the maximum effect occurred at a concentration of 0.002 mole per liter. These results were interpreted2 in terms of the rate of solution of metal soaps which form as a result of the chemical reaction between the surface-active agent and the metal. According to this interpretation, the "weakening" effect is controlled by the rate of solution of the soaps which depends upon the concentration of surface-active agents. At low concentrations, the number of metal soap molecules formed is low; at high concentrations, the rate of solubility is low, because of the high degree of saturation.

Jan 1, 1963

By Donald Barton

THE purpose of this torsion balance survey and the quantitative calculations was to delimit the extension of the cap rock at the Hoskins Mound salt dome. The sulfur ore in the Gulf Coast sulfur-bearing salt domes occurs in the lime rock, which is the outer layer of the cap-rock mass, and also in the underlying gypsum zone. The status of the exploration and exploitation of the Hoskins Mound dome at the date of this survey is shown by Fig. 1. The mound had been covered by the very early prospect wells of the Mound Oil Co., and the later and more numerous prospect wells of The Texas Company. The Freeport Sulphur Co. was producing from the flank wells in the southwest quadrant. The limits of the cap were surmised to lie inside the centers of quad-rangles 4F, 3F, the center of the NE. ¼ of 2E, and the north line of 2D. That surmise was based partly on the data of Fig. 1 and partly on the position of the edge of the topographic mound. The management of the Freeport Sulphur Co. wished to block out the extent of its ore reserves with a minimum of expenditure. The management was informed by the writer that no geophysical method could map the presence or quantity of sulfur directly, or determine the presence and quantity of the lime-rock cap independently of the rest of the cap, but that a reasonable probability existed that the approximate position of the edge, the depth and the thickness of the cap-rock mass as a whole could be determined through quantitative calculations based on the data of a very careful torsion balance survey. Considerable lime rock would probably be present, of course, wherever much cap rock was present. This paper presents the data of the survey, our calculated prediction of the configuration of the cap rock, and the degree of confirmation by the subsequent drilling. The survey was made by the Geophysical Research Corporation, under the direction of the writer. The work of the calculations was done by Andrew Gilmour, then assistant to the writer.

Jan 1, 1936