Search Documents

By Kung-Ping Wang

This is the second installment of two-part article on the Far East. The mineral situation in Hong Kong, Indo-China, Thailand, Burma, Malaya, Indonesia, the Philippines, and British Borneo is covered.

Jan 12, 1951

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-In this exposition of experimental data, the author infers, indirectly at least, that by the Charpy test information was obtained that led to the improve-ment of certain ordnance parts and that this improvement could not have been attained without the Charpy test. On examination of the data, however, it appears that the important point of the whole matter was that while the material had been accepted from the results of longitudinal tensile tests, it was really transverse ductility that was desired. The writer has no desire to attempt to detract from the value of the paper or to discredit the Charpy test in any way, but he would like to ask the author if he will not give more clearly his reasons for preferring the Charpy impact test for investigational and control work of this kind, over the more usual tensile test made in a transverse direction. The tensile test pieces are more cheaply made than the square notched impact bars; and from the former the limit of elasticity and the ultimate strength as well as, the ductility are obtained, while in the Charpy test only one property is measured. It does not seem that the author has shown a sufficient reason for favoring the latter test, when both it and the trans-verse tensile test served his purpose equally well in indicating the proper metal and treatment required for his special forging, and it is hoped that this reason will be given more clearly as a matter of useful general information.

Jan 11, 1919

Jan 1, 1941

By M. E. Shank, J. Wulff

In view of the current interest in magnetic materials having rectangular hysteresis loops, as for example those obtained with the grain oriented 50 nickel 50 iron alloys,t we wish to call attention again to the results obtainable with the perminvar (Co-Ni-Fe) alloys heat treated in a magnetic field. Data taken from direct current measurements made prior to and during World War II give the typical values shown below for two of the perrninvar alloys. Fig 1 and 2 show- the hysteresis loops for these samples. The first sample above consisted of small rings punched from 0.014 in. sheet stock. These rings were heat treated at 1000°C for one hour in a hydrogen atmosphere and then cooled with the furnace to 750°C at which point they were subjected to a magnetic field of 15 oersteds maintained during cooling to room telmperature. The molybdenum perminvar sample consisted of a spirally wound core of 0.001 in. tape. The heat treatment was the same except that box annealing methods were used and no hydrogen atmosphere was employed. Even better properties might be expected using hydrogen. The heat treating temperatures and cooling rates are not critical. Rectangular hysteresis loops produced in other perminvar alloys by heat treatment in a magnetic field were described earlier.',? Properties similar to those described above are realized in perminvars manufactured by conventional methods. Drastic cold working which in practice limits the final thickness and is gen- erally expensive may thus be avoided. This information may be of interest to those concerned with magnetic alloys and the development of contact rectifiers, magnetic amplifiers and so on.

Jan 1, 1950

By Ch. J. Raub

A review will be given on the electrodeposition of Au, Ag and Pd and their technically important alloys focusing on recent work at the Forschungsinstitut. Special emphasis will be given to the influence of impurities on the behaviour of the electrolyte and the properties of the deposits, e.g. on resistance and on thermal and mechanical behaviour. The importance of C in gold and silver deposits and of H2 in Pd and its alloys at normal and high speed deposition rates will be discussed. Among Pd alloys attention will be focused on the Pd-Ni and Pd-Ni-Co systems. Comments will be made on deposition of Rh and Pt.

Jan 1, 1984

By H. B. Emerick

An effort has been made to evaluate the individual influence of various factors in steel making and rolling operations upon the surface quality of semi-finished steel products. The thoughts expressed are not entirely theoretical, but rather are based upon several years critical observation of mill yields and rejec-tions and are supported by actual data wherever this has been possible.

Jan 1, 1940

DURING the month of March there was some lifting of the veil, revealing somewhat of the maelstrom in the economics and politics of the world. Great Britain was in throes of political controversy, with threats of resignation by Lloyd George and a general election to ensue. Ireland was uneasy with internecine squabbles. The leaders of the opposing sides have been summoned to London for a conference which Parlia-ment believes offers the only hope of a solution of the present difficulties. France, awakening more and more to grim realities, learned of a budget for 1922 calling for more than 50 billion francs, or nearly one-third of the estimated national production, with the prospect that after this deduction is made there will be nothing left over what is required for the immediate support of the, people, and that on a reduced scale. Germany, although hard at work, found itself coming closer and closer to financial collapse and repeated its intimations that it would be unable to keep up with the provisional payments of 31 million gold marks to the Reparations Commission every 10 days as arranged at Cannes. Russia suffered more acutely from the famine and there were evidences of political insubordination among the Ukrainians. Egypt was in trouble arising from determination to win independence. About the middle of March the complete independence of Egypt was established and that country passed into somewhat the same relation-ship toward Great Britain that Panama has to the United States. At the head of the Adriatic, Fiume came into notice again with disorders threatening to produce conflict between Italy and Jugoslavia. In the Near East there were forebodings of trouble through resumption this spring. of the war between Greece and Turkey.

Jan 4, 1922

By Chas. A. Ashburner

THE Bradford Oil District lies in the northern part of McKean County, Pa., and the southern part of Cattaraugus County, N. Y. Although petroleum was first found in the producing sand in 1871, it was not until the early part of the year 1875 that a productive horizon was acknowledged to exist, even by those most largely interested in the production of the crude oil. It has been reported to me that the first well drilled in the valley of the Tuneangewant Creek (commonly called Tuna Creek) was drilled by F. E. Dean and brothers in 1865. This well was located on the Shepherd farm, near the present site of Custer City. One hundred and sixty feet of drive pipe was used, and the hole was drilled to the depth of 900 feet. The producing sand at Custer City is found about 1130 feet below the level of the railroad track. The Shepherd farm well was therefore abandoned over 200 feet above the top of the oil sand. The next well was drilled by the Dean brothers on the Clark farm at Tarport. Drilling was stopped at a depth of 605 feet, or over 400 feet above the top of the oil sand. In the year 1862 the old Bradford well, since known as the Barnsdall well, was drilled to a depth of 200 feet with a spring pole, and then abandoned. In the spring of 1866 the citizens of the village of Bradford concluded to club together and sink the Barnsdall well deeper. It was drilled to a total depth of 875 feet, or to within 150 feet of the Bradford producing sand. All of these wells were drilled with the expectation of finding the Venango County oil, and at

Jan 1, 1879

By B. K. Asdell

Crude kaolin exhibits a wide particle size range in which kaolinite is the predominant mineral. Bene-ficiation by wet processing produces high-brightness white pigments. The wet processing techniques peculiar to kaolin beneficiation are emphasized in this article in some detail. Included are discussions of long-distance pipeline transportation, centrifuga-tion, flotation, spray drying and shipment as 70% solids slurry. Georgia, a state seldom considered to be an important mineral producer, has one surprising feature — it is the nation's largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite. The sedimentary Cretaceous deposits of the Coastal Plain are the source of most of the kaolin produced in the Southeast. These deposits are of relatively high purity, and it is not uncommon to find the clays running greater than 90% kaolinite. Beneficiating plants using wet processing techniques are most numerous in an area within about 50 miles east of Macon, Ga., in a band approximately 15 miles wide. Kaolin may vary widely in quality from one deposit to another, or within the same deposit. The qualities critically examined are brightness index as measured by reflectance, viscosity of water suspensions, bleachability and particle size distribution. Crude kaolin always contains sand and mica in varying amounts, along with small amounts of many other minerals. These are classed collectively as "grit" because; they are generally coarser than 325

Jan 1, 1968

By N. J. Themelis

What is the "best" copper smelting technology? When a future Agricola examines the development of copper smelting in the 20th century, he will be amazed at how little took place in the first half of the century and how much in the second. In a period when the technology of transportation, communications and chemical processing advanced many fold, copper smelting remained practically static. The result of tightening energy supplies and stringent environmental controls in recent years has been a spate of development activity that not only is challenging the supremacy of the reverberatory furnace, but threatens to wipe out pyrometallurgical techniques entirely.

Jan 1, 1976

By M. T. Abasov

Among a host of challenges dictated by the explosively developing scientific and technical revolution, the improvement of control and management is one of the most essential problems. This problem is also of far-reaching importance for the oil and gas industries. An oil and gas extracting complex is an involved multilink system characterized by a great number of elements and by intricate interconnections between these elements. Of paramount importance for these systems is the quality of control. Any deviation of the control from the optimum reduces the effectiveness of the system and deteriorates its basic technical and economic factors. In case of large systems, even a relatively small deviation from the optimum may result in considerable material and power losses. Optimization of control of large production systems is therefore one of the basic means to enhance their effectiveness. The present paper discusses a development control problem for a multilayer gas deposit using the method of simultaneous exploitation of several strata by means of a single well. The optimum control is achieved by determining the dynamics of changes in the number of producing wells in a reservoir with regard to the depth of occurrence of these reservoirs as well as the difference in the time of introduction of the wells from drilling and their transfer to another reservoir. A mathematical model was constructed for the problem under consideration and a method was given to solve this problem. The problem was dealt with under the assumption that either each of the reservoirs or a part of them have vertically overlying areas and that there is no hydrodynamic interference between the horizons. It was

Jan 1, 1977

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

By M. P. Boss

Of the two methods of mechanical reduction—that of percussion and that of abrasion—it is not easy to say which was first employed by primeval man. The stone hammer and the flat or hollowed stone used for grinding are found together in the remains of prehistoric periods. But the use of the maray, or bucking-stone, developed from the hammer, was probably introduced later than that of crude millstones. Diodorus Siculus, the Roman historian of the first century B. c., mentions such millstones as used in the mines of Egypt to pulverize material which had been previously broken in a mortar. The invention of the arrastra for fine grinding is declared by some authorities to have been made by Bartolomeo de Medina, at Pachuca, Mexico, about A. D. 1557—which is quite probable. Being the first to amalgamate silver on anything like a business scale, he must have felt the necessity for oregrinding apparatus of greater capacity than the old primitive millstones; and the arrastra was thus the natural successor of the millstone. It is very unfortunate that the archives of Pachuca, which has made so much history in ore-treatment, were destroyed in some one of the many insurrections for which, also, the place is renowned. The first application of the stamp to the crushing of rock is asserted by some writers to have been the invention of a Saxon nobleman named Von Maltitz, about the year 1505. Better authenticated reference, however, is made to one Paul Gronstetter, a native of Schwarz, and called an ingenious worker, who, in the year 1519, established at Joachimsthal a process of wet stamping and sifting. Two years later, a larger plant was established at the came place. It is said that he had previously introduced the same device at Schneeberg. How much of the invention was due to Gronstetter is not certain;

Jan 1, 1902

By R. E., Head

THE use of lime in flotation has become so general in recent years that its functions are familiar to plant operators. The conditions and phenomena described in this paper are of interest because they are directly associated with the use of lime as a reagent and the resulting formation of lime scale worth nearly $1 per pound for its gold content. It is not known to what extent lime scale is common in flotation plants where lime is used, but as several occurrences have been re- ported, its existence is not limited to one particular plant. In November, 1927, the author's attention was drawn to a lime scale that formed on the sides of Callow flotation cells in the Walker Mining Co. mill at Spring Gar- den, Cal. The scale was described as an accumulation of hard material that built up on the sides of both the rougher and cleaner cells and in some instances attained a thickness of 2 in. The lime scale builds up in the cleaner cell at the rate of about 1/10 in. per month, or slightly more than ?12 in. during six months' operation. The rate of growth in the rougher cells is slower, and about 3/s in. of scale forms in six months. Analyses' of typical lime scale samples are as follows:

Jan 1, 1928

By Samuel Frantz

THE purpose of this paper is to relate briefly the development of magnetic separation and its extension from the separation of iron into its present use in the nonmetallic field, to suggest possible future exten-sions of its field of usefulness and its possible cooperation with other separating methods. The engineering design of separating machines, and statistics as to the number of machines in operation, types, their location and production are outside the scope of this paper. Specific data will be given, however, on certain selected applications. A large part of human endeavor consists in separating one thing from another; the good from the bad, the desired from the undesired. In fact, a philosopher might plausibly claim that separating things into categories and choosing between them is the object of thought itself. In dealing with matter, separation is nowhere more inherently necessary to attain our objects than in mining and metallurgy. Both our desire and our ability to make separations are results of the physical differences between things. Gross separations such as removing ore from worthless rock or coal from slate are usually made visually and depend upon form and color, which are physical properties. When the desired and the undesired things are intimately mixed, however, it becomes impractical to select visually even if the individual particles are readily recognizable to the eye, and some automatic way of making the particles separate themselves on the basis of their own inherent differences in physical properties must be resorted to. Some of the physical properties which have been used as a basis of separation are: color, shape, hardness, size, density, elasticity, surface properties (surface tension in contact with liquids, etc.), electrical conductivity, dielectric constant, and magnetic susceptibility. Differences in these properties are used in the following methods of separation: color sorting, sifting, settlement in air and in liquids, floatsink methods, flotation, electrostatic and magnetic separation.

Jan 1, 1932

By V. F. Hollister, M. Bernstein

The Copaquire porphyry copper deposit lies in an island of pre-Upper Tertiary rocks surrounded by Quaternary and Upper Tertiary formations. The pre-Upper Tertiary appears to be a horst block in a typical basin-range setting. Major right lateral faults have been mapped within the range from Chuquicamata north to Copaquire. All of the major porphyry copper deposits known in the block (e.g., Quebrada Blanca, El Abra, Chuquicamata, and Copaquire) are on or are very close to one of these major right lateral shears. In the Copaquire district, an epizonal igneous complex with diorite, quartz diorite, quartz monzonite, and intrusive dacite (in that intrusive order) invade folded Jurassic shale. Mineralization appears spatially and temporally associated with the quartz monzonite porphyry and dacite. Alteration zoning shows two separate core phyllic (quartz-sericite-pyrite) zones within one large argillic (clay-pyrite) zone. A propylitic (chlorite) zone is peripheral to the argillic zone. No potassic zone has been recognized yet at the surface. The intrusive petrology together with the phyllic, argilic, and propylitic alteration zoning as well as the chalcopyrite-molybdenite ore mineralogy characterize this deposit as being typical of the Lowell and Guilbert model. Copper and molybdenum minerals appear to be most strongly developed in the phyllic zone, in either a breccia or a zone of veinlets and stockwork which trend dominantly northeast, conjugate to the district's largest fault, the Sulfato fault. The setting is basically similar to that found in some other porphyry copper deposits in this block, in that the ore body is a zone of veinlets which appear to be genetically related to movement on a major north-south trending right lateral fault. The presence of the major fault in each deposit, and the speculative hypothesis that paleo-subduction zone operated at the time of mineralization, suggest the possibility that mineralization took place when a major fault permitted escape to the surface of cal-calkalic magma generated in a subduction zone as proposed by Ericksen. A hypothesis such as that proposed by Ericksen explains the near linearity of porphyry copper deposits in Chile, since the source of calc-alkalic magma would exist at about the same distance from a paleo-trench throughout the length of the paleo-subduction zone.

Jan 1, 1976

By J. C. Uy, A. A. Burr

A quantitative relationship between the allotropic phase boundaries of zirconium-base binary systenzs and the solute metallic valence is shown through an intermediate thermodynamic parameter. A simplified equation relating this parameter to the phase boundaries is briefly reviewed, and data from the literature are used to show the relationship of this parameter to the solute metallic valence. It has been reported that the solute metallic valence can be used as an index of phase stabilization in zirconium-base binary alloys.' It was shown that the algebraic sign of the slopes of the hcp/bcc phase boundaries of zirconium alloys correspond to the algebraic sign of the metallic valence of zirconium minus the metallic valence of the solute, or, in other words, a solute whose metallic valence is higher than that of the solvent tends to stabilize the high-temperature phase while one whose metallic valence is lower than that of the solvent tends to stabilize the low-temperature phase. Further analysis of the zirconium binary systems has revealed a quantitative relationship between the solute metallic valence and the relative slopes of the two-phase allotropic boundaries. This relationship involves a thermodynamic quantity whose significance can be seen in the following section. PHASE-STABILIZATION PARAMETER Let Qb be the difference between the partial molar heats of mixing of a given solute in the two allotropic phases of the solvent which are in equilibrium with each other at a given temperature, thus A relationship between this term Qb and allotropic phase boundaries has been employed by several au-thors'-= in the evaluation of phase diagrams, and can be briefly derived as follows. Referring to Fig. 1, consider the general case of two allotropic phases, each having a small mole fraction (Xa,Xb) of the solute, in equilibrium at temperature T and atmospheric pressure as represented by the reaction. solute in ß phase =solute in a phase If now a reaction occurs such that an infinitesimal amount of the solute is removed from the ß phase and added to the a phase, there would be a partial molar

Jan 1, 1967

By S. Y. Ezz

The quality and extent of fluidization of fine iron ore beds with gases were investigated. Factors affecting the rate of reduction with H, and the sintering of the partially reduced material were studied. Trials to retard sintering by covering the particles' surface with nonsintering materials were successful. THE gaseous reduction of iron ores is a gas-solid reaction. Hence the fluidization technique seems ideally suited to it. However, a serious drawback

Jan 1, 1961

By William G. Fricke

MaCROSEGREGATION, as distinct from microseg-regation, is often inverse in nature. That is, the eu-tectic solute elements, which are expected to be con-

Jan 1, 1970

By D. L. Wood

INTERNAL oxidation' is a process in which oxy-gen, diffused into a suitable alloy, causes precipitation of solute oxide particles as the oxidation front moves inward. During an investigation of internal oxidation now in progress it was observed that the grain size is relatively small in thin strip specimens that have been internally oxidized in the as-rolled condition. This may be due to the restraint of grain growth by the precipitated oxide particles. It was observed also that the grain size in unoxi-dized portions of partially oxidized specimens was

Jan 1, 1958