Search Documents

By Stephen C. Blair

Laboratory permeability measurements at elevated pressure and at temperatures ranging from 20º to 150°C have been conducted on samples of Ironton-Galesville sandstone. The purpose of this testing was to identify and characterize important physicochemical processes occurring in association with the injection and withdrawal of heated ground water at the U.S. Department of Energy's Aquifer Thermal Energy Storage (ATES) field site in St. Paul, Minnesota. Results indicate that permeability decreased significantly as temperature was increased and that dissolution of the dolomite and silicate cementing agents and accompanying changes in mechanical properties may occur in the heat storage aquifer at St. Paul. Further, loss of permeability with temperature in laboratory samples may be caused by the change in the mechanical structure of the sample. Tests at ambient temperature to evaluate the effect of particle migration under conditions of reversed flow indicate that this process will not significantly impair formation permeability at the St. Paul site.

Jan 1, 1984

By R. Hogg, F. F. Aplan, P. B. Bradley

The mineralogy of the solids contained in the black-water effluent from coal preparation plants has been investigated. Samples were obtained from 13 locations, representing major coal seam in the Appalachian, mid-continent, and western regions of the United States. On the average, the samples were found to contain 60% carbonaceous material with the balance as mineral matter. The mineral fractions from all of the samples from the eastern half of the United States were found to be remarkably similar, consisting of over 50% illitic clays; about 10-15% each of kaolinite, calcite, and quartz; and lesser amounts of chlorite and pyrite. The western samples were somewhat different, generally containing significant quantities of montmorillonite clay. Flotation may be wed to recover additional clean coal contained in the black-water discharge.

Jan 1, 1981

By J. K. Gerlach, E. D. Gock, S. K. Ghosh

Previous experience in leaching chalcopyrite with dilute sulfuric acid has generally resulted in rather poor extraction. However, the reaction rate of the leaching process can be significantly improved by an increase of the crystal lattice defects of the chalcopyrite. It was found that subjecting chalcopyrite to a milling action involving a strong impact, permits 99 percent of the copper to be extracted in a subsequent single leaching stage with at least stoichiometric quantities of sulfuric acid in the presence of oxygen at 100°C. Simultaneously, about 80 to 85 percent of the sulfide sulfur content is converted to elemental sulfur. The dependence of the reaction rate of chalcopyrite on the pretreatment, temperature, oxygen pressure and acid content will be discussed.

Jan 1, 1973

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By John H. Jett

MATERIAL and supply handling is a major problem at underground mines, especially to those operating through deep shafts with small compartments. Mechanization is necessary, yet in many cases cannot be utilized to fullest advantage owing to the limitations of existing plant design. In cases of this sort, improvisation is indicated and adds to the headaches and enjoyment which most mine operators get out of their work. Underground operations at the Copper Queen Branch are principally carried on through three vertical shafts: the Junction shaft, Campbell shaft and Cole shaft. Hoisting depths range from 1400 ft at the Cole through 2700 ft at the Junction to 2966 ft at the Campbell shaft. Men and supplies are moved through each of the shafts. Cage compartments are small requiring all material over 5 ft in length to be handled in an upright position on the cages.

Jan 3, 1953

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By Ralph E. Grim

THE technology of clay minerals is defined, for the purpose of this review, as- the application of fundamental data regarding clay minerals, and techniques of handling them, to the various industries, arts, and professions concerned with clay materials. The aim of the paper is to narrate recent developments in clay mineral technology. This review does not claim to be complete, and perhaps gives undue emphasis to matters that have been worked on in the author's laboratory or with which he has some other connection. In the United States in recent years, particularly since the end of World War 11, interest in clay mineralogy has increased greatly. Many laboratories in many different fields have embarked on studies of clay minerals but unfortunately much of this work has not been published. CERAMICS In the field of ceramics, in recent years, a great deal of interest has developed in clay mineralogy. Papers too numerous to be reviewed here have been published portraying the clay mineral composition of substantially all the important types of ceramic clays in all countries. There has been a growing tendency to attempt to solve processing problems on the basis of clay mineral data rather than chemical analytical data. Likewise, there is an in- creasing tendency to control the characteristics of raw materials on the basis of clay mineral composition rather than chemical composition. In the United States in the last few years something like 50 differential thermal analyzers have been set up, and many are for the sole purpose of controlling raw material and processing. The ceramic industry is currently increasing its attention to the influence of exchangeable ions and soluble salts on physical properties. Ion concentration in clay suspensions has long been a matter of interest, but now it is also of interest in clays in the plastic state because of its recognized importance in the plastic, shrinkage, and bonding properties of clays. Students of clay have long recognized that an understanding of the plastic properties of clays is based on an understanding of the character of the water in clay-water systems, the nature of the binding force between individual clay mineral particles, and the factors that control the character of the water and the nature of the bonding force. In the last few years, some extremely important contributions have greatly increased the understanding of the nature of water adsorbed on the clay mineral surfaces. In this connection the work

Jan 1, 1952

By Wilhelm Rohn

IN discussing the influence of a content of gases on metals and alloys we should probably first consider the physical and chemical conditions under which these gases may be present. By a chemical analysis, such as the total extraction of gases from the liquid metal by melting in a graphite crucible in vacuo, we find only the sum of gaseous chemical elements contained in the metal in any form and no reference is made to the special form under which they have been present previously. CONDITION OF GASES IN METALS In considering gases . in metals we may first turn our attention to gases simply dissolved. Because the solubility of almost any gas decreases suddenly at the freezing point, most of them are released during solidification, developing rise of ingots and blowholes. If only a little gas is dissolved in the molten metal the size of such blowholes may be miscroscopical, or even submicroscopical, resulting in a certain reduction of the notched-bar impact test values. Hydrogen is believed to become less soluble as the temperature is lowered and therefore increasing quantities of this gas may be evolved during cooling between the freezing point and room temperature, leading to unsoundness of the ingot at weak spots; i.e., at the grain boundaries. This gas at the grain boundaries probably is present at high pressure and therefore impairs the mechanical properties to a degree similar to that found in the hydrogen embrittlement of copper. Usually we may trace such gases by observing rising ingots, or at least by the formation of a characteristic pattern of small grooves upon etching.

Jan 1, 1932

By Donald L. Everhart

Beginning in 1906, data has been compiled on the distribution of uranium in phosphate de- posits. Particular emphasis has been placed on uranium in phosphate by a number of geologists and geochemists in the US Geological Survey in research sponsored by the US Atomic Energy Commission (now Nuclear Regulatory Commission) and the US Department of Energy (DOE) during the 30-year period from 1951 to 1981. A comprehensive study of uraniferous phosphate resources the United States and the Free World was completed, under the auspices of DOE, in 1979. Apatite is the main carrier of uranium in phosphate. Uranium generally replaces calcium in the mineral lattice. In marine phosphorite throughout the world, the uranium content is characteristically in the range of 0.005 to 0.02% by weight. Phosphorite takes in uranium by structural substitution in apatite or other mineral phases, by absorption, or by the formation of independent mineral phases. Apatite derived from the interaction of ground water, guano and limestone is typically relatively low in uranium content-in the 0.001 to 0.005% range. In primary accessory apatite of igneous rocks, as well as magmatic and metasomatic apatite segregations of alkalic rocks and carbonatite, uranium content is generally between 0.001 and 0.01%. In all these phosphate deposit types, secondary enrichment of uranium through

Jan 1, 1983

The opening session of the A. I. M. E. was held at the King Edward Hotel, Toronto, on Tuesday, July 25th. Dr. W. G. Miller, on behalf of the Local Committee, opened the proceedings. [ ] President John Hays Hammond, who occupied the chair, introduced Alderman Graham, Chairman of the Reception Committee, and representative of the city, in the absence of His Worship the Mayor. A brief address of welcome was delivered by the Alderman and responded to by President Hammond. The President then requested Dr. James Douglas to present to the honoured Secretary of the Institute, Dr. Rossiter W. Raymond, an oil portrait.

Jan 1, 1907

By E. E. Brownson

THIS paper will be confined to the treatment of methods as applied in the laboratory of the Boston and Montana Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont. As the electrolytic plant of this company operates at a current density of approximately 35 to 40 amperes per square foot when running up to capacity, the arsenic and antimony content of the anodes delivered to the, plant is of considerable importance as bearing on the purity of the refined cathodes turned out. Owing to the rather high relative percentage of antimony, it has always been the custom to determine antimony as well as arsenic in all forms of copper. Thus, anodes have been analyzed in which the antimony was about equal to the arsenic although the average shows about 2 parts of arsenic to 1 of antimony. In the refined copper the relative proportions of the two impurities vary considerably, but probably in the average are about equal. In this latter case, the percentage of the two is so small that ordinarily no attempt is made to separate them, the report of analysis showing percentage of As and Sb combined. Although rapid and exceedingly accurate determinations of arsenic may be made by means of various distillation schemes, the determination of antimony, either by itself or together with arsenic, has always been more or less cumbersome and has required a considerable amount of time. By the methods, details of which follow, the determination of arsenic and antimony, either separated as in the case of anodes or together in case of refined copper, is accomplished in 24 hr. from the time the sample is received by the chemist.

Jan 8, 1913

A PAPER on "Iron and Steel Scrap in Blast-fur-nace Burdens," by W. C. McKee, general super-intendent, Federal Furnace plant, By-Products Coke Corp., Chicago, was published in the October issue of MINING AND METALLURGY, and written discussion by Richard Moldenke was published in the December issue. Following is the stenographic report of the oral discus-sion that took place when this paper was presented at Pittsburgh. J. N. REESE, Monessen, Pa.-I came to the conclusion that Mr. McKee must be using a poor grade of scrap, therefore his loss was high. Mr. Franchot said that there was ex-cess heat in the stack. There is no excess heat in the hearth, therefore, any heat that is used to melt this scrap must come from the stack. By using scrap in a blast furnace you can utilize this excess heat in the stack. The amount of scrap that can be used in any particular furnace involves a direct relation to the efficiency of that furnace. If a furnace is running on a very low-coke rate, you will not be able to use much; if on a high-coke rate, you can use considerable scrap, probably several times as much as that mentioned in these papers-without using any additional coke. This excess heat can be utilized with-out practically any serious mechanical and operating diffi-culties such as might be occasioned by removing gas from a point other than the top of the furnace. I do not think, scrap has any effect on the iron, although I think some foundrymen are trying to prove that it has, and perhaps some open-hearth men may have that idea.

Jan 1, 1927

By T. C. Mendenhall

All persons, actively engaged in your profession, must have a natural interest in the subject of weights and measures. All members of the engineering profession have to do with operations of weighing and measuring—some with measuring more than weighing, and some with weighing more than measuring—but all with both of these processes to a greater or less degree. Methods of weighing and measuring have improved constantly from the earliest times and have kept pace with the advance of other technical processes. It is, therefore, believed that you will be interested in a few remarks concerning some of the more recent advances in relation to the establishment of decimal standards of length and mass in this country. Before speaking of this, I will refer very briefly to some facts which may not be very generally known regarding our customary system of weights and measures. Although the yard is universally accepted as the unit of length, and the pound as the unit of mass, it is not generally understood, I believe, just in what respect the yard is the unit of length, or the pound the unit of mass. That is to say, it is not generally known in what degree these units have been legalized by Acts of congress. Doubtless, many of you are familiar with the facts which I will briefly recapitulate. The Constitution of the United States authorizes Congress to establish a system of weights, measures and coinage. The establishment of a system of coinage, as you know, was one of the first acts of the government, and the system then adopted is certainly one of the most perfect, if not the most perfect, that the world has yet seen. But, although Congress had the power to establish a system of weights and measures, it has never yet seen fit to exercise this power; that is to say, Congress has never yet

Jan 1, 1890

By F. V. Lenel, G. S. Ansell, M. J. Salkind

An experiment is described in which the growth of interparticle necks in an array of loose spherical silver powder at temperatures near 300°C was determined by measuring changes in the electrical resistance of the array. The activation energy for neck growth of contacts was derived by abruptly changing temperature and noting the change in the rate of neck growth. Since the experiments were run under an external load, the changes in activation energy with stress could he determined. The activation energy was found to decrease rapidly with increasing stress. It is concluded that the material transport in the experiments is one of plastic flow by dislocation motion. The variation of activation energy with stress is typical for cross slip of dislocations, an important material transport mechanism in the temperature range investigated. THE process in which powder compacts or aggregates of loose powder are held at an elevated temperature under an external load is called hot pressing or sintering under pressure by powder metallurgists. In this investigation the early stages of this process as applied to loose spherical silver- powder aggregates were studied. The powder particles were approximately 100µ in diameter and the temperature was near 300°C, i.e., below one half of the melting point of silver in degrees Kelvin, where volume diffusion is not expected to contribute to sintering. In the process, the contact or neck areas between powder particles grow. Since this involves plastic deformation of the particles under a constant external load (even though not under constant stress) it would be termed creep by mechanical metallurgists. On the other hand, the growth in neck area observed in compacts or loose-powder aggregates held at elevated temperature without the application of an external load is termed sintering by powder metallurgists. During sintering the major driving force is the stress due to surface tension. However, even when no load is placed on the compact or powder aggregate, an external stress, i.e., gravity, plays an important role in sintering in addition to those stresses arising from surface tension, as was shown in two previous investigations.'" It is therefore postulated that no sharp dividing line can be drawn between the phenomena of "creep" and "sintering". Different material transport mechanisms may be involved in either of these phenomena, but they will depend upon the temperature and the level of stress, but not necessarily upon the nature of the driving force: surface tension or external load. At the low temperatures of this investigation, an external stress much higher than the stress due to surface tension is necessary to obtain measurable rates of neck growth. In order to avoid misunderstanding this phenomenon will be called "creep". The rate of growth in contact area in the loose silver-powder aggregates was determined by meas-

Jan 1, 1965

By H. R. Banks

Pondering the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote "Tho' the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. Principle of Ball Mill The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely he mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? Methods of Grinding The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of he grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1947

By H. R. Banks

Pondering the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote "Tho' the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. Principle of Ball Mill The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely he mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? Methods of Grinding The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of he grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1947

By T. D. Teimann, R. L. Stone

The rate of extraction of silica from certain Wisconsin and Minnesota taconites was investigated by autoclave digestion in sodium hydroxide solutions over the temperature range from 296° to 416°F. Rates obtained were from 7 to 254 g mol per cm2 per sec giving activation energies from 15,000 to 19.000 cal per mol. Activation energy was found to increase with increase of sodium hydroxide concentration. Digestion of different forms of quartz indicated the rate of extraction to be solely a function of surface area under similar conditions of digestion. The results of an experimental investigation on the caustic extraction of silica from certain Wisconsin and Minnesota taconites were presented in a recent publication.' It was shown that residual concentrates containing as much as 65% iron can be produced by this method. The occurrence of silica as a micro-crystalline variety of quartz with high specific surface area gave correspondingly high mean rates of extraction in solutions of sodium hydroxide. The present paper extends this previous work by presenting the results of a study of the specific rates of extraction of silica from these ores as related to temperature, sodium hydroxide concentration and variety of quartz. Calculated activation energies for the dissolution of silica are presented and some possible mechanisms are discussed. TACONITES The low-grade siliceous iron ores investigated included taconite from the Wisconsin Gogebic range and a semi-taconite2 from the Minnesota Mesabi range. These are adequately described in the former paper1 and by the U. S. Bureau of Mines. The principal iron minerals are hematite (Fe2O3) and goethite (Fe2O3 . H2O), while the gangue is essentially a microcrystalline variety of quartz. Minor amounts of other minerals are present. Typical analyses show the Wisconsin taconite to contain approximately 28% Fe and 54% SiO2 and the Minnesota semi-taconite 39% Fe and 39% SiO2. Analyses of the actual samples used are given in Table I. The taconite samples were prepared for digestion by reducing the original ore to minus 200 mesh in a Braun pulverizer. QUARTZ Three varieties of quartz were studied in the investigation: Ottawa sand, chert and chalcedony. The Ottawa sand was obtained from the Ottawa Silica Co. The chert and chalcedony came from Wards Natural Science Establishment. A minus 200 plus 400 mesh fraction of the Ottawa sand, used as a surface area standard, was repeatedly washed in hot concentrated hydrochloric acid followed by distilled water before autoclaving. The other two varieties were used directly after grinding through 200 mesh in a laboratory hammer mill. Analyses of these samples appear in Table 11. Microscopic examination of the silica samples by the oil immersion method showed that the Ottawa sand consisted of clean, uniform spheres of quartz with little deviation in size from a mean diameter of 82µ determined by a distribution count. The other two varieties consisted almost entirely of microcrystalline aggregates of quartz crystals; the aggregates ranged from 10 to 70µ. The individual crystals in the chert aggregates were estimated to be of the order of

Jan 1, 1964

By Elliott J. Roberts

In spite of the fact that the percentage of true colloids in an ore grind is very small,' these pulps exhibit many of the properties of true colloidal suspensions. A quartz particle, appreciably finer than 10 microns in diameter, has a settling rate so low that at a dilution of 5:l or over, the capacity of a settling tank to settle such particles would be uneconomical if the individual particle rate prevailed. However, by grouping the finer particles into aggregates or flocs, the settling rate can be increased to an economical value. The colloidal chemistry of pulp thickening is thus chiefly concerned with particles having diameters of between 1 and 10 microns, although particles as coarse as 40 microns in diameter are more or less involved. These particles must be associated in such a manner that they settle at an economical rate and give a clear, supernatant liquid or overflow. The treatment of the subject may be divided into three phases, cach phase having a more or less different colloidal aspect. The first phase is the problem of getting the pulp or suspension into the proper condition of flocculence; the second is the behavior of the flocculent pulp in its initial and intermediate stages of settling; the third is the behavior of the flocs in the find period of settling or thickening stage. Let us look first into the methods and mechanism of obtaining the flocs and then consider their behavior and properties. Flocculation Colloids are merely ordinary substances reduced to a very small particle size, the upper limit being placed by definition at 1 micron (0.001 mm.) diameter by the soil chemists and at from 0.2 to 0.1 micron by various other colloid chemists. The lower limit is reached only when the particles approach molecular dimensions. The term L'colloid" should not necessarily imply lack of crystallinity. Particles as small as 0.01 to 0.02 micron give perfect X-ray patterns, while with 0.005 micron particles the bands on the powder photograph are merely broaderled and diffused.2

Jan 1, 1935

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943