Search Documents

By K. B. Nowels

The attainment of efficient flooding to a large extent depends upon a knowledge of fluid movement through porous media and the pressures used in controlling this movement. Little has been understood con-cerning the fundamental principles involved in the forced drive of water-flooding and an attempt will be made to present some data which may be of interest. Considerable data and technical information pertaining to natural and artificial water-flooding have been presented in the past by Torrey, Umpleby, Fettke, Panyity and others. Their papers have thoroughly covered the description of past and present-day methods of oil recovery by flooding in the Bradford field, especially an article by Torreyl in the Petroleum Engineering Handbook. A bibliography of papers devoted to watcr-flooding, published in Mr. Torrey's article, is appended to this paper. No attempt has been made, therefore, to describe the installations and procedure necessary in flooding, thus permitting the writer to deal exclusively with the mechanics of water movement in flooding operations and its relationship to well spacing. Artificial water-flooding will probably always be the most successful in oil fields described by Herold as being under "capillary control"" and will probably be useless in fields naturally under hydraulic or volumetric control. The natural water drive in an oil field under either of these two controls may give efficient recoveries, as a result of the regulated encroachment of edge water. Such a "natural flood" resulting from the influence of edge water must not be confused with the term as used in this paper, however. Any reference to "natural flood" will here refer to the old method of flooding formerly used in the Bradford field. This was discovered largely by accident and utilized the hydrostatic pressure created by a column of water standing in a watered-out oil well in forcing the oil to an adjacent producing well. The same principles are involved in either natural or artificial flooding, and the latter method simply

Jan 1, 1933

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

Jan 1, 1938

Jan 1, 1938

Jan 1, 1946

Jan 1, 1938

By B. Paul

1. INTRODUCTION It is known that the elastic modulus of a metal may be considerably increased by dispersing

Jan 1, 1961

Jan 1, 1946

Jan 1, 1935

Jan 1, 1937

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 8, 1950

By A. L. Holley

The intention of this paper is not to discuss this important subject in all its bearings, but merely to point out why mechanical tests of steel, as ordinarily made, are not, alone, of any special value to engineers—certainly not to general mechanical engineers. The agents of the Barrow Hematite Steel Company, one of the largest and most successful Bessemer establishments in England, have recently distributed a report, made by Sir William Fairbairn,

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be done by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts.

Jan 1, 1944

By W. L. Zeigler

The Galena mill of the Callahan Zinc-Lead Co. is of 150 tons daily capacity and is situated at Lake Gulch, 2 miles west of Wallace, Idaho. (Fig. 1. It was constructed during the summer of 1926, work having been started late in June and the plant placed in operation Oct. 15, following.

Jan 1, 1928

By K. Osseo-Asare

The thermodynamics of solid-aqueous solution equilibria up to 200°C In the systems Me-NH3 H2 0 (Me=Cu, Ni, Co) are summarized with predominance area diagrams generated with the DIAGRAM computer program. The implications of the diagrams to ammonia hydrometallurgy are discussed.

Jan 1, 1981

By Joseph Bernhardt

Use of concrete underground at No. 4 mine, Cornwall, Pa., has become increasingly important. Starting with small amounts at finger openings, occasional raises, piers, its use has expanded to entire slushing drifts and haulages. Besides eliminating costly timber repairs, concreting costs of slushing drifts have proved cheaper than timbering. Higher haulage-concreting costs are offset by no maintenance charges during the life of the haulage.

Jan 3, 1950

By D. F. Toner

THE decomposition of the ß phase in the copper-aluminum system has recently been subjected to considerable investigation1-4 As a result of this work, principally by Haynes, much additional interest has been aroused concerning the various transitional or metastable phases in the Cu-A1 system. No attempt has been made to resolve the question of whether the PI and ß" phases of Klier and Grymko5 are the same as the rosette-shaped phase first observed by Smith and Lindlief6 in 1933 during an isothermal transformation study of an eutectoid alloy. It is the purpose of this study, however, to obtain

Jan 1, 1960

By Kenneth A. Grace

Jan 1, 1985

By Edna A. Dancy

Jan 1, 1965

By David Phillips, George Jura

WHEN Bridgman1 determined the volume-pressure relationships of bismuth to 100 kg Cm-2, he found two small volume discontinuities at 45 and 64 kg em-2. Probably every investigator in high pressures has determined the electrical resistivity of bismuth in this pressure range. Until Zeitlin and Brayman2 reported discontinuities in the resistance of bismuth at these pressures, no one had found resistance discontinuities

Jan 1, 1968