Search Documents

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By D. J. Blickwede

PRESENT knowledge of the effects of time and temperature upon stabilization of the austenite-martensite reaction in steel is fairly complete,1-3 but at the time the work described herein was initiated there was no information about the effects of alloy elements on the phenomenon. However, it has been assumed on theoretical grounds that alloy elements, particularly carbide formers, may have a significant effect on stabilization.' The present work was undertaken to provide information about the effect of two common elements, nickel and molybdenum, on stabilization in hypereutectoid and hypoeutectoid steels. Seven induction-furnace melted, 1.2 pct C steels ' with a variation of nickel from 0 to 6 pct and of molybdenum from 0 to 1.0 pct were used for most of the experiments. Along with these a series of 0.4 pct C steels containing 0 to 6 pct Ni were also studied. The chemical compositions of the steels are listed in Table I. Stabilization in these forged, hot-rolled, annealed, and centerless ground steels was measured by aging brine-quenched specimens (aus-tenite temperature, 1800°F) at 95" and 150°F and then determining the change in specific volume produced by subsequent cooling from room temperature to —320°F.³ In presenting the results the decrease in the change in specific volume, ?V, after various stabilization times is used. This is given by ?V -= ?VO - ?V1 where AVO is the change in specific volume on quenching directly to —320°F and aV, is the change in specific volume on quenching to —320°F after stabilizing for time t. In other words, ?V is a direct measure of the amount of martensite that is lost to the subzero quench as a result of stabilization and hence is greater, the longer the aging time or the higher the aging temperature. The results are shown in Fig. 1. The scatter of the data, which are not shown for clarity and brevity, was sufficient to make the relative location of the curves on the ?V axis inaccurate within ±2x10-5 cc per g. However, some generalities appear which are of interest. Effect of Nickel In the 0.4 pct C steels, up to 3 pct Ni has little, if any, effect on the rate or amount of austenite stabilized at 95°F, Fig. la. Increasing nickel from 3 to 6 pct almost doubles the amount of austenite stabilized in a given time. In the 1.2 pct C steels aged at 95°F, increasing the nickel from 1 to 3 pct appears to decrease the amount of stabilization, and a further increase to 6 pct Ni completely eliminates stabilization as shown in Fig. lb (M, of 6 pct Ni steel was below room temperature). The same behavior was exhibited by these steels stabilized at 1500°F, especially after aging for periods longer than 5 hr, Fig. lc. Thus it appears that up to 1 pct Ni has little effect on stabilization at low or high carbon levels. More than 1 pct Ni increases stabilization at low carbon contents and decreases it at high carbon contents. Ward, Jepson, and Rait5 have found that at inter-

Jan 1, 1954

By C. L. T. Edwards

IN the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on 100 per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blast-furnace charge as good iron as that made without scrap-made with straight ore?" This question may be answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on 100 per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. OPERATION WITH 100 PER CENT STEEL SCRAP During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a 100 per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when l00 per cent steel turnings were charged. Except for occasional charges of nickel scale as an "extra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore-ore and scrap-operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from i00 per cent scrap to the regular burden, the charge hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap charge. The furnace employed had a hearth 16 ft. 0 in., bosh 22 ft. 0 in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter ¾ in., bosh angle 73° 27' and a Baker-Neuman top, with gas-engine blowers. Analyses Range of Material Charged Gravel: Si02, 64.40 to .7o.54 per cent; A1203,3-52 to 4.58; CaO, 7.27 to 9.49; M90, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83.

Jan 1, 1941

By John Porter

(Cleveland Meeting, October, 1912.) Iv taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Effeciency-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-records, clue to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost, sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences.

Jan 4, 1913

By John C. Shyne, Eric R. Morgan

WHEN temper rolled low carbon sheet is stored at room temperature before use, changes take place in its mechanical properties. This phenomenon is known as strain aging. Normally these changes are observed by means of Olsen ductility and Rockwell B hardness tests but' unfortunately such tests are relatively insensitive. Strain aging can be readily observed in the laboratory by means of tensile tests. The tensile test method is even more sensitive if the aging is allowed to take place in specimens which have been prestrained in tension rather than by cold rolling. In fact one of the great benefits of commercial temper rolling is that it introduces a residual stress pattern which tends to mask the effects of strain aging when the sheet is finally used in a pressing operation. Curves B, C, and D of Fig. 1 illustrate the changes that take place during the aging of commercial rimmed steel at room temperature following straining in tension, curve A, Fig. 1. The first important change that can be observed is an increase in the stress required to produce plastic flow. This increase is, in this paper, called the aging index. As aging proceeds and the aging index increases, there is also an observable return of the yield point, an increase in the ultimate tensile strength, and a decrease in elongation to fracture. The results of strain aging in deep drawing steel manifest themselves as stretcher strains (L?ders bands) buckling, 2nd tearing. In deep drawn parts such effects are undesirable and strain aging is a serious problem. The rate of strain aging of a steel depends upon its composition and prior mechanical and thermal history? but for most temper rolled ope

Jan 1, 1958

IN describing the mining and treatment of ore at the Broken Hill Proprietary mine E. J. Horwood, superintendent of mines, gave the following account of the development of flotation there. It was in 1902 that the recovery of zinc from the ore by flotation was hit upon. The former general man-ager, Mr. Delprat, directed our then research officer, Mr. Carmichael, to try boiling the tailing with salt cake of which there was a considerable tonnage left over from the leaching process. The idea was the possibility of dissolving the zinc. Carmichael made the. Experi-ment, but, rather discouraged, took the glass beaker down to the general manager's office, remarking that he could not get the stuff to settle. On showing the beaker to Mr. Delprat, the latter recognized the marked distinction between the black scum on the surface and the rest of the tailings, and exclaimed: "Why, this is the very thing we are after; the zinc is floating!" Patents were applied for at once, but later on it was found that another investigator, Potter, had already hit upon the idea of flotation. His patents, however, were so involved with other operations that his process was impracticable. Litigation followed, but in the end the B. H. P. paid the Potter Company a substantial sum as settlement. In the case of Carmichael's beaker, the acid in the salt cake acted on the small amount of carbonate present in the ore, producing CO. bubbles. Owing to the aversion of sulfide crystals to being wetted, the gas as generated attached itself to the zinc in in-creasing quantities until there was sufficient to buoy the zinc particle to the surface. This action went The next problem was to apply the principle on a commercial scale, and this involved much experiment and developmental work. Various kinds of sloping copper pans with gas jets below to maintain the tem-perature were first tried, but were found too slow and too costly in operation.

Jan 6, 1928

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By Hsun Hu

The formation of annealing textures in high-purity silver, from the various rolling textures obtanled in the course of texture transition, was studied. It was found that from a brass-type rolling texture the recrystallization texture is mainly (120) [211] type, which is quite different from the recrystallization texture of brass. From a predominantly copper-type rolling texture, the reclystallization texture is mainly (100) [001]. The recrystallization texture of silver- varies also with the degree of purity. In each case, however, the reorientation can be expressed as [Ill] rotations of 30° to 40°, which is consistent with the oriented growth theory of the formation of annealing textures. ThE recrystallization textures of rolled silver were studied long ago by Glocker and co-workers (1924-27) and were reported to be (113) [iil] upon annealing at low temperatures.1 Since that time, no further study of the recrystallization textures of silver, particularly with the modern techniques of quantitative texture determinations, has been reported in the literature. In a previous study2y3 it was found that the rolling texture of high-purity silver (99.999 +pct pure) is changed gradually from the common silver- or brass-type to the copper-type by raising the temperature of rolling from 0" to 200°C. The formation of annealing textures from the various rolling textures in the same material is, therefore, of considerable interest. The present paper constitutes the results of such a study. MATERIAL AND METHOD Specimens were taken from the same strips of high-purity silver* that were used previously for

Jan 1, 1962

By E. L. Davis

There have been many attempts to devise formulas for flowing efficiency and flow friction of oil-gas mixtures in oil-well flow tubes. Actually, however, flowing efficiency is rarely any real concern of the oil producer and flow-friction formulas contain so many unknown variables as to be of little, if any value. The production engineer is generally concerned with producing as much oil as possible with a minimum expense per barrel, and with the lowest possible net gas-oil ratio. These ends frequently are opposed to each other and the gas-oil ratio usually is sacrificed. In competitive operations, such as in town-lot fields, high current production is the sole interest. In conservative operation the greatest possible amount of oil obviously should be produced by natural flow unless the net formation gas-oil ratio can be improved by circulating gas. In practice this condition frequently exists. It would be a great advantage if the flowing condition of a well could be analyzed to determine the best possible producing status. Anticipating the death of a well so that gas-lift could be started immediately after the death, or preferably before, would save both production and expense. Frequently it happens that circulating gas fails to help a flowing well, or will not flow it after it has stopped flowing naturally. A knowledge of the laws governing flow would save considerable expense in testing such cases. A predetermination of probable pressures and amounts of circulating gas needed to flow wells and give best possible producing conditions would help in designing compressor installations. The optimum producing status of an oil well generally may be obtained by the conditions that subject the producing formations to the least possible back-pressure. This pressure is made up of the weight of the fluid column, frictional resistance to flow and the reaction from the acceleration of the fluid mass. A mathematical calculation of these components to arrive at a condition giving a minimum summation is impractical. Formulas would be complex and the results untrustworthy because it is impossible to assign proper values to the many variables involved.

Jan 1, 1931

By George J. Bancroft

INTRODUCTION. IT is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Transactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,1 showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny,2 distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many of Prof. Kemp's, ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.5 This theory, dealing with, the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1913

By John C. Calhoun, Frank T. Bethel

Glass beads have been surface treated with Dri-film to render them oil wet by n-octane to varying degrees, and capillary desaturation curves have been determined by the restored state method. The desaturation curves show a regularity of increasing displacement pressures as the oil wetness increases. This has been used to compute apparent contact angles between n-octane and water on glass. The family of desaturation curves also shows a regular crossover, such that the residual wetting liquid saturation values are in reverse order to the displacement pressures. A semi-logarithmic variation is shown between the apparent contact angle and the residual saturation. The desaturation data are interpreted to mean that the wetting liquid ceases to be a continuous phase within individual pores before the capillary pressure can be raised sufficiently to force out the wetting phase completely. The saturation of wetting liquid at which this break in liquid continuity occurs is higher as the oil wetness decreases. INTRODUCTION The petroleum industry has for some time been using measurements of capillary pressures on porous media for research correlations and engineering calculations. It has been generally recognized that the capillary desaturation curve reflects the character and arrangement of the pores within the media and the distribution of fluids within the pores. Methods have been proposed for computing pore size distributions, tortuosity factors. and relative permeabilities from capillary desaturation data.' There is little doubt that the interactions between porous rocks and their contained fluids resulting from surface forces play a dominant role in determining the magnitude and direction of capillary pressure measurements. There have been attempts to introduce as variables two quantities — inter-facial tension and contact angle — generally used to char- acterize surface forces, but in spile of the wide interest in these quantities as important variables, few definite conclusions have been drawn concerning their qualitative or quantitative significance. INTERFACIAL TENSION The interfacial tension appears in a capillary pressure function given by Leverett for correlating capillary desaturation type curves. Use of the interfacial tension in this function seems to be justified by other experiments reported. Apparently, interfacial tensions have little bearing on wetting phase residual by desaturation. CONTACT ANGLE The contact angle was utilized as a variable by Bartell and co-workers"." in tests on displacement pressures, later recognized as the initial point of capillary desaturation. Although Leverett did not include contact angle in his original formulation of the capillary pressure function, later workers suggested its addition. Few reports are available to show variation of residual liquid with contact angle as a result of capillary desaturation.' The problems attendant to measuring contact angle within a porous medium are great. As a consequence of the lack of a concrete approach to a measurement. the workers in this area of research have adopted the general expression of "wettability" to indicate the relative position of two liquids saturating a porous body. It has been shown that gross measurements on porous systems, including capillary desatura-tions, are sensitive to wettability. Attempts at giving a scale to wettability in terms of contact angle through capillary desaturation curves have been made and these apparently are steps in the right direction. In these attempts presence of many other variables precludes attainment of exactness. Also, as a result of other variables, it has been impossible to correlate changes in apparent contact angle with changes in other physical measurements of the systems in question. The present work is an attempt to eliminate as many variables as possible in measuring capillary desaturations resulting from changes in contact angle within a porous medium.

Jan 1, 1953

By Frank A. Linforth

The object of this paper is to present a brief outline of the methods of geologic mapping employed in the Geological Department of the Anaconda Copper Mining Co., at Butte, and to show by means of a few typical examples the practical nature of the results obtained. The extremely complicated geological conditions early encountered in Butte mining led mine operators to realize the necessity of accurate detailed geologic mapping m an aid to successful development of the ore bodies. The organization of the Anaconda Geological Department was undertaken in 1900 by H. V. Winchell, who, in conjunction with D. W. Brunton, worked out the essential methods of procedure which are, in the main, followed at the present time. Since the year 1906 the geologic work has been under the direction of Reno H. Sales, and in some respects the scope of the work has been slightly enlarged. An excellent article describing the general equipment of the geological department was presented by D. W. Brunton at the British Columbia meeting of the Institute in 1905.' His idea, that data collected underground and recorded should be put to practical use and not remain a mere " inventory of the company's underground possessions," is the keynote to the success of applied geology in Butte. The geologic notes are taken as soon as possible after the ground is broken so that any mistake in the mining may be corrected at once, or any particularly advantageous procedure may be suggested before any useless work is done. Taking the notes underground is a comparatively simple matter, but a few necessary precautions may be pointed out. The essential to success is that the notes shall show exactly what geological facts are disclosed. The observer must discriminate carefully between important and unimportant exposures in making the record, especially as regards the relation between veins and stringers, between faults and minor slips, or between the characteristics of veins of different ages. A simple color scheme has been adopted for making this record. Red pencils are used to indicate

Jan 1, 1914

Future of State and Federal Oil Regulation. BY NORTHCUTT ELY (Trans , vol 118 2400 words) The Interstate Oil Compact, ratified by six states and Congress in 1935, replaced the petroleum code, invalidated with other codes by the Schechter decision This compact endeavors, first, to conserve reservoir energy of oil pools through substantially uniform conservation measures by the states, second, it recognizes the state rather than the Federal Government as possessing the necessary police power for that purpose, third, it establishes an interstate advisory commission, so that orderly production in one state is not penalized by uncontrolled production in another, fourth, Federal interests are recognized in the control of hot oil, regulation of imports and fact-finding forecasts of supply and demand by the Bureau of Mmes It is not as complete an instrument as proposed by the Federal Oil Conservation Board in 1932, but is workable, and will be effective in proportion to the support given it by the industry Three results may follow First, now that fear of Federal control has subsided, the industry may lose interest in the compact and let it fall to pieces, second, if vigorously supported by the industry, the compact can accomplish most of the conservation objectives sought by the Federal control measures now believed unconstitutional, third, if the Compact fails, Federal regulation is almost certain to be revived, and can probably be sustained in connection with neutrality legislation, regulation of interstate pipe lines, and coordination of Federal and state gasoline taxes Nearly every step toward governmental regulation has originated within the industry state proration, the Federal petroleum code, Federal control of imports, Federal control of hot oil are examples The Compact shows a trend toward coordination between the powers of the industry, the state government, and the Federal Government If this arrangement fails through lack of interest by the oil industry, the next step is likely to be absorption by the Federal Government of the other two factors involved in the situation

Jan 1, 1937

By Norberto Dominguez

In the year 1820 a commission, assisted by Sr. C. Fernando de Ainada, was appointed by Sr. Jose Ramon Mila de la Roca to report on the condition of the mining region of Parral, in the State of Chihuahua, Mexico, where in recent years the mines of Batopilas have reached an important development under American management. The object of the inquiry was to provide Sr. De la Roca with facts to support a project for reopening mines that two centuries before had produced a large amount of silver. Although this plan failed, many facts of interest in the history of the mines were presented.. Much of the report dealt with questions that had only local application or were restricted to the conditions of labor and equipment in the opening of the nineteenth century. The historical part is presented in the following paragraphs: Abstract of the Report. Notwithstanding the difficulty of forming a just estimate of the system of mines in this mineral group in the valley of Senor Sail Jose del Parral without an examination of each of them, that which we shall say in a general way will suffice to convey an idea of their value and of the urgent necessity of reopening them. If this is undertaken, we believe the results will be of the highest consequence to the Republic, as well as to this immediate locality. The group of the Villa del Parral covers the mineral territory in which the village of that name was located. Its moantains contain large metallic veins, from which, as from the trunk of a tree, depend others much more slender, locally called ,fibras, crossing and interlacing each other in many directions. The first and oldest of these very rich deposits of gold

Jan 1, 1902

By Duncan MacVichie

The iron fields described here are located in the Iron Springs and Pinto mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100 during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,' who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply farther away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 1, 1927

By Henry Hibbard

THE process of making washed metal now followed is in principle that described by Holley before this Institute in 1879, as the Krupp washing process. Sir Lowthian Bell also experimented extensively in England during 1877 and 1878 on refining iron and joined his interest with Krupp, the process being often referred to as the Bell-Krupp process. The only plant in this country now operating this process is that of the Brier Hill Steel Co., Youngstown, Ohio. This process may be considered as the sole survivor of the numerous methods conceived for refining crude iron, when the removal of phosphorus from steel-making material was the great desideratum affecting large districts. The east coast of England and all northern Germany, the homes of Bell and Krupp, respectively, could at that time make steel only from imported ores. These processes were in use or in various stages of development 40 years ago and all except the Bell-Krupp received their quietus from the development of the basic steel processes, both pneumatic and open hearth. The aim of the early refining processes was, first, the removal of the silicon; which could be clone on a sand bottom, and later, the removal of the phosphorus, requiring a bottom which would give or permit a basic slag. The incidental advantages of increased yield and small fuel consumption were not generally recognized or considered; the aim of the later. operations was the saving of the difference in value between low and high phosphorus irons, as well as hastening the removal of the metalloids. The chemistry of the washing process follows in part that of the puddling process, and indeed washing might, be considered as the first half of puddling, since all the non-ferrous elements of the crude iron, except the carbon, are eliminated and the iron is maintained molten until cast. In puddling, the iron loses its carbon as well, and because of that, its fusion point rises above the hearth temperature; it freezes into a pasty malleable form, and is worked at once by squeezer, hammer, or rolls.

Jan 12, 1915

By W. H. Triplett

THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno, y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold. mines are situated a few kilometers to the southeast on the same mountain range near Concepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burckhardt, E. Böse, L. B. Kellum, .and R. W. Imlay. Carlos Burckhardt who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1952

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By William S. Hannan, H. Rush Spedden

FLOTATION may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. PROBLEM Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions will result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. PRESENT THEORIES Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles. Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor of this theory is the difficulty in the flotation of fines. If attach-

Jan 1, 1947

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946