Search Documents

By A. Q. Tool

THE necessity of accurate temperature measurements in the glass-making industries is today being much more widely appreciated than in the past. The introduction of the modern simplified and perfected pyrometric methods in connection with exact regulation of furnace temperatures has caused a marked improvement in the glass product with a quickened rate of production. An example of the processes in which much improvement has been and still can be made is that of annealing or heat-treating the glass. This is one of the most delicate processes in glass manufacture and one that requires a most careful furnace control. The heat treatment is undertaken to decrease the possibility of breakage and, in glass for fine optical instruments, to prevent serious warping of accurately ground and polished surfaces and to make the glass more uniform throughout to the passage of light waves. These objects are accomplished by removing all the harmful stresses that exist in a piece of glass when it has been cooled too quickly or unevenly. Such stresses exist, for example, after it has been pressed, cast, or otherwise worked. Thus the process of annealing consists of heating the glass evenly to the temperature at which it softens just enough to relieve these stresses in a reasonable time and then cooling slowly and uniformly until the glass hardens again. Accordingly, the things that must be investigated and determined in order to anneal glass without loss of time are, the annealing temperature, the time that the glass should be held at this temperature while the stresses relax, and the quickest cooling procedure that will give satisfactory results. After these characteristics of the glass are known the problem is one of pyrometry and temperature control entirely. In cases when it is known that a glass article will be required to withstand some definite type of heat or mechanical shock it is often possible, by a proper heat treatment, to produce such a distribution of the stresses in the glass that it will be enabled to resist these shocks more effectively.

Jan 9, 1919

By G. P. Walters, W. C. Fuller

THE production of thin films of beryllium became essential early in the irradiation program at Harwell in order to study the fundamentals of irradiation damage in this metal. In common with other metals, electron-microacope specimens of beryllium can be produced by different techniques. The techniques used to produce thin-film specimens varied according to the starting material. Most of the starting material was -0.060 in. thick. Large-area specimens (1 in. long by 0.5 in. wide) were chemically thinned to -0.005 in. thick in a solution containing 85 pct orthophosphoric acid, 10 pct chromium trioxide, and 5 pct sulfuric acid at 70°C prior to electropolishing. Small-area specimens, Fig. 1, had to be mechanically thinned prior to electropolishing because chemical thinning considerably reduces the area as well as the thickness. Mechanical thinning tends to produce a worked layer about 0.002 in. deep and hence this method cannot be used to thin bulk specimens below about 0.005 in. thick. Mechanical thinning is carried out by mounting the specimen on perspex then carefully polishing on wet grinding papers. Polishing is continued until about half the initial thickness is removed; the reverse side is then polished in a similar manner. After the bulk specimens have been mechanically or chemically thinned to -0.005 in. they are elec-tropolished in the solution shown in able I at 50" to 80°C. This solution should be prepared by adding the chromium trioxide to the orthophosphoric acid and then the glycerol last. The glycerol should be added slowly because a vigorous effervescence can occur. Electropolishing is carried out by holding the specimen in stainless-steel tweezers and gently agitating in the solution. Masking or "window" techniques are not required for beryllium, good microscope specimens being obtained from the edges of elec-tropolished foils. A stainless-steel beaker should be used, acting as the cathode and solution container. A closed circuit voltage of 30 v is used for polishing. Too low a voltage produces a matt surface and pitting occurs when it is too high. The solution temperature is important. If it is too low, the solution is viscous and bad polishing results and, if too high, etching of the specimen occurs. After electropolishing, the foils are thoroughly

Jan 1, 1963

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968

UNDER the same justification that I spoke to you in the preceding chapter on crystal and some other gems, I can now speak much better and with much greater reason of glass, since it is one of the effects and peculiar fruits of the art of fire. Every product that is found [41v] in the interior of the earth is either stone or metal or one of the semiminerals, and glass, as is seen, resembles them all, although in all respects it is dependent upon art. Therefore it seems to me that before coming to the discussion of the arts themselves, I must treat of this very beautiful composition created by art and number it with the semiminerals. Thus in this chapter I shall speak to you of glass, not as a proper semimineral, nor yet as a metal, but as a fusible material that is almost made mineral by art and by the power and virtue of fire, born from the speculation of good alchemistic savants, through whose efforts it imitates. the metals on one hand and the transparency and splendor of gems. on the other. Certainly it is a very beautiful thing and one that should not be left buried in silence, in consideration first of how great a thing art has been, able to discover, and then because its beauty makes it such a pleasing thing for making drinking. glasses and an infinite number of other ornamental things that satisfy the desires of man. I shall begin, then, by telling you, to the credit of the alchemists, how I believe that this thing was found through their desire to make gems; for when they could not bring them to perfection (as also happened with the metals) they made this beautiful and attractive product, glass. However, Pliny says that it was found by chance in Syria at the mouth of the Belus River by certain merchants who were driven there by the fortunes of the sea and forced to stop and disembark there for a time in order to eat. In cooking the food they saw the rocks of that place converted into a flowing, lustrous material. And as they thought about this, it seemed beautiful to them, and when they went away they carried some stones and plants with them. Thus they gave beginning to glass making. But now leaving this discussion it does not matter how it may have been discovered, whether by merchants or by ingenious alchemists. Art is that which has given it being, through many experiments and by addition

Jan 1, 1942

By E. J. Schmitz

This novel safety-lamp, which was first introduced in some of the German coal-mines in 1882, at once attracted general attention in the coal-districts of Europe. Objections which arose during the early stages of its use at the mines have gradually died away with the increase of experience in handling the lamp 011 the part of the miners, and the continual efforts to perfect it on the part of its inventors. Wolf's lamp has rapidly surpassed all its rivals, and has already a greater distribution on the Continent than any one of its older sisters. In the course of two and a half years, the manufacturers have sold 25,000 of the lamps, besides remodelling several thousand rapeseed-oil lamps. This great success, which of itself speaks loudly enough as to the superiority of the Wolf benzine-lamp, is corroborated by both official and private reports, which all agree in pronouncing this lamp the best yet brought forward. It was described in a paper by Mr. Eugene B. Wilson, read at the Chicago meeting of the Institute, in May, 1881,* in which its salient merits were briefly but clearly indicated. Every previous improvement of the original Davy lamp has been directed to one or more of the following main points: 1. Light of greater and more uniform intensity. 2. Freedom from smoke or soot, which clogs the gauze and other parts of the lamp. 3. A greater safety and sensitiveness in the presence of firedamp. 4. An illuminating material which, satisfying the foregoing conditions, should be also cheap. 5. A lock which could not be opened in the mine by the miner. 6. An arrangement for lighting without opening the lamp. 7. An arrangement for changing the size of the flame in the closed lamp, to supersede the picker, the danger from which is explained in Mr. Wilson's paper, already cited. It may safely be said that wolf's lamp was the first to secure all these objects. The adoption of benzine instead of rapeseed-oil (previonsly the best illuminant) has completely satisfied conditions 1, 2, 3, and 4. Benzine gives a much clearer, stronger, and more uni-

Jan 1, 1886

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 ('other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By Ralph H. Sweetser

AT the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rejections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blast furnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By A. W. Edelen, H. V. Lee

THE Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. In the ore lenses the sulphides appear as a massive, very he-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. INTRODUCTION The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre- Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Teziutlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short line, Shay-geared locomotives are used for the transportation of concentrates and supplies.

Jan 1, 1937

By A. F. Taggart, F. E. Beach

The flotation process for the concentration of ores is a method by means of which one or more of the minerals in the ore (usually the valuable ones) are picked up by means of a liquid film and floated at the surface of a mass of fluid pulp. Here they are separated from the other minerals, which remain immersed in the body of the pulp. In general, the minerals which are floated are sulphides of metallic luster, but some other minerals of metallic luster such as graphite and some sulphides with adamantine luster, such as sphalerite and cinnabar, are amenable to treatment by the process. The importance of flotation lies in the fact that it is primarily a "slimes process" by means of which the particles of valuable mineral, too fine for efficient gravity concentration, are saved with a high percentage of recovery. Recoveries in the mills treating low-grade copper sulphide ores have been advanced 10 to 20 per cent. by the installation of the process and similar increased savings have been accomplished by the same means in mills treating sulphide ores of zinc and lead. When finely ground ore containing sulphides mixed with a siliceous or earthy gangue is brought gently onto the surface of a body of water, in a direction forming an acute angle with the surface of the water, a considerable portion of the sulphide constituent of the ore floats on the surface of the liquid, while the gangue sinks. This is the so-called film flotation, exemplified by the Wood and Macquisten processes. When gas bubbles are introduced into a fluid pulp composed of finely ground ore and water, to which has been added (1) a small amount of certain oils, or (2) a small amount of certain acida or acid salts, or (3) a small amount of certain alkalis or alkaline salts, or (4) a small amount of a mixture of oil with acid or alkali, the sulphide particles in the ore are brought to the surface on the gas bubbles. These collect in a froth

Jan 1, 1917

By R. L. Huntington, Frank P. Vance, George F. Russell, Robert Thompson

With the advent of higher pressures in the operation of natural-gas transmission lines, the removal of water vapor from the gas has become increasingly important in order to prevent condensation or formation of gas hydrate from slowing down or stopping the flow of gas. Intelligent design of these dehydration or gas-drying plants has been hampered through the Iack of experimental data on the water vapor content of natural gas at elevated pressures. In view of this need, this present investigation was sponsored by the Southern Natural Gas Co. in the Chemical Engineering laboratories at the University of Oklahoma Research Institute. Experimental results were obtained on the water-vapor content of natural gas up to 2000 lb. per sq. in. at atmospheric temperatures. The water content at 2000 lb. is approximately two thirds as much as it is at 1000 Ib. Deviations from the ideal gas laws vary directly with pressure and indirectly with temperature. Introduction The removal of water vapor from natural gas is an important operation in connection with the production and transportation of this commodity because: I. Liquid water accelerates internal corrosion of a pipe line. 2. Accumulation of water at low points in a pipe line reduces markedly its capacity. 3. Gas hydrates, icy snowlike growths, form readily under high pressure in the presence of the lower hydrocarbons and water, often plugging up the pipe line. In order to design dehydration plants for stripping the gas of its water content, it is essential that the engineer. have a knowledge of the saturated or equilibrium water-vapor content of the gas to be processed. With the gradual increase of operating pressures around gas-producing wells and pipe lines, it was observed that the quantity of water recovered from dehydration plants or condensed in colder lines was considerably greater than had been expected from calculated contents, based on vapor-pressure data taken from steam tables. This observation prompted a number of investigators, for instance, Laulhere,3 Dea-ton,l and Hammerschmidt2 to carry out experimental work at pressures up to 600 lb. per sq. in. in order to determine quantitatively the water content of various gases. Sage, Lacey, et al.4,5 have recognized more recently the need for such data at higher pressures, but their work was done at temperatures of 100ºF, and higher. Since hydrate formation usually, if not entirely, occurs at temperatures below 100ºF., the present investigation was confined to the . lower temperature range at pressures from 600 to 2000 lb. per sq. in. gauge.

Jan 1, 1945

By E. S. Bardwell

The reverberatory copper-refining furnaces at the Great Falls Reduction Dept. of the Anaconda Copper Mining Co. have used successively as fuel, lump coal on grates, pulverized coal, oil and natural gas. In no other plant, so far as can be ascertained, has such a variety of fuels been used. This fact affords a unique opportunity for comparing the relative efficiency obtained with these several fuels under nearly identical conditions. Furnaces The present furnace refinery at Great Falls was placed in operation in April, 1916. The original installation consisted of two furnaces, each with hearths 36 by 14 ft. and provided with fireboxes 10 by 12 ft. for firing lump coal on grates. These furnaces had air-cooled sand bottoms and chrome-brick side walls both above and below the metal line. The roofs were of 12-in. silica brick. Each furnace was provided with a waste-heat boiler of approximately 400 boiler-hp. capacity. We soon found that chrome brick was very unsatisfactory as side-wall material because of its excessive spalling. At the first opportunity the furnaces were rebuilt, using magnesite brick below the metal line and silica brick from the metal line to the roof. At the same time the thickness of the side walls was increased, thus decreasing the width of the hearth to 13 ft. At about this time also, the thickness of the furnace roofs was increased from 12 to 15 in. No further changes occurred in furnace design until 1922, when the use of lump coal on grates was abandoned in favor of pulverized coal. The first charge to be melted and refined with pulverized coal was cast on March 30, 1922. When pulverized coal first was used the burner pipes were introduced directly into the firebox as it was felt that some kind of a combustion chamber might prove necessary, but this was not needed. The fireboxes were dismantled and the burners introduced through openings directly over the bridge wall. During the summer of 1922 one of the furnaces was completely rebuilt, lengthened 10 ft. and provided with a silica-brick bottom in the form of an inverted arch. At

Jan 1, 1934

By J. E. Lawrence

Copper-decorated lattice disorders in silicon have been analyzed by electron transmission microscopy, chemical etching, and P-N junction reverse current measurements before and following different gettering treatments. Lattice disorders acted as the nucleating sites for copper precipitation. Copper precipitates in silicon resist chemical etching, absorb electron beams more than silicon, and cause excess reverse currents. Totally gettered disorders will chemically etch rapidly, be transparent to electron beams at extinction contrast, and not contribute to excess reverse currents. Three different gettering procedures were performed to determine the effectiveness of different EXTRANEOUS metal contamination can alter the minority carrier lifetime and resistivity of bulk silicon as well as cause excessive reverse currents in semiconductor devices. Previous workers have reported such activity for gold,1,2 copper,'-* iron,' and rnanganese.2,5 Gettering is a method employed to render these impurities electrically inactive. However, some property of the junction-degrading metals prevents gettering procedures from being wholly reliable. The comparative effectiveness of gettering with different agents has been the topic of earlier publications.2,3,6-11 Two mechanisms for gettering metallic impurities have been proposed: the distribution coefficient mechanism by Thurmond and Logan7 and the compound formation mechanism by Goetzberger and Shockley.2 Both of these models evolved from data gettering mechanisms. First, phosphorus was allowed to enter a protective SiO2 film but remain away from the Si-SiO2 interface to test the effectiveness of the compound formation gettering mechanism. Second, phosphorus was allowed to enter the backside of silicon wafers to test the effectiveness of the lattice strain gettering mechanism. Finally, nickel was diffused into the backside of silicon wafers to test the effectiveness of the distribution coefficient gettering mechanism. In each case, copper precipitates dissolved as a result of the gettering treatment. Tightly packed precipitates will resist gettering more than loosely packed copper precipitates. acquired by the electrical analyses of gettered semiconductor materials. An electrical analysis, however, cannot identify the fate of the gettered metals. The radiotracer technique has recently been applied to determine the redistribution of metals following different gettering treatments.3,9,10 The spatial resolu tion of the radiotracer technique prevented the analysis of metal precipitates which contribute to the excessive reverse currents of P-N junctions. The gettering processes employed by the earlier workers, almost without exception, allowed the gettering agent to enter the silicon lattice. This procedure makes it quite difficult to differentiate between the distribution coefficient and the compound formation mechanisms. The metallographic analysis of gettered copper precipitates discussed in this work supplements the earlier work by obtaining direct evidence of silicon lattice defects decorated with copper before and following different gettering treatments. The effectiveness of a process which restricts the gettering agent, phosphorus, to a dielectric film and thus away from the silicon lattice is discussed in addition to the ef-

Jan 1, 1969

By T. A. Dungan

The thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbo-thermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was' expected to obtain metallic magnesium. The results were positive and metallic magnesium was .0

Jan 1, 1944

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By P. H. Bohart

THe answer to the title question will be found by considering the ultimate influence of the petroleum engineers on industry and by considering the tools with which petroleum engineers must be equipped. Some 2000 to 3000 petroleum engineers are being absorbed by the industry yearly, indicating the magnitude of influence which they may exert on the industry. The petroleum industry is a highly technical one and it is inevitable that management be entrusted more and more to executives with technical training. The industry, therefore, expects the petroleum engineering schools to provide a broad basic training and a social and economic orientation which goes beyond merely supplying the minimum technical qualifications necessary to discharge responsibilities for a particular job. Because of the many branches of industry, emphasis must be placed on the Student's being trained in fundamentals, as well as grounded in other engineering branches, such as mechanical, civil and electrical engineering. The petroleum engineering graduate must know how to outline and organize the material for an engineering report and should be thoroughly grounded in English, both written and spoken. Even to the end that a five-year course may be required, they should receive instructions in auxiliary cultural and social science courses, industrial relations, and public speaking. Training in the method of approach to an engineering problem is something in which industry is deeply interested. A standard of ethics, a desire to arrive at the truth, and leadership training should be stressed. Introduction The basis of an an to any ques- tion concerning the petroleum engineering schools' responsibility to the industry will be found by considering the ultimate influence of the petroleum engineers on the industry and by considering also the tools with which petroleum engineers must be equipped in order to achieve success and happiness in the role in which their training, individual talents and choice of a profession ultimately will cast them. The problem must always be considered as it relates to a large group and not as it relates to a particular individual possessing strong natural talents and destined, by virtue of them, to pursue a certain course. The question implies that petroleum engineering schools have a responsibility, and indeed they do, not only to the industry but also to the students and even to the public. Because the responsibility is concentrated in a relatively few schools whose graduates are absorbed largely by the one industry, the responsibility is more apparent and the effect of failure to discharge the responsibility fully is more serious than the effect of similar failure on the part of schools supplying a smaller portion of the industry's intake of engineering graduates. This fact is especially true with respect to an industry such as the petroleum industry whose ratio of technical to nontechnical employees is relatively high and is increasing.

Jan 1, 1948

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorinationt of olivine has two major defects: (I) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatments and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By P. H. Bohart

THe answer to the title question will be found by considering the ultimate influence of the petroleum engineers on industry and by considering the tools with which petroleum engineers must be equipped. Some 2000 to 3000 petroleum engineers are being absorbed by the industry yearly, indicating the magnitude of influence which they may exert on the industry. The petroleum industry is a highly technical one and it is inevitable that management be entrusted more and more to executives with technical training. The industry, therefore, expects the petroleum engineering schools to provide a broad basic training and a social and economic orientation which goes beyond merely supplying the minimum technical qualifications necessary to discharge responsibilities for a particular job. Because of the many branches of industry, emphasis must be placed on the Student's being trained in fundamentals, as well as grounded in other engineering branches, such as mechanical, civil and electrical engineering. The petroleum engineering graduate must know how to outline and organize the material for an engineering report and should be thoroughly grounded in English, both written and spoken. Even to the end that a five-year course may be required, they should receive instructions in auxiliary cultural and social science courses, industrial relations, and public speaking. Training in the method of approach to an engineering problem is something in which industry is deeply interested. A standard of ethics, a desire to arrive at the truth, and leadership training should be stressed. Introduction The basis of an an to any ques- tion concerning the petroleum engineering schools' responsibility to the industry will be found by considering the ultimate influence of the petroleum engineers on the industry and by considering also the tools with which petroleum engineers must be equipped in order to achieve success and happiness in the role in which their training, individual talents and choice of a profession ultimately will cast them. The problem must always be considered as it relates to a large group and not as it relates to a particular individual possessing strong natural talents and destined, by virtue of them, to pursue a certain course. The question implies that petroleum engineering schools have a responsibility, and indeed they do, not only to the industry but also to the students and even to the public. Because the responsibility is concentrated in a relatively few schools whose graduates are absorbed largely by the one industry, the responsibility is more apparent and the effect of failure to discharge the responsibility fully is more serious than the effect of similar failure on the part of schools supplying a smaller portion of the industry's intake of engineering graduates. This fact is especially true with respect to an industry such as the petroleum industry whose ratio of technical to nontechnical employees is relatively high and is increasing.

Jan 1, 1948