Search Documents

By D. J. Carney, E. C. Rudolphy

Large macroscopic nonmetallic inclusions were related to altered fireclay refractories by chemical and microscopic means. Pouring refractories are discussed as a source of these large inclusions. Nozzles and wells are major contributors. Use of alkali and titania contents as tracers is described. Recommendations are offered to minimize the sources of inclusions from pouring refractories. IN any attempt to improve the cleanliness of plain carbon and alloy steels, consideration must be given not only to the proper deoxidation practice to minimize inclusions, but also to sources of inclusions from pouring refractories. In some cases, the inclusions resulting from deoxidation may be minor in amount, yet a relatively dirty steel may be produced as a result of improper care in the pouring practices for the steel. The number of studies of inclusions resulting from pouring refractories has increased recently and some excellent reports on this subject have already been published.'4 Some of these reports were reviewed briefly in a companion paper by M. P. Fedock.5 Mr. Fedock's contribution is a fine addition to the studies necessary to improve steel cleanliness for the ultimate benefit of all steel producers and consumers. In the interest of constantly improving cleanliness, the authors have been actively engaged for the past two years in experimentation to determine more closely the sources of inclusions in steel. One phase of this work was associated with efforts to define more closely the sources of macroscopic inclusions which have been experienced on occasional heats. The term "macroscopic inclusions" is defined in general as those inclusions which are visible to the naked eye or at low magnifications of the order of less than X25. These inclusions sometimes can be seen in the macro-etch tests of billets and slabs. This report summarizes a few of the field experiments and laboratory studies conducted at the South Works of the United States Steel Corp., which were made regarding nozzles, wells, and ingot scums, as well as inclusions occurring in steel products. The data in the present study, together with the data of Mr. Fedock concerning ladle erosion, should be of value in regard to future studies of inclusions arising from pouring refractories. The knowledge gained as a result of data collected thus far at South Works has been helpful in improving the cleanliness of the products and in pointing the way toward further improvements. Similarity of Large Inclusions to Refractories and Altered Refractories In the routine inspection of billet etch tests, occasional inclusions visible to the naked eye have been observed. These large inclusions most frequently occur near the top of the ingot and near the billet surface. When such material was encountered, careful examinations were made in an attempt to determine the origin of these inclusions. In a relatively few cases, examination revealed that the material was unaltered fireclay refractory of a type similar to that used for hot-top material, with only the surface of the inclusions having an altered appearance under the microscope. However, the great majority of these inclusions were completely altered-refractory material. The term "altered refractory" is defined

Jan 1, 1955

By Wallace W. Key

Chalk is a natural calcium carbonate occurring as the remains of soft, friable, minute marine organisms. Whiting can be either finely ground calcium carbonate prepared from chalk, marble, or limestone or the product obtained by chemical precipitation from a solution or suspension containing lime. Until relatively recently, whiting made from limestone was termed "whiting substitute," but it is now usually designated as limestone whiting. Precipitated calcium carbonate, sometimes called "precipitated whiting" or "precipitated chalk," is a finely divided calcium carbonate product obtained by chemical precipitation from a solution or suspension containing lime. Considerable quantities of precipitated calcium carbonates are produced from many chemical processes. Naturally occurring calcium carbonate in a variety of crystalline forms and in all degrees of chemical purity forms a substantial part of the earth's crust. Exactly where a chalk grades into a marl or calcareous shale through increase of clay or silt or into a hard limestone through consolidation and crystallization is difficult to determine because no rigid specifications have been promulgated for classifying them. Composition and Properties Once considered to be amorphous, chalk was later found to be cryptocrystalline. In the pure state it consists entirely of CaCO3, but many deposits are impure. When impurities are removed and the material is reduced to a finely divided state, it is known as chalk whiting. Much confusion attends the use of the term "chalk" as well as the classification of whiting materials. For instance, blackboard chalk is not necessarily chalk but is sometimes plaster of paris or a form of talc. Colored "chalks" may be true chalk colored and compressed with a binder but are probably such materials as hematite, clays, or carbonaceous matter. The term whiting was applied exclusively to the product derived from true chalk before World War I. Chalk imports were difficult to acquire during World War I, and whiting substitutes, a term applied to the products derived from natural rock deposits and precipitated calcium carbonate, were introduced. Substitute whitings were not acceptable at first, but it was found that blending true chalk with substitutes often created an improved product; eventually by selection of limestone and finer grinding, products not only acceptable, but for some uses superior to chalk whiting, were developed. Gradually the term "substitute" was dropped because chalk whiting had lost its importance, being largely supplanted in the United States by other whiting materials. Whiting is now made in ever-increasing quantities from limestone, marble, dolomite, marls, vein calcite, oyster-shell, as well as primary and byproduct precipitated calcium carbonates. Distribution of Chalk Europe-In England, France, Belgium, Denmark, and other European countries highpurity chalk occurs in extensive beds. The Cretaceous period, or the "age of chalk," in geologic history receives its name from the great deposits of chalk exposed on either side of the English Channel. It has been estimated that oceans in which chalk and allied deposits were formed covered more than 500,000 square

Jan 1, 1960

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,' but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick's law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

M. G. CORSON.'-I am not going to discuss any of the papers presented but merely the question of season cracking of brass in general. Alpha brass has been known for nearly 500 yr. and from the very beginning a number of articles were made from sheets of this alloy by the process of spinning. Metal turning lathes were not yet known but wood turning lathes already existed and the wood turners used to make the mandrils and do the brass spinning themselves. Cases of season cracking were known even then. In 1915 I was connected with a small company doing a certain amount of brass spinning. Before the war its products never gave cause for complaint but their war-time products were cracking too frequently. The reason was, that due to the exigencies of war an excessive speed-up was attempted and the material simply could not take it. Today corrosion cracking of brass is most important in the case of cartridges for small arms ammunition and shell cases for large guns. The cracking takes place in storage and too frequently it is explained by the hypothetical presence of vapors of ammonia. However, I had the experience of purchasing some 20,000 rounds for the old Vetterli rifle from the Swiss government in 1905. The rifle and the cartridges were obsolete for many years and those which I bought were stored for at least 10 yr. None of them was found to be cracked or to crack in use. And the reason again was in the amount of work used in manufacturing the cartridges between anneals. The machinery today is more powerful and the amount of

Jan 1, 1945

By B. B. Betty

H. L. Burghoff.*—Have the authors any information on the effect of grain size in these materials? There is a material difference in the grain sizes shown for the Monel and the Inconel. Is a wide range of grain size normally found for each material, and, if so, what is its effect upon creep strength? 11. L. Eiselstein.—The grain size for Monel shown in the micrograph is the usual size found in that product. The grain size of Inconel is about the same as that, too. However, we have run tests on Inconel at higher temperatures than those reported in this paper, and have found that the coarser grain size has a better creep resistance; and that the grain size that gives the best creep resistance at 1600°F. is about 0.005 in. in diameter. We have no test on Monel with varying grain size. J. J. KANTER.†-It has been known for a long time that Monel metal exhibits ductility anomalies at elevated temperatures. Even in short-time test, it can be demonstrated in the range of 900°F. that there is a distinct falling off of the ability of Mone1 metal to elongate, and in rupture tests this shortcoming is still further accentuated. Knowledge of this rupture anomaly of Monel metal may be one of the reasons for which designer's approach certain high-temperature applications with reservations. The authors of this paper have merely demonstrated that for 900°F. the alloy has an ability to elongate 1.7 per cent over a period of some 2700 hr. Before any conviction can be expected from designers that Monel metal is applicable to stress design in such range of temperature, I think it is desirable to demonstrate the capacity for the material to elongate over a longer period of time than has been done in this presentation.

Jan 1, 1945

By L. A. Tarshis, H. E. Cline

A stability criterion for a lamellar eutectic interface was derived previously1 assuming that the wavelength, A,. of the perturbation which grows most rapidly is much larger than the lamellar spacing. A. This assumption was required to permit averaging of both the interface temperature and composition over the complicated geometry of a lamellae. If this assumption is invalid, as has been suggested.2,3 then the problem becomes too complicated to solve completely. The first of these analyses1 did not calculate the wavelength. A,. of the initially unstable perturbation. whereas the more recent analysis.' which led to a contradiction of this assumption. did not include one of the key factors for determining this wavelength. To rigorously determine the wavelength, the effect of the curvature of the perturbed interface (not considered by either of the above treatments) must be included. By omitting this term, one would be led to an incorrect conclusion regarding the magnitude of A,. but to an accurate criterion for stability as evidenced by the excellent agreement with experimental observations.' In the case of single-phase alloys. the critical wavelength. A,. for instability can be calculated from the Mullins and Sekerka4 (M.S.) analysis which includes the effects of capillarity. In the following discussion, the M.S. analysis is applied to lamellar eutectics and the critical wavelengths calculated for reasonable growth conditions in Pb-Sn eutectic alloys. In order to apply the M.S. analysis to eutectics. one may substitute i) the effective liquidus slope.1 m*. for the single-phase liquidus slope and ii) the ratio of the bulk alloy composition. C,. to the average interface composition in the liquid (Ci = CE where CE is the equilibrium eutectic composition) for the distribution coefficient to give:

Jan 1, 1970

By Charles Larkey

NUMEROUS papers have been published on the use of graphic methods to determine the best curve to be used in estimating the production decline of oil wells but, as far as the writer has been able to ascertain, nothing has been published dealing directly with the subject as to how curves may be worked out mathematically, which will conform most closely to the production data under consideration in any given instance; hence the writer has endeavored to show by means of a few concrete examples just how such appli-cation can be made. Among valuation engineers, two types of curves are in current use for the representation of the decline in production of oil wells. One may be represented by the equation, y = krx, sometimes known as a percentage curve, for the reason that the production for any period is multiplied by a constant rate or percentage to obtain the production for the succeeding period. This curve appears as a straight line on semi-logarithmic cross-section paper. The other curve may be represented by the equation, y = kxn, and is shown as a straight line on logarithmic cross-section paper. In each of these equations, y represents the number of barrels produced over a given period of time, and x the successive periods of time. The other letters are constants to be determined for each well or group of wells considered in arriving at the most probable curve to represent the rate of production for a given property; from which the underground reserves may be estimated by extrapolation, or the extending of the curve beyond the last known period of production to show the most probable production values for the future.

Jan 7, 1923

By D. R. Spink

In the preparation of zirconium and hafnium metals, there are many indications that impurity levels control the physical and chemical properties of the metal. The purpose of this work was to develop methods of producing pure raw materials that could be reduced to highly pure metals. Early work by the Carbomcndum Metals Co. and others indicated that certain fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. We have developed workable fused salts along with a continuous and higly efficient scrubber design which can be used to produce very pure zirconium tetrachloride. Metal made from the purified tetrachloride has been shown to approach crystal bar metal in purity. Scrubber designs are discussed with recommended materials of construction. VARIOUS methods have been used to purify zirconium (and hafnium) tetrachloride. Most of these methods involve thermal degassing initially (the removal of more volatile compounds at temperatures below that where zirconium tetrachloride exhibits a significant vapor pressure) followed by a sublimation step (which conveniently leaves the nonvolatiles behind.) While these procedures effect definite purification, such processing is batchwise and does not result in optimum purification. Early work by The Carborundum Metals Co. and others indicated that fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. The objective of this work was to develop a continuous fused-salt scrubbing process that would yield high-purity zirconium and hafnium tetrachlorides. The term "fused salt" refers to the molten state of ionic compounds and as used here, specifically refers to alkali metal and alkaline earth halides. Fused salts, because of their many valuable properties, are becoming increasingly im- portant industrially. These valuable properties of the fused salts are: 1) stability at elevated temperatures; 2)low vapor pressure; 3) low viscosity; 4) ability to dissolve many different materials; and 5) good elctctrical conductivity. All but the last property enhances the use of fused salts as scrubbing agents for zirconium and hafnium tetrachlorides. Fused-salt scrubbing may be defined for our purpose as the intimate contact between a gaseous compound and a molten salt with the purpose of removing impurities from the gaseous compound. In this case, the gaseous compound is zirconium tetrachloride which submlimes at 331°C. When this gas is contacted with a molten salt, impurities such as aluminum, iron, and titanium are removed and the resulting product is considered fused-salt scrubbed. Zirconium and hafnium are sold to a purity specification. Generally speaking, normal production without scrubbing is capable of meeting specifications. There are, however, several considerations That make the knowledge of methods of additional purification highly desirable. These are: 1) the control of product analysis; 2) the production of a pure product for special applications; 3) the salvaging of off-specification material; and 4) the use of raw materials with higher impurity levels than 1 he present raw materials. You will note that items 1 and 2 are somewhat complementary to each other and that item 4 assumes that The present process has impurity removal limitations. To better understand the part that fused-salt scrubbing of zirconium tetrachloride plays in the manufacture of zirconium, Fig. 1 contains an illustrated flow sheet of the industrial production of zirconium metal. In referring to Fig. 1, we can point out the specific benefits derived from our ability to purify zirconium tetrachloride. Purification of the crude (hafnium-containing) zirconium

Jan 1, 1962

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By R. F. Krueger, L. C. Vogel, P. W. Fischer

Previous studies have shown that the permeabilities of sandstone cores are markedly reduced following exposure to drilling fluid and subsequent clean-up with oil at high-pressure gradients. Laboratory experiments reported in this paper indicate that permeability damage from drilling mud or water can be substantially avoided through use of an initial low-pressure gradient followed by gradually increasing gradients during clean-up by reverse oil flow. On the other hand, attempts to improve the permeability of damaged Berea and oil formation cores with high-rate oil backflush (simulated well stimulation) and low-rate clean-up gave erratic results. Essentfully complete permeability repair was achieved in most of the fresh water-damaged cores from Miocene and Pliocene oil-producing formations; only minor improvement was noted generally in tests with both water-and mud-damaged Berea sandstone. Field well stimulation treatments using high-rate back-flush resulted in long-term productivity improvement when production was brought in at gradually increasing production rates and then restricted to a steady value less than the maximum possible rate. Wellbore plugging at high production rates correlated with increasing solids content in the produced oil. Observations and results from these tests agree with current concepts that formation damage in water-sensitive rocks results from movement and bridging of formation fines, rather than from clay swelling alone. INTRODUCTION Many laboratory studies1-g have shown that the permeabilities of sandstone cores are often markedly reduced following exposure to fresh water or water-base drilling mud filtrate. However, work with cores in the restored state has demonstrated that, although permeabilities to water may be very low for sandstones containing hy-dratable clays, flow of oil can often restore a substantial portion of the effective permeabilities to oi1.Neverthe- less, water invasion into water-sensitive sandstone cores results in varying degrees of permanent reduction in permeability to oil.24' Based on field data, Wade's statistical study" of well completion effectiveness also indicated a correlation between productivity damage and water invasion during completion. Similar damage can result from fluid invasion during workover. Nowak and Krueger' and Bertness4 observed in their early work (1951-53) that formation damage in water-sensitive sandstones was associated not only with swelling of expandable clays but also with movement of dispersed particles. Subsequent work by Monaghan et al." (1959), Atwood'' (19641, Mungan" (1965) and Gray and Rex'" (1965) has led to general acceptance of the hypothesis that permeability damage in water-sensitive formations is caused by migration of finely dispersed minerals and bridging in "brush heap" arrangements at pore constructions. In laboratory studies, Monaghan et al.' found the use of chemicals to be of only minor value for repairing formation damage. Atwood? however, was successful in substantially repairing damage in a number of low-permeability cores using an n-hexanol flush. In the field, except for treatments with acids, the use of chemical washes to reduce wellbore damage has had limited and sporadic success and generally is unpredictable. A statistical analysis of stimulation treatments in silt-blocked wells has shown that physical manipulation of wash materials is more important than chemical composition." The recent work reported on formation damage in water-sensitive sands brings to mind the results of some unpublished exploratory work done in 1954 in connection with drilling fluid studies.' This laboratory work and subsequent field stimulation treatments indicated a beneficial effect of controlled pressure drawdown and the associated production rate on formation clean-up. This paper reports the results of this work and more recent supplemental experiments on the clean-up of water-sensitive sandstones damaged by water or filtrate invasion. PERMEABILITY RECOVERY AFTER DAMAGE BY DRILLING MUD APPARATUS AND TEST SAMPLES A drilling mud circulating system was used to expose cores to simulated wellbore conditions. The mud flow system is the same as that described by Krueger and Voge17 except that no provision was made for scraping

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

By Perry G. Harrison

The first autlientic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is. said to have worked out his process. Jacobil in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeS04 + (NH4)2SO4. Lenz2 described some properties of electrolytically precipitated iron. He used Klein's bath, FeS0, + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By William L. Fink

Nickel is used as an alloying element in several complex commercial aluminum alloys, among which are found some very interesting properties, such as relatively high strength at elevated temperatures, relatively low coefficient of expansion, the absence of permanent growth, ability to take a good polish, and a bright, pleasing as-cast surface. For that reason the aluminum-nickel system was included in the list of binary aluminum systems that are being studied as a preparation for the investigation of more complex commercial alloys. This paper is the fifteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investigations of equilibrium relations in aluminum-base alloys of high purity. The aluminum-nickel equilibrium diagram from 0 to 18 per cent nickel was determined, using the purest material available. Previous Investigations The entire aluminum-nickel system was studied thermally and microscopically by Gwyer.1 At the aluminum end of the system he found the intermetallic compound NiA13. He found a eutectic at 6 per cent nickel with a melting point of 630" C. A slight thermal arrest, which he could not explain, was also noted in alloys from 2.5 per cent to 41.9 per cent nickel at 550" C. Bingham and Haughton,2 in a later investigation of alloys of aluminum with copper and nickel found the eutectic concentration of the binary aluminum-nickel system at about 5.3 per cent nickel. The melting point of the eutectic was about 633" C., or slightly higher than that found by Gwyer. Although the solid solubility of nickel in aluminum could not

Jan 1, 1934

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed'-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,'~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By John A. Dunn

Continued increase in electric power requirements for mining, brought on by higher capacity mining machines and total mechanization, emphasizes the importance of proper power system design and planning. How effective a mine operates to produce quality coal at low cost depends to a great extent on how well its power system is planned and how well it is maintained. To be planned well it must be adequate to serve all the needs of the mine, it should be safe, there should be a margin for expansion, and it should be easily maintained. In planning a power system for mining coal it is helpful to establish a reliable base for estimating loads. Since most mines are served electric power by utility, power bills for similar mine loads are useful in setting up a base for estimates.

Jan 12, 1964

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By J. B. Wagstaff

The raceway in front of the tuyere of the blast furnace has been studied quantitatively and a correlation obtained for the penetrastudiedtion of the blast. Some evidence is presented for the height and width of the raceway which suggests that all the raceways of a ffurnace overlap. The size of the coke in this zone has been measfurnaceoverlap.ured photographically during normal operation and results are given for the various areas. IN an earlier paper,' it was shown that a raceway exists opposite each tuyere of a blast furnace. This raceway is formed by the jet effect of the air emerging from the tuyere and consists essentially of a turbulence in which coke particles are recir-culated at high speed. Its presence was deduced originally from observations on movies taken with a high-speed camera through the tuyeres of various furnaces and was confirmed by experiments made on a model. In the model described,' this raceway was shown as operating in a vertical plane only, although there was a suggestion in the motion-picture film exhibited at that time that the raceway was three dimensional, unless artificially restricted. There was also some doubt then about the factors influencing its size. This paper describes the next steps in the investigation. Since the size of the raceway is obviously of importance in the operation of the furnace, it seemed worth while to study the subject more carefully. It is probably in this region that about half the coke in the furnace is consumed, so that the movement of the stock column may well be controlled by raceway behavior. Furthermore, there is some evidence to suggest that the coke is packed densely in the center of the furnace to form the "dead man" and more loosely above the raceway. It is therefore probable that the bulk of the gases passing up the stack flow from the top surface of this raceway. Clearly then, a knowledge of this critical zone is of interest to the blast furnace operator, and the first half of this report is devoted to a quantitative discussion of the subject. A further topic of interest among operators is the degree of breakdown of coke in the furnace, with which is inseparably linked the importance of a strong coke. Indeed, the whole question of the optimum size and type of coke may be as dependent on the condition of the coke in the bottom of the blast furnace as at the top. Attempts have been made from time to time to obtain samples of coke from the tuyeres and other furnace openings but they all suffer from the fact that the coke is filled to a varying degree with metal and slag and is probably broken up by the very act of taking the sample. It has proved difficult to make any reliable studies of coke size by these methods. However, it did seem possible to use the highspeed movies mentioned earlier1 to estimate the size of the coke. These movies provide an accurate record of individual coke particles so that, in theory at least, it should be possible to measure the size of the particles one by one and to obtain, for the first time, information on the coke being blown around the raceway under actual operating conditions while the furnace is performing normally. Such a study has been made and is discussed in the second half of this paper. The results obtained enabled the blast furnace data to be correlated with the model results given in the first half. Raceway Size In order to make a quantitative study of the size of the raceway it was necessary to devise some apparatus of laboratory scale, which could be handled quickly and easily. This focused attention on models, which in turn means that the laws of similarity governing this particular process must be ascertained. Method of Procedure: Since the work was to be carried out on a smaller scale than the blast furnace, the linear dimensions of the model became unimportant provided that the scale was known; it is only important to insure that the container does not affect the raceway being observed. The studies therefore were carried out in a glass-sided box, 11 in. high x 7 in. wide x 3 in. deep, using air jets ranging

Jan 1, 1954