Search Documents

By I. R. Kramer, L. J. Demer

T. H. Alden and R. L. Fleischer (General Electric Research Laboratory)— The authors' results indicate clearly and, we believe, significantly that during tensile deformation the surface layers of an aluminum crystal are hardened more severely than the interior of the crystal. A probable explanation of this effect, as the authors indicate, is that dislocations in the primary slip system may be obstructed at the surface or, it should be added, near the surface. The intent of this discussion is to show that the oxide film on aluminum is not likely to be responsible for this effect, but that the results can be understood if it is assumed the secondary slip is more active in the surface layers than in the interior. Prior study has shown that the principal mechanical effect of an oxide film on a single crystal is to raise the yield stress while leaving the rate of strain hardening during the initial deformation relatively unaffected.33 Since the yield stress is unchanged during polishing in the present case, we conclude that continual removal of the oxide film exerts a small effect on the plastic hardening.* It appears that the hardening interactions are occurring not only at the immediate surface, but to an appreciable depth below it, although with decreasing severity. For example, Kramer and Demer found that with removal of 0.004 in. from a specimen, the easy glide region was extended somewhat; but the yield stress did not decrease. The initial yield stress was recovered only after 0.041 in. was removed. Since a very brief polish would permit dislocations trapped behind a surface film to run out,34 extra dislocations must, instead, be trapped to a considerable depth below the surface. The same conclusion is drawn from the observation of decreasing hardening slope with increasing surface removal rates. If the hardening interactions were only at the immediate surface, a full softening effect would be observed at some small removal rate. The view is taken here that strain hardening is principally caused by small amounts of secondary slip.35 The secondary dislocations will interact in various ways with the primaries, interfering with their motion and causing them to accumulate in the crystal. Prior studies of easy glide have shown Diehl's model of hardening to be qualitatively consistent with the effects of impurities,36 of temperature,36 and of crystal size.37 On this basis the enhanced hardening of the surface layers in aluminum arises from increased secondary slip at and to some depth below the surface. Selective removal of this hardened layer is expected to decrease the measurable "bulk" hardening, the effect increasing with the removal rate and decreasing with the applied strain rate. We suggest that the stress on secondary systems is raised by the bending moments arising from interactions with the grips during the deformation. This stress from the grips has been shown to be a maximum37 near the surface, and hence, increased secondary slip should result. Prior investigations of grip effect:; indicate that as the grip stresses are raised by changing the crystal shape, the easy glide slope increases while the extent of easy glide decreases.38-40 It has been shown also that bending moments superimposed during tensile testing may either decrease easy glide, when supporting the moments caused by gripping, or increase it, when cancelling the gripping moments.38 This interpretation of the authors' results, emphasizing the special importance of secondary slip near the surface, is also consistent with the earlier results of Rosi.41 Copper crystals alloyed with silver in the surface layer show greatly increased easy glide compared with pure copper. In addition, the easy glide slope is reduced. The effect of bulk alloying in extending easy glide has been well established and has been interpreted as indicating the relative difficulty of secondary slip in alloy crystals. Since non-basal glide is difficult in zinc crystals, the effects of surface removal during deformation may be less important. Experiments to test this idea are in progress. I. R. Kramer and L. J. Demer (authors' reply)—The authors wish to thank Dr. Alden and Dr. Fleischer for their discussion. Our interpretation of the data in the paper is that dislocation motion is obstructed by "debris" which starts to form at the surface and extends towards the interior of the crystal with further plastic deformation. The fact that we did not find a reversion from Stage II to Stage I by surface removal shows that in Stage II the "debris" fills the entire cross-section of the specimen. Drs. Alden and Fleischer take the view that bending stresses due to the grips are responsible for the

Jan 1, 1962

By T. N. Singh, B. Singh

SUMMARY. The supports account for over 501 of the total expenditure for a longwall face. The success and economics of a face depend upon the optimum selection of type and density of the supports. Empirical solutions involving uncertain safety factor are replaced by a geo-mining approach developed at OMRS in which the support resistance is defined by the stability index of the roof rock mass and the failure pattern of the immediate roof. The paper gives the methodology adopted to define the support resistance for Alkusha colliery longwall face of Jharia coalfield (India). The stability index of the roof mass varied from 218 to 520 for the individual beds and 1100 to 1374 for the immediate roof mass. The exact support resistance for the condition was found to be 42 t/m2.

Jan 1, 1982

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By J. R. Lucas, H. E. Rutherford

The primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this study was to determine experimentally the elastic wnstants of various rock specimens with the use of ultrasonic equipment. Elastic constants can definitely be determined quickly and accurately by ultrasonic investigation. With proper equipment there are indications that ultrasonic waves could be utilized in the detection of flaws, such as fractures and planes of weakness, measurement of thickness, and the study of structure of rock material. Ultrasonic principles have been applied in many industries for the purpose of determining the structural characteristics of various materials. The principal applications of interest here are detecting flaws, measuring thicknesses, and determining elastic constants. The main advantage of ultrasonic analysis is that it is nondestructive. It also has extreme sensitivity, high penetrability, good accuracy, rapid response, and the necessity to have access to only one side of the specimen. These various applications and advantages lead one to think that ultrasonic principles might be applied to rock material in situ for purposes of analyzing its structural characteristics. Therefore, the primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this research was to determine experimentally the elastic constants of various rock specimens with the use of ultrasonic equipment. The term ultrasonics is given to that branch of acoustics dealing with periodic sounds whose fre- quencies are above the audible range or above approximately 15,.000 to 20,000 cps. The first practical production of this high frequency sound was made possible after World War I due to developments of electronically controlled sound wave sources. At the present, the maximum practically attainable ultrasonic frequency is approximately 1000 megacycles per sec. Sound waves of sufficiently high frequency can be made to travel in a beam with little spreading. Therefore, such a beam can explore a material and detect nonhomogeneities in it by reflection. This is the principle of the ultrasonic reflectoscope invented by F. A. Firestone' in 1942. An ultrasonic beam, on pulse-penetratink a solid material medium, produces an echo when it strikes a flaw which has different acoustical properties than the surrounding medium. This echo can be detected by the same transducer which sends out the original pulse. This principle is the basis of the important industrial techniques of nondestructive ultrasonic testing of metals and other solid material. Later developments in the field of ultrasonic testing of solid material have been mostly improvements in equipment and instrumentation. To date, most of the industrial applications of ultrasonic analysis of solid bodies have been in the aircraft, electrical, and nuclear energy fields on the nondestructive testing of metal. The one solid material similar somewhat to rock material, upon which some work has been done to apply ultrasonic testing techniques to study structural integrity, is concrete. Jones and Gatfield3 briefly summarize this work on concrete. Their basic conclusion was that the strength of concrete was a function of the change of the longitudinal sound wave velocity in the concrete. Only recently has any extensive study been made to apply ultrasonic testing techniques to rock material. Lutsch studied rock material by an ultrasonic pulse method to determine the extent and degree of fracture of rock faces. Lutsch states that the number of observed reflections is a measure of the degree of fracture and that only ultrasonic waves are able to detect fractured zones subjected to high pressure. Suzuki, Sasaki, and Siohara5 studied the characteristics of the sonic wave in rock for propagation over a wide range of wave lengths. They indicated that, in rock, the propagation constant and attenuation of the

Jan 1, 1962

By S. Skowronski

OvErpolEd copper, as commonly defined,- is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such coppcr is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in 'crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, which enablcs copper to be cast free from blowholes. It seems that when oxygen is present, other gases are less soluble in molten copper; when oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, while an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen,' and the effect of this action on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulfur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 1, 1919

By W. Francis

Before attempting to describe the application of recently acquired knowledge to the classification of coal it will be as well to consider the objects at which a scientific classification should aim. Here one can not do better than to follow the example of Clarence Seyler,l by quoting from Huxley's "Classification of Animals:" "By the classification of any series of objects is meant the actual or ideal arrangement together of those which are like and the separation of those which are unlike, the purpose of the arrangement being to facilitate the operation of the mind in clearly conceiving and retaining in the memory the characters of the object in question. Thus there are as many classifications of any series of natural or other bodies as they have properties or relations to one another or to other things. But the statement of the characters of the class ... is something more than an arbitrary definition ... it expresses firstly, a generalization based on and constantly verified by very with experience; and, secondly, a belief arising out of that generalization—in other worda. the definition of the class is a statement of a law of correlation or coexistence . . . from which the most important conclusions are deducible." In that same sense writes John Stuart Mill, in the chapter on classification in his "Logic:" "The ends of scientific classification are best answered when the objects are formed into groups concerning which a greater number of general propositions can be made, and these properties more important, than could be made respectiug any other groups into which the same things could be distributed. The properties, therefore, according to which objects arc classified should, if possible, be those which are causes of many other properties, or, at any rate, which are sure marks of them." Now in the case of coal, the properties which have been used from time to time for classification purposes are the ultimate analysis, volatile matter, caking power, calorific power, burning properties, etc. Seyler has shown that there is a general law of correlation or coexistence between the ultimate composition and the other properties. The ultimate composition, therefore, of the natural series of bodies known as coal is the

Jan 1, 1930

By C. H. Herty

AN earlier paper on absorption of sulfur by the slag in the basic open-hearth furnace included a brief discussion of the absorption of sulfur during the melting period. The data available at that time showed that the amount of sulfur absorbed by the melting scrap was proportional to the sulfur content of the furnace gases, and the following statement was made: "The conclusion may be drawn from these results that if a gas entirely free from sulfur were used during the melting, any iron in direct contact with the gases would be completely, or nearly completely, desulfurized before it reached the bath proper." The experimental work discussed herein deals with absorption of sulfur by the melting scrap when fuels with both high and low-sulfur content were used. Before taking up the experimental work let us consider the process as a whole as to the "flow" of sulfur. The input of sulfur occurs in: 1, the hot metal charged; 2, the scrap; 3, the stone or lime charged; 4, the ores charged; and 5, the gas. Sulfur goes out of the furnace in the steel, the slag and the gas. The distribution of sulfur in the furnace depends on the sulfur concentration in each of these materials and on the equilibrium conditions between them.

Jan 1, 1926

By John H. Hollomon

IN recent papers, O'Neill,1 Vivian,2 and Zener and Hollomon3 have reviewed some of the information concerning the relations between stress and strain during plastic deformation. Since further information has been obtained since these reviews were published, this paper attempts to further coordinate and amplify the knowledge concerning the plastic deformation of metals in simple tension. Ordinarily the results of tensile tests of metals are presented as graphs in which the load divided by the original area is plotted as a function of the percentage of elongation measured over some specified gauge length. The interpretation of graphs of this sort is limited, since the stress required to deform the metal at any stage of the deformation is actually the load divided by the instantaneous rather than the original area. Furthermore, each increment of the deformation is performed on metal that has been previously deformed, and, as pointed out by Ludwik,4 the strain could be more effectively defined: [e = In A t][I] where a is the strain and Ao and A are, respectively, the original and instantaneous areas. The results of the tensile tests can be more effectively presented and interpreted if the stress* (load divided by actual area) is plotted as a function of the strain as defined above. A schematic curve of this type is presented as Fig. I. In a previous paper,6 the concept of Ludwik7 concerning the flow and fracture of metals was successfully employed to explain some of the puzzling results of notched-bar impact tests of steel. It appears that the use of this concept is very fruitful and should be kept in mind in any study of the deformation characteristics of metals. Ludwik considered that a flow stress-strain curve of a metal was essentially a locus of points that described the stress required for plastic flow of an infinite number of specimens, each with a different strain history determined by the preceding part of the flow curve. Each of these specimens can also be considered to have a fracture strength. Unfortunately (or fortunately depending upon the point of view), all the specimens, except the one deformed to the fracture strain, flow and do not fracture. Even though the metals do not fracture, the concept of a fracture-strength curve seems

Jan 1, 1945

By O. Vartiainen, R. T. Hukki

A preliminary investigation of the collecting effects of various fatty acids in tall oil has led to a conclusion that the collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain, Linoleic acid was found to be an excellent collector for oxide minerals.

Jan 8, 1953

By James K. Stanley

PREFERRED orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.1 In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurgical literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanical properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important in- formation, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational under- standing of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing 'stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required-it is only necessary punch or machine a disk of the sheet material and insert it into the testing device.

Jan 1, 1943

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By W. H. Adams

Among the persistent experimenters of the present century no one man is more widely and favorably known in the metallurgical world than the late Peter Spence of Manchester, England, to whom we are indebted for many of the successful processes in the manufac ture of acids and alkalies, and for much of that perfection in me chanical detail which goes so far towards insuring success. For the past twenty-five years—a period covering the greatest changes in soda-processes and a revolution in acid-manufactures ef fected by the substitution of pyrites for brimstone—Mr. Spence was constantly engaged in perfecting the plant for the economical treat ment of pyritous ores; and no text-book has been complete without reference to his many inventions, patented or otherwise. The results of his labors for the past six years were not given to the public, by reason of the active competition existing among man ufacturers on the continent of Europe and in Great Britain ; but it was well known and conceded that the crowning triumph of his .life had been achieved in the successful working of his automatic desulphurizing furnace, which mechanically calcined "smalls" or finely crushed pyrites—the bugbear of all chemical manufacturers. That he was met by many delays and disappointments, and that

Jan 1, 1885

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By O. R. Wagner, R. O. Leach, H. W. Wood, C. F. Harpke

PAN AMERICAN PETROLEUM CORP.TULSA, OKLA. CASPER, WYO A field test has been made in which additional oil recovery was obtained from a previously-waterflooded "oil-wet" sandstone reservoir. This recovery improvement was accomplished by adjusting the reservoir wettability through chemical treatment of the flood water. The test was made in the Muddy sand of the West Harrisburg Unit, Neb. The chemical used, sodium hydroxide, was injected as a slug of dilute caustic solution through a water-injection well. The natural wettability of the reservoir and the chemical requirements for reversing wettability were determined in the laboratory from contact-angle studies using field water and oil samples. Laboratory flood tests with a synthetic system had shown that reversing the wettability of an oil-wet consolidated core would lead to improved oil recovery. The field performance indicates that the mechanism by which increased oil retovery is obtained in the field is the same as that observed in the lahoratory. Laboratory studies indicate that higher ultimate recoveries and decreascd water-injection requirements result when the adjusting agent is added early in the life of the flood. However, a previously waterflooded area was intentiorzally chosen for the field test so that unambiguous conclusions could be made about the effects of chemical injection on wettability and the extent of oil-recovery improvernent afforded by wettability reversal. Forces existing at the fluid-solid and fluid-fluid interfaces in a porous medium have an important effect on oil recovery during a water flood. Modifying these interfacial forces in the reservoir to improve oil recovery has been the object of much research. Several papers' ' have discussed the use of surfactants to lower the water-oil interfacial tension. This paper describes work concerned with improving oil recovery by modifying the forces at the fluid-solid interfaces— that is, by changing the preferential wettability. An earlier paper: presented evidence to show that some reservoir systems could be changed from preferentially oil-wet to preferentially water-wet by the action of simple chemicals added to the water to increase waterflood oil recovery. The process was attractive for further study because it used only inexpensive chemicals and because it called for a gross "wettability reversal" rather than for a precise adjustment. The present paper is an extension of the earlier work. Laboratory flow tests were made using treated water and oil in a consolidated core to determine the amount of additional oil recovery and the producing performance which might be expected from reversing the wettability of an oil-wet reservoir during a flood. A contact-anglc study using water and oil from the Muddy "J" sand of the Harrisburg field, Banner County, Neb., indicated the reservoir to be preferentially oil-wet and susceptible to wettability reversal through chemical injection. Based on these studies, a field trial of wettability-reversal water flooding was initiated. in the Harrisburg field. The primary purpose of the trial was to determine if wettability-reversal flooding would improve oil recovery in an actual field situation. The field trial was also an important test of the laboratory tecnique used to determine the effect on oil recovery of certain wettability manipulation, as well as a test of the contract-angle method of determining reservoir wetra-bility. The paper is presented in two parts. The first part covers the laboratory experiments leading up to the field trial, and the second part covers the field trial. PART I—LABORATORY STUDY The laboratory experiments consisted of displacement tests using an idealized fluid system and of a contact-angle study with crude and water from the Muddy "J" sand of the West Harrisburg Unit, Banner County, Neb. The displacement tests were designed to determine the effects of a particular wettability manipulation, oil-wet to water-wet, on oil displacement in a water flood. The contact-angle measurements were made to determine the natural wettability of the reservoir and to determine if beneficial wetting changes could be brought about by a chemical addition to the flood water. PROCEDURE DISPLACEMENT TESTS The displacement tests were perfornled in a consolidated sandstone core using a refined oil and water. The wetting properties of this system could