Search Documents

By C. R. Hocott

The distribution and movement of fluids in oil reservoirs are influenced to a great extent by capillary forces, which depend upon the size and shape of the pores in the reservoir rock, the surface characteristics of the rock, and the interfacial tension between the fluid phases. This paper presents the results of an investigation of the interfacial tension between salt water and crude oil containing dissolved gas under reservoir conditions. Apparatus and Procedure In the preliminary phases of this investigation, it was found that a scum formed at the oil-water interface, which made measurement of interfacial tension by either the ring or capillary rise methods unreliable. Accordingly, the drop-weight method, in which a fresh interface is continuously formed, was selected. In this method, a tip through which drops of one fluid can be expelled is immersed in a second fluid. At the instant that the drop becomes large enough to fall, the gravitational force tending to pull away the drop exactly balances the interfacial force tending to hold it. From the size of the drop, the dimensions of the tip, and the density of the two fluid phases, the interfacial tension may be calculated. The apparatus consists of a circulating pump for bringing the oil to equilibrium with gas at the desired pressure, a displacement pump for forming the drops, an interfacial tension cell in which the drops are formed, and a density cell to determine the density of the oil. The density of the water is determined separately in another apparatus. A flow diagram of the assembled equipment is shown in Fig. 1. The interfacial tension cell contains a stainless-steel dropping tip suspended from the top and extending below the surface of the oil. The tip is a cylindrical rod with a small hole in the center through which the water was forced to form the drop on the lower face. The walls of the tip were highly polished, to prevent the water on the tip from creeping up the side and increasing the effective diameter. The face of the tip, how-

Jan 1, 1939

By H. O. Hofman, H. L. Norton

Zinc smelters in the central western States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 per cent. of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-carboniferous limestone, and is associated with chert, residual clay, cal-cite, pyrite or marcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1; marcasite, from 4.85 to 4.90; and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores' is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, side-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

By E. E. Malouf

With the continued development of low-grade porphyry copper deposits by open pit mining, substantial amounts of copper-bearing strip material have been accumulated in waste dumps adjacent to the many large mines. Since the end of World War II, the production of copper from leaching these copper-bearing wastes increased from approximately 4% of the total copper production to 10% by the early 1960's. Projected increases will probably raise this figure to 20 to 30% by the early 1970's. Furthermore, a gradual recognition of the economic feasibility of leaching mined-out areas is evident and will undoubtedly contribute additional production. Waste dumps in canyons and gulches on the periphery of open pit mines, mine stopes, caved areas, and abandoned open pits often contain substantial quantities of leachable rock ranging in concentration from 0.1 to 0.4% copper. Recent developments in the leaching of copper, mainly the recognition of bacterial oxidation of sulfide minerals combined with better under- standing of the control of the salt content of the leach solutions, both by adjusting the pH and/or by hydrolysis, are resulting in a greatly expanded recovery of copper from these hitherto uneconomic mine rejects. 11.5-1. Mechanism of Leaching. Leaching processes for the extraction of metal values from mine ore or waste may be classified for convenience as either chemical leaching or bacterial leaching. Chemical leaching is considered to be the extraction of soluble salts by metathesis in acidic, basic, or neutral water solutions. The reactions involved may be evaluated by chemical thermodynamics. Bacterial leaching, although a chemical process, is dependent on biological catalysis and this is generally a much more complex process. This justifies its separate treatment in the application to leaching. Acid ferric sulfate solutions are commonly employed in the mining industry to leach valuable metals from metal sulfide ores. The leaching mechanism is a reduction-oxidation reaction in which minerals are oxidized at the expense of ferric sulfate. Such chemical leaching is profitable when

Jan 1, 1968

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By R. H. Merrill, D. W. Wisecarver

The paper "Design of Surface and Near-Surface Construction in Rock" by Deere, Hendron, Jr., Patton, and Cording discloses a principal difference between civil and mining engineering as applied to openings in rock. Generally, the civil engineer considers an opening as an asset, where a mining engineer finds that most of his openings are a liability. The openings, or rock surfaces, treated in the paper by Deere and coauthors are designed for lasting stability and the foundations for dams, the diversion tunnels, abutments, and surface excavations are expected to be stable for long periods or provide continuous access and other useful purposes. Except for those openings used for the transportation of men, materials, ore, and for ventilation, the mining engineer finds that his underground openings serve no useful purpose once the mineralized rock has been removed. Usually, these openings create problems such as reduced ventilation efficiency, added requirements for scaling, sealing, and other tasks necessary to maintain or isolate the openings. The surface openings and mine plants present another liability to the mining engineer. After the product has been removed from the earth, the abandoned pits or strips, tailing ponds, dumps, and buildings sometimes become hazardous, unsightly, or occupy surface areas that could be used for other purposes. As a general rule, the various disciplines involved in rock mechanics have different objectives and uses for openings; however, the basic concepts regarding the design or control of openings in rock are similar for each discipline. The review by Deere and his coauthors contains examples of the duplications in this technology, and, in particular, the common approaches used by civil and mining engineers. Therefore, both the review paper and this report consider the problems that are common to most of

Jan 1, 1967

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By P. K. Chatterjee

The overall success of many strip coal mining operations depends primarily upon the efficient use of draglines to remove overburden. These machines require enormous capital investment and unless used efficiently the profitability of a venture is adversely affected. It is important that the dragline works continuously and it is imperative that the walking path and other facets of its operation be predetermined exactly so that the desired production rate is achieved with a minimum of non-productive time. Details of dragline operations which are of particular interest are walking path, prediction of best cut and positioning to maximize production, the angle of swing which produces the swiftest operation, optimum fill factor allowable for the type of material and conditions of ground, the maximum depth from which it can excavate and operating level with respect to the elevation of the high wall. The aims of the present paper are: 1. To establish a cut-off point in the cost-depth ratio. 2. Predict the most economic method of stripping in a given area using graphical plots of walking path implemented with information necessary to ensure optimum production. The optimum operating efficiency of the dragline in relation to the terrain and other conditions imposed on its operation will be evaluated. The model is based upon operating data which has been collected from site observations of a large strip coal mining operation in Central Queensland, Australia.

Jan 1, 1977

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By L. Larson

SMELTERMEN in the copper industry know that punching the tuyeres of a copper converter is a difficult, disagreeable, and at times a hazardous job. Knowing this, many men in the industry have given serious consideration to punching by mechanical means. As evidence of such consideration, a great many patents have been issued covering various mechanical devices or machines for doing this task. In 1942, as war-created manpower shortages became more acute, it became increasingly difficult to get men to punch tuyeres. Faced with this situation at the McGill smelter, it was decided that an all-out effort should be made to develop some sort of a mechanical punching device. The various patents were studied over thoroughly but none of the devices seemed suitable, all were discarded and it was decided to develop one, using the ideas of the personnel at McGill. Initial test work indicated that a separate punching device should be attached to each tuyere. This meant that an adapter would have to be developed which would accommodate such a device; the adapter to be so constructed that it could be substituted for the regular Dyblie valve head, and be punched either by mechanical means or by hand. Also a method for quickly attaching or detaching the punching unit would have to be devised. If the punching unit was attached to the adapter, then the punch rod and tip would have to remain inside of and reciprocate within the tuyere pipe. This last requirement meant that the punching device, the adapter, the piston rod, and punch rod must be in perfect alignment. The whole arrangement thus would become an integral part of the converter and would rotate along with the tuyere line to all the positions required for converter operation. If the puncher was to rotate with the converter, there was also a problem of limited clearance. The construction of a device to meet all of these conditions imposed many problems. In the latter part of 1942, two pieces of equipment were constructed and tried out under test-stand conditions. Both of these devices were very crude, but test-stand operation indicated that progress was being made. Neither of the units was considered good enough to be attached to and tried out on a tuyere of an operating converter. In May 1943, work was started on another device and in August of that year it was attached to and actually punched a single tuyere of a converter on an experimental basis (fig. 1). This unit was essentially a cylinder 3 in. in diam and about 15 in. long inside. Valve ports were so located as to provide a 1-in. cushion on each end of the stroke. The cylinder ports were piped to a 3/4-in. four-way disk valve. High pressure air (90 psi) was delivered to the valve by means of a long hose, thus making it possible to supply air to the device at all operating positions of the converter. The forward and return punching strokes were accomplished by shifting the valve handle as required. With the 3/4-in. valve, stroke velocities from 15 to 18 fps were achieved. Punching with this experimental arrangement was carried on for some time, but many difficulties were encountered. The punch rod tips often stuck in the tuyere accretion, indicating that more energy of some sort was necessary to avoid sticking the punch rod. To overcome sticking, experiments continued with a speeded up unit and although progress was made, troubles of various kinds continued to appear. On this unit, piston cup seals passed the valve ports which proved to be of very poor construction. Also the piston, driven forward at approximately 28 fps, would often bottom metal to metal in the forward end of the cylinder causing both mechanical and operational trouble. Sometimes the punch rod and at other times the piston rod would break loose and be shot through the tuyere pipe into the converter. Bottoming and poor timing of valve reversal caused a bounce and a hesitation at the end of the forward stroke, with the result that the punch rod

Jan 1, 1951

Dimitri Konstantinovitch Tschernoff, was horn in Petrograd, Russia, on Nov. 1, 1839, and died in Yalta (Crimea) in the south of Russia, on Jan. 2, 1921. He obtained his early education in the Russian Gymnasium, corresponding to the American high school, and in the Technologic Institute. On graduation from this Institute in 1858, he was engaged as a professor of geometry and algebra and later became a librarian and superintendent of the museum in the same Institute. He also attended lectures in the mathematical physics section at the Univrrsity of Petrograd from 1859 to 1862. In 1866, Professor Tschernoff left the Technologic Institute and entered the employ of the Obouchoff steel plant, founded in 1863 for the manufacture of guns. Here he did his most important work on the heat treatment of steel, its crystallization and metallography. In 1880, he left the Obouchoff plant and went to the south of European Russia, where he discovered and developed some rock-salt mines. This enterprise brought him a rather large fortune. In 1884, he returned to Petrograd and during the next four years held several prominent positions in government departments. In 1899, he became professor of metallurgy in the Michael Artillery Academy, and retained that position until the time of the Russian Revolution. In 1902, Professor Tschernoff was elected an honorary member of the American Institute of Mining and Metallurgical Engineers. In September, 1917, Professor Tschernoff was sponding his vacation, as usual, in the city of Yalta (Crimea) in the south of Russia, with his wife and one of his daughters. The revolution progressed so rapidly that they were unable to return to Petrograd, and were compelled to stay in Yalta without provision for the winter season. Suffering from hunger. and lack of sufficient clothing, and deprived of his books, Tschernoff nevertheless continued his studies and gave a number of lectures on steel at the Polytechnic Institute. At the same time he worked hard on some. mathematical problems. His health broke down through long-continued under-nourishment. His works in the metallurgical field are well known to the students of metallurgy; good abstracts of his most important papers were published in Revue de Metallurgie (1915, pp. 829-882) in commemoration of his 75th birthday.

Jan 1, 1922

By J. W. Harden

AT our meeting in October last we saw in operation at Pittsburgh, the comparatively modern process of the utilization of small coal by washing, by an arrangement similar to that of Berard or Morrison. The small coal washed was that of an old pile, the refuse of the mining of the Pittsburgh bed, and which had long lain uncared for. Value was thereby restored to it when it was converted into a very good coke. This circumstance led to comments on the mountains of broken coal lying wasted, and in its present condition worse than useless, in the neighborhood of the mines of the Wyoming Valley, though they are not confined to that district. Some things were said condemning the course which produced it, some were left unsaid. Of a system that destroys one-half the coal-bed in producing the other half there can, however, be but one opinion. Schemes have been suggested for the utilization of present accumulations which, if successfully applied, would in so Far be beneficial. More than ordinary attention is now being given to the same subject in England ; a Mr. Barker has invented a means by which he amalgamates the "dust," too fine to burn in ordinary grates, with a composition he calls "diamond cement," producing blocks of coal said to resist water, both hot and cold, and which a smart blow will only break to pieces, not cause to crumble. But any scheme less than the one which will prevent the wasting of coal, which still goes on, though that involves the aban- donment of the breaker, will only be one of expediency; and the latter can only be done by the aid of the consumer. But the wasting of coal is not alone with the breaker; much is made in the mine. The cause is not far to seek ; the remedy is with capitalist and owner. Owners and consumers then are alike interested, and they have it in their power, in the one case, to mitigate, in the other, almost entirely to remove the cause of the evil. Of consumers there is one in every

Dimitri Konstantinovitch Tschernoff, was horn in Petrograd, Russia, on Nov. 1, 1839, and died in Yalta (Crimea) in the south of Russia, on Jan. 2, 1921. He obtained his early education in the Russian Gymnasium, corresponding to the American high school, and in the Technologic Institute. On graduation from this Institute in 1858, he was engaged as a professor of geometry and algebra and later became a librarian and superintendent of the museum in the same Institute. He also attended lectures in the mathematical physics section at the Univrrsity of Petrograd from 1859 to 1862. In 1866, Professor Tschernoff left the Technologic Institute and entered the employ of the Obouchoff steel plant, founded in 1863 for the manufacture of guns. Here he did his most important work on the heat treatment of steel, its crystallization and metallography. In 1880, he left the Obouchoff plant and went to the south of European Russia, where he discovered and developed some rock-salt mines. This enterprise brought him a rather large fortune. In 1884, he returned to Petrograd and during the next four years held several prominent positions in government departments. In 1899, he became professor of metallurgy in the Michael Artillery Academy, and retained that position until the time of the Russian Revolution. In 1902, Professor Tschernoff was elected an honorary member of the American Institute of Mining and Metallurgical Engineers. In September, 1917, Professor Tschernoff was sponding his vacation, as usual, in the city of Yalta (Crimea) in the south of Russia, with his wife and one of his daughters. The revolution progressed so rapidly that they were unable to return to Petrograd, and were compelled to stay in Yalta without provision for the winter season. Suffering from hunger. and lack of sufficient clothing, and deprived of his books, Tschernoff nevertheless continued his studies and gave a number of lectures on steel at the Polytechnic Institute. At the same time he worked hard on some. mathematical problems. His health broke down through long-continued under-nourishment. His works in the metallurgical field are well known to the students of metallurgy; good abstracts of his most important papers were published in Revue de Metallurgie (1915, pp. 829-882) in commemoration of his 75th birthday.

Jan 1, 1922

The Board of Directors on April 18, 1940, adopted a resolution providing that "no person who has been awarded any one of the four medals-Douglas, Saunders, Lucas, and Rand-is eligible for consideration for any other of the four medals " Later in the year the rules for the award of these four medals were revised and, so far as practicable, made uniform The medalists are elected by the Board of Directors, on recommendation of special standing committees of award, appointees on which serve four-year terms and are engaged in the branch of industry represented by the respective awards Under the rules only members of the committees of award are eligible to propose candidates\ for the nomination

Jan 1, 1952

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By Frederick Forscher

Frederick Forscher (Nuclear Materials and Equipment Gorp.)—It is gratifying to see another series of experimental results that essentially reconfirms our reported observations of "Strain-Induced Hydrogen Embrittlement in Zirconium" (F. Forscher: AIME Trans., 1956, vol. 206, p. 536, noted as Ref. 3 of paper). However, several important considerations may have been overlooked, or—at least—have not been specifically pointed out. It is the purpose of this discussion to present some of these considerations. The statement is made that "the equilibrium concentration of hydrogen in solution at 20°C in zirconium is approximately 10 ppm; i.e., no zirconium hydride precipitates are formed at or below this hydrogen content." This is perhaps the case in the unstressed condition. In the presence of triaxial (plastic) strain however, even as little as 1.4 ppm H2 (Forscher's Figs. 6 and 11) will cause porosity near fracture in 20°C tests. The necked-down region that develops during a tensile test provides the triaxiality necessary for these pores to open. Both Beevers' and Forscher's micrographs show that porosity is concentrated in the necked region. So-called "pure zirconium" containing about 10 ppm H2 also shows pronounced porosity near fracture (Beevers' Fig. 3). Since it is generally agreed that such porosity is

Jan 1, 1965

By M. L. Fuller

The fundamental mechanism of the deformation of zinc has been thoroughly described by several prominent investigators, particularly Mark, Polanyi, and Schmid,1 Mathewson and Phillips,2 and Schmid and Wassermann.3 The deformation of zinc occurs primarily through slip along basal planes (00.11, and secondarily through twinning on pyramidal planes of the form (10.2). In addition to these basic studies on single crystals, there have been a number of determinations4,5 of preferred orientations developed in rolled, polycrystalline zinc. In no case, to our knowledge, has there been described the development of oriented structures in zinc as a result of a systematic series of rolling treatments. The work included in the present paper shows the changes in orientation produced in a zinc alloy by successively increasing degrees of cold-rolling reduction. This alloy has the same crystal form, hexagonal close-packed, as zinc, but its susceptibility to hardening for a given degree of working is much greater because of its higher recrystal-lization temperature. Experimental Procedure Composition of the Alloy and Rolling Treatment The alloy used in this investigation consisted of zinc of 99.9 per cent purity to which 1 per cent of copper and 0.01 per cent of magnesium had been added.

Jan 1, 1934

By H. Ries

SPECIAL sands are those that are employed for special purposes. They have a limited use, as compared with sands for concrete and plaster. The sands discussed in this chapter are those used for foundry purposes, glass manufacture, filter beds, abrasive purposes, sandblasting, engine sand, sand for sheet asphalt, and furnace sand. These sands are almost invariably high in silica, consisting chiefly of quartz grains. In some-for instance, glass sands-freedom from ingredients other than silica, such as iron oxide, is important. Certain grades, like filter sand, require rather careful sizing, and in foundry sands the bond, usually clay, is important. One deposit may sometimes be used to supply several grades or types of sand by appropriate methods of screening and washing. The special sands discussed here are usually obtained from deposits of unconsolidated material but sands high in silica are derived occasionally from soft sand- stones that can be disintegrated easily. Requirements are not the same for all uses, and, while certain properties may be demanded, there are no officially adopted standard tests except for foundry sands. FOUNDRY SANDS Definition-Foundry sands include those siliceous sands that are used to make the forms for casting metals. If these are employed for making molds, they are known as molding sands; if for the cores that form the hollow spaces in the casting, they are called core sands. Naturally bonded sands are those containing a variable, though not usually large, amount of clay, which serves as a bond. Synthetic sands, now much used, represent an artificial mixture of sand with usually fire clay or bentonite. Core sands may be bonded with oil, cereal binders, resin, pitch, or other materials. The foundrymen apply the term "sharp sand" to one that is free from bond. Properties-The important properties to be tested at room temperature are texture or fineness, permeability, strength, deformation, and flowability. Those tested at elevated temperatures are compressive strength, expansion and contraction, sintering point, and durability. More attention probably has been given to research on the properties

Jan 1, 1949