Search Documents

By James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to loo per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By Herbert D. Drechsler

The objective of this paper is to identify the components of income above that necessary to keep a mine in production and relate those components to the profits of a mining firm. This is a discussion of "Economic Rent". Economic rent is the payment to the factors of production -- capital, labour, entreprenuer and the owner of the mineral deposit -- above the minimum necessary to keep all of these factors cooperating in the production of minerals from a particular deposit. THE SOURCE OF ECONOMIC RENT IN THE MINING INDUSTRY In the mining business each mine has a unique cost of production unrelated to any other mine. The cost of production is developed from many factors such as the technical characteristics of the deposit: depth of deposit, depth of overburden, areal extent, and type of deposit. Furthermore, there are locational factors which also alter cost of production. For example, identical mineral deposits located in Zambia or in the southwest U.S.A. would have different capital and operating costs. These differences occur because of different qualities of labour, ease of acquisition of operating supplies or investment capital and other similar factors. To explain the source of rent, we shall use ideas developed by Alfred Marshall and Kenneth Boulding. Suppose a meteorite with special qualities exploded over earth and sent showers of small meteorites to the ground in various places. At some point in time, people learned of the special qualities of these meteorites and a demand arose and one mine was started. Suppose further that the cost of production to produce these meteorites was different for each deposit. Probably the lowest unit cost mine would commence production because if a higher unit cost mine started-up, eventually someone would discover a deposit that had a lower unit cost of production. The lower unit cost mine would take over the market and the high unit cost mine would cease production. The cost curve for the first mine would look like the following Figure 1. [ ] The output for the first mine is on the horizontal axis with the cost per ton on the vertical axis. The curve labelled AC I is the average total cost of production over the range of possible production that could occur at the property. The total costs are composed of variable costs, which are dependent on output and fixed costs, which are dependent on time. For example, the cost of operating supplies would be a variable cost and normal profit would be a fixed cost.1 The opportunity cost of the investment would also be part of the fixed costs. In our example, all factors of production, are receiving the minimum necessary payment that will keep the mine operating. The average total cost curve is U-shaped because at zero output, the meteorite mine has no variable costs, only fixed costs which, on a unit basis, obviously are very high. To produce a small output of meteorites, the mining firm adds

Jan 1, 1985

By Martin J. Conway

DURING the past year, the intense interest shown by the metallurgical industry in the use of relatively pure oxygen has been evidenced by the number of papers dealing with its application and production. The reason for this interest is apparent when it is realized that, weight for weight, oxygen enters into the formation of steel equally with iron. In the manufacture of steel, approximately one ton of oxygen is required to produce one ton of ingots. Until the recent development of plants capable of producing oxygen at far lower costs than had ever previously been considered possible, the oxygen required for steel manufacture was used as it occurs in air, where it is associated with approximately four times its volume of nitrogen. Because of the diluent nitrogen more than 4 tons of total gaseous material per ton of steel must be handled rather than only approximately one ton required when pure oxygen is used. In addition, provision must be made to handle the large quantity of waste, gases resulting from the process. There are cases where the reduction in gas volume alone can justify the installation of an oxygen plant.

Jan 1, 1947

By R. D. Coleman, A. E. McIlhinney, C. E. Capes

tentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product.1 Fine Coal Treatment Processes Most coal cleaning methods depend upon the density difference between coal and its impurities to effect separation. These gravity concentration methods, however, are not practical for particles finer than about 100 mesh and cleaning methods dependent upon the differences in

Jan 1, 1971

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By D. A. Thomas, E. S. Meieran

Tungsten wires were examined by transmission electron microscopy after drawing and after high-temperature annealing. Drawn wire consists of highly elongated grains called fibers, whose long axis is parallel to [110]. Each fiber is ribbon-shaped, with the wide dimension of the ribbon parallel to (001) and the narrow dimension parallel to (110). Furthermore, most fibers are bent about [I10] and twisted along their length. The fibers are divided into cells, which in some cases contain a platelet substructure lying on (110) planes. The misorien-tations of these platelets accumulate to allow the macroscopic twist of the fibers. During annealing, several competing reactions occur, starting at different temperatures and progressing at different rates. Among these processes are fiber-boz~ndary migration, polygonization, dislocation rearrangement, and possibly impurity segregation. The fiber-boundary migration accompanied by the formation of transverse boundaries during polygonization leads to an equiaxed grain structure although recrystal-lization does not occur. There is a relationship between the flow stress of the wires and their average subgrain width in the form sy = s0 + kyd-1/2 . Also, there appears to be a relatio'nship between wire ductility and the formation of transverse boundaries during annealing at about 800°C. THERE have been many investigations of the structures and properties of tungsten wires1-4 due to their commercial importance for use as lamp filaments. The structural studies have so far been limited to optical microscope and replica electron-microscope studies. due to the difficulty of .-me- paring from wires thin foils which can be examined by transmission electron microscopy. However, this difficulty has been recently overcome,5 and it is now possible to examine tungsten wires by transmission electron microscopy as well as by other techniques. In this paper, the structure of drawn tungsten wire is described, as are the changes in the structure during high-temperature annealing. Some discussion of the relationship between structures and properties is also given. EXPERIMENTAL MATERIALS AND PROCEDURES Commercial 0.030-in.-diam doped tungsten wires drawn at progressively decreasing temperatures between about 1400° and about 800°C were examined. The composition, mechanical properties, and optical microstructures are described in detail elsewhere.' All experimental materials were vacuum-annealed for 10 ot 30 min at temperatures at 100°C intervals between 700° and 2000°C. Specimens were thinned for examination in the Siemens Elmiskop I electron microscope by the method of Meieran and Thomas.5 STRUCTURE OF AS-DRAWN WIRE The optical microstructure of as-drawn tungsten wire has been described by Peck and Thomas.7 They observed that wire in longitudinal section consists of highly elongated grains called fibers whose width varies between 1 and 10 µ, while in transverse section the fibers appear to be elliptical in cross section and bent about their common [110] wire axis. They explained this unusual appearance as being due to the drawing of a bcc material with a [110] texture, and predicted that the wide and narrow planes of the fiber cross section would be parallel to (001) and (110), respectively. The fibers apparently bend about the [110] axis during drawing to maintain grain boundary continuity during drawing. Transmission electron microscopy offers a way of checking these predictions as well as providing a more detailed picture of the wire structure. Figs. 1, 2, and 3 are typical electron micrographs of

Jan 1, 1965

By C. L. Burrill

The forecasts presented in this paper constitute an attempt by the writer to predict the pattern of the consumption of petroleum products in the United States during the period of transition from war to peace. Although, in preparing the estimates, secular trends were not overlooked, greater emphasis was placed upon considerations of a cyclical character, or upon influences which might be peculiar to parts of the period. The estimates do not extend beyond the year 1950 because by then conditions in the industry should have returned to normal. The consumption of petroleum products is affected, of course, by changes in the condition of business in general. Before estimates of petroleum consumption could be prepared, therefore, it was necessary to predict the pattern of general business during the period under review, particularly the economic series that in the past have shown the closest relationships with petroleum consumption. It is the writer's view that business activity in this country (as measured by industrial production) will be higher on the average during the period between the end of the war and the year 1950 than it ever was before during a peacetime period of the same duration. When the war is over, consumers will have saved amounts of money that will be very large as compared with any previous accumulations. There is little question, therefore, as to the financial ability of consumers to purchase goods. The production of many durable consumers' goods, such as automobiles, refrigerators and radios, has been completely stopped since early in the war; also, many semidurable and nondurable consumers' goods have not been available in the quantities or the qualities desired. There is considerable needi therefore, for consumers to purchase goods after the war. The important question is whether consumers will purchase goods in "1arge enough quantities to keep our economy running at a high level. The writer answers this question in the affirmative. The mere existence of very large consumer savings lends considerable support to this view because, with such backlogs of " security," consumers can afford to spend more of their current earnings than they otherwise could. Also, several polls have been taken, which indicate that consumers expect to buy large quantities of a variety of goods. Some of the savings, therefore, probably will go into current consumption. Even though this percentage is relatively small, so that the bulk of the funds accumulated by consumers during the war continues to remain as savings during the period under review, spending should be great enough to start the production cycle and keep it

Jan 1, 1945

By Claude H. P. Lupis, John F. Elliott

The classic Siez~erts' technique has been employed to determine the solubility of oxygen in liquid pure silver and the effect on the oxygen solubility of solute metal additions to liquid silver. The results indicate that oxygen deviates slightly from Sieverts' law in pure silver as = 3.9. Gold, platinum, md palladium decrease the solubility of oxygen in silver. First-order free energy, enthalpy, md entropy interaction coefficients are determined from the data. An important aspect in the establishment of the formalisms to be applied to represent the thermody-namic behavior of components of solutions is the accuracy of the experimentally determined thermody-namic properties. Wagner developed the first-order free energy interaction coefficient.' Recent papers2'3 extend the treatment formally to other thermodynamic properties and define the second- and higher-order interaction coefficients. A current communication4 considers in some depth the requirements and limitations imposed because of experimental error on the use of several formalisms now under active consideration in the field. This communication reports the results of an experimental study of the behavior of oxygen in liquid silver alloys that was carried out concurrently with the development of Refs. 2 and 3 with the hope of providing sufficiently precise information so that enthalpy and entropy interaction coefficients could be determined. THE EXPERIMENTS The Sieverts technique was employed using an improved design of the reaction bulb over that developed originally by Humbert5 and subsequently improved by pehlke6 and Weinstein.7 The Vycor reaction bulb as shown in Fig. 1 was air-cooled and contained a port for the thermocouple angling off to one side and a vertical port for connections to the gas supply and

Jan 1, 1969

By E. R. Atkins, G. H. Smith

Results of laboratory tests are presented to show that lire value of "m", in the Archie expression dernlined by the shapes of the particles in the system. Tile value of m "the shape factor", is constant for a system of particles of a given shape for a range of F - + values. Applying this concept, one can predict F - + relationships for mixtures of particles with different shapes, and these predicted relationships are useful in electric log interpretation. It is suggested that an equation of the form 1/F -10mcan be used to describe the properties of natural formations containing varying amounts of sand and clay. From this work and values of "a" and "m" reported in the literature, it appears that in many cases rocks in the same geological horizon have a common primary porosity but contain varying amounts of a particular clay. It is concluded that the equation can be applied to a rock-water system only when values of "a" and "m" have been established for the particular system. INTRODUCTION The petroleum literature contains many reports of the results obtained by determining formation resistivity factor F and porosity + of rock samples from oil fields all over the world. The usual practice is to use data from a large number of samples from a number of fields to find an average relationship between F and +. Several such average relationships have been advanced. In the absence of data on a particular formation or field, it has been the practice to use the average relationships to give a rough approximation of the F - + relationship. The purpose of this paper is to report on basic relationships that exist between F and + for naturally occurring particles in water solutions. Other workers' have found the same relationships apply to the diffusion of hydrogen through packed beds of dry particles. In the work discussed here, relationships for application to unconsolidated sands or shales containing mix- tures of particle shapes are derived. These relationships, developed for unconsolidated formations, may apply to consolidated formations. EXPERIMENTAL To evaluate F- relationships for unconsolidated rocks, the results of laboratory measurements on simple slurries of clay or sand will be used. Such laboratory studies are concerned with the electrical behavior of water-containing rocks. The wet rock constituents are electrically similar in slurries and in rocks. Archie2 defined formation resistivity factor as All resistance measurements were made using a 1,000-cycle impedance bridge with an oscilloscope as the null detector." The accuracy of this bridge was better than * 0.15 per cent. For the particular apparatus employed, no additional reactance was required to achieve balance for samples with resistances between

THE program for the 126th meeting of the Institute, to be held in San Francisco Sept. 25 to 29, 1922, is being prepared by the General Arrangements Committee of the Local Section and its details are not yet ready for announcement. The program, however, has developed to a sufficient extent to permit members to decide whether they wish to attend or not. Briefly stated, Monday, Sept. 25, will be devoted to technical sessions which will be held at the Engineers Club, and there will be as many sessions as may be required to present the papers available, some of which are listed below. Under the registration fee plan (see July magazine) entertainment expenses during the week in San Fran-cisco will be borne by those in attendance, not by local members alone. Members who expect to attend the San Francisco meeting, but who will not accompany the President's party, will please notify C. H. Fry, Secretary of the San Francisco Section, 625 Market St., San Francisco, Cal., of their intention.

Jan 8, 1922

By A. M. Gaudin, W. D. Charles

IN flotation lime is used to depress pyrite. For this purpose it is preferred to caustic soda. The low cost of lime and the widespread availability largely account for this preference. However, there is some evidence' that pyrite is more readily depressed by calcium than by sodium ions at the same pH. To measure the difference in adsorption of calcium and sodium, which is thought to lie at the basis of the differences in depressing action, radionuclides of calcium and sodium have been used. The experimental work has included an evaluation of the effect of dissolved oxygen, of the concentration of calcium or sodium, of the concentration of hydrogen ion, and of the anions present. Preliminary work in the investigation entailed preparation of the pyrite, development of a technique for counting pyrite coated with Ca and Na, the radionuclides used, and development of an apparatus to study the adsorption of calcium and sodium on pyrite. The main experimental work included calcium adsorption and sodium adsorption studies detailed below. The following are the most salient observations made during these experiments. Oxygen in solution increases the adsorptive power of pyrite for calcium

Jan 1, 1954

By C. H. Mathewson, A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By L. C. Brown, E. B. Hawbolt

If a single-phase alloy is rapidly cooled such that insufficient time is available for an equilibrium transformation to occur, the high-temperature phase may be retained to room temperature or may undergo a massive or martensitic reaction. The massive or martensitic product develops without a composition change and usually has a crystal structure approximating an adjacent equilibrium phase. The characteristics of a massive transformation are intermediate between the equilibrium reaction in which long-

Jan 1, 1969

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

By Frederick N. Rhines

BECAUSE of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding 'their occurrence, even though the fundamental mechanisms involved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpret the next. It is the purpose of the present paper to present, by means of examples drawn from practice, a brief survey, of the ways in which gas-metal diffusion serves and obstructs the purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with but brief mention of parallel cases. THE NATURE OF GAS-METAL DIFFUSION The term "gas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to- regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. No element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

In the late 19th century Fremont Pass was only a gateway to Leadville, Colo., 12 miles to the north. Some of the silver, lead, and zinc won from this famous camp crossed the Continental Divide at Climax, passing by the huge outcrop of molybdenum on Bartlett Mountain. This element, relatively un- known in the world of commerce, was then nothing more than a joke to play on greenhorn prospectors. Even 30 or 40 years later, after the demand for metals created by World War I had forced temporary use of molybdenum as an alternate for tungsten in tool steels, the Bartlett Mountain outcrop once again became merely a curiosity. With the persistent efforts of Brainerd Phillipson, for years the president of Climax and almost the only employe, use of molybdenum gradually began to grow, first in tool steel and later in the alloy steels required by the growing automotive industry. Mr. Phillipson was first an engineer and second a salesman. The combination of these two qualities is the key to the story, not only of Climax sales but also of the growth of molybdenum from an object of idle curiosity to the point where it is today, along with chromium and nickel, one of the most versatile alloying elements in the iron and steel industries and increasingly important in chemistry.

Aug 1, 1955

By Morris A. Dodd

The nodulizing process described converts finely divided zinc calcine into a dense purified nodule. These zinc nodules are suitable for direct use in zinc reduction furnaces, especially the horizontal retort type, for the production of metal or American process zinc oxide furnaces for producing lead free zinc oxide. The basic reactions are carried out in a rotary kiln fired with fuel oil or natural gas. The combustion gases travel countercurrent to the flow of the zinc bearing material. Volatile impurities are carried out of the kiln with the combustion gases and a small portion of the finely divided feed material. The gases are cooled and the larger solid particles are separated from the stream before the resultant fume is collected in a conventional cloth filter baghouse. The fume collected can be further processed by conventional wet processes for the recovery of metallic values such as lead and cadmium. In order to nodulize the calcine properly it is elevated to a point of incipient fusion. The agglomerated material falling from the kiln is cooled and then sized by passing through a screening and crushing system consisting of a jaw crusher and a roll crusher in closed circuit with a vibrating screen.

Jan 1, 1970

By H. l. Burghoff

DURING the course of preparation of crystals of alpha brass for an investigation of their creep characteristics, a number of critically oriented crystals were produced. In each of these specimens, P0, the specimen axis, lay near some important crystallographic direction or on or near the border of two possible slip systems. Because of the unusual nature of their orientations, it was considered of interest to deform these speci-mens in simple tension and to study orientation changes and any unusual occurrences, different from what would be expected for specimens in which only one slip system had distinctly the highest maximum resolved shear stress. Choice of actual operating slip system in a crystal offering an immedi-ate possibility of two slip systems would be expected to be due to chance, defect, or some inhomogeneity. Even in an ideally perfect crystal so oriented, the natural oscillations of the atoms about their lattice positions would give rise to a condition wherein one slip system would be favored over the other at the critical shear stress. In the large, nonperfect crystals of the present investigation, slip on both systems, but in different portions of the specimen, might occasionally be expected.

Jan 1, 1940