Search Documents

By Hoyt Stoddard Gale

Recent work on borate deposits near Kramer in the extreme southeast corner of Kern County, California, is of special interest because of the information it seems to give concerning the mode of origin of the borate minerals colemanite and ulexite, especially when considered in conjunction with the valuable clue to the mode of origin of colemanite in its present known deposits given in a paper by W. F. Foshag,1 of the United States National Museum. Colemanite is found in or near original deposits of ulexite, from which it is supposed to have been derived by a change in the character of the ground water or rate of its movement or both. Indications that an alteration of this sort had produced colemanite were first recognized by the writer2 in specimens collected in the Kramer district in 1920, and sent to W. T. Schaller, at U. S. Geological Survey, for identification. The identity of the two borate minerals in these specimens was suspected when collected but not at once determined, but the relations of the minerals as seen in the specimens seemed to afford a manifest clue to the origin of the deposits. Similar specimens were obtained by the writer from deposits in Death Valley soon after he had examined the deposits near Kramer. After studying the specimens submitted to him Dr. Schaller wrote as follows: " I have finally positively identified the boron minerals you sent me with your letter of Sept. 27. The 'white fibrous mineral like ulexite, is ulexite; the 'harder nodules' in the clay are colemanite, apparently formed from the ulexite as a result of leaching, with recrystallization in place—a theory that Foshag is working on." The present paper is a report on the facts observed at the depo its near Kramer, and some general observations on the geological relations noted, which, unfortunately, still form only a very incomplete record. The intimate association of deposits of colemanite and ulexite in California and Nevada with certain volcanic rocks affords a strong pre-

Jan 1, 1926

By J. J. Gilman

WHEN a zinc crystal is immersed in liquid N, and then plastically bent, it is observed that it bends a certain amount and then fractures. This fracture occurs at a fairly reproducible radius of curvature, and the radius varies systematically with the crystal orientation. Because this phenomenon provides an unusually well-defined set of fracture conditions, it is possible to examine various possible fracture criteria and select the best one. Zinc crystals of various orientations were bent about axes lying in their glide planes (0001) and perpendicular to their glide directions [1210]. The crystals were 0.150 in. diam and had chemically polished surfaces. They were immersed in liquid N, while they were being loaded on an Instron testing machine. A three-point bending jig was used to load them. Table I lists the beam radius at which fracture occurred for each orientation. Each value is the average of at least six measurements. The normal stresses on the cleavage planes, at the time of fracture, were calculated as follows: First, from the fracture radius, R,, the orientation angle, x,, of the (0001) plane at the outer fiber was calculated. If x, = angle between the (0001) and the rod axis prior to bending, d = rod diameter, and X, = angle between the (0001) plane and a tangent to the bent crystal, then1 sinX, _ 2R, sin xn 2R, + d Since the glide shear strain is given by' y ' cot X, — Xo the glide strain at fracture, x,, can be calculated. Next, it is necessary to know the tangential stress in the outer fiber at fracture. This depends on the plastic flow curve, so a series of tensile tests were performed at —196°C on another set of zinc crystals. A curve of the average resolved shear stress versus glide strain was prepared. From this curve, shear stresses, r,, corresponding to the glide strains in the bend tests were taken. These values are listed in Table I. Then the normal stresses in the outer fibres, u,, were calculated from the relation U, = r, tan X, This analysis assumes that the fiber stresses in a bent beam are the same as the stresses in simple

Jan 1, 1959

By R. Woodward Moore

A GRAPHICAL method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application.

Jan 1, 1944

By C. K. Rose, J. H. East

Proved oil shale reserves in the Green River formation in Colorado, Utah, and Wyoming dwarf present U. S. petroleum resources. Indications are that the appetite for petroleum products will continue to grow and that this potential source of liquid fuels and related byproducts cannot be disregarded. As a part of its synthetic fuels program, the U. S. Bureau of Mines has opened a mine in the richer beds on the naval oil shale reserves. In addition to supplying material for retorting and refining studies, the development of methods, procedures, and equipment for mining oil shale on a large-scale commercial basis is of the greatest importance.

Oct 1, 1955

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By John J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these .melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. In the early days, the process was thought of as a simple one. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. Using cryoscopic data, Rolin has determined the following composition for molten cryolite. Na2,AlF 3Na + 3F + AlF [1] He postulates the following equation for the ioniza-tion of alumina at low concentrations Al2O3 Al + AlO2 +O. [2] At concentrations above 0.025M he supposes the ionization of alumina to proceed as follows Al2O3 AlO + AlO2. [3] Rolin's mechanism of electrolysis for the more concentrated solution in Eq. 3 is as follows. The AlO' ion migrates to the cathode. where it is dis- charged, giving metallic aluminum and 0' ions which migrate to the anode. The AlO2- ion migrates to the anode, where it is discharged, giving Al ions and oxygen which reacts with carbon to form CO2 In the case of the extremely dilute solution in Eq. 2 the Al ion migrates to the cathode and the AlO2-and 0 migrate to the anode as before. Another possible mechanism for the electrolysis follows. Ionization of Cryolite Na3AlF4 = 2Na + 2F + NaAlF, Na + AlF-AlF+Na + F [4] Addition of Alumina 2Na2AlF+ 2AL2O4 6Na + 3A12O3F4 [5a] Al2O2F 2AlOF2 [5b] Cathode Process AlF, + 3e+ 4F + Al. [6] Anode Process AlOF2 + 2F AlF1 + 1/20, + 2e or A12O2F + 4F-2A1F; + 0, + 4e. [7] Although both Rolin's and the present mechanism of the Hall process may be qualitatively satisfactory, present data are not adequate for quantitative tests of the theories.

Jan 1, 1959

By George Tryon, E. A. Barnard

The importance of the conservation of the waste heat contained in copper reverberatory furnace gases was realized very early by those in charge of operation at Anaconda. The first attempt to utilize it was in preheating the air used for combustion of the coal. This was done by forcing the air through ducts surrounding the flue-gas downtake and continued down beneath the furnace hearth to the firebox. Any small advantage gained by the heat transferred from the flue gases was more than offset by the losses sustained in cooling the hearth, therefore this process, after several trials, was soon discarded. It was first used at the Old Works as early as 1893 and again for a comparatively short time on the original furnaces at the Washoe smelter, or present works. Water-tube boilers came into general use very rapidly after 1890. Their adaptability for waste-heat steam generation, as well as the saving to be effected by the production of cheap steam from this source, was soon recognized. The first waste-heat boiler to be used in connection with a matte furnace at Anaconda was installed in September, 1900, at the "Old Lower Works." It consisted of a 100-hp. "Cook," vertical water-tube boiler. This boiler had 65 small perpendicular tubes arranged in concentric circles around a 10-in. tube in the center. These tubes were expanded into 4 ft. 4 in. inside diameter cylindrical steel top and bottom drums which served as the steam and mud drums respectively. This boiler was set in a cylindrical brick housing into which the furnace gases entered just above the mud drum and thence circulated upward around the tubes and steam drum to the stack. This installation proved unsatisfactory, presumably on account of difficulty with dust, and was soon abandoned. However, the possibilities for steam generation were undoubtedly encouraging for shortly afterwards (December, 1900) a 300-hp. Stirling boiler was installed, to be followed by two more in the spring of 1901. The choice of the Stirling type of boiler for application to copper reverberatory furnaces was particularly fortunate, as the arrangement of the tubes appears to combine to a great extent the maximum contact of the gases with the heating surfaces of the boiler and at the same time

Jan 1, 1934

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By Rip Thompson

ALTHOUGH the metallurgical treatment for the Ophir Hill tailings was developed more than 20 years ago and in the interim a vast amount of experimental work was done with later-developed flotation rea-gents, it was found necessary to revert to the original oil reagents and their combina-tions with specific chemical reagents in order to obtain results of economic value. This is of especial interest because in present ore-treatment investigations later-developed flotation reagents are used almost exclusively and the coal-tar deriva-tives, except in certain patented reagents, are virtually neglected. These coal-tar oils and derivatives still have a definite field of application, especially in the treatment of some oxidized ores when modified sulphidi-zation is desirable. The Ophir Hill tailings deposit is in Ophir Canyon, Tooele County, Utah, about 55 miles southwest of Salt Lake City and 25 miles south of the Tooele smelter of the International Smelting and Refining Co. A road good for trucks leads directly from the Ophir mill to the smelter.

Jan 1, 1940

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By M. J. Hart, E. C. McDowell

There are no formulas that guarantee success when obtaining zoning approval for mineral aggregate mining. Local land use decisions often represent the most controversial issues faced by a community. Public awareness, concern, willingness to get involved, sensitivity to the environment and, probably most important, fear of change only begin to describe the atmosphere in which local land use decisions are made. The public hearing process is quasi judicial, adversarial, and unfortunately, not designed for resolution of disputes. It is not difficult to see the need for an alternative to present methods. Hopefully, some day there will be a process that will do away with or at least minimize unnecessary, unproductive, and unmanageable community conflicts.

Jan 1, 1986

By Hisaaki Takada, Atsushi Yoshida, Kazuo Satoh, Norikazu Nanko, Naoshichi Higashi

Kamioka Mine of Mitsui Mining & Smelting Co., Ltd. is the largest lead-zinc mine in Japan and is composed of two mines, Tochibora Mine and Mozumi Mine, which have daily production rates of 5,200 metric tons and 1,800 metric tons of crude ore respectively. In the mines, there are many massive pyro-metasomatic deposits which have been derived from the replacement of limestone. The deposits are composed of skarn minerals which mainly contain hedenberite. The country rock is generally hard and fine-grained gneiss. These deposits have been mined by means of the sublevel stoping method, induced block caving method and sublevel caving method at Tochibora Mine and mainly by the cut and fill method at Mozumi Mine. Since the 19601s, the trackless mining system has been introduced successfully into both mines, and is still promoted to be applied over wider areas. The underground hauling system is simplified remark- ably and much improved by adopting trackless ramps to the existing vertical and horizontal underground framework. Moreover, through the combination of the trackless mining system with the mining methods stated above, a notable increase in efficiency has been achieved. This is due to the high performance of the introduced machinery, reductions in man power of miscellaneous jobs, and also has enabled a highly efficient performance through its mobility. In addition, as it becomes possible to realize a flexible development to meet the irregularly shaped deposits and also becomes much easier to recover the remaining pillars by secondary mining, the extraction rate of ore has been improved considerably. With the introduction of the trackless mining system, the development method has been changed, thus former hand-hold leg-drills are now mostly re- placed by jumbo-type drills. Repair shops for Load-Haul-Dump machines also have been provided with an established service system. Reinforcement and rearrangement of the ventilation system has been carried out.

Jan 1, 1977

By Dale Nix

DuRing the past year approximately 400 depth pressures have been recorded in the Yates field. Of these, 315 were "shut-in depth pressures," observed for the purpose of adjusting well potentials without making open-flow tests. The "shut-in depth pressures" were distributed one to each well and determined under as nearly uniform conditions as possible. Therefore, there is a scarcity of data applicable to production problems, other than the adjusting of well potentials. A few of the data obtained have been used in an attempt to solve some of the producing problems. These applications, however, merely indicate partial solutions and their review herein is to emphasize the variety of problems to which depth-pressure data can be applied, rather than to present conclusive solutions. Very little had been accomplished in the development of instruments to determine pressures within the well bore, when it was decided to obtain such information in the Yates field. Through the combined efforts of the Yates Engineering Committee and several producing companies, three methods of determining pressures in the well bore were soon developed: (1) the "compressor" method, (2) the "volume chamber" method, (3) the "depth-pressure recorder" method. "Compressor" Method.—A small volume compressor is used to inject gas into the tubing. The rate of injection is low so that the frictional losses will be reduced to a minimum. During the test, the pressures at the top of the tubing and casing are observed on recording pressure gages. .As the compressed gas depresses the fluid in the tubing, the pressure on the casing decreases while the tubing pressure increases. The tubing pressure becomes a maximum when the fluid level reaches the bottom of the tubing; and the casing pressure usually rises quickly as the gas breaks around the bottom of the tubing. The sum of the maximum pressure recorded at the top of the tubing and the pressure exerted by the weight of the compressed gas column is equal to the depth pressure at the bottom of the tubing. The procedure can be reversed;

Jan 1, 1932

JAMES E. HOWARD,* Washington, D. C. (written discussion?). -Mr. Comstock, in his classification of the possible causes of transverse fissures, has not quite caught the point of view of the writer. It appears, following the trend of thought in Mr. Comstock's paper, that three groups instead of two might bee enumerated, namely: Fatigue of the steel, quality or, preferably, grade of steel, and mill practice. All steels are liable to failure by fatigue. Stresses that are capable of causing fatigue fractures are modified in their magnitude by the grade of steel acted upon. Mill practice is a term having a very wide meaning and in its relations to the development of transverse fissures has been used with such vagueness as to include many known factors and some that are unknown in the arts. According to the grade of steel employed, fatigue fractures may be accomplished by loads of greater or less magnitude, hence there is a relation between quality, or grade, of steel and the display of fatigue fractures. Mill practice of such an order as to affect the formation of transverse fissures must be shown to exert an influence on the ability of the steel to endure repeated stresses. Different grades of steel are selected for different purposes. Steel employed for fire-box purposes is of different grade from that used for cutting tools; although each grade is suitable for its purpose, and therefore of good quality. It is conceivable that a demand might be made for steel of physical properties in excess of those of any known grade. Under such a demand, impossible of' fulfillment, it would not be proper to refer to the steels as being deficient in quality; to do so would be a failure to recognize that all steels have their limitations in strength. Service conditions peculiar to rails admit of successive advance until the conditions can no longer-be met. The failure of a large number of rails from one type of failure, when all known means of averting the failure have been employed without success, is sufficient evidence that the end is close at hand. Iron rails, for a time, successfully met the requirements of railway service but weight of equipment, motive power, and rolling stock were increased, necessitating the use of steel. The early steel rails enjoyed the reputation of being of excellent quality, although: neither chemically nor structurally would they be so regarded ,lit the present time. They did good service in their day and under the conditions then prevailing were good rails. To meet the increased weight of rolling stock there has been

Jan 3, 1919

By Marston G. Fleming

CRITICAL pH has been defined by Wark1 as that pH value below which a mineral will float and above which it will not float in solutions containing a given concentration of collector but free from other depressants or activators. - The relationship between mineral, collector concentration, and pH is expressed in the form of a critical pH curve determined by the captive bubble method and is generally regarded as being fundamental to the system involved. The mechanism of alkali depression is currently in dispute, two general theories having received authoritative support. The view expressed in Taggart's chemical theory of flotation2 is that in the presence of a critical concentration of hydroxyl ions, all the metal ions available at the surface of the mineral are present as anions of the form [M (OH)x]-y. The formation of the necessary metal xanthate is thus precluded and, furthermore, any metal xanthate coating previously formed, at a lower pH, will be dissolved. Gaudin3,4 and the Melbourne school under Ware hold that alkali depression is caused by the preferential adsorption of hydroxyl ions by the mineral surfaces. This paper describes an investigation of the mechanism of alkali depression in each of the three systems: cerussite-aqueous carbonate-xanthate, cerussite-xanthate, and galena-xanthate. Alkali Depression of Cerussite by Control of Carbonate Ion Concentration Wark and Cox6 have shown that in the presence of Na2CO3 a higher concentration of xanthate is required to effect bubble contact with a cerussite surface than in carbonate-free solutions. To examine this depression of cerussite by sodium carbonate, a series of captive bubble tests was carried out on cerussite specimens in solutions containing 100 mg per liter of potassium ethyl xanthate and varying concentrations of sodium carbonate. The pH was adjusted by the addition of dilute hydrochloric acid. For purposes of comparison a standard critical pH curve was determined for cerussite with potassium ethyl xanthate in solutions containing no added carbonate. In the latter case pH adjustment was made with sodium hydroxide. The experimental method employed in both series was broadly similar to that described by Wark and Cox;7-9 a number of refinements suggested by Sutherland10 were adopted, and the procedure was further developed and modified to suit the particular requirements of the investigation. The relationship between pH and the concentration of potassium ethyl xanthate necessary to induce bubble contact at cerussite surfaces is shown in Fig. 1. The relationship between pH and the concentra- [ ] tion of sodium carbonate necessary to prevent bubble contact at cerussite surfaces in the presence of 100 mg per liter of potassium ethyl xanthate is shown in Fig. 2. Comparison of the. two curves shows that at a collector concentration of 100 mg

Jan 1, 1952

By Warren T. Smith

The Phelps Dodge Corp. Lavender pit is located in the Bisbee mining district near the town of Lowell, Ariz. A quartz monzonite porphyry exists as an intrusive stock and was the source of mineralization for the limestone replacement orebodies being mined by underground methods. Leaching of the upper portion of the stock, and precipitation of the copper as chalcocite on the finely dispersed un- oxidized pyrite in the monzonite porphyry, formed a low grade ore zone below a leached capping varying from 50 to 300 ft thick. Churn drilling starting in 1916 and supplemental churn drilling begun early in 1950 indicated a mineable area about 3100 ft long by 2400 ft wide. In general drilling was on 100-ft centers. The pit was planned with 50-ft benches and wall slopes varying from 1 to 1 to a flatter slope of 1 1/3 to 1 dependent on the character of the ground. Materials within the pit limits, using a 0.6 pct minimum grade cutoff, were estimated at 41 million tons of 1.14 pct copper ore, 31 million tons of low grade sulfides suitable for leaching with an average grade of 0.42 pct, and 70 million tons of waste.

May 1, 1956

By F. W. Bloecher, A. M. Gaudin

Using an adsorption-column technique the partition of dodecylamine between quartz and water has been determined at concentrations ranging from 0.5 to 4000 mg per liter. The adsorption varies as the square root of the concentration. Attachment of dodecylamine to quartz is reversible. The amount adsorbed in a flotation operation giving almost complete recovery is under 5 pct of the amount required for a monolayer.

Jan 4, 1950

By H. Landsberg

SUBSIDENCE caused by mining operations has been a matter of interest for the mining engineer for just 111 years, since the Belgian Committee for study of subsidence in the city of Liege submitted its first report in 1825. This interest is fairly expressed in the enormous amount of literature that has since appeared on this subject. A bibliography, probably far from being complete, which preceded this study as a pre-liminary survey, comprises more than 800 titles. In spite of this fact the problem remains today as acute as it has ever been. The questions of as good a recovery as possible of the national resources, the safety of the operations, and the protection of private and public property are the important angles from which to look at the problem.

Jan 1, 1936

By W. B. Phillips

The earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in " Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. ***** The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would be thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.' In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114, Township 6, contains 79.08 grains of free sillphuric acid per gallon. This locality is about 13 miles (21 km.) south . of Delaware Creek and about 35 miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos. Texas is in the Pirst Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 1, 1918

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min. is required to drain and dress the furnace hearth, make up the tap hole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays, because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of' charge. Such general considerations are dealt with first. GENERAL CHARGING PRACTICE Charge materials are discussed in detail in Chapter IV; the present chapter is concerned with the charging, melting, and proportioning of the raw materials in the various types of furnace practice. Charging Equipment and Stock Handling. The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment described in Chapter I (see also Fig. 18, page 33). It is generally desirable to charge the scrap about as fast as the physical volume can be got into the furnace. A limiting factor may be the height to which the scrap may be piled in the furnace without deflecting the flame to such an extent that it will impinge on the roof or walls and thus damage the refractories, but light scrap may often be piled up near the roof since the flame usually "cuts it down" rapidly before impingement on any roof area can persist long enough to do appreciable harm. When the nature of the scrap and the handling facilities are adequate to meet the aim of rapid charging, little thought is given to this feature of operation. Unfortunately, at times

Jan 1, 1944