Search Documents

By G. Sachs, A. W. Dana, C. C. Chow

A great number of the investigations on the plastic flow of metals have been concerned with the establishment of a "universal" stress-strain relation. In such a relation some stress function when plotted against a strain function should yield identical curves for the various stress states. In the first investigation of this type, Ludwik and Scheu1 plotted the maximum shearing stress as a function of the maximum principal strain. Later Ros and Eichinger2 introduced two universal stress-strain relations, the one relating the maximum shearing stress to the maximum shearing strain, and the other relating a stress invariant, suggested by von Mises and Haigh, to the corresponding strain invariant. (In more recent investigations the stress and strain invariants are frequently supplemented with some factor to render their meaning more lucid.) A further suggestion which has not attracted appreciable attention is that by Baranski³ who used stress and strain deviators. The most common means of experimentation to determine the relation between stress and strain consists in subjecting thin walled tubes to combined internal pressure and axial tension.4a,4b,4c This method allows the study of plastic flow under stresses which are variable in two directions. However, the plastic flow which can be obtained in this manner is comparatively small, being limited by either tension failure or instability. For copper,'. only the relation between maximum shearing stress and maximum shearing strain yielded good agreement. On the other hand, tests on a stee14b and on an aluminum alloy4c. resulted in systematic deviations if any of the discussed universal stress-strain relations were used. It would seem, therefore, that the agreement mentioned above for copper is only incidental and explained by its high rate of strain hardening compared to that of other metals. Much larger strains than experienced in the tube tests can be obtained by subjecting a thin membrane of a ductile metal, which is restrained at its periphery, to a uniform hydraulic pressure. The thin sheet forms a deep bulge before it fails. The stresses and strains in such a bulge increase with increasing distance from the edge of the clamping "die," the maximum stresses and strains occurring at the pole (crown) of the bulge. While the stress and strain states are determined by the contour of the bulge, the absolute magnitude of the stresses and strains depends upon the hydraulic pressure. The bulge contour is in turn correlated with the geometry of the die opening. The deformation and fracture characteristics of circular bulges, that is, bulges formed with circular clamping dies, have been the subject of numerous experimental and analytical investi-gations.5,6,7 It has been shown that plastically deformed circular bulges develop large and comparatively uniform strains before failure by instability"6b,6c,6d and closely assume a spherical shape.6d Also the distribution of strains across the contour of the bulge is dependent on the metal being investigated and is correlated with, but cannot be predicted from, the metal's stress-strain characteristics. On the other hand, oblong or elliptical bulges, that is, bulges formed with elliptical clamping dies, are not as susceptible to analytical analysis and have not been investigated to the extent that circular bulges have. The few available data6c,7c indicate that stress states are obtained at the poles of the bulges, varying between plane strain and balanced biaxial tension, depending upon the geometry of the die opening. In this paper, the strain state and curvatures exhibited by three bulge shapes, a circular and two elliptical bulges, Fig 1, are analyzed experimentally using methods described in previous publications.6a,6c An attempt is made to derive the stress-strain relations for these bulges, which represent strain states in which the ratio of the two positive principal strains varied between 1.0 and 0.35. In addition, tension tests yielded data for a value of —0.5 for this strain ratio. Such an analysis should indicate the applicability of the various laws correlating stress with strain to the stress and strain states occurring in bulged shapes. Definitions and Nomenclature The definitions of the major stress and strain quantities used in this paper are as follows: s1, s2, s3 = principal normal stresses Sl > s2 > S3 t = shear stress e = conventional (unit) strain e = In (1 + e) El, E2, E3 = principal natural strains 7 = shear strain The maximum shear stress: , _ S1 — S3 lmax = 2 Frequently, the flow stress, s1 — s3 = 2lmax rather than the maximum shear stress is used.

Jan 1, 1950

By Arthur S. Dwight

We author of this historical chapter will perhaps be criticized for limiting his subject to the history of the blast furnace in lead smelting, and especially to the part it played in the great custom ore-smelting business which for three decades or more was the means of opening up vast mineral treasures and practically dominated the mining industry in the Rocky Mountain region of the United States, in Mexico and in Canada. The men of that era shared the romance and the thrills of mining, and bore their part as pioneers in the building of the great West. The present writer was too young to participate in the first of the three decades mentioned, but immediately thereafter came under the apprenticeship of some of the men who had worked out the early metallurgical problems of the industry, became personally acquainted with most of the others of that group, heard the tales of early experiences, successes and failures, the gossip of the frontier and mining camps, from all of which there remain embedded in his mind clear impressions of the outstanding personalities of that time. That is the background against which the fifty years of intimate contact with the mining and smelting business and his own experiences as metallurgist stand out in his memory, and it is hoped that the gentle reader may understand and approve his desire to rescue from comparative oblivion the fundamentally valuable results accomplished by these fathers of the industry. It will be the purpose of this chapter first to narrate the general history of the growth of the industry; second, to pay tribute to some of the pioneer metallurgists, and third, to discuss some of the salient points of the metallurgical practice at different periods, to illustrate the technical progress of the art. The series of eight Annual Reports of Rossiter W. Raymondl,† U. S. Commissioner of Mining Statistics from 1869 to 1876, contain most of the available information about the early smelting operations in the Rocky Mountain region, and much is in the early volumes of the Transactions of the American Institute of Mining Engineers. The monograph by S. F. Emmons2 though not published until 1886, contained an elaborate description of the smelting works operating in 1879. Otto H. Hahn3 wrote a valuable paper in 1883, on smelting prac-

Jan 1, 1937

By H. W. Schull

The Alligator Ridge gold deposits are located in northwest White Pine County at the southwest end of Alligator Ridge. Alligator Ridge is on the west side of Long Valley in the range of hills that separates Long and Newark valleys. The nearest population center is Ely, about 113 km (70 miles) to the southeast. Access to the Alligator Ridge gold mine from Ely is via US Highway 50 and the Long Valley Ruby Marsh Road. The latitude and longitude is approximately 39° 45' north and 116° 30' west. The Alligator Ridge gold deposits occur in the lower 61 m (200 ft) of the Mississippian-Devonian Pilot Shale formation, a laminated calcareous carbonaceous siltstone. The gold deposits contain carbonaceous, oxide, and jasperoid type gold ore. For more details on the geologic features of the deposits, see Schull, Sutherland, and Ilchik (in press). The discovery story of Alligator Ridge began in the spring of 1976 when the areas mapped as jasperoid on the 1:250,000 scale geologic map of White Pine County (Hose and Blake, 1976) were examined and sampled. Seventeen samples, about 23 kg (50 lb), were collected from an area about 0.65 km2 (0.25 sq mile). Of these 17 samples 10 reported atomic absorption values of less than 0. 1 ppm Au and 7 reported values in the 0.1 to 1.0 ppm Au range. In June of 1976 20 lode claims were staked to claim the area of the rock chip sampling. The claims' end and side center lines were used as a grid for soil sampling. Sample stations were 91 m (300 ft) apart and sample lines were 229 m (750 ft) apart. The samples were sieved to - 180 µm (- 80 mesh). Out of 99 soil samples, seven samples reported Au values in the 0.1 to 1.0 ppm range. Of the seven auriferous samples, five were located over the jasperoid outcrops previously sampled; one over unmineralized Pilot Shale a few hundred m (ft) downslope from some Au-bearing jasperoid; and one from a 15 x 15 m (50 x 50 ft) talus outcrop area of hitherto unnoticed mineralized Pilot Shale. Subsequent sampling, mapping and drilling would show that this 15 X 15 m (50 x 50 ft) outcrop area was the top of the Vantage 1 ore body, about 1.27 Mt (1,400,000 st) of over 3 g/0.9 t (0.11 oz/st) Au. Late in the summer of 1976 about 30 more 1.4 to 2.2 kg (3 to 5 lb) rock chip samples were collected in the course of preliminary geologic mapping. This mapping and sampling showed that the gold-bearing jasperoids occurred at the contact between the Pilot Shale and the underlying Devils Gate Limestone. Rock chip samples of 0.1 ppm Au or greater were restricted to the jasperoids and the mineralized outcrop area of Pilot Shale located by the soil sample survey. Rock chip samples from the area of mineralized Pilot Shale were in the 3 to 5 ppm Au range. Activity resumed in the summer of 1977 with a more detailed soil geochemical survey. The jasperoid areas were defined as large geochemical gold anomalies of values greater than 0.1 ppm and locally greater than 0.2 ppm Au. Soil samples from the area of mineralized Pilot Shale outlined a greater than 0.1 ppm gold anomaly 61 x 152 m (200 x 500 ft) in size. Further geologic mapping showed that elsewhere, even where bleached and silicified, the Pilot Shale areas were geochemically very low in gold (less than 0.1 ppm Au). In November, 1977 twelve rotary percussion drill holes were drilled to test the gold-bearing jasperoid areas and the mineralized Pilot Shale area. Drilling of the jasperoid areas showed that the jasperoids gave way at shallow depths [less than 24 m (80 ft)] to unmineralized unaltered Devils Gate Limestone. A five hole cross pattern was drilled to test the area of mineralized Pilot Shale. Four of the five holes re-

Jan 1, 1985

By D. F. Atkins, B. A. Rogers, E. J. Manthos, M. E. Kirkpatrick

A phase diagram of the uranium-columbium alloys is presented. The apparatus and the procedures used in obtaining the data are described. Data from which the diagram was drawn are given in tabular and graphic form. THE use of uranium in the production of energy from nuclear fission has given considerable im- petus to the investigation of the metal and its alloys. Accordingly, information concerning the phase diagrams of binary alloys of uranium with other elements is of interest to metallurgists engaged in nuclear-engineering activities. As a contribution to the knowledge of the binary alloys, the authors have attempted to establish the diagram of the uranium-columbium system. The reports of laboratories engaged in work for the Manhattan Engineering District and the U. S. Atomic Energy Commission contain a number of references to work on uranium-columbium alloys.

Jan 1, 1959

By Louis A. Panek

Caving of previously undisturbed ground was conducted for a period of about 20 months at two locations about 600 m (2000 ft) apart in an Arizona porphyry copper deposit. When mining was suspended the width of the mined zone at both sites was on the order of one-half the depth and the thickness of ore extracted was only a fraction of the rock column. Thus the results have potential application to predicting the subsidence above a cavern-type excavation. Break cables were used to detect the upward progress of caving. Analytical aerotriangulation was used to determine the vertical and horizontal displacements of 400-plus surface targets covering a 1585 m (5200 ft) square area. The measurements are summarized and interpreted with a view to predicting the rate of rise of a caving brow, detecting the initial surface subsidence, and characterizing the extent, the location, and the varying degrees of expected damage to surface facilities.

Jan 1, 1984

By E. A. Cisney

The formula for calculating the crystallographic angles of a tetragonal lattice is: C°S =where $ is the angle between planes (HKL) and (hkl). The angles in Table I have been calculated for indium

Jan 1, 1960

By E. De Golyer

THE petroleum production of the world, in 1923, for the first time reached the billion-barrel mark. A preliminary estimate of production is 1,014,413,000 bbl., an increase of 159,604,000 bbl., or 18.6 per cent. over the 854,809,000 bbl. produced in 1922, the year of next highest production. This increase resulted from an increase of 178,469,000 bbl. in the production of the United States; the total for the rest of the world shows a loss of 18,865,000 bbl., a loss caused by the decrease of approximately 32,278,000 bbl. in Mexican production. The Mexican decrease more than offset increases in the production of Russia, Persia, Roumania, Venezuela, Sarawak, and various minor fields. The increase in production for the United States, and consequently for the world, was the result of flush production from development to maximum capacity during the year of eight, bonanza fields-fields reaching daily yields of 100,000 bbl. or better. It might be ascribed more exactly to the production from the three flush fields of the Los Angeles basin. Their production alone was greater than the increase in the world petroleum production, or the increase in the production of the United States, and it was cheap oil from these fields that demoralized the oil markets of the world. The Basin fields were. the features and dominating factors in the oil industry of the world during 1923. The bonanza fields of 1923, their estimated production for the year, and peak are given in Table 1.

Jan 3, 1924

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 10 90 10' ohm-cm as compared with 10-6 hm-cm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Where high resistivity with high permeability is desirable, ferrites are used in low frequency applications. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties. During the last two decades the synthesis of ferromagnetic oxides has been the object of extensive research, but commercial production has been started only within the last ten years. Along with more fundamental studies, there remains the never- ending task of developing ways to realize the optimum characteristics of materials in large-scale production. Ordinarily, to produce a ferrite material it is necessary for the constituent oxides to be mixed intimately, pressed, and then fired at temperatures above 1000°C. Ferrite Synthesis: Formation of a basic ferrite by solid state reaction from Fe,O, and a monoxide such as NiO, under normal atmospheric conditions, is governed by a progressive diffusion of cations between adjacent particles of the constituents. Firing temperature, furnace atmosphere, and cooling can vary the magnetic properties, however. If, for example, a dioxide, a sesquioxide, or an oxide of the Me0 type is substituted for the monoxide, the reaction mechanism becomes more complex and extremely dependent on atmospheric conditions and firing cycles. For this reason reproduction often

Jan 1, 1958

By C. L. Prokop

A laboratory investigation has been made of the effects of mud hydraulics upon the formation and erosion of mud filter cakes. The tests were conducted to simulate drilling conditions as nearly as possible. The formation of mud filter cake in a drilling well does not proceed at a uniform and unbroken rate. Instead, the rate of cake accumulation depends upon whether or not the mud is being circulated. If the mud column is quiescent, filter cake formation is a smooth function of the filtration characteristics of the system. If the mud is being circulated filter cake formation depends not only upon the filtration characteristics of the mud but also upon the erosive action of the flowing mud column Filter cakes formed during continuous mud circulation were observed to reach an equilibrium thickness after several hours' circulation. Mud circulation was maintained at a constant volumetric rate throughout each experiment. The fluid velocity at equilibrium cake thickness was dependent upon the thickness of the filter cake. Muds having exceptionally high water loss deposited thick filter cakes in spite of very high eroding velocities. The muds having good filtration characteristics deposited thin filter cakes at equilibrium circulating velocities well within tile range of those in a drilling well. It was observed that filter cakes deposited during stagnant filtration were quite difficult to erode by mud circulation. The - rate of crosion computed from the rate of filtrate accumulation after equilibrium cake thickness had been reached was in reasonable agreement with the rate of erosion obtained by direct observation. Continuous mud circulation usually caused the permeability of the filter cake to decrease with time. INTRODUCTION Many of the difficulties encountered during tile drilling of a well have been attributed to the loss of water from the mud and the attendant deposition of solids upon the walls of the hole. Past experience has shown that a reduction of the filtration rate of the drilling fluid eliminates or greatly reduces these difficulties. Definite filtration requirements, however, are hard to establish for a given set of conditions. This is due. in part, to the fact that the usual filtration test performed upon mud doe? not simulate well conditions as closely as desirable. The filtration characteristics of a mud are customarily determined by means of the standard low-pressure API wall-building tester.' In this instrument a filter cake is deposited upon a horizontal bed under a pressure differential of 100 psi. The rnud is quiescent during the filtration period. In actual practice. mud filtration occurs within a well under quite different conditions. One of the major differences is that mud flows upward across the filter bed as the filter cake forms. This undoubtedly produces a change in the filter cake which cannot be reflected in the results of the API test. The laboratory work described in this paper had as its primary objective a better understanding of the influence of mud circulation upon the thickness and ,characteristics of the filter cakes deposited under conditions similar to those existing in a drilling well. ANALYSIS OF PROBLEM Once a permeable formation is penetrated by the bit, filtrate from the mud flows into the formation. 'he mud solids plaster against the walls of the hole, forming a filter cake. If the mud column is stagnant, that is, if it is not being circulated. the filter cake will increase in thickness until the hole is filled. Prior to the time that the hole is filled, the thickness of filter cake existing at any given time will be a function of the filtration characteristics of the mud, the temperature, and the pressure differential. The effects of these variables have been investigated in the past for both flat bed filtration2'3 and for radial filtration.' When the mud is circulated in a hole in which a filter cake i. being deposited. some of the solids that would ordinarily deposit in the filter cake will be carried away by the eroding action of the mud. This will limit. filter cake thickness. Some work has been done to determine the effect of flow upon the filtration rate in a circulating mud system' but little work has been done upon the factors which determine the filter cake thickness existing in a circulating system. On first sight it would appear that the major factors controlling filter cake formation in a circulating system should be: 1. The rate of deposition of solids from the mud. 2. The erosive force that the flowing mud exerts upon the filter cake. 'A. The erodabilitv of the filter cake. 4. Any change in filter cake characteristics attributable to the scouring action of the mud. The rate at which solids are deposited from the mud will be controlled to a large degree by the filtration characteristics of the mud, the pressure differential. the temperature under

Jan 1, 1952

By Samuel D. Warriner

The dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee, and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able

Jan 1, 1912

By G. Sachs, B. B. Muvdi, E. P. Klier

IT is now generally i-ecognized that hydrogen is responsible for delayed failures encountered in high-strength steels,'.' and the hydrogen responsible for the embrittlement is introduced in the cathodic cleaning and plating operations to which these steels are subjected. Numerous test methods have been used in the past for the determination of brittleness in embrittled parts, namely tension? = notch-tension:' impact,' stress-rupture: a and bend tests.% * Several of these tests are not suitable for routine testing.

Jan 1, 1958

By William Price

DURING the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce risers of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1.

Jan 1, 1937

By W. A. Sheaffer

Electric furnace installation and tough-pitch copper-casting operation at Canadian Copper Refiners Ltd. are described. General layout, power supply and control, refractories, induction pour hearth, casting equipment, metal temperature control, and oxygen-content control are discussed. E LECTRIC furnace at Canadian Copper Refiners Ltd. was put into operation in August 1949. The installation was designed primarily to melt electrolytic copper cathodes and to produce vertically cast tough-pitch shapes. To meet emergencies during reverberatory furnace shut-downs, provision was made for casting horizontal tough-pitch wire bars. Due to the ease with which metal temperatures, melting rates, oxygen content, and casting hours can be altered to suit production demands, the electric furnace has met the requirements admirably. General Layout The plant has been described by H. S. McKnight' and by J. H. Schloen and E. M. Elkin.2 Since these papers were written, the electric furnace has been installed in a 140 ft extension of the original casting building. The extension, 264 ft in width, is divided into one 24 ft and four 60 ft bays, each a continuation of similar bays in the older building. Fig. l, a partial floor plan of the extension, shows the location of major equipment. Power Supply and Control Power for the electric furnace and its auxiliary equipment is delivered by Quebec Hydro over two 12 kv three-phase, 60 cycle pole lines. One line is in use, while the second serves as an emergency standby. Connections for the electric furnace from these lines, which also feed the refinery power house, are made to a substation on Canadian Copper Refiners Ltd. property. Connections between this substation and the furnace transformer room are in underground conduit. The are-furnace transformer, 550 v auxiliary-equipment transformer, and 12 kv switchgear are in the transformer room near the furnace. Stepdown from 12 kv to are-furnace voltages is done by a 7500 kva oil-immersed water-cooled three-phase 60 cycle transformer. This unusually high kva rating is available because the arc furnace and transformer were adapted from a steel-melting unit. Secondary voltages are available in 16 steps between 251 and 95 v (across phases). A four-position tap changer, operated from the furnace switchboard is connected to taps yielding 199, 164.5, 127, and 115 v, respectively. The transformer primary feeder is equipped with a General Electric Magne-Blast circuit breaker. The pour hearth, casting wheel, bosh conveyor, and other auxiliary equipment are fed by a 12 kv to 550 v, 750 kva three-phase 60 cycle transformer. Graphite electrodes, 14 in., with tapered nipples are held in the are-furnace electrode arms with steel wedges. The arms, fed from the transformer secondary busbars by flexible cable bundles, are actuated by winch cables. Direct-current motors operating the winches are supplied by a 250 v motor-generator set. Power input to the furnace is controlled from the furnace switchboard. The board has the usual combination of remote controls for the 12 kv breaker and transformer tap changer, meters, overload relays, automatic and manual electrode motion controls, switchgear, etc. When power is on the furnace, automatic electrode feed is used; the power draw on a given voltage tap then is governed by current-limiting rheostats. The rheostats work through a Westinghouse bal-lanced-beam control circuit which, in turn, operates reversing contactors in the winch motor circuits. Arc Furnace The arc furnace is a standard-type NT Pittsburgh 'Lectromelt with inside shell diameter 12 ft 3¾ in. By hydraulic-lift cylinders, the furnace can be tilted forward to 39 ½ ° and backward to 5" from horizontal. A roof-swing cylinder is also installed but not used. Fig. 2 shows refractory-lining details. With the lining as shown, operating life between repairs is 6 to 9 months of two-shift casting operation. Charge slot, skim door, and roof refractories then are replaced completely, and any necessary repairs made to side walls. Bottom life is longer and the original under courses are still in service, while the top course was replaced in October 1951. The launder is lined with high chrome-magnesite trough brick backed by fireclay and insulating brick. The trough is covered with fireclay brick and asbestos sheet. At intervals, openings 12x6 in. are left in the permanent covering. These are covered with

Jan 1, 1956

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for up- grading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching.

Jan 4, 1953

By R. J. De Angelis, J. B. Cohen, A. Nelson

In this note several recent results on twinning in copper shock-loaded with planar shock waves will be presented and the role of the twins in recrystalliza-tion will be discussed. The twinlike markings first observed in shock-loaded copper by smith1 were identified as twins by De Angelis and Cohen.2 This identification has been confirmed by others.3 In Ref. 2 it was also shown that there is an orientation dependence for twinning at low shock pressures, such that twins in a crystal loaded in [lll] form in the rarefaction or tensile wave but in

Jan 1, 1967

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to overproduce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metalbased economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening.

Jan 4, 1973

By David W. Pasho

The success of a collector vehicle, designed to recover manganese nodules under the conditions which exist in deep ocean mine sites will in part be determined by the effectiveness of pick-up and running gear mechanisms. For the purpose of qualitative comparison, some specific aspects of seafloor interactions with various concepts are reviewed utilizing existing data on seafloor characteristics and running gear/tool interaction with soils.

Jan 1, 1976

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By Thomas W. Gibson

THE Province of Ontario in recent years has come strongly to the front as a producer of metals, especially nickel, copper, silver, and now gold. Of the last named, the output for 1922 was in the neighborhood of $20,000,000. The law governing the mining industry in a community where such develop-ments are taking place will be of interest, therefore, in other places where mining laws are up for revision The first mining of importance done in this province was for copper on the north shore of Lake Huron, where the Bruce mines were opened in 1846. These deposits of copper sulfides, notwithstanding the remoteness from markets and the cost of transportation, were vigorously worked for 12 or 15 years and also intermittently later, but the active career of the mines came to an end in 1875. From first to last, a little less than 10,000 tons of copper was produced, valued at $3,300,000. All the product was shipped to England as dressed ore, contain-ing up to 13 per cent. of the metal. In. 1866, a rich pocket of gold was found on the Richardson farm near Madoc, Hastings County, but was not followed by further discoveries of a like kind and in time the excitement it caused died away. Rich silver ore was found in 1868 on Silver Islet in Lake Superior, a speck of land not larger than a good-sized ball-room. The assemblage of minerals here was practically the same as that at Cobalt, discovered 35 years later, namely, native silver, cobalt, nickel and arsenic; in addition, there was considerable argentite, which has always been scarce at Cobalt. In all, the silver produced amounted to about $3,500,000. The belief persisted that the deposit was not mined out, and in the summer of 1922, some rich ore was extracted from the roof, perilously near the bottom of Lake Superior.

Jan 2, 1923

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction- al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt tension of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984