Search Documents

By L. S. Castleman, H. A. Froot

A study was made of the growth kinetics of B-brass layers in a-brass us y-brass diffusion couples in which both phases were saturated in the 6 phase. It was found that useful estimates can be made of the difhsion coefficients at the ß-phase interfaces from interface displacement data, which are relatively easy to measure experimentally; also, a useful estimate can be made of the mean heat of activation for diffusion from layer growth data. The effects of pressure on layer growth kinetics were explored and found to be consistent with a vacancy model for diffusion in 6 brass in both the disordered and ordered temperature range. 1 HE study of multiphase diffusion receives relatively little attention in comparison with that devoted to diffusion in homogeneous materials. Of the hundred or so papers on diffusion written each year,' only a few are devoted to the subject, and it is the rare review article2,3 that devotes any space to multiphase diffusional phenomena. This is unfortunate, since the metallurgist frequently encounters practical situations involving cementation processes such as cladding, protective coating of metals, and so forth in which he needs guidance of a fundamental nature. The investigation of multiphase diffusion phenomena is complicated by the fact that one must consider reactions at phase interfaces as well as the migration of atoms within the individual phases; these reactions cause the interfaces to be displaced within the diffusion zone. The relative displacement of two adjacent interfaces corresponds to the growth of an intermetallic layer, and it is not difficult to determine experimentally the kinetics of layer growth. In the past few years it has been pointed out4,5 that valuable fundamental information may be gained about diffusion coefficients and the concentrations at interfaces through a study of their motion. Accordingly, it is the purpose of this paper to report the results of an investigation of interface motion in a simple multiphase binary system. In the work reported herein, attention was focussed on the growth of a 6 -brass layer in a diffusion couple prepared from a- and y-brass compositions saturated with respect to the 6 phase. This particular system was chosen for a number of reasons. First, the bcc ß-brass phase is disordered for all compositions at temperatures above 468°C and becomes increasingly long-range ordered for all compositions at temperatures below 454° C;6,7 thus, the effects of a variation in order on interface displacement could be determined. Second, diffusion coefficients have already been obtained as a function of temperature in the ß phase both in the ordered and disordered Re- and a theoretical picture of the mechanism of diffusion in this and other ordered solutions is emerging.11'12 Third, some thermodynamic data are available for the a-, ß-, and ?-brass phases,13,4 and these data could be used to gain insight into questions of phase equilibria and concentrations at phase interfaces.

Jan 1, 1963

By L. W. Kempf, R. S. Archer

The binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.' Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application. Constitution of Alloys Magnesium and silicon combine in aluminum alloys as the compound Mg2Si, which forms a binary system with aluminum. In alloys containing an excess of silicon over that required to form the compound, solidification ends with the freezing at 1022' F. (550' C.) of a ternary eutectic of aluminum, Mg²Si, and silicon. Judging from the horizontal projection of the liquidus surface as given by Hanson and Gayler,² this ternary eut,ectic contains about 13 per cent. silicon and 6 per cent. magnesium. All of the alloys discussed here contain excess silicon, so it

Jan 1, 1931

By A. B. Cox, L. W. Wark

In an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solution composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents—namely, sodium cyanide—on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electrolytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60". There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1935

By David C. Russell

The Department of the Interior used to be a quiet, noncontroversial, almost boring agency. It, after all is the fifth oldest of the Departments, and as an old line Federal agency it has studiously performed its preservation and resource management functions in a caretaker mode--though some would say more "undertaker" than "caretaker"--locking up the body and soul of America piece-by-piece. Yes, quiet, serene. That is until Jim Watt showed up. And we have all seen that version of Mt. Vesuvius which resulted--only it was the environmentalists who blew their tops. Ronald Reagan chose Jim Watt as Secretary of this fine old agency to prove that one-third of our Nation's land and over a billion acres on the Outer Continental Shelf can work for this Nation. At the foundation of President Reagan's charge to Secretary Watt is a belief in the tenets of the free enterprise system, and in the individual freedoms upon which this country was founded. There are those who don't share this belief in democracy and free enterprise, and those who believe this 205 year experiment called the United States of America will fail. Nikita Krushchev said "we will bury you"--obviously he didn't agree with our system. An Italian sociologist, Franco Ferrorotti, said bureaucratic stagnation will kill capitalism. Certainly we have all felt the ravages of bloated bureaucracies. Perhaps one indicator in the United States is the Federal Register, that daily compilation of Government's largesse. In 1970, 20,000 pages of the Federal Register were published. A decade later, in 1980, that volume had quadrupled to 80,000 pages. The Federal bureaucracy can stagnate from excessive budgets as well. The Interior Department spent $60 million on administering Federal coal leasing in 1981. That's nearly two bits a ton for every ton of coal leased in 1981. You wouldn't stay in business very long if your administrative overhead on inventory was that outrageous. But the pessimism of our critics is apparent from more than red tape and bloated budgets. For decades America has been fasting--consuming too little of America's wealth of minerals, subsisting instead on a diet heavily reliant upon mid-east oil, with little emphasis or concern for inventorying and developing domestic energy and mineral resources. Economics--yes. But short-term, short-sighted economics. Excessively dependent upon foreign imports, of oil, cobalt, chrome and other strategic minerals, the U.S. measures its time before another embargo--or fallen Shah, or Soviet manipulation, or Saudi shift, or, as we witnessed in Egypt, assassination--an untimely loss to mankind and efforts to bring peace to the troubled mid-east. These disruptions, in addition to their tragic human tolls, impair the free world's security. Huge chunks of the United States have been locked away in dozens of single land use categories in the name of conservation, with only the foggiest idea of what resources might be denied the American people-and this at a time of unacceptable levels of energy and strategic mineral imports. More than half and perhaps two-thirds of all Government-owned lands are totally withdrawn from or severely restricted to development under the mining and leasing laws. We must continue to rid Government of the overly zealous restraints which have been keeping us from drawing upon that which can help restore our economy and national security. When we assumed responsibility, the United States was dependent on foreign sources for about 40 percent of its oil. In 1981, our oil import bill was approximately $83 billion--nearly 17 times what it was in 1972. Our reliance on foreign sources for essential minerals is even more disturbing. We must look to other countries--some unfriendly, some unstable--for 22 of 36 strategically critical minerals. Yet the energy resources on federal lands which are owned by the American people could meet our needs for centuries if properly managed. Eighty-five percent of the crude oil yet to be discovered in America is likely to come from public lands, as will 40 percent of the natural gas, 35 percent of the coal, 80 percent of the oil shale, nearly all of the tar sands, and substantial portions of uranium and geothermal energy. Our vast hardrock-mineral wealth includes untapped deposits of essential elements we now import, such as chromium, copper, platinum, and cobalt. The obvious question is, if these abundant resources can help to revitalize our economic strength and to preserve our national security, why aren't we using them to better advantage? To a large extent, the answer can be found in past decisions to restrict public access to the federal estate, thus deferring to us or our successors the tough decisions that flow from Congress' mandate to provide for environmentally responsible development of America's energy and mineral treasures. Here is the legacy this Administration inherited: In January 1981, 7 years after the onset of the Mideast oil embargo: ---Less than 15 percent of federal onshore lands were under lease for oil and gas development; ---No oil and gas leases had been issued in Alaska for 15 years;

Jan 1, 1982

By P. Ramachandrarao, T. R. Anantharaman

CONSIDERABLE interest has lately been evinced as regards the nature of chill zones in solidified metals and alloys. Biloni and Chalmersl were the first to show through their study of segregation substructures in some nonferrous alloys that the formation of the dendritic region may be preceded by a diffusionless solidification process, viz., predendritic solidification. Subsequently Bower and Flemings2 tried a special solidification technique wherein the liquid was drawn into a narrow copper mold with polished surfaces and concluded that convection might trigger some multiplication mechanism leading to grain refinement. Using uncoated and partially coated surfaces for molds in the Bower-Flemings technique as well as in conventional molds, Biloni and Morando3 have very recently brought out the importance of the rate of heat extraction on the mechanism of solidification. We report here on the surface structures and substructures observed in a Sn-1 wt pct Pb alloy solidified at even higher cooling rates (riz., l05 to l07 ºc per sec) than those employed by earlier workers. The alloy was made by melting tin (99.99+ pct) and lead (99.9+ pct) in a silica tube under vacuum. Small quantities of the homogenized alloy (0.5 to 1.0 g) were then quenched (or splat-cooled) from the melt by the "gun technique" developed by Duwez et al.4 The thickness of the resultant foils varied from specimen to

Jan 1, 1970

By P. A. Vukmanic, M. Gensamer

Only recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Gossl stated that hot-rolled mild steel exhibits a texture different from that characteristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar 1/4 in. thick was hot-rolled at two temperatures, 780' and 910' C. (1436' and 1669' F.). These temperatures refer to the temperature of the furnace in which the steel was heated; after each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7' with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Mo target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780' C.), and that of the two

Jan 1, 1937

By O. N. Carlson, A. L. Eustice

The tensile properties of iodide vanadium were determined as a function of hydrogen concentration. It was shown that the presence of 10 ppm H is sufficient to cause embrittlement of vanadzum over a limited temperature range. The temperature of the observed ductility mininlum is approximately -l00°C, this being a function of strain rate and hydrogen concentration. The yield stress of hydrogenated vanadium is raised sharply in the brittle temperature range. THE present investigation was initiated to determine the effect of hydrogen on the tensile properties of high-purity vanadium as a function of temperature and the role of hydrogen in the brittle-ductile transition. Loomis and Carlson&apos; reported a change from ductile to brittle behavior in iodide vanadium at -110°C with a return of ductility at temperatures below -140°C. Vanadium wire containing 270 pprn of hydrogen was brittle at room temperature while wire containing 100 ppm was ductile under the same conditions. Roberts and Rogers&apos; reported a ductile-brittle-ductile fracture sequence in vanadium containing 400 to 600 ppm of hydrogen. Their data show that hydrogenated vanadium is ductile at 150"C, brittle at room temperature and ductile again at -196°C. Magnusson and Baldwin found a minimum in ductility in vanadium containing 80 ppm hydrogen from tensile tests performed at several strain rates. Information available on the vanadium-hydrogen equilibrium system4 is somewhat incomplete. The absorption of hydrogen is exothermic in accordance with the decline in solubility with rising temperature. The limit of solid solubility at temperatures below 400°C has not been determined due to the difficulties in obtaining equilibrium at these temperatures. Data on the hydrides of vanadium are rather limited. Roberts6 studied the structure of VD,., by neutron diffraction, and observed the ordering of the deuterium atoms below -65°C into a primitive cubic cell with a lattice constant about twice that of the disordered bcc vanadium solid solution. EXPERIMENTAL PROCEDURE Vanadium of 99.9 pct purity was prepared by the iodide refining process6 for use in this investigation. This vanadium contained the following analyzed impurities; <20 pprn calcium, 150 ppm carbon, 200 ppm chromium, 30 ppm copper, 10 ppm hydrogen, 200 ppm iron, <20 ppm magnesium, <20 ppm nickel, <5 ppm nitrogen, 150 ppm oxygen, <50 ppm silicon, and <20 ppm titanium. specimen Preparation—Tensile specimens were machined from swaged rods of iodide vanadium. The

Jan 1, 1962

By John Goheen

RECENTLY the head burner at a brick. plant with over 40 years&apos; experience said that he had burned brick by guess for over half his lifetime and had used pyrometers for 2 1/2 years but hoped that he would never have to burn kilns without pyrometers again. The ceramic engineer in making a special study of the burning of clay ware and the effect the heat of the kiln has on color and vitrification is also rapidly placing the burning of clay on a twentieth-century basis. Clay ware may be divided into various groups, brick and drain tile; sewer pipe; firebrick; and pottery, which, in turn may be subdivided into special classes. As nearly as the analysis of the clay type of kiln, etc., will allow, there are practically the same problems to solve in burning in all of the processes or operations. The underlying objective is the same, namely the production of the best grade of ware under the most efficient and economical manufacturing system. The principal problem in the production of clay ware is the burning off of the kilns. The most modern steam shovel may dig the clay and the most advanced types of pug mills and wire cut machines or molds of various kinds may be installed, but unless the drying and burning of the ware is successful, all of the previous operations will be useless. On this final operation depends the entire result of the plant. In reality, burning of all. clay ware is purely a heating proposition. The kilns, or furnaces, should be so designed as to give equal distribution of heat. Consequently, the problems of design and construction of kilns to produce equal distribution of heat require serious consideration, as do also the questions of heat control and draft control. The three most important factors in the burning of practically all types of kilns may be

Jan 9, 1919

By Richard L. Gordon

THE PROBLEMS AND POSSIBLE SOLUTIONS Toward the end of the 19th century, American industry began a drastic reorganization. The many, small, often-regional firms were supplanted by large national corporations-often produced by mergers among the existing firms. Giant companies appeared throughout American industry and many of them were engaged in the mineral industries.a The largest combines, by far, to emerge during the period were United States Steel and Standard Oil. Long before the restructuring had run its course, widespread concern arose over the process of concentration. Efforts were made to control, if not stop, the transformation. The concern produced the Sherman Antitrust Act of 1890 and the first of many federal regulatory agencies-the Interstate Commerce Commission (see Refs. 24, 31, 42). The basic objectives of these policies remain unclear to this day. The crucial issue is whether the goal is primarily to insure development of a more competitive economy or to preserve a social structure leaving more scope for small businesses. Complications arise from difficulties in agreeing upon the meaning of these terms. Studies of the early years of the antitrust movement suggest that it involved no particular concern over the mineral industries. Objections were directed at big companies in general. To be sure, the conservation movement arose in roughly the same period and did stress the evils of monopoly control of minerals. However, direct, continuing influence of conservation policy on antitrust is not apparent. Many of the most important antitrust cases, nevertheless, involved minerals. This, of course, may be sheer coincidence; the choice of cases has never followed any obvious pattern. Certainly, no simple hypothesis can explain the interest consistently. Once it may have been true that mineral industries were more likely than other sectors to be dominated by a few large companies. Yet, often sharp reversals of such tendencies -e.g., in oil and aluminum-have not removed antitrust interest. The importance of minerals to the economy cannot satisfactorily rationalize antitrust interest. The equally

Jan 1, 1976

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969

By Thomas A. Simpson, Russell A. Walker

Hydrogeological techniques were used to solve problems of slope stability in open-pit mines of the Eufaula bauxite district, Ala. Geologic and hydrologic data were evaluated and used to design a system of dewatering wells to enable the operators to mine bauxite more efficiently and economically. Walls of open-pit mines in the district were subsequently stabilized by the operation of the dewatering system. Three open- pit mines, each at varying stages of the mining process, of the A.P. Green Refractories Co., were used to develop a sequential series of guidelines that indicate how to effectively remove ground water from the formations surrounding the ore bodies in the district. The use of sound engineering principles in well design, in combination with the correct interpretation of the pit hydrology provided the basis for solutions of the slope-stabilization problem and aided in the economical removal of bauxite from mines of the district.

Jan 1, 1976

By John M. Dale

Sulfur has attractive features as a base material for coating systems. It melts at 246ºF and can be applied as a liquid above this temperature. Its melting point is just above the environmental stress level, 180°F, for most coatings and yet it is low enough to be easy to work with in comparison to many hot melt systems. The viscosity characteristics are such that sulfur lends itself to spray applications. The oxidation rate of sulfur in the atmosphere is very low and sulfur has outstanding chemical resistance characteristics, particularly in acid environments. One of the greatest potentials for these coatings appears to be in the protection of other materials. At one time, most acid tanks and pits were constructed with acid- proof brick and sulfur based mortars. This type of construction is much more expensive than sulfur based spray coatings. An attractive sulfur based coating composed of sulfur, talc, milled glass fibers and dicyclopentadiene,1 developed by the Institute for the Bureau of Mines has excellent acid assistance and can be used to protect concrete from acid attack.

Jan 10, 1973

By Rajaraman V. Ramani, K. Sinha Atmesh, Robert Stefanko

Use of electrical power in the bituminous mining industry has increased many fold during the last few decades. Rapid changes have also occurred in mine electrical power systems in order to meet the demands from highly mechanized mines. Fires, explosions, and deaths due to electrocutions are the primary hazards due to the underground use of electricity, although there has been a marked decrease in the fatality rate from electrical accidents. However, efforts to eliminate electrical hazards and to insure trained manpower for better distribution, utilization, and protection of the electrical systems cannot be relaxed. In this article, 200 fatal accidents that occurred during the period from 1955 to 1970 have been analyzed. Accident frequency has been correlated with the size of the mine and of the work force, and with age and work and task experience. A strong negative correlation has been established between task experience and accident frequency. Though the available data permitted only a limited analysis, need for improvements in electrical power technology and for better education and training has been identified and discussed. Missing information in accident statistics is outlined and suggestions for better hazard analysis are presented.

Jan 1, 1975

By J. C. Williams

THE operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent-namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components-that is, the silica, alumina, iron and lime-and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1946

By D. O. Ehrenburg

DURING the earlier period of electrical prospecting, the search for orebodies was by far the most important application of this method of geophysical prospecting. In the past few years, however, increasing attention has been paid to the possibilities of this method in the investigation of subsurface structures. Not only have fault zones been located, but attempts have been made to determine the depth to certain strata and thus contouring on some bed which proves to be a good "electrical marker." Many workers have published the results of field tests showing how their particular interpretations have agreed with the actual field conditions, but very few have stated their method of interpretation. Weaver, Hummel and Stefanesco and Schlumberger1 have given a more theoretical discussion of the resistivity methods. Hummel and Stefanesco and Schlumberger have published mathematical solutions for the flow of electricity in a medium involving four layers. In this paper the authors present a solution for the flow of electricity in a medium of any number of horizontal strata. By means of this solution, curves showing the relationship between the apparent resistivity and the electrode spacing can be computed for ideal cases.

Jan 1, 1931

HAVING produced one ton of concentrate that contains the copper that can profitably be saved or recovered from anywhere between 3 and 60 tons of mine ore, the ore-dressing engineer passes the result of his handiwork over to the metallurgist for smelting. Essentially, the concentrate is a damp mass of finely ground material consisting of copper sulphide minerals; pyrite, the sulphide of iron; and gangue, usually silica and silicates of aluminum. The purpose of smelting is to produce metallic copper and a slag containing the iron and siliceous constituents by pyrometallurgy-the kind of metallurgy that employs fire and heat to produce the chemical reactions through which it attains its object. Though blast furnaces have been used to smelt Porphyry-mine concentrates, notably at Braden, more than 90 per cent of [ ]

Jan 1, 1933

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

By AIME

In Emporia or Claremore, time was when a path was beaten to the door of the local sage. Nowadays, the beginnings of such a path are discernible in Tennessee, as folks of the metallurgical persuasion find it to their pleasure and profit to call upon the Sage of Copperhill. They come, more and more respectfully as the years go by, yet to ever fewer persons is he known as Mr. Myers, but to more, eloquently, as Jack. Find better ways to run your mill, find happier means of co-ordinating your humanities or serving your professional society, and it&apos;s just like the man said about the mousetrap. A druggist&apos;s son, born in Wisconsin, May 24, 1889, reared on the Bible in Ohio and Indiana, and completing his education in Colorado, this now indisputably 24-carat Tennesseean has had a checkered career. Going West as a laborer at the tail end of the 1907 panic, he did not make his fortune but he did gain an understanding of labor that in later years endeared him to his men. Graduating in 1913 from Colorado School of Mines with the degree of E. Met. and a string of football letters (also earned the hard way, at tackle) he went to work in Butte & Superior, just at the beginning of the Golden Age of flotation.

Jan 1, 1949

By J. E. Graham, A. H. Glenn

Oil operators engaged in drilling on the Continental Shelf of Louisiana and Texas are in agreement that adverse weather and wave action are two of the greatest hazards to the safety and efficiency of their work. It was ami-pated when the offshore operations commenced that such would be the case, and experience to date has verified this assumption. Because atmospheric conditions and wave action involve tremendous amounts of energy it is highly unlikely that it will be possible to control any but the most localized weather and wave phenomena within the foreseeable future. Thus. as long as the offshore operations involve the movement of small craft and barges over exposed waters, and the transfer of personnel and heavy equipment from these craft to either fixed structures or larger craft at close quarters, the weather and wave problem will remain. Taking into consideration the persistence of the wave and weather problem and the improbability of achieving a direct solution, the Humble Oil & Refining Company, in planning its offshore campaign investigated the possibility of forecasting wave and weather conditions in order to provide warnings of dangerous conditions and increase efficiency in day-to-day planning of work. It was recognized that predictions of wave and weather conditions based on meteorology and oceanography, both geophysical sciences, are not 100 per cent accurate and application of forecasts in the offshore work was dependent on whether they provided information which was sufficiently greater in accuracy than the layman&apos;s guess to be worth the expenditure involved. During World War 11. meteorology and oceanography were used with success in reducing danger resulting from environmental conditions and increasing efficiency of operations exposed to the elements. This success was partially the result. of improvement in the scientific techniques involved and the procurement and distribution of observational data, and partially due to the large scope of the military operations which meant that a reduction of losses of a relatively small percentage of the total cost amounted to a large figure expressed in terms of dollars. Since the offshore drilling involves an extremely large financial investment, it was considered that the experience of the Armed Services in successfully employing meteorology and oceanography might be duplicated in the oil industry. In addition. the oil industry&apos;s successful experience in utilizing seismology, geology, and terrestrial magnetism; all geophysical sciences, indicated that meteorology and oceanography, also of the family of geophysical sciences and sharing their scientific assets and liabilities, might be profitably put to use. Since the immediate problem involving the sciences of meteorology and oceanography in the offshore campaign is wave action, a program was inaugurated within the Humble Oil & Refining Company during June 1947. the purpose of which was to ascertain the applicability and limitations of wave forecasting in the offshore campaign. A summary of the effective wave forecasting techniques developed during the war was prepared in the form of a forecasting manual for the Continental Shelf off Grand Isle, Louisiana, by Bates and Glenn. After completion of this manual, experimental forecasts were prepared daily over a two-month period by Graham and Thompson to determine the accuracy of the forecasts. It was considered that the accuracy of the experimental forecasts justified a more extensive test under actual operating conditions in the offshore work and the firm of A. H. Glenn and Associates was set up under the sponsorship of the Humble Oil & Refining Company to work with the Humble Grand Isle District in providing forecasts of wave and weather conditions over a one-year period. This paper discusses the service now provided to the Grand Isle District, its applicability and limitations. TYPE OF FORECASTS REQUIRED It was apparent before the commence-mence of the forecasting service that a specialized type of forecast was required. Many of the weather elements of interest to the general public, such as rain and temperature, are of minor concern to offshore operators. On the other hand, such elements as wave height and wind speed and direction are of great concern in the offshore operations since variations in wave height of a few feet in the critical range divide safe from hazardous working conditions. To be of utility. a forecasting service for the offshore work must provide detailed forecasts of the elements which affect the operation. With this in mind, it was decided that forecasts would include the following information: average wave heights to the nearest foot, wind speeds within a range of approximately 5 miles per hour, and wind directions within 221 degrees. Since the procedure for forecasting these elements involves thorough analysis of weather data, it was decided to include a generalized forecast of weather conditions such as rain and cloud cover, although these are of secondary importance.

Jan 1, 1949

By A. H. Glenn, J. E. Graham

Oil operators engaged in drilling on the Continental Shelf of Louisiana and Texas are in agreement that adverse weather and wave action are two of the greatest hazards to the safety and efficiency of their work. It was ami-pated when the offshore operations commenced that such would be the case, and experience to date has verified this assumption. Because atmospheric conditions and wave action involve tremendous amounts of energy it is highly unlikely that it will be possible to control any but the most localized weather and wave phenomena within the foreseeable future. Thus. as long as the offshore operations involve the movement of small craft and barges over exposed waters, and the transfer of personnel and heavy equipment from these craft to either fixed structures or larger craft at close quarters, the weather and wave problem will remain. Taking into consideration the persistence of the wave and weather problem and the improbability of achieving a direct solution, the Humble Oil & Refining Company, in planning its offshore campaign investigated the possibility of forecasting wave and weather conditions in order to provide warnings of dangerous conditions and increase efficiency in day-to-day planning of work. It was recognized that predictions of wave and weather conditions based on meteorology and oceanography, both geophysical sciences, are not 100 per cent accurate and application of forecasts in the offshore work was dependent on whether they provided information which was sufficiently greater in accuracy than the layman&apos;s guess to be worth the expenditure involved. During World War 11. meteorology and oceanography were used with success in reducing danger resulting from environmental conditions and increasing efficiency of operations exposed to the elements. This success was partially the result. of improvement in the scientific techniques involved and the procurement and distribution of observational data, and partially due to the large scope of the military operations which meant that a reduction of losses of a relatively small percentage of the total cost amounted to a large figure expressed in terms of dollars. Since the offshore drilling involves an extremely large financial investment, it was considered that the experience of the Armed Services in successfully employing meteorology and oceanography might be duplicated in the oil industry. In addition. the oil industry&apos;s successful experience in utilizing seismology, geology, and terrestrial magnetism; all geophysical sciences, indicated that meteorology and oceanography, also of the family of geophysical sciences and sharing their scientific assets and liabilities, might be profitably put to use. Since the immediate problem involving the sciences of meteorology and oceanography in the offshore campaign is wave action, a program was inaugurated within the Humble Oil & Refining Company during June 1947. the purpose of which was to ascertain the applicability and limitations of wave forecasting in the offshore campaign. A summary of the effective wave forecasting techniques developed during the war was prepared in the form of a forecasting manual for the Continental Shelf off Grand Isle, Louisiana, by Bates and Glenn. After completion of this manual, experimental forecasts were prepared daily over a two-month period by Graham and Thompson to determine the accuracy of the forecasts. It was considered that the accuracy of the experimental forecasts justified a more extensive test under actual operating conditions in the offshore work and the firm of A. H. Glenn and Associates was set up under the sponsorship of the Humble Oil & Refining Company to work with the Humble Grand Isle District in providing forecasts of wave and weather conditions over a one-year period. This paper discusses the service now provided to the Grand Isle District, its applicability and limitations. TYPE OF FORECASTS REQUIRED It was apparent before the commence-mence of the forecasting service that a specialized type of forecast was required. Many of the weather elements of interest to the general public, such as rain and temperature, are of minor concern to offshore operators. On the other hand, such elements as wave height and wind speed and direction are of great concern in the offshore operations since variations in wave height of a few feet in the critical range divide safe from hazardous working conditions. To be of utility. a forecasting service for the offshore work must provide detailed forecasts of the elements which affect the operation. With this in mind, it was decided that forecasts would include the following information: average wave heights to the nearest foot, wind speeds within a range of approximately 5 miles per hour, and wind directions within 221 degrees. Since the procedure for forecasting these elements involves thorough analysis of weather data, it was decided to include a generalized forecast of weather conditions such as rain and cloud cover, although these are of secondary importance.

Jan 1, 1949