Search Documents

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965

By A. Styka, G. Fischer, S. Tour

Described herein are the results obtained during research work involving coating titanium alloys with molybdenum by vapor-deposition methods. Results show that the method can be used successfully to deposit hard adherent wear-resistant coating of methodmetallic molybdenum on titanium or titanium alloys without changing the microstructure of the titanium base. PRODUCTION and use of titanium and its alloys have increased tremendously in the past few years. The physical, mechanical, and chemical properties of this engineering metal have caused considerable enthusiasm among metallurgists and engineers. However, as with all materials, there are some drawbacks. For example, titanium is susceptible to seizing and galling on wearing surfaces. In order to produce a good wear-resistant surface, many investigations have been conducted evaluating oxidizing, carburizing, nitriding, carbonitriding, sili-conizing, and chromizing of titanium. All of these processes require high temperatures for rather extensive periods of time. It has been possible to produce hard surfaces on titanium and its alloys by a number of these processes at the expense of a deterioration of the physical properties of the base material. A practical solution to the problem of providing titanium and titanium alloy parts with a satisfactory wear-resistant nongalling surface must be one that does not involve excessive temperatures for long periods of time. Sam Tour & Co. Inc. has completed a research and development contract for the United States Army Ordnance Corps on vapor deposition of molybdenum on titanium and titanium alloys. On the basis of results obtained from the research program, titanium alloys can be coated successfully with molybdenum to provide a hard wear-resistant surface without harm to their base mechanical properties. The remainder of this article is a description of the techniques used to apply the coating and the results obtained from wear tests on molybdenum-coated titanium. Theory Basically, the technique used was the application of molybdenum by a vapor-deposition method, thermal decomposition of molybdenum hexacarbonyl [Mo(CO)] with hydrogen as the carrier gas. The selection of this method was based chiefly on the following considerations: 1—low plating temperature which would minimize excessive grain growth, 2— low decomposition temperature of the carbonyl, 3— possibilities of controlling the hardness of the plate by adjusting the carbon content using the plating temperature and pressure as the primary variables, 4—use of high vacuum, thereby avoiding unnecessary oxidation and other complex reactions with the atmosphere. Free energy data1 show the strong tendency for titanium to combine with O2 N2 or carbon from normal temperatures to temperatures above its melting point. To maintain the titanium in a film free condition, the use of as high a vacuum as possible is indicated. The literature' indicates that the reaction product of hydrogen with titanium is unstable in vacuum at around 400°C. 5—Although it is indicated from the thermodynamic standpoint that there is little possibility of removing carbon from either titanium or molybdenum, the work of Lander and Germer -ndicates that the use of a suitable H,/CO ratio is somewhat effective in minimizing carbon deposition. 6—Availability of molybdenum carbonyl. In the simplest form, the conditions of equilibrium3 in chemical reactions involving decomposition of carbonyl are as follows: Mo (CO) ? Mo + 6CO 2CO * C + CO,. The plating rate is proportional to the rate of evolution of CO from the decomposed carbonyl, i.e., it is proportional to the pressure of the gaseous decomposition products. Carbon released from CO gas is the significant constituent for the variability of the physical properties of the product. High carbon deposition is favored by increasing pressure. Limitations are imposed in the selection of plating temperature and pressure. Excessive temperature re-

Jan 1, 1956

By M. J. Marcinkowski, D. Koskimaki, A. S. Sastri

THIS is the second in a trilogy of investigations carried out in order to understand the solid state transformations and their accompanying effects on the deformation behavior of near-equiatomic Ni-Ti alloys. The first stage of this effort has dealt with the strictly martensitic structures obtainable in these alloys, i.e., those in which diffusion processes were not involved.1,2 These martensites could be produced either by rapid quenching or by plastic deformation of the originally B2 type phase. The present investigation, on the other hand, will deal with those transformations in Ni-Ti which do involve diffusion. A majority of investigators3-10 have shown that the B2 modification of TiNi, which is stable at elevated temperatures, decomposes into one or both of the intermetallic compounds NiTi2 and Ni3Ti below about 650°C. On the other hand, this has been disputed by several Workers was undertaken in order to resolve this discrepancy, as well as to shed more light on the nonmar-tensitic decomposition of B2 NiTi. EXPERIMENTAL PROCEDURE Sample preparation, fabrication, and examination were the same as those described previously in Ref. 2. In addition to the 50 at. pct Ni (55.06 wt pct) hypoeu-tectoid alloy used previously, a second hypereutectoid alloy containing 54.4 at. pct Ni (60 wt pct) was also prepared for this study. RESULTS AND DISCUSSION The equilibrium diagram for the Ni-Ti alloy system in the vicinity of Ni-Ti is shown in Fig. 1. The solid lines have been established by the work of Poole and ~ume-Ftothery4 whereas the dotted lines are based on findings obtained in the present investigation as described below. Structure and Morphology. Fig. 2(a) shows a bright field transmission electron micrograph of a two-phase structure obtained in a polycrystalline Ni-Ti alloy that was furnace cooled (approx 200°C per hr) from 1050' to about 300°C. Large plate-shaped precipitates can be observed in a matrix which was found by electron diffraction to possess the high temperature B2 structure. A selected area diffraction pattern of the region covered by Fig. 2(a) is shown in Fig. 2(b), while Fig. 2(c) is a detailed schematic interpretation of Fig. 2(b). The B2 matrix reflections are illustrated by squares while those of the precipitate are shown as circles. The d values associated with the precipitate reflections could be determined quite accurately since the reflections from the B2 matrix, for which the lattice constant is known precisely, were simultaneously present in the diffraction patterns. All of the reflections

Jan 1, 1970

By L. K. Oliver, Marshall

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Marshall, L. K. Oliver

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952

By D. A. Dahlstrom

Although the liquid-solid cyclone is a relatively recent innovation in the field of coal preparation, various authors have already indicated three distinct applications to operations encountered in the modern tipple. Driessen's articles and work at the Dutch State Mines exhibited its possibilities in the bene-ficiation of fine coal with apparently high efficiencies down to the 200-mesh fraction. l,2,3,4 Other publications point out its use as a recoverer, thickener, and preliminary dewatering agent of fine coal which in too many cases is being wasted due largely to former high operating cost limitations.M Finally, certain authors have emphasized the practicability of applying the cyclone to the elimination of coarse and fine solids from water slurries in the tipple in order to produce a water suitable for recycle purposes containing only minute particles far below the 200-mesh size.6 This would result in a closed water system for many cases, with its accompanying economic and operating advantages to locations where water quantity and quality problems are severe; better operation of washing equipment using a consistent water devoid of injurious fine particles; lowered maintenance costs due to the lesser abrasion resulting when the fine abraiding particles are removed; and the greater ease of disposing of refuse streams of reduced volume containing greater percentages of solids. While the three applications have been indicated to be feasible, only a meager amount of data is available on capacities and solid elimination eficiency as a function of design variables and cyclone friction loss. This information is essential for the optimum use and construction of the solid-liquid cyclone, and accordingly, work on the problem was initiated at Northwestern University. For the unfamiliar reader, briefly the cyclone consists of a cylindrical section mounted above a truncated cone. The feed nozzle enters the cylindrical ring tangentially with the underflow nozzle permitting discharge of the concentrated solids located at the apex of the cone. The overflow nozzle through which the clarified water exits is centered in the cylindrical section at the top of the cyclone. Half sections of experimental cyclones will be found in Fig la and 6. The feed slurry enters with a tangential velocity, thus creating a spiral pattern of high centrifugal force. The solid particles of sufficient size and gravity are ejected outward to the walls and spirally discharge to the underflow. Most of the water with uneliminated fine solids moves radially inward along the path of the outer

Jan 1, 1950

By Samuel L. Hoyt

THE present report represents that part of the work that has been done by the War Minerals Investigation, Manganese Section, of the Bureau of Mines, on the use of manganese alloys in open-hearth practice. The magnitude of the work and the number of people participating in one way or another make it difficult to acknowledge adequately the services of all who have contributed to the success of the work. It would, be amiss, however, to pass to the body of the report without mentioning the hearty coöperation and willingness to assist of the various manufacturing interests. With such a sympathetic attitude toward this investigation, our work was assured of success. Inasmuch as the unhappy circumstances that rendered this investigation necessary have now passed, this report is made in 'the hope that the results may prove of some permanent value to the peace-tine operation of our open-hearth industry. Broadly speaking, the purpose of the manganese investigation was to consider the most suitable means of utilizing our domestic supply of manganese and thus relieve, to the maximum extent possible, our shipping of the burden of importing manganese ores. It was not held that any decided shortage of manganese 'was imminent but rather that every legitimate means should be utilized for making our ship tonnage available to European service. While we have considerable metallic manganese in this country, it occurs largely as a low-grade mixture with iron or silica or with both. The open-hearth investigations, therefore, were carried on to determine the extent to which domestic or low-grade alloys could properly be substituted for high-grade alloys without materially impairing the steel production as to either quality or quantity. Also, it was held that such an investigation would yield valuable results to the steel industry as well as contribute, in no small way, toward

Jan 2, 1919

By B. Hyatt, E. Klokholm

The reesistivity of Cu-Pd alloys of 9.6 to 29 pct Pd alloys was measured after plastic deformzation in tension. For all compositions a continzting decrease in resistivity with increasing plastic strain was observed. By comparison with the results of Damask on a brass ad Cu3Au, it was deduced that these anonzalous decreases in resistivity are due to the decrease in short-vunge order caused by cold work. An anomalous decrease in the resistivity of cold-worked CU-Pd alloys was first reported by Jaumot and Sawatzky.' They observed decreases in the electrical resistivity when disordered Cu-Pd alloys drawing at room temperature. Recently, a similar anomaly was reported by Aarts and Houston-Mac-Mi1lan2 in Ag-Pd alloys containing 10 to 45 pct Pd. The plastic deformation in this case was produced by tensile strain at liquid-nitrogen temperatures. For AE-Pd alloys the relative resistivity change becomes positive for tensile strains of about 20 pct.

Jan 1, 1960

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965

By J. H. M. Thomeer

A method is presented that provides a mathematical description of capillary pressure curves and, probably, of differences in pore geometry of samples. The technique is based on the observation that the location and shape of a capillary pressure curve reflect characteristics of the pore structure of the sample. INTRODUCTION It has been noted1-5 that the observed differences in shape and location of capillary pressure curves reflect some basic properties regarding the pore geometry of the samples. For example, according to basic concepts of capillarity, the following statements can be made regarding the location and shape of a capillary pressure curve.* The location of the curve with respect to the (Vb)pc and PC axes is a measure of the interconnected pore volume and of the cross-sectional area of the pore first entered by mercury, respectively. The shape of the curve depends on the interconnection of the pores and the sorting of the pore sizes. It has been the object of this study to use this information as a starting point in an attempt to find a unique mathematical description of the PC — (Vv)p, relations of different samples. It may be expected that parameters in such a relation can then be used to describe differences in pore geometry of these samples. For a practical description of the PC — (Vb)p, relation, however, it appears desirable to describe each curve (i.e., each sample) by a limited number of parameters so that the curves taken from all samples form a family, each member of which is uniquely determined by one single combination of values of all parameters.

By George Rice

A PROBLEM of possible subsidence of the surface from mining opera-tions, which might have had disastrous results, arose in 1913 at the Brier Hill mine, of the Penn Iron Mining Co., near Norway, Mich., now managed by Pickands, Mather & Co. for the Bethlehem Steel Co. A double track and sidings of the Chicago & North Western Railroad passed over part of the mine, and if subsidence had reached the surface it might have affected the stability of the tracks. The chief purpose of this paper is to record the facts disclosed by investigations of underground movement from 1913 to 1919, when the tracks were moved, and subsequently at intervals, as engineering data of value from mining carried on below the tracks in the steeply pitch-ing lenses. A secondary purpose of this paper is to describe a novel method for determining the rate of speed of upward breaking above the mine excava-tions. This method was found effective and might be used elsewhere under similar conditions. The mine workings under consideration were developed from the Brier Hill shaft, which was circular, concrete-lined, 14 ft. in diameter, and about 900 ft. deep. They extended about 800 ft. westward from the shaft, and nearly parallel to a corresponding length of the railroad tracks. The highest part of these workings was at a depth of 400 ft. below the tracks (Figs. 1-12). The mining company had the right to remove the ore, the railroad assuming that the surface would be sup-ported. Finally, without legal controversy, an amicable adjustment was reached as to what should be done to lessen or obviate the hazard of subsidence.

Jan 1, 1934

By D. A. Koss, R. O. Gordon

Changes in the ultrasonic attenuation in steel specimens have been observed during tensile tests. Samples of AISI 1020, 1045, and 1095 steel quenched and tempered to a spheroidized condition have been used. Both attenuation and microstrain measurements fail to reveal preyield dislocation motion in the as-tempered specimens. Upon reapplication of the load to samples in the strain-aged condition there is a large preyield attenuation increase but no observable micvostrain up to 90 pct of the flow stress. These and other observed changes can be related to changes in the free disloca-tion density and the average dislocation segment length. The results show that the increase inflow stress in the strain-aged condition is caused by increased fric-tional stresses rather than by dislocation pinning. Strain aging is found to proceed through three distinct stages. The second of these follows the t2,3 law and is characterized by an activation energy of 20 kcal per mole. RECENT years have seen substantial progress in the understanding of the sharp yield-point phenomenon in metals; the influence of solute atom pinning of dislocations, of dislocation multiplication, and of the stress dependence of dislocation velocity on the stress-strain curve has been investigated. Evaluation of the relative importance of these factors in the various metals and alloys is not complete, however, because observation of the stress-strain curve alone is not sufficient to determine the yield mechanism. In the experimental study of the sharp yield point it would be desirable to be able to directly observe the dislocations in a bulk specimen. Ideally, the observations should be made during deformation because of the rapidity of recovery processes in lightly strained metals. While direct observation of dislocations under these conditions is not possible, certain physical properties sensitive to the dislocation structure can be observed while a test specimen is undergoing deformation. Of these properties, one of the most useful is the ultrasonic attenuation. The total observed attenuation, a, is due to a number of causes: acoustic diffraction, scattering by inhomogeneities in the structure, heat flow, magnetostriction, and dislocation damping. Satisfactory measurements of the absolute a are difficult to make because all of these factors cannot be evaluated in any given specimen, but changes in a due to changes in the dislocation contribution alone can be reliably observed by appropriate technique. Because dislocation damping is sensitive to small concentrations of long, free dislocation segments, observation of acoustic attenuation due to dislocations is particularly useful in the study of the early stages of plastic deformation. In the experiments to be described, acoustic-attenuation measurements have been made on steel samples as these were pulled through their yield in tension. While many details of dislocation-damping phenomena in the bee metals remain obscure, the main characteristics of this type of internal friction are established. At low strain amplitudes and at frequencies well below that of dislocation resonance (the conditions of these experiments) the dislocation contribution to a is given by1 where A is the density of freely oscillating dislocation segments, L is the average segment length, B is the damping constant for a moving dislocation, w is the frequency, O is an orientation factor, C is the dislocation line tension, and t is a numerical factor relating average segment length to the distribution of lengths. Because of its fourth-power dependence on L, a is highly sensitive to changes in dislocation free segment length such as might arise from unpinning, recovery, jog formation, or dislocation intersection. The above equation is not valid near the resonant frequency of dislocations, but the segment length in steel is believed to be much too short to cause over-damped resonance near 10 Mc; this will be discussed later. In the present experiments plastic-strain measurements with a sensitivity of 2 x 10-5 were also made during the early stages of loading in order to detect preyield strain. The general plan of the experiments is to observe

Jan 1, 1967

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Samuel Daniels

Aluminum-base alloys containing small amounts of copper and magnesium possess but ordinary physical properties as sand cast, but may be treated to give a remarkable range of tensile values and of Brinell hardness. The high-copper (4.5 per cent.) duralumins must be given a protracted treatment which in nature resembles the malleableizing of white cast iron; the low-copper (2.25 per cent.) duralumins develop an excellent combination of strength and ductility with a treatment which requires a maximum of 5 hr. to be completed. THE wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating to 932° F. (500° C.) for 2 hr., cooling in, air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that " considerable improvement in the mechanical properties of copper-aluminum alloys' may be obtained from suitable heat treatment applied to castings."2 Jeffries and Gibson3 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932° F. in a

Jan 7, 1924

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

The dictionary defines 'jargon' as "barbarous or debased language ". This description does not suffice. Quiller-Couch has said, it is "a kind of writing which, from a superficial likeness, commonly passes for prose in these days, and by lazy folk is commonly written for prose, yet actually is not prose at all ". The two main vices of jargon, he says, are "that it uses circumlocution rather than short straight speech", like the Babu who reported his mother's death by saying: "Regret to inform you, the hand that rocked the cradle has kicked the bucket ". Its other chief vice is that "it habitually chooses vague woolly abstract nouns rather than concrete ones", like the newspaper statement, "He was conveyed to his place of residence in an intoxicated condition", instead of saying, "He was carried home drunk". Jargon is "an infirmity of speech", it is not journalese, but akin to it. "Like respect- ability in Chicago, jargon stalks unchecked in our midst" and renders much technical writing ridiculous. It deals in periphrasis instead of going straight to the point, it loves the abstract rather than the concrete, it dabbles in words of sound rather than of meaning. Avoid it, despise it, if you purpose earnestly to write well. "In literature as in life he makes himself felt who not only calls a spade a spade but has the pluck to double spades and redouble." * Jargon is rampant in technical publications. Catalogues and other advertisements are conspicuous offenders, but with these the critic is not concerned, except in so far as such 'write-

Jan 1, 1931

By J. S. Browning

The U.S. Bureau of Mines has been experimenting with flotation processes to separate the spodumene-beryl ores mined at Kings Mountain, N.C. The success to date as well as the present status of the process is discussed. Further experimentation is underway and studies will be made on the milling costs involved in the flotation process. The pegmatites of the Kings Mountain-Lincoln ton, N.C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li,O(lithia) as spodurnene.' The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,-000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2-7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals. Several years ago, the U.S. Bureau of Mines, recognizing the need for developing a large domestic supply of strategic beryl, undertook studies to develop improved methods of recovering this mineral. Because of the low beryl content of the pegmatites, economic production of the beryl entails its recovery as a byproduct of spodumene flotation. Thus, the development of procedures that would provide for maximum recoveries of the spodumene, as well as the beryl, was a primary objective of the studies. Tests were made on run-of-mine ore and spodumene flotation tailing from the Foote Mineral Co.'s spodumene concentrator at Kings Mountain (Fig. 1). Pet-rographic analyses of the ore and flotation tailing are given in Table I. Detailed analyses and examinations of the ore and tailings revealed that the beryllium was present in the form of a low-alkali beryl. The crystals were small, rarely larger than 14-mesh diam, and were clear and colorless. About 10 pct of the Li20 content of the ore was present in the mica and feldspar components of the pegmatite. In some weathered ores the associated clays also contained small amounts of lithia. This is typical of pegmatites in the Kings Mountain area. LABORATORY TESTS In the past, a vigorous chemical treatment of the spodumene surfaces with acid or caustic soda has been considered essential for satisfactory selective flotation of the spodumene from the other minerals in pegmatites. Many tests were made during this investigation to determine if chemical treatment of the spodumene could be eliminated in favor of a reagent combination that would depress the other minerals while selectively floating the spodumene. A simple reagent combination and process was developed that gave better spodumene recovery and grade of concentrate than the more elaborate acid or caustic treatment methods previously used. The finely ground ore pulps were conditioned with either an ammonium, alkali, or alkaline earth lignin sulfonate and sodium fluoride, and the spodumene was floated and cleaned using oleic acid as the collector. The spodumene tailing was deslimed, conditioned with sulfuric acid and coco amine acetate, and floated to reject mica. The mica tailing was thickened and conditioned with hydrofluoric acid, then washed to remove the acid. The washed pulp was conditioned with sodium hydroxide for pH control, and the beryl was floated and cleaned with oleic acid as the collector. Table II summarizes the results of the laboratory test work. About 77 pct of the spodumene and 75 pct of the beryl were recovered from the pegmatitic material. The spodumene concentrate assayed 6.1 pct Li20 and 0.01 pct BeO, and the beryl product assayed 3.0 pct Li20 and 1.57 pct BeO. Similar results were ob-

Jan 1, 1961