Search Documents

By L. C. Uren, E. J. Bradshaw

This paper presents the results of a group effort by a number of University of California students and faculty members, and the authors attach their names primarily in the capacity of editors and interpreters of the data thus assembled. In addition to the writers, the following individuals have made substantial contributions in time and effort in the conduct of this research: Dr. A. J. Carlson, Associate Professor of Petroleum Engineering; J. E. Gosline, University Research Assistant; C. F. Bedford, G. W. Mikulasek and H. S. Conder, senior and graduate petroleum engineering students; H. Bachman, G. Spencer and G. W. Gard, mechanicians in the Department of Mining and Metallurgy. Acknowledgment is also due the Research Board of the University, the Department of Mining and Metallurgy, and Prof. F. H. Probert, Dean of the College of Mining, for continued cooperation in securing mechanical assistance and funds for the purchase and assembly of apparatus. Significance of the Pressure Gradient The expulsion of petroleum from its reservoir sand doubtless is due to expanding natural gas intimately associated with the oil, to the hydrostatic pressure of encroaching edge waters, and to gravitational influences. These forces may operate independently or collectively. In any case they subject the fluids stored within the reservoir sands to elevated pressures, thus causing movement of oil and gas through the productive formations toward the lower pressure of the well outlets. This movement is opposed by pore friction, capillarity and adhesion: resisting influences brought to bear by the reservoir sand on the moving fluids. The magnitude of the resisting force is influenced directly by the viscosity, surface tension and density of the oil, as well as by the properties of the gas. The more rapid the rate of flow, the greater will be the resistance offered, and the greater will be the energy consumed.

Jan 1, 1932

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objection- able to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for efficient hand picking. At most mines an attempt is made to remove the visual impurities at one or more of the following places in the surface plant? (1) in the tipple during screening; (a) on picking band, belt, or shaking conveyors;*(3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller

Jan 1, 1943

By C. A. Heiland

I. Description of reflection equipments.................. 412 A. Design features of present types.................. 412 B. Reflection equipment designed by writer.............. 418 11. Characteristics of reflection seismographs............... 421 A. Types of coupling in electromagnetic seismographs.......... 421 B. Action of pickup, amplifier and galvanometer............. 424 C. Combined action of pickups, amplifiers and oscillographs....... 433 D. Static and dynamic constants................... 434 E. Desirable values for static and dynamic constants.......... 435 111. Calibration of reflection apparatus.................. 442 A. Dynamic tests without shaking table................ 442 B. Calibration methods....................... 445 C. Various other tests........................ 451 INTRODUCTION In the past five years, the reflection method of seismic prospecting has been developed to a high degree of perfection. Its success in mapping oil structure is due to the unique and definite nature of the depth data obtained. While articles on the principle and results of this method continue to appear in increasing number, there is virtually nothing published about the instruments used in this work. Several years ago, the writer started an experimental and theoretical investigation with the object of determining which characteristics would be best adapted to the problem at hand. As a result, an equipment was developed which has proved its usefulness in a great number of field tests. W. E. Pugh, now with the Empire Oil and Refining Co., joined the writer, in 1931 and 1932, in the laboratory experiments and field tests. In 1933, a paper was written on Certain Instrument and Field Problems in Reflection Seismology, and submitted to the Institute. The part of that paper dealing with field tests was published as Contribution 34 (reprinted in this volume, p. 455). Since then, considerably more labora-

Jan 1, 1934

By D. W. Fuerstenau

A detailed study of the residence time distribution in an industrial balling circuit is presented. Using fired recycle pellets as a tracer impulse in each experiment, material was found to pass through the drum under plug flow conditions with a mean residence time of about 20 seconds. The time for a single pass through the entire circuit is about 60 seconds. Approximately three passes are required for fresh feed to report as product. Segregation of the tracer pellets in the system, according to their diameter, was observed and reasons for this are suggested. These results should be of potential use in the modeling and control of ball balling circuits in the iron ore industry.

Jan 1, 1985

By R. W. Fountain, John Chipman

The solubility of nitrogen in Fe-B alloys (0.001 to 0.91 pet B) is determined by the Sieverts' technique for temperatures of 950° to 1150°C. The activity coefficient of nitrogen is decreased by boron. The three-phase equilibrium between ? iron, BN, and gas is established and also the four-phase equilibrium between iron, BN, Fe2B, and gas. The above equilibria are calculated for a iron. The relation of these data to hardenability and strain aging of boron-treated steels is discussed. BORON additions are known to enhanbe the hardenability of heat-treatable steels and to assist in the control of strain aging in sheet steel for deep drawing. The increase in hardenability is explained by the theory that adsorption of boron on austenite grain boundaries reduces their free energy and thus retards ferrite and upper bainite nucleation.l,2 Digges and Reinhart3 have shown that the full effectiveness of boron in commercial steels is achieved only when strong nitride formers such as titanium and zirconium are also present. The influence of nitrogen on eliminating the boron contribution to hardenability was also demonstrated by Shyne and Morgan.4 These workers prepared Ni-Mo steels containing either nitrogen or boron or nitrogen plus boron. The nitrogen-plus-boron steels showed the lowest hardenability which was attributed to the presence of stable nucleating particles, presumably nitride. Morgan and Shyne5-7 have shown that boron in the amount of 0.007 pet will completely eliminate strain aging due to nitrogen in low-carbon, open-hearth steels. In addition, by proper control of the boron additions, a rimming steel can be produced. Since the effectiveness of boron on hardenability and eliminating strain aging is influenced by the amount and distribution of the nitrogen in the steel, the present study was. undertaken to determine the influence of boron on the solubility of nitrogen in iron. EXPERIMENTAL PROCEDURE The solubility of nitrogen in Fe-B alloys was measured by the method of Sieverts, which consists of determining the amount of gas dissolved by the metal in a constant volume system. The apparatus employed in this investigation and the experimental details have beendescribed previously.B AMcLeodgage was added to the apparatus to allow measurements at very low pressures. The alloys were melted at reduced pressure in a basic-lined induction furnace using electrolytic iron and ferroboron. Ferroboron was added after the primary deoxidation of the iron with carbon. Since it was difficult to attain a constant low level of oxygen by this procedure, silicon was added after the carbon deoxidation and prior to the ferr obor on addition. The alloys were castas 2-in. sq ingots, heated in argon at 1050loC, and forged to 1/4-in. plate. After forging, 1116 in. was machined from each side of the plate to remove any possible contamination, and it was then cold-rolled to 0.010-in. sheet. The sheet was cut into approximately 1/4-in. squares and pickled in an inhibited H2SO4 solution to ensure a clean surface. In the case of the boron alloys, a hydrogen treatment could not be used for surface cleaning because boron losses resulted. The composition of the alloys is given in Table I. For a solubility determination, a 75-g sample was inserted in a quartz tube and sealed in place in the apparatus. The entire system was evacuated at room temperature and leak tested for 24 hr. If no leaks were observed, the system was heated to the temperature of measurement and again leak tested for 24 hr. If no leaks were detected, the hot volume and solubility determinations were begun. The hot volume was determined at a constant temperature for each run by admitting successive amounts of argon and recording pressure vs volume, which, in all cases, resulted in a straightline relationship. The argon was then removed and the procedure repeated with nitrogen. Successive additions were made until the desired nitrogen content of the metal and equilibrium pressure of the system were obtained. The

Jan 1, 1962

By P. V. Martin

SHORTLY after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bes-semer process stimulated a, rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracite and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt,, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast tempera-ture not only resulted in greater output but also reduced fuel consumption far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given tile chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's pains-taking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recog-nition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory.

Jan 1, 1939

By F. F. Aplan

The past year has been another year of vigorous fundamental research in mineral processing as evidenced by the active publication of results, particularly in Germany, Japan, United Kingdom, United States and USSR. It was also noteworthy for several significant meetings and conferences. The Basic Science sessions at the AIME Annual Meeting continued to attract an increasing audience and the sessions were especially notable for the active discussion of papers. The third Engineering Foundation Conference on Particulate Matter Systems,1 chaired by F. F. Aplan, was held in Milwaukee in August and attracted over 100 experts from five continents. Sessions at this week-long conference covered comminution, particle characterization, separation of fine particles, fluid-solid separations as applied to pollution control, flotation kinetics, particle-particle interactions and particle agglomeration. This popular conference will be continued under John Karpinski of Bethlehem Steel Corp. as 1968 chairman.

Jan 2, 1968

By T. S. Washburn

Deoxidation is one of the most complex metallurgical operations in the basic open-hearth process. The necessity for deoxidation arises from the fact that the refining operations that precede it require the oxidation of the steel bath. when the refining is completed and the desired composition of the bath has been obtained with respect to the elements subject to control by 'oxidation. there is usually an excess of oxygen present in the bath from the standpoint of the amount desired in the finished steel. The objectives of deoxidation are to control the amount and type of oxides and, although not directly ilnp1it.d by the term or always considered as a Part of the process, to control the amounts of gases such as hydrogen or nitrogen that will be present in the finished steel. There are other aspects to be consideretl in connection with deoxidizing procedures. In addition to the primary objectives of oxide and gas control. the composition of the steel is affected by the elements introduced during the deoxidizing process. Factors in furnace operations are likewise involved, such as slag composition, temperature control. arid heat time. .ill of these should be considered in establishing the most satisfactory deoxidizing procedure for each grade of steel. The purpose of this paper is to outline the objectives of deoxidation as related to steel characteristics, and to summarize the factors in furnace practice and the economic aspects to be considered in connection with deoxidation procedures. Objectives of Deoxidation The primary objectives of deoxidation are the formation and elimination of oxides. The amount of oxygen present in the bath prior to deoxidation is an important factor, since it is the basis of any deoxidation procedure. The oxygen content of the bath is primarily a function of the carbon content, although it is affected also by the temperature, the oxidation of the slag, and transient conditions within the furnace. The relation of oxygen to carbon in the bath is shown in Table I. Table I shows that under actual operating conditions, the amount of oxygen present in the bath is higher than the theoretical amount. This relation would be expected, since the bath is in a state of metastablc equilibrium during the period that the carbon is being eliminated. The most important feature demonstrated by this table, however, is the rapid increase

Jan 1, 1945

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By Graham Bright

METAL mines were developed long before coal mines and the early lighting of underground workings was effected by torches and candles. The early coal mines were outcrop workings and little trouble was experienced from gas, but as the mines became deeper and shaft mines were opened it became apparent that an open-flame lamp was exceed-ingly dangerous where gas occurred. No satisfactory way of lighting gaseous coal mines was found until Sir Humphrey Davy brought out his famous safety lamp in 1815. The introduction of the Davy lamp was a great step forward but it was unsatisfactory from a light standpoint because the gauze absorbed a large percentage of the light given out by the flame. Clanny corrected this by the introduction of a cylindrical glass lens, which not only per-mitted a free distribution of the light from the flame but added greatly to the safety by eliminating the possibility of the flame coming in contact with the gauze and by protecting the flame against air currents. A very complete story of the flame safety lamp since its inception is given in the U. S. Bureau of Mines Bulletin No. 227, by J. W. Paul, L. C. Ilsley and E. J. Gleim, published in 1924. A little more recent publication, known as Safety in Mines Research Board Paper No. 4, entitled "The Light Power of Flame Safety Lamps," by R. V. Wheeler and D. W. Woodhead, was published in England in 1927. The flame safety lamp was the-only lamp available for gaseous mines for about 100 years. Although the incandescent electric lamp has been in use over 50 years, it was not found safe to use this lamp from wired circuits in gaseous locations. The storage battery was advocated shortly after the develop-ment of the incandescent lamp but until the introduction of the tungsten filament in the miniature mine-lamp bulb, the battery lamp was not a real possibility because of the excessive weight of the battery necessary to produce a sufficient amount of light. The actual development of the electric-battery type of lamp took place largely between 1910 and 1915. In England and Europe, the development was almost entirely along the

Jan 1, 1935

By David L. Riley

Organization The Foundling Years - 1901-1921 Two events that occurred in the decade of the 1870's have had far- reaching effects upon the petroleum industry in the U. S. and formed a basis for the birth and growth of the petroleum engineering profession. In 187 1 a group of mining engineers banded together to form the American Institute of Mining Engineers "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means". Although it was to be 30 years before an event in Jefferson County, Tex., would cause petroleum to come into prominence as the world's principal source of energy, the founding of AIME provided an organization through which the application of engineering to the recovery of petroleum and natural gas could be developed. In 1875, a Pennsylvania judge who was called upon to make a decision for which there was no precedent reasoned that oil and gas were like wild game - they belong to the man who can reduce them to possession. His decision sired the "rule of capture", which stated that a landowner possesses the oil produced from his well, even though it might have come from beneath his neighbor's land. This interpretation prevailed for more than half a century, during which time gold-rush tactics were employed in the drilling and production of many oil fields in the U. S. The resulting overproduction and tremendous waste led to a virtual economic collapse of the U. S. petroleum industry by the early 1930's. To bring these malpractices under orderly control, proration and conservation policies were developed, and petroleum engineering became the medium through which they were devised and implemented. At the turn of the 20th Century, more than 90 percent of this country's oil production came from the East, but the picture changed with dramatic suddenness on Jan. 10, 1901. Captain Anthony F. Lucas, an Austrian mining engineer, had noticed concentrations of oil and gas near salt domes during mining operations on the Louisiana Gulf Coast. In 1899 he leased a low mound near Beaumont, Tex., began drilling, and after almost 2 years of intermittent operations, brought in the famous "Lucas Gusher"

Jan 1, 1971

By E. A. Steigerwald, G. L. Hanna

The influence of work-hardening exponent on the variation of fracture toughness with material thickness was studied for high-strength steel, aluminum, and titanium alloys. The results indicate that, when materials are compared at similar fracture toughness to yield strength ratios, the material with the lower work-hardening exponent undergoes the transition from flat to slant fracture at a larger thickness than material with a high work-hardening exponent. In the thickness range where complete slant fracture is obtained the reverse is true and a lower work-hardening exponent results in a lower fracture toughness. The influence of work-hardening exponent on fracture toughness is, therefore, dependent on the particular fracture mode. In the transition region a low work-hardening exponent is beneficial for fracture toughness while in the 100 pct slant region it is detrimental. THROUGH the use of fracture mechanics analyses, the influence of geometric variables on the crack propagation resistance of structures can be interpreted with reasonable consistency. However, in order to gain a more complete understanding of the fracture process, the influence of material parameters on crack propagation must be defined and coupled to the macroscopic fracture mechanics approach. The work-hardening exponent, which characterizes specific material behavior, may serve as an effective parameter to allow some degree of coupling to be accomplished. In the extension of a crack in a specimen of suitable dimensions the propagation process occurs in a stable manner when the crack extension force is balanced by the resistance to crack extension, which exists in the material at the crack tip. As the applied stress, and therefore the crack extension force, on the specimen increases, the resistance also increases primarily because the effective plastic zone at the crack tip, which is the main energy absorption process, becomes larger. Since the work-hardening rate of a material influences the stress-strain relationship, it will also influence the energy absorption process in the plastic enclave at the crack tip and hence should have an effect on crack propagation. A number of studies have been made correlating the strain-hardening exponent or the strain to tensile instability with the ability of a material to resist fracture. Gensamer1 concluded that a low-strain-hardening exponent would result in a steep strain gradient at the base of a notch. He reasoned that a large work-hardening coefficient would result in high-energy ab- sorption due to the increased area under the stress-strain curve. Larson and Nunes2 experimentally observed in Charpy tests on steels heat-treated to below 200,000 psi yield strength that the energy to failure in the fibrous mode, i.e., above the brittle-to-ductile transition temperature, was logarithmically related to the strain-hardening exponent. In order to avoid the complicating effects present in studying materials which undergo a brittle-to-ductile transition, Ripling evaluated the notch sensitivity of a variety of fcc metals with varying work-hardening exponents.3 The results indicated that the relative notch sensitivity, as determined from tests on specimens with a sharp notch, decreased with increasing values of strain hardening. Although the energy required for ductile or fibrous fracture increases with increasing work hardening, high-strength steels often exhibit improved crack propagation resistance when heat-treated to obtain low values of strain hardening.4,5 An analysis of whether low strain hardening is beneficial or detrimental to crack propagation resistance must depend on the particular fracture criterion involved. At temperatures where the material is relatively ductile and the development of a critical strain is required for fracture, high strain hardening increases the energy required to produce failure. In the transition region and below, however, a critical stress law appears to be valid6 and a low rate of work hardening may produce superior resistance to semibrittle crack propagation. The experimental program is aimed at studying these possibilities and determining the specific influence of strain hardening on the crack propagation resistance of several high-strength materials. MATERIALS AND PROCEDURE The alloys, chosen as representative of various classes of high-strength materials, are summarized in Table I. The heat treatments evaluated along with the smooth tensile properties are presented in Table 11. Pin-loaded sheet tensile specimens were employed to determine the smooth tensile properties. A strain gage extensometer (measuring range 0.200 in.) was used at a strain rate of 0.02 in. per in. per min. The work-hardening exponents were determined from the stress-strain curves generated in the smooth tensile tests and the assumption that the portion of the stress-strain curve beyond the yield point can be described by the power relationship: where a is the true stress, P is the true plastic strain,

Jan 1, 1969

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry's annual fatality experience. In recent years workmen's compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera' roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949

By Robert Keeney

AT the beginning of the use of the electric furnace, for the manufacture of calcium carbide and ferro-alloys, experimental work was conducted in it upon the production of steel from iron ore. Stassano performed two series of experiments in Italy, the first1 during the years 1898 to 1902, and the second2 in 1908. For many years steel and wrought iron have been produced directly from ore on a small scale in the forge, crucible, and reverberatory furnaces; but the difficulties attending the operation of these combustion processes have prevented their adoption to any great extent. The combustion

Jan 2, 1914

By John C. Calhoun, R. C. Newman

A report is made of experimental work performed on the capillary retention of water within porous solid systems, the displacement being accomplished with air and various organic liquids. A portion of the experiments were designed to measure the lowering of vapor pressure of water within a porous solid with subsequent conversion of such vapor pressure data to capillary pressure values. The form of the capillary pressure curve at high capillary pressures has been elucidated from this data. Certain theoretical approaches are presented to indicate the correlation between work done by previous investigators. The present work is correlated also with theory. Surface area values are calculated for the various core systems studied. INTRODUCTION Leverettl in 1941 presented a paper which gave the essential concepts of capillary behavior in porous solids. His presentation included both theoretical and experimental aspects of the problem. He defined the term "capillary pressure" and applied it to an ideal porous system. His work included the definition of a dimensionless quantity which was a function of fluid saturation and which could be correlated with porosity and permeability for clean, unconsolidated sands. His experimental work was performed by the drainage of water from packed columns of unconsolidated sands. Subsequently, other authors have presented experimental techniques which permit the determination of capillary pressure data on small core samples. Data have been presented on porous systems other than unconsolidated sand and with the use of liquids other than water. Notable among these are the works of Hassler, Brunner and Deahl,2 Bruce and Welge,³ Amyx and Yuster, and Purcell. Others have indicated the applicability of such data to field problems without regard to the theoretical aspects of the capillary pressure saturation function. Within the recent published literature there have also been reported studies of the correlations between capillary pressure data and other fundamental properties of porous solids. It was the intent of the present reported work to investigate the behavior noted by water and various other liquids within porous systems in an attempt to amplify existing correlations between capillary properties, surface properties, and other fundamental characteristics of porous systems. The experimental work described here was performed as two different investigations but due to its nature it is reported as separate phases of the same general topic. CAPILLARY PRESSURE AND VAPOR PRESSURE LOWERING It has long been recognized that the vapor pressure above the curved surface of a liquid is a function of the curvature of the liquid surface." The capillary pressure is also a function of the curvature of the liquid surface. Both capillary pressure values and vapor pressure lowering are, therefore, functions of the liquid saturation of a porous solid. A quantitative relationship between the vapor pressure lowering and the capillary pressure can be simply developed by considering a porous solid system containing water in equilibrium with its vapor. The capillary pressure at any height within the system is defined as Pc= Pv -P1.......(1) where PI is the pressure in the vapor phase and PI is the pressure in the liquid phase. Consider that both the water and its vapor are continuous phases within the system and that at any point the two phases are in equilibrium. The gradients in the liquid and vapor columns within the porous system are: PI = plgdh dPv = pvgdh By integrating these gradients from the point where h = 0 to the height h, values of PI and PI at the point h are found. Let the point where h = 0 be that where Pc = 0. At this point also Pv is equal to Pve, the equilibrium vapor pressure of the liquid above a flat surface. From the first of these integrations since p is independent of height: P = p1gh + P, From the second, by substituting pv = PvM/RT, where M is the molecular RT weight: Pv M Pvo- RT gh By combining the two last equations to eliminate h, one obtains: P1 RT Pv Substituting, values for Pv and Pi in equation (1) gives PyRT RT Pv which is approximately Pc=RT/Mp1 In Pvo/Pv .......(2) This equation relates the vapor pressure above a curved surface with the capillary pressure across the curved surface in terms of measurable quantities. The equivalent of this equation is given by Freundlich."

Jan 1, 1949

By John C. Calhoun, R. C. Newman

A report is made of experimental work performed on the capillary retention of water within porous solid systems, the displacement being accomplished with air and various organic liquids. A portion of the experiments were designed to measure the lowering of vapor pressure of water within a porous solid with subsequent conversion of such vapor pressure data to capillary pressure values. The form of the capillary pressure curve at high capillary pressures has been elucidated from this data. Certain theoretical approaches are presented to indicate the correlation between work done by previous investigators. The present work is correlated also with theory. Surface area values are calculated for the various core systems studied. INTRODUCTION Leverettl in 1941 presented a paper which gave the essential concepts of capillary behavior in porous solids. His presentation included both theoretical and experimental aspects of the problem. He defined the term "capillary pressure" and applied it to an ideal porous system. His work included the definition of a dimensionless quantity which was a function of fluid saturation and which could be correlated with porosity and permeability for clean, unconsolidated sands. His experimental work was performed by the drainage of water from packed columns of unconsolidated sands. Subsequently, other authors have presented experimental techniques which permit the determination of capillary pressure data on small core samples. Data have been presented on porous systems other than unconsolidated sand and with the use of liquids other than water. Notable among these are the works of Hassler, Brunner and Deahl,2 Bruce and Welge,³ Amyx and Yuster, and Purcell. Others have indicated the applicability of such data to field problems without regard to the theoretical aspects of the capillary pressure saturation function. Within the recent published literature there have also been reported studies of the correlations between capillary pressure data and other fundamental properties of porous solids. It was the intent of the present reported work to investigate the behavior noted by water and various other liquids within porous systems in an attempt to amplify existing correlations between capillary properties, surface properties, and other fundamental characteristics of porous systems. The experimental work described here was performed as two different investigations but due to its nature it is reported as separate phases of the same general topic. CAPILLARY PRESSURE AND VAPOR PRESSURE LOWERING It has long been recognized that the vapor pressure above the curved surface of a liquid is a function of the curvature of the liquid surface." The capillary pressure is also a function of the curvature of the liquid surface. Both capillary pressure values and vapor pressure lowering are, therefore, functions of the liquid saturation of a porous solid. A quantitative relationship between the vapor pressure lowering and the capillary pressure can be simply developed by considering a porous solid system containing water in equilibrium with its vapor. The capillary pressure at any height within the system is defined as Pc= Pv -P1.......(1) where PI is the pressure in the vapor phase and PI is the pressure in the liquid phase. Consider that both the water and its vapor are continuous phases within the system and that at any point the two phases are in equilibrium. The gradients in the liquid and vapor columns within the porous system are: PI = plgdh dPv = pvgdh By integrating these gradients from the point where h = 0 to the height h, values of PI and PI at the point h are found. Let the point where h = 0 be that where Pc = 0. At this point also Pv is equal to Pve, the equilibrium vapor pressure of the liquid above a flat surface. From the first of these integrations since p is independent of height: P = p1gh + P, From the second, by substituting pv = PvM/RT, where M is the molecular RT weight: Pv M Pvo- RT gh By combining the two last equations to eliminate h, one obtains: P1 RT Pv Substituting, values for Pv and Pi in equation (1) gives PyRT RT Pv which is approximately Pc=RT/Mp1 In Pvo/Pv .......(2) This equation relates the vapor pressure above a curved surface with the capillary pressure across the curved surface in terms of measurable quantities. The equivalent of this equation is given by Freundlich."

Jan 1, 1949

By William E. Ford, Edward Salisbury Dana

276. Cohesion, Elasticity. - The name cohesion is given to the force of attraction existing between the molecules of one and the same body, in con- sequence of which they offer resistance to any influence tending to separate them, as in the breaking of a solid body or the scratching of its surface. Elasticity is the force which tends to restore the molecules of a body back into their original position, from which they have been disturbed, as when a body has suffered change of shape or of volume under pressure. The varying degrees of cohesion and elasticity for crystals of different minerals, or for different directions in the same crystal, are shown in the prominent characters: cleavage, fracture, tenacity, hardness; also in the gliding-planes, percussion-figures or pressure-figures, and the etching-figures.

Jan 1, 1922

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By C. P. Proctor, E. D. Hummer, J. A. Younkins

COMPARATIVELY little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission of any effluent of high solid content to be replaced by clean water in order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the purpose of this paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settling and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." GENERAL ARRANGEMENT OF WATER SYSTEM So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers.1.2 The washer, which handles 0 to 4-in. raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. r) consists of twin 48-in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10 ½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By Earl W. Palmer, Cyril Stanley Smith

StKip of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. Mechanism of Ear Formation It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942