Search Documents

By R. D. Carter

Nurnerical .solutions are presented to some problems of unsteady-state radial flow of gas in which Darcy's law holds. These solutions are intended to aid in explaining the observed behavior of gas wells during drawdown tests. The variation of viscosity and Z-factor with pressure is accounted for in the solutions. Results are presented for three types of problems: (I) unfractured wells producing at a constant rate, (2) fractured wells producing at a constant rate and (3) unfractured wells producing through a critical flow prover. In the critical-pow-prover solutions, a correction of the calculated well-bore pressure to account for non-Darcy flow is made. A good correlation is shown between the solutions to the problem of Type 1 and the corresponding diffusivity-equation solution. Using this correlation, the diffusivity solution may be used to obtain gas-well solutions. The solutions to the problems of Type 2 illustrate the difference in drawdown-curve behavior to be expected between fractured and unfractured gas wells. Methods for estimatting fracture radius and flow capacity are presented and verified from solutions of Type 2. The solutions to the problems of Type 3 illustrate the differences to be expected between critical-flow-prover drawdown tests and constant-rate tests. An equation is presented for correcting critical-flow-prover data to constant-rate conditions. A description of the methods used in obtaining the solulions appears in the Appendix. INTRODUCTION It is necessary for many engineering purposes, such as predicting future deliverability performance, to be able to relate bottom-hole flowing pressure, formation pressure and flow rate for conditions of stabilized flow in gas wells. This information is customarily given as a plot of on logarithmic co-ordinates. It is desirable to be able to predict stabilized performance curves for gas wells based on data obtained from drawdown tests of short duration. Tests of long duration may be wasteful of gas, and low-permeability wells do not stabilize in a short-duration test. Although it is now commonly recognized that non-Darcy flow plays a significant part in gas-well behavior, it is believed that an understanding of transient behavior of systems obeying Darcy's law is still important in the interpretation of short-term test data, and the prediction of stabilized performance curves therefrom. In this connection, an equation for correcting Darcy flow It seems likely that solutions of the type presented herein, combined with the non-Darcy flow correction of the type of Eq. 1 and the usual laminar-flow skin factor, could provide a model which would adequately explain transient gas-well behavior for times after the non-Darcy flow region (which should be confined to a small area surrounding the well) has been established. The solutions presented in this paper are for three types of problems: (1) unfractured wells producing at a constant rate, (2) fractured wells producing at a constant rate and (3) unfractured wells producing through a critical flow prover. In the problems of Types I and 2, no corrections for non-Darcy flow were made in the results presented, since it was reasoned that the constant-rate boundary condition would facilitate such a correction if it was desired later. For the problems of Type 3, however, a condition of varying flow rate required that a non-Darcy flow correction of the type of Eq. 1 be included. This was done. Based on the numerical results presented, a number of approximations and a correlation are presented which may be useful in analyzing gas-well test data. It is assumed that the system can be described as a finite cylindrical gas reservoir produced by a single cylindrical well located at the center of the reservoir. Flow is strictly radial.

By P. C. Upadhyay, J. G. Singh

Reissner's thick plate bending theory has been recast for rocks which exhibit the property of double elasticity: different Young's modulus and Poisson's ratio in compression and tension. The governing differential equation and other relevent expressions have been presented in a form compatible to the applied mechanics results so that they can readily be used. Effect of the ratio of Young's modulii in compression and tension, (Ec/Et), on the maximum plate deflection and the maximum bending moments has been evaluated over a wide range. It has been found that the inclusion of bi-modulus property through a parameter (ß = Ec/Et), changes the sheer deformation of the plate to such an extent that the bi-modular effect of rock cannot be overlooked in the thick plate analysis, especially when ß is expected to be greater than 2.

Jan 1, 1982

By W. W. Whitaker, C. W. Manry, R. H. McLean

In an eccentric annulus, cement may favor the widest side and bypass slower-moving mud in the narrowest side. Tendency of the cement to bypass mud is a function of the geometry of the annulus, the density and flow properties of the mud and cement and the rate of flow. Bypassing can be prevented if the pressure gradient protluced from circulation of the cement and buoyant forces exceeds the pressure gradient necessary to drive the mud through the narrowest side of the annulus at the same velocity as the cement. In the absence of buoyant forces, one requirement for this balance is maintenance of the yield strength of the cement greater than the yield strength of the mud multiplied by the maximum distance from the casing to the wall of the borehole and divided by the minimum distance. If the yield strength of the cement is below this value, bypassing of mud cannot be prevented unless buoyant forces or motion of the casing significantly aid the displacement. INTRODUCTION Successful primary cementing leaves no continuous channels of mud capable of flow during well treatment and production. Prevention of channels requires care. Tep-litz and Hassebroek provide evidence of channels of mud after primary cementing in the field.' Channeling of cement through mud in laboratory experiments has also been reported.'-' Recommendations for improving the displacement of mud include (1) centralizing the casing in the borehole,'-" 2) attaching centralizers and scratchers to the casing and moving it during displacement,18 "3) thinning the isolating the cement by plugs while it is circulated down the casing,%( (5 establishing turbulence in the cement," and (6) holding the cement slurry at least 2 lb/gal heavier than the mud and circulating the cement slurry at a very low rate of flow.' Although much has been written about the above parameters, the relative importance of each has not been well defined. In this investigation, the mechanics of mud displacement are described through results from analytical models and experiments. The model chosen — a single string of casing eccentric in a round, smooth-walled, impermeable borehole — is analagous to casing centralized in a borehole which is not round and to placing more than one string of casing in a borehole. In each, some paths for flow are more restricted than others. A fluid flowing in the borehole may seek the least restricted, or most open, path. This tendency for uneven flow can lead to channeling of cement through mud unless preventive measures are taken. The analytical models describe channeling and give means of balancing the flow. Experimental data test the analytical models and illustrate effects of motion of the casing, differences in density and mud's tendency to gel. Results are encouraging. Piston-like displacement of mud by an equal density cement slurry is possible through proper balance of the flow properties of the mud and cement slurries to the eccentricity of the annulus. The more eccentric the annulus, the thicker must be the cement relative to the mud. If proper balance is not achieved. bypassing of mud by cement cannot be prevented without assistance from motion of the casing or buoyant forces. Increasing the rate of flow can help to start all mud flowing but cannot prevent channeling of cement through slower moving mud in an eccentric annulus. Thinning the cement slurry tends to increase channeling although the extent of turbulence in the annulus may be increased. Description of flow in an eccentric annulus begins in the next section. It is assumed that (1) the casing is eccentric and is stationary, (2) the mud and cement slurries have the same density and (3) the gel structure of the mud has been broken and the mud and cement follow the Bingham flow model. Effects related to these restrictions will be discussed. FLOW PATTERNS SlNGLE FLUID IN ANNULUS Flow of a single fluid through an eccentric annulus is illustrated in Fig. 1. Part A shows laminar flow of a Newtonian fluid. This distribution of flow was calculated by Piercy, Hooper and Winney.' In fully developed turbulent flow, the velocity distribution around the annulus is less distorted, but the flow still favors the widest part of the annulus Parts B, C and D of Fig. 1 are a qualitative representation of the flow of a Bingham fluid. The yield strength of the fluid increases the severity of bypassing compared to Newtonian flow. At a very low rate of flow, all flow is confined to that portion of the annulus which has the minimum perimeter-to-area ratio. The fluid shears on the perimeter of that area when the pressure gradient multiplied by the area just exceeds the yield stress of the fluid multiplied by the perimeter. Whether or not the minimum perimeter-to-area region encompasses all of the annulus or only a part (as shown in Part B) depends on the geometry of the annulus. If only a part begins to flow, increasing the rate of flow increases the area flowing until finally there is flow throughout the annulus.

By John C. Calhoun, Raymond G. Loper

Theoretical calculations for the decline of pressure and the variation of instantaneous producing gas-oil ratio with increased cumulative production have been made for reservoir systems under various producing drawdown values and for various spacings. These variables have been included by a modification of previously Published techniques. This consists essentially of utilizing a radial system flowing gas and oil in a succession of steady state calculations. The results of the calculations do not show any variation in the predicted behavior of the internal gas drive reservoir when either the drawdown or the spacing are changed. The prediction of performance on an internal gas drive reservoir has been presented by various authors. ',"' These predictions are in the form of a pressure decline and an instantaneous producing gas-oil ratio as a function of cumulative oil withdrawal. In making these predictions a basic assumption has been that the saturation of the reservoir is uniform throughout at any time, or that the pressure differential imposed on the reservoir system is zero. Because of these assumptions the validity of such predictions has been questioned. Their application to actual systems, where saturations are not uniform and where producing differentials exist, has been a hazardous procedure. The authors cited have used different methods of approach to the derivation of equations for making their predictions and for arriving at a solution of both equations, but basically the same relationships are utilized in each case. In all instances the instantaneous producing gas-oil ratio is calculated from the equation: In utilizing this equation an average reservoir pressure and an average reservoir saturation must be known, the former to define ß, v, s, and uo/ug and the latter to define kg/ko. Predictions can be made, therefore, only for the conditions of a uniform reservoir saturation and a uniform reservoir pressure. This restriction of requiring a uniform oil saturation can be resolved by applying two-phase steady state flow for the radial system to the reservoir's history. Radial steady state flow is defined when the ratio of phases flowing,

Jan 1, 1949

By John C. Calhoun, Raymond G. Loper

Theoretical calculations for the decline of pressure and the variation of instantaneous producing gas-oil ratio with increased cumulative production have been made for reservoir systems under various producing drawdown values and for various spacings. These variables have been included by a modification of previously Published techniques. This consists essentially of utilizing a radial system flowing gas and oil in a succession of steady state calculations. The results of the calculations do not show any variation in the predicted behavior of the internal gas drive reservoir when either the drawdown or the spacing are changed. The prediction of performance on an internal gas drive reservoir has been presented by various authors. ',"' These predictions are in the form of a pressure decline and an instantaneous producing gas-oil ratio as a function of cumulative oil withdrawal. In making these predictions a basic assumption has been that the saturation of the reservoir is uniform throughout at any time, or that the pressure differential imposed on the reservoir system is zero. Because of these assumptions the validity of such predictions has been questioned. Their application to actual systems, where saturations are not uniform and where producing differentials exist, has been a hazardous procedure. The authors cited have used different methods of approach to the derivation of equations for making their predictions and for arriving at a solution of both equations, but basically the same relationships are utilized in each case. In all instances the instantaneous producing gas-oil ratio is calculated from the equation: In utilizing this equation an average reservoir pressure and an average reservoir saturation must be known, the former to define ß, v, s, and uo/ug and the latter to define kg/ko. Predictions can be made, therefore, only for the conditions of a uniform reservoir saturation and a uniform reservoir pressure. This restriction of requiring a uniform oil saturation can be resolved by applying two-phase steady state flow for the radial system to the reservoir's history. Radial steady state flow is defined when the ratio of phases flowing,

Jan 1, 1949

By M. W. Hayward

THE object of this paper is to record and tabulate the data and field observations obtained by the writers and their associates during 10 years of intensive study of lead-zinc deposits in the Cretaceous limestone areas in Northern Mexico, particularly in mines owned by the Cia Minera de Peñoles, S. A. At the El Paso meeting of the Institute in October, 1930, J. G. Barry made the suggestion that a committee be appointed to correlate the ideas and theories which have been put forth by the numerous engineers and geologists who, during recent years, have made a study of the ore deposits in the area under consideration. The first step in a work of this nature would be to record all of the observed facts, and these facts would have to be accepted by those who attempted to formulate a theory of ore deposition. It is with this idea in mind that the writers have described as accurately as possible the actual, observed facts pertaining to the occurrence of the lead-zinc ores in dolomites or dolomitic horizons. By most writers the term "dolomite" is loosely used to designate magnesium-bearing limestones, regardless of the percentage of MgO present. Since no true dolomites exist in the areas to be described, we shall also loosely use the terms dolomite or dolomitic limestone to desig-nate those beds having a magnesia content of 5 per cent MgO or more. For a number of years the writers have been impressed with the fact that in areas where dolomite beds occur a large percentage of the lead ore is found in these beds, in spite of the fact that such beds may be overlain or underlain by pure limestone, which one would assume to be just as favorable for replacement as the dolomite, if not more so on account of its being more soluble in acid solutions than the dolomite. It is true that in some limestone areas, such as the Erupcion-Ahumada districts, Chihuahua, and Providencia, Zacatecas, where no dolomite beds have been found, large tonnages of lead ores have been mined. We venture to predict, however, that had there been dolomitic beds in these areas, the

Jan 1, 1932

By E. M. Wise

The practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgrenl and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward12 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents15 and are becoming of commercial importance in the production of high-strength castings. The equilibrium relations existing in the high-copper region of the copper-nickel-tin system have been carefully studied by Eash and Upthegrove,6 and in somewhat less detail by Veszelka.7 The observa-

Jan 1, 1934

By D. L. Albright, G. A. Colligan

An investigation has been conducted to determine the nature of the crystallographic substructure of nickel and a 1.0 wt pct Ag-Ni alloy which had been undercooled 105°C prior to solidification. A rotating back-reflection X-ray technique and modified Weissmann diffractometer were used to orient single-crystal sections from these poly-crystalline ingots and to determine the substruc-tural features of these single crystals, The sub-grain size in the pure nickel ingot is 0.5 mm diam while the silver-doped nickel subgrain size is only 0.1 mm diam. The misorientation between adjacent subgrains is approximately 1 deg of arc in both ingots, and the spread of orientation of sub-grains about the mean orientation of the crystal is 5 deg of arc in both ingots. The addition of silver results in a stable impurity substructure which is preserved during isothermal solidification and subsequent cooling to room temperature. In the absence of silver the initial impurity substructure is destroyed by dislocation interactions which produce a secondary substructure which grows to a size five times larger than the initial substructure. THE process of undercooling a metal entails cooling of the molten sample below the equilibrium freezing point without the occurrence of solidification, i.e., by exercising proper constraint over the experimental variables contributing to nucleation in the melt. The current work of walker1 and Colligan Metal reports undercooling large continuous samples of nickel by imposing appropriate restrictions upon the parameters of solidification. The silver-nickel equilibrium diagram3 reveals the presence of a monotectic reaction at 1435°C. At this temperature the maximum solid solubility of silver in nickel is approximately 3 wt pct, but this solubility decreases with decreasing temperature and the solute is rejected as a silver-rich liquid phase at temperatures below 1435°C. Thus, the 1.0 wt pct solute should be held in solution during undercooling and solidification and subsequently precipitate as a silver-rich liquid phase at grain and subgrain boundaries following solidification during cooling below 1435. This assumes no solute segregation sufficient to cause the monotectic reaction. One would expect this second phase to inhibit grain and subgrain growth by retarding dislocation motion after solidification is complete. The effectiveness of silver addition in growth retardation of high-angle grain boundaries has been demonstrated by Colligan and suprenantS4 The principal [l00] dendrite growth directions in a 2 wt pct Ag-Ni alloy undercooled 53 all radiated from the nucleation site. A similar pure nickel ingot undercooled 59°C exhibited a random orientation of [l00] dendrite directions with respect to the nucleation site. Since undoped nickel ingots do not retain any evidence of the casting or solidification texture and silver-doped ingots do retain this texture, it is reasonable to assume that considerable grain growth has taken place in the pure nickel. These particular experiments were performed in order to reveal the differences, if any, in the features of the crystallographic substructure of undoped undercooled nickel and silver-doped undercooled nickel. 1) EXPERIMENTAL PROCEDURE Data are reported on selected specimens from two massive (approximately 260 g) undercooled ingots of nickel. One ingot consisted of electrolytic nickel and the other of this same material with 1.0 wt pct addition of high-purity silver. Powder patterns were taken of both the as-received and as-solidified materials; in all cases the reflections recorded were attributable to the individual elements nickel and/or silver. Fig. 1 is a. schematic diagram of the apparatus employed for the undercooling experiments. The equipment consists in part of a fused silica crucible for containing the charge. A fused silica tube encloses the system, which is covered by a brass cap to permit partial sealing of the inert atmosphere. This cap contains a hole through which a Pt-Pt 13 pct Rh thermocouple is inserted for temperature measurement. The charge is inductively heated under a purified argon atmosphere.

Jan 1, 1963

By J. W. Galpin, V. L. Minear, F. C. Sturges, B. H. Mott, R. H. Allen, W. W. Weigel, Wm. D. Owsley, R. E. Moeller

By definition the word "grout" means a thin mortar, or a kind of plaster or ce¬ment, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the-flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1948

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945

By L. R. Testardi, J. R. Wiese

OBSERVATIONS have been made that the substitution of antimony for bismuth in Bi2Te3 leads to anomalies in some of the electrical and magnetic properties of the Bi2Te3-5S2TeS alloy system at the composition ratios 2 Bi2Te3 : 1 Sb2Tes and 1 Bi2Te3 : 2 Sb2Te3. Airapetiants and Efimova1 have reported the peaking of the nondegenerate hole mobilities, at these compositions for sintered materials and ascribe the peaking to the formation of ordered alloys. From a study of these materials produced by the Bridgeman

Jan 1, 1962

By J. L. Jernegan

In a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaftfurnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the varions metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

By Franklin J. Stermole

INTRODUCTION Economic evaluation of an open pit mine is similar to the economic analysis of any major investment project in any industry. It requires (1) taking into account all of the costs and revenues that are estimated to be incurred over the economic life of the project; (2) crediting the project with all the tax savings and tax credits that will be realized over the project life from tax deductions and credits related to various project costs; (3) charging the project with all taxes to be paid on taxable income over the project life; and (4) properly accounting for the time value of money for all project costs, revenues, taxes, tax savings, and tax credits when making the overall project economic evaluation. These considerations must be taken into account for any valid method of economic analysis such as discounted cash flow rate of return (DCFROR) or net present value (NPV) analyses. All economic analyses fall into one of two categories. ( 1 ) comparison of income-producing alternatives, or (2) comparison of service-producing alternatives. The analysis of alternatives in either of these categories can be made by using correctly any of five basic economic evaluation approaches which are. ( 1 ) present value, annual value, (3) future value, (4) rate of return (ROR) , and (5 ) break-even analysis. Of these evaluation techniques, DCFROR and NPV analyses are used most widely for evaluating income-producing alternatives while present worth cost and equivalent annual cost analyses are used most often for the evaluation of service-producing alternatives. In this chapter income- producing alternative analysis is emphasized, so DCF- ROR and NPV are utilized for evaluating the case studies presented.

Jan 1, 1979

By William C. Maurer

A survey of 25 novel drills has shown that spark drills have potential for drilling oil wells and blastholes at higher rates than rotary drills. Available laboratory and field data were extrapolated to drilling rates of 70 to 280 fph for full-scale spark drills. Most of the data used in these extrapolations were from small-scale laboratory tests at atmospheric pressure. Accurate extrapolation of the small-scale spark drill tests to full-scale field drills was complicated by the fact that the effect of fluid pressure in the well bore and the effect of spark size were not known. In order to answer these questions and to more accurately evaluate the potential of spark drills for drilling blastholes and oil wells economically, a high-voltage spark discharge system was assembled. This equipment produced powerful sparks (10,000 joules) equivalent to those that would be used on a 100-kw full-scale field drill. These sparks are 100 times more powerful than those previously used on spark drills, thus eliminating extrapolation of the spark size. In addition, a pressure chamber was modified to enable using these sparks to produce craters in rocks at fluid pressures up to 15,000 psi, thus eliminating extrapolation from atmospheric pressure to the high pressure existing in deep oil wells. These tests have provided considerable information for more accurately evaluating spark drills for oil-field drilling. MECHANISM AND THEORY OF SPARK DRILLING Spark-Drilling Mechanism When a high-voltage capacitor is discharged across two electrodes, the dissipated energy produces a high-temperature, high-pressure plasma for a few µsec. When these sparks are discharged in air, they undergo considerable expansion (Fig. 1) and produce low-pressure pulses (103-

Jan 1, 1970

By Bartlett W. Paulding

Since its introduction to the petroleum industry in 1949 by Clark,1 hydraulic fracturing or "hydrafracing" has developed into a widely respected and useful technique for increasing production from petroleum reservoirs. Even then, Clark described production increases of from 6 to 100 barrels of oil per day (bopd). Since that time, others have described treatments in which production increased from 12 to 456 bopd, from only a show to 40 bopd;2 from 48 to 219 bopd; 3 from 500 to 1400 bopd and from a show to 192 bopd.4 Although representative of only a few of many successful hydraulic fracturing operational6 these increases in production attest to the past and potential value of the hydrafracing technique to the petroleum industry. The technique has received a considerable amount of theoretical and experimental attention.1, 5-20 Unfortunately, however, the degree of general understanding of the mechanics of hydraulic fracturing is still inadequate to solve many recurring problems. The practicing engineer is plagued with difficulties in predicting such factors as: (1) the required pressure and viscosity of the fracturing fluid to not only induce the fracture but to control the extent of its growth, (2) the strength characteristics and amount of proppant to include in the fluid so that the fracture is held open once the fluid pressure is decreased, and (3) the volume of the reservoir influenced by the induced fractures and the resulting increase in production. A major cause of these difficulties is the uncertainty associated with determining the orientation of the hydraulically induced fractures. One's natural conclusion in considering the problem is that the orientation of the fracture would depend on several variables, as, for example, the relationship between the viscosity and injection rate of the fluid and the

Jan 1, 1968

By Boyd Dudley

THE material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridizing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. The object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value.

Jan 12, 1914

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By M. R. Todd, J. Szekely

THE mechanism of carbon oxidation in steelmaking processes has attracted considerable attention in recent years. The generally accepted model postulates that the reaction between carbon and oxygen occurs at the surface of CO bubbles that originate at the suitable nucleation points and subsequently rise through the metal bath.1-4 Although this model describes adequately the behavior of open-hearth type operations, it is not a satisfactory representation of carbon oxidation in oxygen steelmaking processes since it cannot account for either: i) the very high rate of oxidation per unit bath area,or ii) the commonly reported shapes of the curves showing the dependenie of the oxidation rate on the carbon concentration. The very high decarburization rates commonly encountered in oxygen steelmaking processes need no further elaboration; some typical plots of the rate of carbon removal against carbon concentration, taken from a publication by Li, Dukelow, and smith,' are reproduced in Fig. 1. It is seen from the curves that the decarburization tends to decrease from a peak or a plateau once the carbon concentration falls below a certain value; in the experiments reported, this critical value ranged from 1.2 to 0.2 wt pct C. The apparent dependence of the decarburization rate on the carbon concentration indicates that within this region phenomena associated with the transfer of car- bon must play an important if not predominant role. Since the concentration of oxygen in molten iron at steelmaking temperatures (removed from the immediate impact zone) is only about 0.1 wt pct,6 it is clear that simple simultaneous diffusion of carbon and oxygen to the surface of CO bubbles could not account for the rate of carbon transfer being the controlling step at carbon concentrations as high as 1.0 wt pct. The purpose of this communication is to present an alternative model which may explain at least qualitatively the apparent anomalies mentioned and may stimulate further experimental work. The Physical Model. It is suggested that the principal mechanism of decarburization is the reaction between CO bubbles and an emulsion consisting of molten iron and molten iron oxide particles in the vicinity of the "slag-metal interface9'.* This mech-

Jan 1, 1968

By J. A. Musselman, P. F. Gnirk

A study was made of indexed penetrations by a single dull bit tooth under statically applied loads into rock subjected to confining pressures from atmospheric to 5,000 p.si and atmospheric pore pressure. Experimental results obtained with a 45" wedge tooth over the above range of pressures are presented for two limestones and a sandstone, a variely of indexing distances and two degrees of tooth dullness. The optimum distance between successive bit-tooth penetrations required for maximum rock damage and chip formation decreases substantially with increa.sing confining pressure above the brittle-to-ductile transition pressure of a particular rock. However, the distance remains approximately constant for a variation in confining pressure below the transition pressure. At a given confining pressure, the bit-tooth force required lor chip formation is constant for indexing distances greater than optimum, but generally decreases linearly with decreasing indexing distance for distances less than optimum. The chip-formation force data obtained at confining pressures for which the chip-generation mechanism is macroscopic-ally of a pseudoplastic nature compare favorably with previous theoretical results for indexed dull hit-tooth penetrntion into an idealized, rigid, perfectly plastic rock. INTRODUCTION To study the cutting action of a roller-cone bit, the interaction of a penetrating bit tooth with craters formed in a rock surfacc by the passage of previous bit teeth must be considered. Current knowledge of the basic mechanics of bit tooth-rock intcract:on under simulated borehole environmental conditions has been extensively reviewed.',' Particularly of current interest are the effects of bit-tooth shape, distance between successive penetrations and differential pressure at the rock surface on the extent of the interaction. Pertinent to this paper are results of an experimental investigationb f the interaction between successive penetrations by sharp, wedge-shaped bit teeth. It was demonstrated that both bit-tooth angle and differential pressure influence the extent of rock damage between successive bit-tooth penetrations. Specifically, the optimum or minimum distance between successive penetrations required for maximum interact'on or chip generation tends to decrease with decreasing bit-tooth angle and increasing differential pressure. In addition, at differential pressures on the order of 2,000 psi for four va- rieties of limestones and sandstones, the macroscopic mechanism of chip formation exhibits a transition from brittle to ductile. In this paper, experimental consideration is given to successive or indexed penetrat ons by wedge-shaped bit teeth. Since pore pressure in a rock sample is maintained at atmospheric pressure, the differential pressure at the fluid-rock interface is equal to the confining pressure. The degrees of bit-tooth dullness include teeth with flat and round apexes (Fig. 1). Of primary concern in this paper are the bit-tooth forces required for chip formation, the macroscopic mechanism of chip formation and the minimum distance between successive penetrations, i.e., optimum indexing distance required for maximum rock damage, as functions of differential pressure. Of further interest is a comparison of actual bit-tooth chip formation forces at elevated differential pressures with calculated forces from previous theoretical results4 for indexed dull bit tooth penetration into a rigid-plastic rock. EXPERIMENTAL APPARATUS AND PROCEDURE The experimental apparatus consists of a pressure vessel equipped with a piston through the side of the vessel (Fig. 2). A single bit tooth inserted in the lower end of the piston is forced at a desired rate into the rock when the ram pressure chamber is pressurized. Electrical instrumentation incorporated into the apparatus yields a graphical plot of force on the piston as a function of bit-tooth penetration or displacement into the rock. Since the piston and ram assembly are in force equilibrium for a constant confining pressure in the main vessel, the fluid volume in the vessel remains constant during bit-tooth penetration. Hence, the force resisting penetration of the tooth is independent of the force exerted on either end of the as-

By D. W. Lillie

Property changes produced by irradiation of Al-0.4 wt pet Li alloys at 270°C to a burnup of 0.155 pct of all atoms are described. Metallographic evidence of the formation of internal pores and the concentration of gases at grain boundaries is shown. Some conclusions are drawn concerning desirable property characteristics for resistance to radiation swelling. RADIATION induced gases are of great practical significance in nuclear engineering since they affect the behavior of fissionable fuels and control rod materials. In fuels the gases xenon and krypton are the major offenders, producing serious em-brittlement at low irradiation temperatures and gross swelling at high irradiation temperatures. In control rod materials containing boron, the production of helium from the B 10 (n, 0) Li7 reaction produces similar reactions. Since the trend in reactor design is for operation at increasingly high temperatures, the phenomenon of high-temperature swelling by these induced gases has been the subject of considerable recent study. The objectives of such work have been to obtain engineering information and quantitative data on the effects in specific fuels and control rods and to obtain further understanding of the mechanism of gas damage so that more intelligent corrective steps can be made. Analogue systems are often useful for the latter objective and in this case alloys containing Li are suitable in view of the reaction Li6 + n - He4 + He 4. Both products are gases and no serious radiation problem is produced to complicate post irradiation handling. Considerable caution is, of course, necessary in any operations in which tritium release is possible. The present program was initiated to provide a detailed study of the effects of He + H3 generated by irradiation in Li-bearing alloys. The results on Mg-Li solid solution alloys have been reported elsewhere.' This paper presents information on irradiation of an A1-0.4 pct Li alloy in which the lithium was present as highly enriched Li6 in order to maximize the radiation burnup. PROCEDURE The original intent in the selection of the alloy content was to have Li in solid solution at all temperatures. It became apparent, however, that the solubility of Li in A1 was substantially lower than that reported in the original reference consulted.' This was substantiated by the work of Nowak3 who reported solubility of less than 0.01 pct Li at 100°C. The alloy used (0.4 pct Li) was therefore two phase at room temperature. The irradiation temperature was estimated to be about 270° C, and at that temperature all or almost all of the Li would be soluble under equilibrium conditions. The precise state of the alloy under irradiation is not known. Aluminum used was 99.996 pct purity (max. impurities Si 0.002 pct, Mg 0.001 pct, Fe 0.0005 pct, and Cu 0.0005 pct). The lithium was obtained from Oak Ridge National Laboratory; 96.1 + 0.1 pct of the lithium was ~i~, but chemical impurities were 0.25 pct Ca, 0.05 pct Fe, 0.02 pct Na, 0.02 pct Cu, 0.01 pct Sr, and 0.01 pct Ba. The two metals were melted in an alumina crucible in a resistance heated furnace in an atmosphere of helium. A l-in. ingot was cast in an iron mold, machined to %-in. round, hot swaged (350°C) to 0.080-in. round, cold swaged to 0.060-in. round, and finally cold drawn to 0.040-in. round. Four-inch wire lengths were then cut and annealed at 250°C for 4 hr in helium. Irradiations were carried out in a VT hole in the Argonne CP-5 reactor. The wires were held in an aluminum jig, sixteen wires per capsule, and were maintained in a helium atmosphere for maximum heat transfer. Eight wires of pure aluminum and eight of Al-Li alloy were placed in each capsule. Argome Laboratory statements were accepted as establishing flux and exposure levels. These were based on previous experience and flux map-

Jan 1, 1961