Search Documents

By J. B. Clark, A. J. McEvily, R. L. Snyder

The nonuniform distribution of precipitate particles has been recognized as a leading factor contributing to the relatively low fatigue resistance of aluminum alloys. The structure of many of these alloys is characterized by narrow precipitate-free zones adjacent to the grain boundaries. Alloys with such zones exhibit a tendency for brittle inter crystalline fracture. The interrelation between this type of structure and mechanical properties was investigated in an Al-10 wt pct Mg alloy. It was found that deformation during fatigue occurs preferentially along these zones and cracks initiate there. In Al-10wt pct Mg, the zones were found to be supersaturated even after extensive general precipitation and are due to the absence of proper precipitate nuclei in the region near the grain boundaries. Cold working the alloy prior to aging improves the mechanical properties by inducing precipitation within the zones and also by jogging of grain boundaries. The mode of fracture is changed from brittle inter crystalline to more ductile trans granular fracture. THE process of fatigue is highly structure sensitive, with the strength of the whole often dependent upon some localized discontinuity, either geometrical or metallurgical in nature. Much has been learned about the role of geometrical discontinuities, e.g., notches, in fatigue, but with the exception of the effects of inclusions or the shapes of carbides, relatively little is known about the specific effects of discontinuities in metallurgical structure such as nonuniform precipitation. In most age-hardening aluminum alloys, metallo-graphic studies have shown that the extent of precipitation adjacent to grain boundaries is much less than that which occurs in the interior of the grains. The width of these almost precipitate-free regions, which are sometimes called denuded zones, and the extent of solute depletion within them, are dependent upon the particular alloy and its aging treatment. It has been observed1 that these zones are relatively soft with the result that plastic deformation takes place preferentially within them. It has also been shown 2-4 that there exists a tendency for intercrys- talline cracking in fatigue when such zones are present. It is of interest to note that Broom et al.2,3 were able to reduce the incidence of this type of failure in an A1-4 wt pct Cu alloy by stretching the material 10 pct prior to aging. In the present study, the effects of precipitate-free regions on the fatigue properties of an A1-10 wt pct Mg alloy were studied in detail, and the effects of deformation prior to aging on the nature of the precipitation process as well as on fatigue properties were also investigated. MATERIAL AND PROCESSING An A1-10 wt pct Mg alloy was selected for this study, because it was known that well-defined precipitate-free regions along the grain boundaries are readily obtained in this alloy after aging at 200oC.5 The starting materials were 99.998 pct A1 and singly sublimed magnesium of about 99.9 pct purity. The aluminum was induction melted in a graphite crucible, and then the magnesium addition was immersed until dissolved. Chlorine gas was then bubbled through the molten alloy for 4 min to degas the melt, after which the melt was cast at a pouring temperature of 730" to 760°C into a cold, graphite-coated, tapered steel mold. Since A1-Mg alloys are difficult to homogenize,5 special care was taken to obtain a uniform composition. Two-in. cubes were cut from the ingot and heated at 446°C for 30 min. These cubes were then hot forged approximately 35 pct in each of the three cube directions and homogenized for 16 hr at 446°C. Sheet specimens were then obtained by pressing 40 pct and rolling 35 pct per pass with reheating between reduction steps to a final thickness of approximately 0.10 in. The sheet was then solution treated for 16 hr at 446°C and water quenched. The age hardening behavior of this material at 200°C was then determined, and the results are shown in Fig. 1. The age hardening of this alloy when subjected to cold work prior to aging is also shown in this figure. Preliminary work indicated that extensive deformation after quenching was required to affect drastically the precipitate-free regions in this alloy, and a rolling reduction of 50 pct was chosen. For purposes of comparison the following three conditions were studied: a) Solution treated, quenched, and aged 20 hr at 200°C

Jan 1, 1963

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By Frederick Rhines

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ? in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activa-tion heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. Much of the argument concerning the properties of metals that deter-mine D and Q has been drawn from data in which variations of the quan-tities with concentration are unknown, for these data- have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concen-trations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Persifor Frazer

The '(author's edition" of the following paper, "subject to re vision," was received by him, and copies sent to Professor Geikie and others about two weeks before the date of the meeting at which it was to be read. A telegram, and subsequently a letter (both of which unfortunately arrived too late), apprised the present writer that the Director General objected to certain views ascribed to him as the reverse of those which he really held. These views, however interesting, had no very important bearing on the object of the fol lowing notes, which, as must be evident, are devoted to the conside ration of the close analogies between the Welsh and American rocks. Without being able, therefore, to account for the circumstance which Professor Geikie has mentioned, it is thought better in the present revised edition to omit all allusion to Professor Geikie, or Mr. Peach, or their views, except in this place, where I desire to thank them for their courtesy during the time which I had the pleasure of spending in their society. It appears sufficiently throughout the body of the paper that the writer had not the slightest intention of entering the controversy, which was about to commence, concerning the proper horizons of the St. David's rocks, for many reasons; and amongst others because he did not feel that a sojourn of a few days in a difficult region, which had been already studied by many of the foremost geologists of England, would warrant him in adding to the literature on the sub ject. The discussion of the analogies between these rocks and those of the Eastern Appalachians, which he has studied for twelve years, of which eight were spent in the service of the Second Geological Survey of Pennsylvania, was much more to his taste as it was more within his ability, and if he has added anything to the evidence of these analogies, the paper, however imperfect, will not have been written entirely in vain. Right or wrong, he assumes the entire responsibility of what follows.

Jan 1, 1883

By B. H. Bergstram, C. L. Sollenberger

When glass spheres are crushed by slow compression loading, the outer lune-shaped fragments resulting from the fracture consistently fly outward at high velocity. About 45 pct of the strain energy fed into the sphere-platen system reappears in the form of the kinetic energy possessed by these fragments. These measurements were obtained from high-speed photographs. This kinetic energy can be utilized for addtional comminution if the fragments are allowed to impact against a suitable structure. Comminution theory has advanced considerably in recent years by the study of this unit operation under laboratory conditions. Some of the parameters have been isolated, but the experimental measurements of the pertinent quantities, such as energy, particle size, etc., are still only made prior to and after the conclusion of a fracture sequence. The catastrophic fracture process itself has not been adequately studied from a comminution point of view. It has recently been suggested by Gilvarry that the fragments which result from the free crushing of a single glass sphere by slow compression contain a considerable amount of kinetic energy after fracture. This kinetic energy, if properly directed, possibly can be partially utilized to cause additional fracture. In this paper a hypothesis will be presented which suggests that this kinetic energy is necessarily present and that its dissipation is the process by which a large part of the thermal energy imparted to the crushed product is generated. Evidence supporting the existence of kinetic energy and its utilization for secondary fracture will also be presented. THEORETICAL A previous paper4 has shown that the load-deformation curve of a system composed of an elastic sphere gripped by a pair of parallel platens, can be predicted by a consideration of the theories of Hertz as summarized by Timoshenko.' The deformation A, of one half of the system is given by which states that the deformation is a function of the mutually applied load, P, the radius of the sphere, R; and the respective physical properties of Poisson's ratio, v, and Young's modulus of elasticity, Y. The shape of experimental load-deformation curves conform to this relationship. The energy input to the sphere-platen system, can be predicted from the integral of the load acting through the appropriate distance, dA. Since dA can be evaluated in terms of P from the derivative of Eq. 1, this integral can be integrated between limits of 0 and P. The test sphere, however, is loaded at not one but at two points of contact, i.e., at both ends of a diameter, and hence the total energy input, E, is twice the energy input at each end, or The energy input to the system calculated from this equation corresponds to the energy computed from the measured area under the load-deformation curve. Timoshenko, considering the impact of two perfectly elastic spheres, has shown that the inter-penetration distance A is given by - m f (D (^ * ^t w as modified for the special case where one sphere is of infinite radius, i.e., its surface is a plane; where M is the mass of the finite sphere of radius R, and V is the velocity of approach at the start of an impact and also equals the final velocity of separation for perfectly elastic bodies. Because A is also a function of the load and the elastic properties, as shown in Eq. 1, the velocity, V, can also be calculated in terms of the elastic properties and maximum load, P, or

Jan 1, 1961

By A. M. Rahm

PROBABLY the majority of red brass sand castings are judged merely on the basis of outside appearance and the quality of machined surfaces. Many castings, however, must individually withstand a hydraulic or air-pressure test before being accepted as parts of more complicated machin-ery. Finally, there remains a comparatively small group of castings intended for uses of considerable responsibility where only the highest possible characteristics of the metal are acceptable, and for these specially cast test bars are required. The shape of the cast piece from which the test bar must be detached varies greatly from one country to another. The test bar as specified in the American Society for Testing Materials Specification B62-36 is widely used by the American foundry industry. The actual test piece is at the bottom of the cast block and has a riser about six times its mass. It is obvious that this test bar has an advantage over the actual casting. The latter rarely possesses a riser of as much as 30 per cent of its own weight and that riser cannot generally be located in so convenient a manner. Therefore, the characteristics of the test bar cannot possibly correspond to those of the casting itself. It must be taken into consideration that red brass if melted and cast in the best possible manner may show a tensile strength of 40,000 lb. per sq. in. with 35 per cent elongation in 2 in. Such a test bar would indicate that the metal was nearly perfect from the viewpoint of its gas and inclusion content. Barring some accidental defect, a casting cor-responding to such a test bar could be accepted as being quite sound. However, actual specifications do not demand such high characteristics; indeed, few specifications require over 30,000 lb. per sq. in. and 20 per cent elongation, while one Federal specification demands merely 27,000 lb. per sq. in. strength and 15 per cent elongation. It is obvious that

Jan 1, 1939

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By S. R. Balajee, I. Iwasaki

The adsorption mechanism of corn starch and its derivatives at mineral-solution interfaces was investigated by the adsorption of cationic starch, unmodified corn starch, British Gum 9084, and anionic starch on quartz and hematite. The adsorption of these starches, which decreases in the order mentioned, is dependent on the balance between the magnitude of the electrostatic interaction and the magnitude of the hydrogen bonding. There exists a critical starch concentration for both optimum flotation and flocculation conditions of iron ores, which corresponds to a point where the starch adsorption reaches a saturation coverage. Flocculation occurs due to the adsorption of starch via electrostatic and hydrogen-bonding forces and by interparticle bridging as a result of the conformation of starch molecules at the interface. The depressant property of starches and starch derivatives in flotation' and their flocculation char: acteristics in clarification and filtration2.3 have long been recognized on a wide variety of ores. The effectiveness of a starch as a depressant for iron minerals has been the subject of much investigation in recent years both in the amine flotation of siliceous gangue and in the anionic flotation of activated silica from iron ores. It has been reported that the depressant activity of starches and dextrins in the cationic flotation of quartz from hematite increases with molecular weight, branching, and number of hydroxyl groups, 1 and that the selectivity is affected by changing the configuration of starch molecules and the composition of its polar groups.4 ,5 The manner in which starches are solubilized was shown to exert a significant influence as a depressant in the anionic silica flotation, and a series of articles covering the practical aspects of flotation and flocculation have already been reported.618 Chemical modification of the starch structure, the pulp pH, the calcium ion, and the residual starch concentration were identified as some of the more important variables affecting the flotation behavior. In the flocculation of iron ores, it was noted that most starches flocculated suspensions of hematite in water but did not flocculate similar suspensions of quartz,9 and that an excessive use of starch restabilized the suspensions due presumably to protective action. 6 An admirable application of such an observation to practice may be cited in the selective flocculation and desliming in the anionic silica flotation of iron ores, which resulted in superior metallurgy and lower reagent cost. 10 From detailed adsorption measurements, Schulz'and Cooke4 established that the adsorption of starches and their derivatives depended on the types of minerals and of starches, pH, and electrolytes present. Their adsorption data and the foregoing flotation and flocculation observations suggested that an electrical interaction between starches and charged mineral surfaces might be playing a role in their adsorption process. Adsorption of organic polymers, particularly of synthetic origin, at solid-liquid interfaces has been extensively studied in recent years,' and it is realized that their adsorption mechanism is considerably more complex than that of simple ions or molecules. A polymer molecule possesses a number of functional groups, and the adsorption at a point may restrict the adsorbability of adjacent groups. The mechanism may be further complicated by the conformation of the polymer molecules which may exist as coiled spheres, helices, or extended chains as a result of intramolecular interactions among functional groups as well as intermolecular interactions with solvent molecules. The object of the present investigation was to examine the effect of the chemical modification on the adsorption characteristics of starches and starch products on quartz and hematite at several pH values, so that by correlating this information with flocculation and flotation results, adsorption mechanism of starches on mineral-solution interface may be elucidated. EXPERIMENTAL MATERIALS Quartz: St. Peter sand was screened at 35 mesh and the undersize was scrubbed and deslimed at a Fagergren cell. The deslimed sand was cleaned with 0.1 N hot hydrochloric acid and washed repeatedly with distilled water, For anuscript, measurementsl the -200-mesh fraction of the sand was ground dry in a porcelain mill for 3 hr. The specific surface of the finely ground quartz was

Jan 1, 1970

By Thomas W. Dawson

THE H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnage and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center, to center of pulleys. It operated at a speed of 250 ft. per min. and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons were carried by the belt. While this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on, the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and,, therefore, had to be crossed at each location to deliver coal to the river.

Jan 6, 1925

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By G. D. Van Arsdale

This paper describes a series of experiments leading to the development of a method for leaching the mixed ores of the Inspiration Consolidated Copper Co., containing chalcocite and silicates of copper, by the use of solutions acidified with sulfuric acid and carrying ferric sulfate. Iron is added to the solutions and ferric iron is regenerated electrolytically to a percentage high enough to act as an effcient solvent. The decreased yield is partly compensated for by a higher current density. An important problem in modern copper metallurgy, particularly in the Southwest, has been to obtain good recoveries from what are commonly known as mixed ores; that is ores in which the copper occurs partly as oxide and partly as sulfide compounds. The dividing line between mixed ores and ores commonly accepted as concentrating is not definite. In other words, much ore now being concentrated carries considerable copper in non-sulfide form, on which recoveries are not so good as on ores carrying less of these constituents. While treatment by concentration may be commercially profitable on ores carrying oxide copper within certain limits, there are large deposits for which the application of concentration could not be considered, and yet which have not been considered amenable to leaching because they carried too much sulfide. The Inspiration Consolidated Copper Co. has large amounts of such mixed ores, and this paper is an account of the experimental work by which a method was developed for their treatment, and for which a large plant is now being erected by the Inspiration Co. It is not claimed that the method is a general solution of the problem of mixed-ore treatment but it is apparently well adapted for leaching the ores of the Inspiration Co., for which it was designed. The work done has covered preliminary laboratory and test-plant investigation, and a pilot-plant run, extending from March to the middle of December, 1923. Thoroughly consistent and satisfactory results were obtained continuously for more than six months in the pilot plant; and it is believed that the results and probable costs that can be had on a large scale have been definitely proved. The method, however, was designed for local conditions; and while the basic principles are general, there are ores on which it will not work and other ores for which considerable modification may be required.

Jan 1, 1926

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

By J. J. Jakosky

ALL electrical geophysical methods depend for their operation upon the effects produced by the flow of an electric current. By studying these effects it is possible to predict the general axis of current flow. The greater flow of current is in the path of greatest, effective conductivity; and since the effective conductivity of a mineralized zone is different from that of its surrounding envelope (usually much greater), it is possible to locate such a mineralized zone by the distribution of current. Due consideration must be given, of course, to geological structure, to type of mineralization, and to other factors. A number of methods are used to cause this flow of current, and various methods are available for detecting the presence of such current flow and for studying its effects. In a rather detailed way, this paper will discuss the theoretical and practical phases of the inductive methods of geophysical prospecting. ELECTROMAGNETIC GENERATION OF AN ELECTROMOTIVE FORCE The inductive method is so named because the current flowing in the conductor is obtained by electromagnetic induction, instead of by the use of ground electrodes through which a current is passed as in the applied potential systems, or by direct contact with the orebody. An alternating current flowing in a coil will create an electromagnetic field around the coil. This field will have the same frequency as the current and will radiate or travel outward from the coil in closed magnetic or flux circuits: These flux circuits (in air or a homogeneous medium) will be perpendicular to the plane of the coil and will extend or travel outward with uniform velocity in every direction. Maximum field exists in the plane of the coil. Such a coil used for transmitting or as the "energizer" will exhibit similar figure-eight characteristics to those exhibited by the direction-finding coil which will be described in detail later.

Jan 1, 1928

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By Frank G. Miller

The lower cost of producing oil from naturally flowing wells compared with pro-luction costs accruing from artificial lifting methods has stimulated much research, rith the joint purpose of extending the natural flowing life of wells and of increas-ng the productivity of small wells. The iboratory investigation described herein was made to determine the effect of a lotted liner on the pressure gradient in the icinity of the wall of a flowing well. Flow estrictions caused by the liner induce nergy losses between the oil-bearing for-lation and the inside of the liner, which lay be reduced by improved liner design, nd thereby the flow capacity of wells may e increased. These losses have been evalu-ted for rectangular slots of different sizes, nd means are suggested for reducing them. The dearth of information concerning the ature of the flow of fluids from uncon-slidated sands through small openings in he walls of. pipes—as represented by the ow of oil from an oil sand into a slotted ner—is acknowledged. Although the bene-ts to be realized by operators through the se of optimum liners is just beginning to e recognized generally, Coberlyl in 1937 ointed out that the functioning of screen is is an important factor in the pro-uction of oil. From his study on the :lection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string deserves continued study, especially with respect to the selection of perforations. The growing use of gravel packing resulting from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded. Discussion of ProbleM At the beginning of the investigation the following assumptions were made regarding bottom-hole conditions of a producing oil well and the oil-sand reservoir it penetrates: (I) Conditions of steady-state flow exist, (') a a homogeneous liquid is being produced) (3) no contaminating material (such as drilling fluid) is present between the liner and the face of the oil-bearing sand, (4) the well is vertical and completely penetrates a horizontal sand stratum of uniform thickness occurring between two impermeable strata, and (5) the flow is wholly viscous. If the foregoing assumptions are made, with the added requirements that the sand

Jan 1, 1941

By Frank G. Miller

The lower cost of producing oil from naturally flowing wells compared with pro-luction costs accruing from artificial lifting methods has stimulated much research, rith the joint purpose of extending the natural flowing life of wells and of increas-ng the productivity of small wells. The iboratory investigation described herein was made to determine the effect of a lotted liner on the pressure gradient in the icinity of the wall of a flowing well. Flow estrictions caused by the liner induce nergy losses between the oil-bearing for-lation and the inside of the liner, which lay be reduced by improved liner design, nd thereby the flow capacity of wells may e increased. These losses have been evalu-ted for rectangular slots of different sizes, nd means are suggested for reducing them. The dearth of information concerning the ature of the flow of fluids from uncon-slidated sands through small openings in he walls of. pipes—as represented by the ow of oil from an oil sand into a slotted ner—is acknowledged. Although the bene-ts to be realized by operators through the se of optimum liners is just beginning to e recognized generally, Coberlyl in 1937 ointed out that the functioning of screen is is an important factor in the pro-uction of oil. From his study on the :lection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string deserves continued study, especially with respect to the selection of perforations. The growing use of gravel packing resulting from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded. Discussion of ProbleM At the beginning of the investigation the following assumptions were made regarding bottom-hole conditions of a producing oil well and the oil-sand reservoir it penetrates: (I) Conditions of steady-state flow exist, (') a a homogeneous liquid is being produced) (3) no contaminating material (such as drilling fluid) is present between the liner and the face of the oil-bearing sand, (4) the well is vertical and completely penetrates a horizontal sand stratum of uniform thickness occurring between two impermeable strata, and (5) the flow is wholly viscous. If the foregoing assumptions are made, with the added requirements that the sand

Jan 1, 1941

By W. O. Philbrook, C. W. McCoy

The reduction of chromous oxide from lime silica alumina slags by carbon-saturated iron behaves as a first-order process having a rate of 0.001 grams Cr min 1 cm 2 (pct Cr ) , substantially independent of slag composition and temperature over an important range for iron smelting. The equilibrium ratio (pct Cr)/[pct Crl is below 0.04 for slags having lime-silica ratios above 0.6. MANY studies have been conducted on chromium in slag-metal systems under oxidized conditions. The Purpose of these investigations has been twofold; namely, (1) to determine those conditions which lead to greater chromium recovery in electric-furnace and open-hearth practice, and (2) to determine the nature of oxide inclusions and de-

Jan 1, 1959