Search Documents

By A. E. Powers

YEARS of experience and research have shown that molybdenum, tungsten, and vanadium are among the most useful and effective elements in augmenting the high-temperature strength of heat-treatable, ferritic steels. Grün, for example, in conducting an early survey of the strengthening effects of various elements in annealed, low-carbon steel at 750° and 930°F (400° and 500°C), found molybdenum and vanadium to be the most effective.' Holtmann comprehensively studied the strengthening effects of molybdenum and vanadium in quenched and tempered steels at 930°F as a function of microstructure and carbon content.' He found creep strength to be related to the saturation of the austenite at the austenitizing temperature, such that strength is increased by alloying until the y loop is reached—the terminus of complete austenitization. Beyond this degree of alloying, the inability to heat treat will result in lower strength, at least for low and moderate creep temperatures. Tungsten, owing to higher cost than molybdenum, has been little used in ferritic high-temperature steels. As a result, very few investigations have been made of its high-temperature strengthening ability, and reliable data on its effectiveness are not available. Grün rated tungsten far less effective than molybdenum at 930°F (500°C) on a weight-percentage basis.' However, Tammann has found that tungsten is as effective as molybdenum in raising the recrystallization temperature of iron. For this reason Smith, in a review of the subject, has advocated a re-examination of the influence of tungsten on the high-temperature strength of steel.' In any study of the effects of alloying additions on high-temperature properties, recognition must be made of the many variables involved, some of which can be controlled but have been ignored in innumerable investigations of the past, and some of which are difficult or even impossible to control. One cannot, for example, assign a definite strengthening index to any one alloying element, for this will be dependent upon the microstructure (heat treatment and mechanical treatment), testing con- ditions (temperature, time, and stress), and the complete composition of the steel (accompanying alloying elements, impurities, etc.). One ever-appear ing variable, hardness or tensile strength at room temperature, may be eliminated by heat treating all of the alloys to a single hardness level. An attempt may be made to control the variable of primary quenched structure by oil or water quenching the test specimen. The control of such variables may not be possible in cases of widely varying compositions, but at least such deviations should be recognized. Material and Procedure The alloys, made as 30-lb ingots in an induction furnace, all had the same base composition of about 0.18 pct C, 0.85 pct Mn, and 0.48 pct Si. They were grouped as follows: Mo Group—Containing up to 5.2 pct Mo. W Group-Containing up to 6.0 pct W. V Group—Containing up to 3.3 pct V. Mo-V Group—Containing up to 2.7 pct Mo and up to 1.4 pct V. Mo-W Group—Containing up to 2.5 pct Mo and up to 2.5 pct W. The steels, listed in Table I, were forged to ¾ in. sq bars and the material for the high-temperature, rupture-test specimens was further swaged to %-in. round bars.

Jan 1, 1957

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By L. C. Brown, E. B. Hawbolt

The formation of grain boundary precipitates has been studied in Ag-5.64 wt pcl Al alloys at 688°C. Large-grain specinzerzs were used and the boundary misorientation measured by X-ray diffraction. At low-angle grain boundrrries Primary sideplates form. u)hile abore a 17-deg misorientation lenticular precipitates predominate. Growth of the lenticular precipitates was studied on individual grain boundaries using a statistical technique. The thickening and lengthening rates appeared to be independent of &apos;pain boundary misorientation, indicating that grain boundary diffusion was not significant in this system. The precipitates grew urith constant shape, with both the length and thickness increasing parabolically with time. The parabolic lengthening rates were unexpected since previous theory and experimerztal results had indicated linear growth. By approximating the shape of the precipitate to that of an oblate spheroid grouling with constant shape an equivalent diffusion coefficienl was calculated. The zlalue obtained was in good agreement with nleasurements obtained fron, diffusiorz couples. IF a single-phase alloy is heated or cooled to a temperature such that the phase becomes supersaturated, there is a tendency for a second phase to precipitate from it in order to remove the supersaturation. Precipitation takes place initially on grain boundaries due to preferred heterogeneous nucleation, but subsequently Widmans kitten plates may form in the grain interiors if the grain size and supersaturation are sufficient. The type of grain boundary precipitate formed depends on the nature of the boundary. Aaronson1 and clark2 have shown that grain boundary misorientation can be characterized by the simple parameter R, where and X, Y, and Z represent the minimum rotations about three orthogonal axes required to bring the two lattices forming the grain boundary into coincidence. The maximum value for R is 60 deg. In using this parameter the orientation of the grain boundary itself is, of course, neglected. However it was found in both Fe-si3 and A1-Ag2 that the precipitate shape depended only on the parameter R. Clark found that the vast majority of precipitates formed were allo-triomorphs— lens-shaped precipitates that grew along the grain boundaries. At low-angle boundaries, however, (R < 15 deg) Widmanstatten sideplates nucleated at the grain boundaries and grew into the adjacent grains. It has been reported that the rate of growth of grain boundary precipitates is controlled by diffusion within the supersaturated phase.&apos; The theories which have been developed for growth rates have assumed the diffusion coefficient constant over the composition range of the supersaturated phase. This is a fairly good approximation if the composition range involved is not large. Thickening rates have been calculated using the theory developed by Zener4 and by Frank5 for the growth of planar precipitates. A parabolic growth law

Jan 1, 1968

By L. C. Graton

THE Federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of Federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal indus-tries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Be-cause of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final

Jan 11, 1919

By R. J. Borg, C. E. Birchenall

Vapor pressures of eight compositions of Mg-Cd have been determined by the Knudsen effusion technique. Measurements are made at several temperatures for each alloy and the results interpolated to a common temperature for the calculation of the activities. It is not possible to obtain values for the partial molar enthalpies because of the narrow temperature range spanned by the measurements. The results show less precision than those obtained for pure Cd which are also reborted. These alloys are extremely susceptible to corrosion which provides a possible explanation for the lack of precision. Nevertheless, the values of the activity are in good agreement with the results of electromotive force measurements previously reported for the Mg-Cd system. MAGNESIUM and cadmium are mutually soluble in all proportions in the solid state and form a single phase which has the hexagonal close-packed structure. X-ray investigations of this system1,2 have revealed a rapid variation in the relative dimensions of the unit cell occurring at approximately 50 at. pct. The rate of change of the c/a ratio with composition increases markedly for alloys containing more than 50 at. pct Cd. The purpose of this investigation was to determine the activity of Cd in the neighborhood of 50 at. pct and to discover whether or not the thermo-dynamic properties undergo a similar rapid change. The activities are calculated from vapor pressure data obtained by the Knudsen effusion method. Unfortunately the precision of the data from which the thermodynamic values are calculated is insufficient to establish unequivocally a departure from the normal trend. The results are reported primarily because they substantiate the only previously reported activity measurements3 and because they include values for pure Cd which in contrast to those of the alloys show excellent precision. The Cd-Mg system is known to contain several ordered phases. However, this investigation was made at temperatures considerably above the transition temperatures, and the alloys may be regarded as nearly random solid solutions. EXPERIMENTAL Apparatus—The effusion cells are machined from solid tantalum rod. The lids consist of threaded, flanged rings of tantalum onto which are welded shallow cups of 4 mil molybdenum foil. The orifice, which is located at its center, is made by grinding off a small dimple produced with a sharpened punch. Such an orifice has been mounted in plastic, sectioned, and the thickness of the orifice edge measured in a microscope. The maximum thickness is 0.00016 in., and the Clausing factor is consequently equated to unity. The area of the orifice is determined by tracing its projection on the screen of the metallograph at a known magnification and measuring the area of the tracing with a planimeter. Excellent temperature control is achieved with a 4 by 18-in. alundum core, gradient-wound, furnace

Jan 1, 1960

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world&apos;s annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months&apos; to several years&apos; duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis&apos; method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By J. O. Betterton, D. S. Easton

A detailed investigation was made of the phase diagram of silver-zirconium, particularly in the region 0 to 36 at. pct Ag. The system was found to be characterized by two intermediate phases Zr2Ag and ZrAg and a eutectoid reaction in which the -zirconium solid solution decomposes into a-zirconium and Zr2Ag. It was found that impurities in the range 0.05 pct from the iodide-type zirconium were sufficient to introduce deviations from binary behavior, and that with partial removal of these impurities an increase in the a-phase solid solubility limit from 0.1 to 1.1 at. pct Ag was observed. The phase diagram of the silver-zirconium system is of interest as an example of alloying a transition metal from the left side of the Periodic Table with a Group IB element. Silver would normally act as a univalent metal, its filled 4d-shell remaining undisturbed during the alloying. However, there is a possibility that some of the 4d electrons might transfer to the zirconium. An insight into such a question can occasionally be obtained by comparison of phase diagrams. The silver-zirconium system forms part of a more complete review of various solutes in zirconium in which these valency effects were studied.&apos; Earlier work on the silver-zirconium system was done by Raub and Enge1,2 who investigated the silver-rich alloys. After the start of the present experhents, work on this system was reported by Kemper3 and by Karlsson4 which for the most part agrees with the phase diagram presented here. EXPERIMENTAL PROCEDURE The alloys were prepared by arc casting on a water-cooled, copper hearth with a tungsten electrode and in a pure argon atmosphere. Uniform solute composition was attained by multiple melting on alternate sides of the same ingot. Progressive improvements in the vacuum conditions inside the apparatus during the course of the experiments reduced the Vickers hardness increase of the pure zirconium control ingot from 10 to 20 points, observed initially, to negligible amounts at the end of the experiments. Such hardness changes in zirconium are a well known indication of purity. For example, -01 wt pct additions of oxygen, nitrogen, and carbon increase hardness by 6, 10, and 3 VPN respectively. &apos;9&apos; Further verification that the final casting technique did not add a significant quantity of impurities was obtained when pure zirconium was arc cast and then isothermally annealed in the vicinity of the allotropic transition. The transition was always observed to take place over the same temperature range as in the original crystal bar. The alloy ingots were annealed in sealed silica capsules for times and temperatures which varied between 1 day at 1300°C and 60 days at 700°C. The best method found to prevent the reaction of the zirconium with the silica was foil wrapping of molybdenum or tantalum. With this method, samples of pure zirconium were found to be unchanged in hardness after annealing for 3 days at 1200°C. In most of the experiments the protection of these foils was supplemented by an additional layer of zirconium foil inside the molybdenum or tantalum foil. The alloys, foil, and the capsule were outgassed at pressures in the range 10 to l0-7mm Hg in the temperature range 800" to 1100°C before each anneal in order to remove hydrogen and other impurities, and to provide a suitable container for the high purity, inert atmosphere, which is essential in the annealing of zirconium. The temperature measurements were made with Pt/Pt + 10 pct Rh thermocouples calibrated frequently during the experiments against the melting points of zinc, aluminum, silver, gold, and palladium. For the longer anneals the sum of various temperature errors was generally well within ± 2°C. For short-time anneals and during thermal analysis the overall temperature error is considered to be within ± 0.5°C. The compositions of the alloys from the quenching experiments were determined by chemical analysis at Johnson Matthey and Company, Ltd., under the direction of Mr. F. M. Lever. The actual metallo-graphic samples were individually analyzed in every case, and prior to the analyses two or more sides of each specimen were examined to insure that the specimen was not segregated. The sum of the solute and solvent analyses was in each case within the range 99.9 to 100.1 pct. In the course of the experiments, minor impurities in the range 0 to 500 ppm were found to have significant effects on the zirconium-rich portion of the phase diagram. Similar effects had been encountered previously in other zirconium phase-

Jan 1, 1959

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to &apos;85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

[SWEETSER, R. H.: Discussions: on Evaluation of Coal for Blast furnace Coke, 94, 378, 394,385 on Mt. Union Sand Flotation Plant for Preparing Bituminous Coal, 74, 591 on Need for Research in Foundry Pig Iron, 76, 450 on Pig Iron Low in Total Carbon, Is in Demand for Use in Various Industries 75,471 on Properties of Coal Which Affect Its Use in the Ceramic Industry, 101, 254 on Relation of Ash Composition to the Uses of Coal, 74, 471 on Research on Blastfurnace Slags 100, 137.138 on Selection of Coals for the Manufacture of Coke, 74, 637 on Sinter in Blast-furnace Burdens, 100, 54 on Sintering Limonitic Iron Ores at Ironton, Minnesota, 90, 355, 356 on Slag Control in the Making of Iron and Steel, 116, 104, 115, 116 on Solubility of Nitrogen in Liquid Iron, 116, 193, 194 on A Statistical Analysis of Blast-furnace Data, 96, 70]

Jan 1, 1936

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By E. F. Koch, J. L. Walter

oriented crystals of iron and iron with 3, 5, and 6.25 pct Si were rolled to reductions of 10 and 70 to 97 pct at room temperature. Similarly oriented crystals were deformed in tension. Dislocation substructures of the deformed crystals were observed by transmission electron microscopy to determine the effect of silicon on the formation of substructures. Pole figures were obtained to relate orientation changes to substructure. When rolled 10 pct, the iron crystals and the 3 pct Si-Fe crystals formed cells, 1 and 0.2 u in diameter, respecliuely. Cells were absent in the higher-silicon crystals. Extended dislocations and possible stacking faults were observed in the 6.25 pct Si-Fe crystal rolled 10 pct and annealed at 650°C. The stacking-fault energy was estimated to be 20 ergs per sq cm. Rolling to 70 pct resulted in the formation of sub-bands (0.9 µ wide) ill the iron crystals and transition bands (containing 0.2-µ-wide subbands) in the 3 pct Si crystals. No subbands formed in the 5 pct Si-Fe crystal until it was ankzealed. SliP occurred on (112) planes ill tension. The slip traces on the 3 pct Si crystal were wary while those on the 5 pct Si crystal wvere straight. The strain-hardening coefficient for the 5 pct Si crystal was nearly zero. Cells did not form, at least at elongations up to 10 pet. The results suggest that cross slip of iron is restricted by additions of silicon beyond about 3 pct possibly by formation of immobile extended dislocations. IN a previous paper&apos; the authors described the substructures developed in (100)[001]-oriented crystals of 3 pct Si-Fe which were rolled to reductions of 10 to 90 pct at room temperature. At low reductions (10 to 20 pct) cells, approximately 0.2 to 0.3 ja in diameter, were formed. The cell walls consisted mainly of edge dislocations. With increasing reduction (up to 50 pct) the cells were seen to elongate in the rolling direction. In certain regions of the crystal there were significant reorientations which were characterized as rotations about an axis normal to the (100) or rolling plane. These regions were called "transition bands". The regions in which there were no reorientations were called (&apos;deformation bands". At reductions of 60 to 70 pct the elongated cells in the transition bands became sub-bands separated by low-angle tilt boundaries with angles of disorientation of about 2 deg. The elongated cell structure in the deformation band was replaced by a general distribution of dislocations. It was noted that the width of the subbands in the transition bands remained 0.2 to 0.3 µ; i .e., the width of the subbands was the same as the initial cell diameter for reductions up to at least 70 pct. From this, and from considerations of the mechanism of formation of the transition bands,&apos; it was concluded that the subbands evolved directly from the initial cells. In order to check this conclusion, it was decided to examine the relationship between initial cell diameter and width of subbands produced by large rolling reductions. Cell size is known to be dependent upon the temperature of deformation.2,3 However, preliminary experiments with 3 pct Si-Fe crystals indicated that the change in cell size with increasing temperature of deform,ation was not sufficient for the present purpose. On the other hand, cell diameters generally reported for iron deformed at room temperature2&apos;3 range from 1 to 2 p, a factor of 3 to 10 larger than the cells in 3 pct Si-Fe rolled to 10 pct reduction,&apos; indicating the possibility of a marked dependence of substructure (at least in terms of cell size) on the amount of silicon in iron. Thus, the investigation was enlarged to include the study of the effects of varying silicon content on substructure in lightly rolled as well as in heavily rolled crystals of iron and iron with 3, 5, and 6.25 pct Si. The crystals used in this study all had the same orientation, (100)[001], with respect to rolling plane and rolling direction. These were rolled to reductions of from 10 to 97 pct and the substructures determined by electron transmission microscopy in both the rolled state and after annealing. In addition, stress-strain curves were obtained from (100)[001]-oriented crystals of iron and 3 and 5 pct Si-Fe to determine the effect of silicon on tensile properties. The dislocation substructure of the tensile specimens was also determined for Samples pulled to 2 and 10 pct elongation at room temperature for comparison with the substructures produced by rolling. 1) EXPERIMENTAL PROCEDURE Crystals with 3, 5, and 6.25 pct Si were prepared by annealing 0.012-in.-thick sheets of high-purity Si-Fe in purified argon at 1200°C to effect growth

Jan 1, 1965

By Earl S. Bardwell

The structural relations existing between cuprous oxide and copper were first systematically studied by Heynl; who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study of the microstructure could be made to yield a correct estimate of the oxygen content of refined copper. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity. Apparatus.—For the benefit of those who may be unfamiliar with metallographical apparatus and methods and may be interested to know what equipment is required, a few words with regard to the apparatus are in place at this point.

Jan 1, 1914

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961

By R. J. Wagner, Jim Douglas Jr., P. M. Blair

The calculation of the behavior of an oil reservoir during a water flood has long been an important problem to reservoir engineers. Buckley and Leverett derived the differential equation which describes the displacement of oil from a linear porous medium by an immiscible fluid, but this equation could not be solved by the methods of classic mathematics. Consequently, in order to integrate the equation over the length of the reservoir, they neglected the effects of capillary pressure. In the present paper, a numerical method has been developed for determining the behavior of a linear wafer flood with the inclusion of capillary pressure. The differential equation which was derived for the case of incompressible fluids is second order and non-linear. This differential equation was approximated by an implicit form of difference equation which is second order correct in both time and distance. An electronic digital computer was used to perform the numerical solution of the difference equation. INTRODUCTION The problem of calculating the flow and distribution of fluids in an oil reservoir subjected to a water flood has long challenged the reservoir engineer. The ability to solve this problem would provide a valuable tool for the design and study of field waterflooding programs. One of the first contributions in this field was made by Buckley and Leverett,&apos;.&apos; who developed a method of calculating waterflood performance in a linear reservoir. Their technique was limited by the practical necessity of excluding quantitative consideration of capillary pressure. It is the purpose of this paper to describe a method for calculating the behavior of a linear water flood with capillary pressure considered. This method, although limited to the linear case, should serve as a step toward the solution of the two- or three-dimensional waterflooding problem which would better describe actual reservoirs. The treatment of the problem has assumed that the reservoir is linear and homogeneous, that both oil and water -are incompressible, and that gravitational forces may be neglected, and that water is injected into one end of the reservoir and oil and water are produced from the other. Though these assumptions may not be directly applied to natural reservoirs, they are closely approached in many laboratory core tests. The physical problem has been represented mathematically by means of a differential equation and suitable boundary conditions. The inclusion of capillary pressure effects causes the differential equation to be second order and non-linear, and it is not amenable to solution in terms of known functions. Nevertheless, the problem may be solved by numerical methods. The authors have successfully calculated several cases from the start of water injection through to depletion of the hypothetical reservoir using realistic capillary pressure and relative permeability characteristics that were chosen so as to put the method to a test. DIFFERENTIAL EQUATION In two- or three-dimensional problems involving the two-phase flow of incompressible fluids through a porous medium, the equations describing the flow can be combined until only two dependent variables remain, the pressure in one phase, and the saturation of one phase. These variables appear in two simultaneous partial differential equations which are derived on the basis of the conservation of mass and Darcy&apos;s law as applied to two-phase flow. For a linear reservoir, this system of differential equations can be reduced to a single, nonlinear, second order, parabolic differential equation for one dependent variable, the saturation of one phase. For incompressible water and oil, it can be shown that the conservation of mass for the two phases requires that Where q, and q, are the water end oil flow rates per unit cross-section, s, and so their saturations, +, the porosity, and [ and T, dimensional space and time variables. Darcy&apos;s law, as extended to two-phase flow including the effect of capillary pressure,&apos; is as follows:

By Henry Rawdon

ANY laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test, " that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By A. I. Krynitzky, Henry S. Rawdon

The most commonly used material for terminals in spark plugs is commercial nickel wire, because of its relatively high temperature of melting, excellent heat conductivity, and slow rate at which the metal is oxidized, even upon continued heating at high temperatures. The grade commonly used for this purpose averages 97 per cent. nickel, the remainder being manganese, cobalt, iron, copper, with traces of other impurities always found in commercial nickel. A peculiar and interesting type of deterioration that occurs in these nickel terminals during the service life of the spark plug was recently brought to the attention of the Bureau of Standards. Commercial spark plugs vary greatly in their size and shape and the terminals differ considerably as to their relative size, shape, number, and arrangement with respect to one another. Although this defect was studied in detail in only one form of spark plug, the deterioration is a characteristic of the material, i.e., of nickel wire, rather than of the particular type of spark plug in which it was noted and studied. The mechanical features of the plugs, however, have a considerable bearing on the time required for the deterioration to become serious. The results of this study of the deterioration of nickel terminals in service should be of value to the makers of all types of spark plugs in which the terminals are made of this metal. CharacteR of Deterioration of WIres During Service Macroscopic Appearance and Properties of Changed Wire.—The nickel terminals in which the deterioration was studied were taken from spark plugs having a central terminal with the ground or side terminals attached firmly at both ends to the shell of the plug. In some of the plugs, two side terminals were used, one on each side of the central one. Although both terminals were found to have deteriorated to some extent, the attack of the central one was quite negligible compared to that of the side ones. These latter wires had developed, in service, transverse cracks that, in many cases, were as sharp and definite as a knife-cut. After a separation occurred, the breach widened by loss of material from the

Jan 1, 1921

By J. G. Early, F. V. Lenel, G. S. Ansell

The isothermal shrinkage rates of copper-powder compacts were determined in the temperature range from 760o to 1060oC. The rates for compacts fabricated from a pure spherical copper powder were compared, on the one hand, with those fabricated from a spherical powder containing a dispersion of aluminum oxide in the copper matrix and, on the other hand, with those fabricated from a pure copper powder having irregularly shaped particles. The irregular copper-powder compacts shrank much faster than the spherical copper-powder compacts and these, in turn, shrank faster than dispersion -strengthened copper -powder compacts. The experiments were run under a small external load. By varying this load, the stress dependence of the isothermal shrinkage rate could be measured for compacts from spherical-copper powders. This stress dependence was found to be approximately proportional to the 4th (dispersion-strengthened alloys) or 4.5th (pure metals) power of the stress. It is concluded that the material-trans port mechanism is due to dislocation climb rather than to Herring-Naharro creep. In this investigation the isothermal shrinkage rates of compacts made of copper powder with an average particle size of 70 g in the temperature range from 780o to 1060°C were studied. The aim of the investigation was to determine the mechanism of material transport responsible for the shrinkage of these compacts. Since the phenomenon observed in this investigation was shrinkage of compacts at high temperatures, it will be necessary to consider all the material-transport mechanisms possible in sintering. It is unlikely that evaporation and condensation, surface diffusion, or even volume diffusion of vacancies, in which surfaces of small radius of curvature are vacancy sources and those of larger radius of curvature vacancy sinks, will materially contribute to a sintering process involving shrinkage, i.e., one in which the centers of adjacent particles move towards each other. The two principal mechanisms which were considered were the so-called Nabarro-Herring mechanism and a plastic deformation mechanism by dislocation movement. Both of these mechanisms were originally conceived to explain creep, i.e., the plastic deformation of metals at elevated temperatures under a constant applied stress. The shrinking of metal-powder compacts which was studied in this investigation can be readily treated as a creep process. This means that the shrinkage rates observed are considered as creep rates under the influence of an applied stress. It is true that the stresses in sintering experiments are generally not constant but decrease continually with time, but, by considering creep rates or shrinkage rates over a relatively short time interval, the small changes in stress during this time interval can generally be neglected. Nabarro-Herring microcreep is a high-temperature deformation mechanism which is caused by a diffusional flow of vacancies from boundaries under a tensile stress towards those under a compres-sive stress. Herring1 has shown that in this type of microcreep the strain rate e is proportional to the applied stress and follows an equation of the form ma, aexp(-Q/RT) [l| where <j is applied stress, Q is the activation energy for self-diffusion, R is the gas constant, and T is the absolute temperature This type of creep can explain the shrinkage of a porous compact. The surface of the pores are subjected to the tensile stress of surface tension, while the grain boundaries are under a compressive stress also due to surface tension. Vacancies diffuse from the pore surface through the lattice to the grain boundaries, where they are eliminated. In order to maintain vacancy equilibrium at the pore surface the vacancies leaving the region of the pore surface are replenished from the volume of the pore, which means that the pores shrink.

Jan 1, 1964

By Neil H. Bostick

A specialized electronic data system processes data taken from normal gologic maps and stratigraphic tables to yield predictions of uranium resource location for an area such as much of the United States. Strata underlying specific quadrangle cells of the earth are evaluated for uranium favorability on the basis of selected criteria of lithology, structure, and stratigraphy but not specific past production in the area. Stored data are computer processed to yield volume of likely host rock beneath each cell to a given depth and at a given favorobility level. Results are plotted by machine directly as maps. A specialized and simplified procedure for predicting approximate uranium resources has been devised at Stanford Research Institute (SRI). The prediction is based on general geology beneath specific area cells of the earth in order to provide complete volume coverage; the strata underlying these areas are evaluated for uranium mineral favorability on the basis of a few selected geologic criteria in order to allow rapid data input. In order that the predictions be generally applicable, they are based on geological factors only, not past ore production of a given cell. Since the bulk of U.S. resources are in elastic host rocks, only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in an area of the western United States.

Jan 1, 1971

By W. A. Straw

IN the manufacture of telephone apparatus a number of nonferrous sheet metals are blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming, characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper.

Jan 1, 1931

By C. A. Rowland, R. C. Nealey

Until recently there were very few dry grinding rod mills used. The early installations performed as anticipated. In the last seven years a number of dry grinding rod mills have been made, most of which have been used for grinding iron ore. The recent installations have not operated as anticipated in accordance with practices learned from wet rod milling. The paper does not establish any definite rules for the application of dry grinding rod mills but does attempt to establish some guidelines that can be followed. The paper reviews a number of flowsheets describing the problems encountered and some of the solutions found. Completely dried compared to partially dried feed is reviewed. Problems encountered in scaling up from pilot plant to production-size mills are described. Rod sizing, effect of rod length, rod bending, rod breakage, and rod tangling are discussed. While wet grinding rod mills have been used for 50 years to grind ores and make specifications sands, dry grinding rod mills have only recently come into significant use in the mineral industries. Among the materials now being processed in dry grinding rod mills are (1) lead sinter, lead slag, and limestone; (2) iron ore; (3) silica; (4) cement clinker; and (5) coke. Because the application of wet grinding rod mills was well understood at the time that dry grinding rod mills were introduced, the criteria and guidelines for selecting the former were carried over to the selection of the latter - in some cases with the anticipated results, but in many cases not. It is the purpose of this paper to describe, through a series of flowsheets, some of the recent problems encountered with dry grinding rod mills, to point out the solutions to these problems, and to set forth some guidelines for the selection and application of these mills. When dry grinding rod mills came into use, the following facts about their wet grinding counterparts were already well established: (1) The performance of large-sized mills can be accurately predicted from the performance of rod mills 5 or 6 ft in diameter. Wet grinding mills as large as 14 ft in diameter (inside shell) by 20 ft long with rods 19.5 ft long can operate satisfactorily.

Jan 1, 1970