Search Documents

By S. Suphi Yavasca, A. M. Gaudin

THIS paper is intended as a contribution to our knowledge of the mechanism of comminution and of the work of crushing. In a previous paper' it was shown that with quartz comminution proceeds as follows I. The size distribution of broken fragments made by a single fracture is such that the new surface on each grade is the same. 2. Multiple fracturing results in a size distribution such that in the fine sizes the surface per grade is the same in every grade; in coarse sizes the surface per grade decreases gradually with increasing size. In that paper it was mentioned that determinations on minerals other than quartz were in course of completion in order to establish the generality of these observations. In this paper, condensed data2 are presented for galena, pyrite and glass. Galena and pyrite are crystalline material and glass is noncrystalline. Galena has excellent cubic cleavage. Pyrite, although cubical, does not have marked cleavage. Quartz, on which the original determinations were made, does not cleave and although crystalline (hexagonal) breaks conchoidally. Glass breaks much like quartz. It is apparent, therefore, that the minerals selected represent some range in character of the solid without covering all possible types. GLASS Fifteen glass marbles were crushed individually in the pendulum crusher described in the preceding paper,1 then subjected to careful screening for 30 min. Six sized fractions were selected and cleaned in a hot 0.12 N solution of hydrochloric acid, washed with distilled water and dried on a hot plate. This was followed by an examination with a binocular microscope, to remove foreign matters not eliminated in cleaning as well as to eliminate "compacts" of fine particles. These compacts are groups of fine iragments that seem to be mechanically stuck together as a result of localized compacting during the comminution operation. The presence and the abundance of these compacts may be related to the amount and direction of the forces applied in different crushing devices. Since, properly, such compacts should be entirely eliminated in the sizing analyses, it is necessary to remove them to the last before making surface determinations on sized fractions. For example, with a - 28 + 35-mesh glass the surface areas of two samples, one cleaned with acid and under the binocular, the other only washed, were 102 and 172 sq. cm. per gram, respectively. Examination of the samples under an Ultropak microscope showed that washing alone failed to remove the compacts and also that it fails to remove certain fine dusts attached to the particles. Cleaning with acid loosens the fine dusts and

Jan 1, 1945

By Russell G. Wayland

THIS paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. MUSCOVITE MICA Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. THE MICA PROBLEM Block muscovite mica is commercially classified into the following general qualities, beginning with the best quality: I. Clear and Slightly Stained (C & SS). 2. Fair Stained (FS). 3. Good Stained (GS). 4. Stained (S). 5. Heavy Stained (HS). 6. Black Spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately I C & SS to 4 FS to 10 GS to 14 S to whatever the

Jan 1, 1944

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

By R. T. Gallagher

FOLLOWING recent precedent, the Mineral Industry Education Division opened its first session on Sunday afternoon at the Columbia University Men's Faculty Club with an unexpectedly large attendance. The first session was presided over by the Division Chairman, A. F. Greaves-Walker. The first paper, a preliminary report on college enrollments in mineral technology curricula, by W. B. Plank, though incomplete, pointed to a general over-all reduction of 38 per cent in enrollment in mineral industry curricula. Following that, A. C. Callen's paper elicited many comments. It presented the results of a survey (no direct questions asked) addressed to officials in the mining industry. J. L. Bray spoke on war production drive methods and results and his slides gave visible evidence (and much laughter) of the success of the drive. C. L. Wilson's able presentation covered not so much present status but the future status of accelerated mineral technology programs after the war. The last paper of the first session by Edward Steidle, was handed out in mimeographed form.

Jan 1, 1943

By John K. Hammes

INTRODUCTION From the point of view of the consumer, the cost of mineral commodities might be viewed as the total price industry pays for mine output. Similarly, the mining company engaged in the ongoing business of finding, developing and operating new mines is concerned very much today with the distribution of all the revenue paid for mine output and not just with its direct or controllable cash costs. In other words, what will the labor force, the supplier of energy, explosives, and reagents, and the supplier of government services, management, capital, and the ore reserves receive for their contribution to production? A significant amount might be categorized as what economic theory classifies as economic rent. Mining companies are finding it increasingly difficult to negotiate concession or work contracts to develop ore reserves in lesser developed countries, just as they find themselves accused of taking excess profits in their own countries. The principal difficulty in reaching mutually satisfactory agreements in many cases is the difficulty in establishing an acceptable distribution of income, in particular the distribution of economic rent. (See Chapter 7). Further, it is logical that the decisions and policies of the interested parties be they government or industry should be and will be influenced by their competitive position relative to determining the distribution of economic rent. The raising of finance for a mining project today may be inhibited by too biased an extraction of economic rent by entities other than the risk takers, the mining companies. ECONOMIC RENT A British economist (Ricardo D. McGraw-Hill, 1955) first proposed the concept of economic rent (See Drechsler, H.D. earlier in this Chapter.) Ricardo pointed out that no rent would be paid until land became scarce. Ricardo also stressed the distinction that the price of farm produce was not higher because of the rent paid on farm land but that the rent or price of more fertile farm land was higher because the price of produce is higher. This led to the concept that economic rent is not a cost and that it is therefore not price determining, but is itself price determined. Economic rent may be viewed as a cost if cost is equated with the concept of payment or distribution of income to any factor used in production. However, if it is a criterion that a payment must be made to the supplier of the factor of production, then economic rent is not truly a cost because it is not necessarily distributed or "paid" to the supplier. Consider the commodity A which occurs in three grades: Al, A2, and A3. Any grade may be used as a substitute for another grade in all of the industrial uses of A. However, in industries X and Y the different grades have different productivities. Table 1 shows the relative productivities of each grade in industries X and Y, and in all other industries [~]. [ ]

Jan 1, 1985

By Arthur W. Ruff

One of the major challenges to management in the mining industry today is the establishment and maintenance of positive and dynamic programs for cost control and cost reduction. To meet the challenge, management must have a good cost system. There are various types of cost accounting systems in use today: some companies check their, performance by comparing the costs incurred during one period with the costs incurred during previous periods, while others compare the current costs with estimated costs which the company considers desirable. A third type of system is a standard cost system which provides predetermined allowances for the various cost elements and operating activities. Such a system, based on sound standards, can be established to fix responsibility for cost performance in each segment of the operation; recognize the impact of volume or rate of activity by establishing a standard volume and evaluating departures: take into consideration fixed and variable costs and their dissimilar behaviour at varying levels of operations: and provide consistent and equitable yardsticks for measuring performance.

Jan 11, 1962

By Andrew Cosgarea, William R. Upthegrove, Morteza Mirshamsi

The capillary-reservoir technique was used with lead-210 and cadmium-115m to determine the self-diffiLsion coefficients of both cadmium and lead in the liquid binary Cd-Pb system. The self-diffusion coefficients of pure cadmium and pure lead were obtained and were compared with the theoretical predictions. Good to excellent agrement between the experimental and predicted values was obtained. The self-diffusion coefficients of cadmium were tneasuved in alloys containing 2.50, 9.13, 17.40, 31.00, 45.00, 69.00, and 97.00 lot pct Cd by determining- the amount of cadniiutn-115m which diffused out of a small-bore capillavy into an infinite reservoir during- a given time peviod. Sinzila7-measurements were made with lead-210 to determine the self-diffusion coefficients of lead in these identical alloys. Diffusivities were determined from measurenzents performed in the temperature interval of 290" to 480°C. The results were correlated with the Ar-vhenius equation, and the maximum variation of the equation parameters (Q and Do) was also inrestigated . THE theory of diffusion in liquids, particularly liquid metals, is relatively undeveloped in contrast to that for the gaseous and solid states. Although the practical application of liquid metals as heat-transfer media has become increasingly important, few liquid-metals systems have been investigated. Experimental data of fundamental significance in this field are not readily obtained, which may explain but not justify the present lack of knowledge. What work has been completed is primarily restricted to liquid diffusion of pure metals; little work has been done in liquid-metal diffusion of binary mixtures. A review of liquid-metal diffusion theory and research is available elsewhere.1-4 In an effort to add to the knowledge of liquid-metal systems and to increase the basic understanding of the diffusion process in liquids, a study of diffusion in the binary-liquid system, Cd-Pb, was undertaken. The capillary-reservoir technique5 was employed to measure the self-diffusion coefficients of cadmium and lead in molten binary alloys. Measurements were made with seven selected compositions and over a temperature range from 290° to 480°C. The experimental apparatus consisted essentially of the following items: constant-temperature bath, diffusion cells, capillaries, capillary-filling device, and a radioactive tracer counting system. EXPERIMENTAL APPARATUS Constant-Temperature Bath. A cylindrical steel vessel, 8 in. in diam and 15 in. deep, surrounded by an insulated heating coil was used with a sodium-potassium nitrate salt mixture heating medium. The bath was maintained slightly below the desired control temperature by the furnace-heating element; and a 250-w heater, actuated by a Bayley proportional temperature controller, was utilized for the final control of the temperature. A constant-speed mixer stirred the salt to insure a uniform temperature within the bath. Four calibrated Chromel-Alumel thermocouples were placed at various positions in the salt bath to verify the absence of temperature gradients. The observed temperature variation during any diffusion run was less than 0.l°C. The entire furnace assembly was mounted on four shock absorbers to exclude building vibrations and the stirrer propeller blades were adjusted so not to induce vibrations within the reservoir. A schematic diagram of the furnace and the constant-temperature bath is shown in Fig. 1. Diffusion Cell. The diffusion cells and associated parts were the same, except for slight modification, as the one used by walls1 in this laboratory, and are shown in detail elsewhere.' A graphite crucible, 4 in. long and 40 mm (1-1/2 in.) ID, enclosed in a 60-mm (2-1/4 in.) Pyrex tube cell about 18 in. long, was used as a container for the melt. The reservoir (molten alloy in the graphite crucible) was usually about 2 to 2-1/2 in. deep. Graphite was used because of its satisfactory nature as a refractory material and the low solubility of carbon in molten Cd-Pb alloy.677 The Pyrex cell was closed at the bottom and fitted at the top (open end) with a 2-in. Dresser coupling. A brass flange was welded to the top of the coupling. The upper part of the diffusion assembly was bolted to this flange with an O-ring seal. The lower part of the diffusion cell was supported in a 3-in. brass cylinder which was open to allow for circulation of salt around the cell. The top assembly consisted of two synchronous motors, a drive shaft, a thermocouple well, and controlled-atmosphere inlets and outlets. One motor was used for rotation of the capillaries at a rate of 1/2 rpm in the reservoir during the diffusion run. The other motor was used for the vertical positioning of the capillaries and the capillary holder by means of a simple screw drive. The capillary holder and drive assembly were lowered into the reservoir for the run and raised after the desired diffusion time at a rate of approximately 0.4 in. per min. Capillary holders were made of graphite. These

Jan 1, 1967

By G. P. Tiwari

Recrystallization and grain growth in thoria dispersed nickel and nichrome were recently studied by Webster as a function of temperature and deformation. The unexpected part of these results was that specimens which had received heavier deformation developed greater resistance to recrystallization. Retardation of recrystallization was accompanied by the formation of voids around thoria dispersion. To explain these results, Webster suggested that the formation of void around the particles increased the effective size of thoria particles. This resulted in greater impediment to the grain-boundary migration and as a consequence the recrystallization of the matrix is retarded. In the present note an alternative and more probable explanation for the effect of voids on recrystallization is presented. The exact mechanism of void formation in thoria dispersed nickel or nichrome is not known. However, it is reasonably certain that it must be preceded by the stress concentration in the matrix around thoria dispersion during the deformation.'' The resulting stress concentration must be sufficient enough to supply the surface energy for the new surfaces created. Further, the decrease in the strain energy of the matrix surrounding the potential void nucleus must be larger than the surface energy of the newly created surface. The release of strain energy due to formation of crack results in a strain free cylinder of the material around the voids.13 If the void formation is not localized, at few points only (as is the case here), this process may lead to considerable amount of release of strain energy of the matrix. The pattern of recrystallization behavior of single phase homogeneous matrix as well as the matrix having a second phase dispersion is same except for the fact recovery and recrystallization are more clearly delineated.14 In general, the recrystallization temperature is lowered (i.e., recrystallization is easier) with increase in the amount of cold work. This is due to the increase in stored energy in the matrix with increasing amount of deformation. If somehow there is a relaxation of strain energy in the matrix, the recrystallization should become difficult because of the decrease in the amount of stored energy available for recrystallization. Since the formation of voids leads to a decrease in the strain energy of matrix, the recrystallization of the matrix would be inhibited due to the formation of voids during deformation prior to recrystallization. It has been observed by earlier workers15'16 that the presence of preexisting voids in a matrix retards the recrystallization. The essential issue here is how do the voids act to produce this effect. If the voids influence recrystallization only by blocking the grain boundary migration, then the effect should be maximum when they are present almost exclusively along grain boundary. These conditions are obtained during high temperature deformation. However, the voids produced due to creep along grain boundary are not able to prevent recrystallization17 suggesting that they are not effective in blocking grain boundary movement. Recently it was shown by Davies and Williams that the voids can act as sinks for vacancies." As a result the processes dependent on vacancy diffusion like recovery, recrystallization, dislocation climb, and so forth, will be hindered. This fact may be responsible for inhibition of recrystallization during subsequent deformation and annealing cycles. It is to be noted here that there is a large difference between the density of voids in creep experiments and the other experiments where retarding effect of voids on recrystallization is seen. The voids in former may number up to l04 to l05 per sq cm whereas in latter cases the voids density is typically around 1010 to 1013 per sq cm. It appears that the decrease in supply of vacancies in creep is insufficient to adversely affect the recrystallization due to low void population. The author is grateful to P. Das Gupta and S. P. Ray for helpful discussions. Author's Reply D. Webster Tiwari appears to have misunderstood the nature of grain boundary-particle interactions. Tiwari (quoting Cahn) states that second phase particles become more effective as they become smaller, therefore as the voids in TDNiC make the thoria particles effectively bigger their ability to resist grain boundary movement is impaired. This particle size argument was originally proposed in the form of an equation by Zener 20 years agol9 and is not necessarily valid as is discussed below. However, assuming it is valid, it predicts a greater boundary restraining effect by smaller particles simply because their combined cross sectional area is greater at a constant volume. If the number of particles remains the same and their effective size increases, as in the present case, Zener's equation predicts a greatly reduced grain size. This is because the effect

Jan 1, 1970

By William H. Bassett

COPPER is the world's most important non-ferrous metal, and brass is the most widely used non- ferrous alloy. Much of the utility of each may be credited to the work of metallurgists who have constantly improved the quality of the metals and alloys and the methods of fabrication. Standing in the front rank among these is William Hastings Bassett, the newly elected president of the Institute. Mr. Bassett, ,who is technical superintendent and metallurgist for the American Brass Co.,

Jan 1, 1930

By J. R. O’Connor

Stimulated emission from Nd+3 in yttrium uanadate fYVOJ is reported. Single crystals of YVO4:Nd, obtained from Linde Col-p., have improved substantially in the last several months. Pulsed thresholds of YVO, laser rods are now approximately 2 to 3 5, cowparable to tliose for YAG:Nd. Yttrium uanadate crystalli~es irz a space group similar to zircon. All rare-earth vanadates have this structure. Rare-earth ions sucll as Nd+3 which substitutes for Y+3, aye situated irz a strong tetragonal crystal field which lacks inversion symmetry. This condition increases the p'robability of the parity-forbidden f — f transitions. Yttrium anadate has strong absorption bands beyond -1000A. These are clue to Y-O, V-O charge transfer and molecular transitions. Under 2537 and 3660A irradiation pure YVO, fluroresces u bright yel-LOLO. This fli&orescence is corrzpletely quenched in YV04:Ncl crystals. This and other evidence of energy trut~sjer from the lattice is repovted. Optzcul atz 1user pvope 1-ties o! YI'U4:E[t are brieJy described. THIS paper describes some of the optical and laser properties of Nd+3- and Eu+3-doped yttrium orthovana-date (YVO4). It reports laser action for the first time in this low-symmetry host. For some time we have pursued a research program concerning laser hosts' wherein the rare-earth (RE) ion is situated at a site of low crystal symmetry so as to increase the probability of radiative transitions. Single crystals of doped and undoped YV04 are grown from iridium crucibles in an oxyhydrogen gas-fired furnace by a modified Czochralski technique.' This material crystallizes in a D4li tetragonal space group of the zircon (ZrSiO,) type.3 All RE vanadates have the same structure and form solid solutions with YVO4. Therefore, it will be possible to investigate a variety of cross-pumped laser systems, as in the case of yttrium aluminum garnet (YAG).4 At present, ~d'~-doped YAG is one of the most efficient solid-state lasers.5 Accordingly, most of the material to follow will compare the properties of YV04 to those of YAG. Fig. 1 shows the relative transmission of YAG and two types of YVO4. "Pure" YVO4 has a normal absorption edge and is colorless. A second type has a broad absorption peaking near 4200A and is yellow. Rubin and Van uitert6 suggest the yellow material is slightly reduced. Samples of each type are being investigated by electron spin resonance,7 but these studies are so far inconclusive. The pulsed laser threshold is much lower in the yellow material than in the colorless. Therefore, the absorption at 3500 to 5000.4 transfers energy to the Ndi3 ions. Photons of wave length between 2000 and 4500A cause undoped YVO4 to fluoresce at 4800, 5250, 5460, 5540, and 5750A. This emission, previously reported by Brixner and Abramsom,8 is partially quenched by EU'~ and completely quenched by Ndt3 at room temperature due to energy transfer from the lattice to the RE ions. At low temperatures, some lattice fluorescence is present. This implies that the energy-transfer process is in part phonon-assisted. Although the YVO, single crystals used in this work were prepared from Y2O3 containing less than 0.01 pct rare-earth impurities, there is aopossibility that emission lines between 4800 and 5750A are due to dysprosium, terbium, and so forth. However, these lines are not observed in other compounds, prepared from Y2O3, such as YP04, Y2MoO6, and so forth. Furthermore, extensive absorption measurements on our "pure" YV04 single crystals between 0.4 and 5.0 failed to reveal any characteristic rare-earth lines. Fig. 2 compares the absorption spectra of Ndt3-doped YAG and YVO4from 0.6 to 1.0 . The Ndt3 absorptions are labeled according to free ion, R-S coupling. These term designationsQ are appropriate for YAG:Nd. They appear to be inappropriate for YV04:Nd. In YVO, neodymium must substitute for yttrium. The yttrium site is situated In a strong tetragonal field, where point symmetry is (42m) or possibly lower.1° However, the reduced splitting of the Stark components of the YV0,:Nd spectrum implies that the NdT3 ion is in a cubic site. The only plausible explanation for this discrepancy is that the Ndt3 ion is in a low-symmetry site, lacking inversion symmetry, so that a substantial admixture of 4f and 5d wave functions occurs. In this case, R-S coupling is not valid and J is no longer a good quantum number." Consistent with this view, the 4~ metastable level of YV04:Nd has an oscillator strength larger and a

Jan 1, 1968

By J. D. Miller, J. E. Sepulveda

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence' gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource. The projected increase in the ever-widening gap between the domestic energy demand and the domestic energy supply for the next few years has motivated renewed interest in energy sources other than petroleum, such as tar sands, oil shale and coal. Although a number of research programs on the exploitation of national coal and oil shale resources have already been completed, very few programs have been initiated on the processing of tar sand resources in the United States. In recognition of their significance as a domestic energy resource, investigators at the University of Utah have designed an extensive research program on Utah tar sands. An important phase of this program, and the main subject of this publication, is the development of a hot-water process for the recovery of bitumen from Utah tar sands, as a preliminary step toward the production of synthetic fuels and petrochemicals. The term "tar sand" refers to a consolidated mixture of bitumen (tar) and sand. The sand in tar sand is mostly a-quartz as determined from X-ray diffraction patterns. Alternate names for "tar sands" are "oil sands" and "bituminous sands." The latter is technically correct and in that sense provides an adequate description. Tar sand deposits occur throughout the world, often in the same geographical areas as petroleum deposits. Significantly large tar sand deposits have been identified and mapped in Canada, Venezuela and, the United States. By far, the largest deposit is the Athabasca tar sands in the Province of Alberta, Canada. According to the Alberta Energy Resources Conservation Board (AERCB),2,3 proved reserves of crude in-place bitumen in the Athabasca region amount to almost 900 billion bbl. To date, this is the only tar sand deposit in the world being mined and processed for the recovery of petroleum products. Great Canadian Oil Sands, Ltd. (GCOS) produces 20 million bbl of synthetic crude oil per year. Another plant being constructed by Syncrude Canada, Ltd. is expected to produce in excess of 40 million bbl of synthetic crude oil per year. According to the Utah Geological and Mineral Survey (UGMS), tar sand deposits in the state of Utah contain more than 25 billion bbl of bitumen in place, which represent almost 95% of the total mapped resources in the United States.4 The extent of Utah tar sand reserves seems small compared to the enormous potential of Canadian tar sands. Nevertheless, Utah tar sand reserves do represent a significant energy resource comparable to the United States crude oil proved reserves of 31.3 billion bbl in 1976.5 Tar sands in Utah occur in 51 deposits along the eastern side of the state.4 However, only six out of these 51 deposits are worthy of any practical consideration (Fig. 1). As indicated in Table 1, Tar Sand Triangle is the largest deposit in the state and contains about half of the total mapped resources. Information regarding the grade or bitumen content of Utah deposits is still very limited. The bitumen content varies significantly from deposit to deposit, as well as within a given deposit. In any event, the information available6-8 seems to indicate that Utah deposits are not as rich in bitumen as the vast Canadian deposits which average 12 to 13% by weight.9 Although many occurrences of bitumen saturation up to 17% by weight have been detected in the northeastern part of the state (Asphalt Ridge and P. R. Spring), the average for reserves in Utah may well be less than 10% by weight. Separation Technology As in any other mining problem, there are two basic approaches to the recovery of bitumen from tar sands. In one

Jan 1, 1979

By O. Hoover, M. Herman, V. V. Damiano

The Jetter and borie' teclznique of determining textures using a spherical specimen has been applied to tlze study of compression-rolled beryllium sheet. Snzall spheres the order of 1 mm in diam cut from the beryllium sheet were autotnatically rotated about tz41o axes using the G.E. single-crystal goniometer. Quantitative pole figures were obtained without tke need to apply absorption corrections. Compression-rolled beryllium exhibited peak intensities ,for (0002) planes of positions tilted 10 deg to the rolling plane and a near random distribution of (1010) planes about the nornal to the rolling plane. TECHNIQUES for determining textures of rolled sheet material are amply described in the literature. The techniques are found to be variations of two basic methods. One due to Decker, Asp, and arker, referred to as the transmission method, utilizes a thin-sheet specimen in which the X-ray beam enters the specimen from one side and the intensity of the beam which emerges from the opposite side is measured. The second method due to chulz,3 referred to as the reflection method, utilizes a thick specimen and the intensity of the beam emerging from the same side is measured. The two rotations of the specimen in the beam are designated a and 8. In order to completely determine the texture of sheet material, it is generally necessary to use a combination of the two methods. The calculations involved in correcting the raw X-ray data for absorption effects and the combining of the data obtained by the two methods are very laborious and time consuming. To avoid the intensity corrections which arise as a result of the changing diffraction volume and path length within the sample other methods have been proposed. The Norton method utilizes a cylindrically shaped specimen cut from the sheet material. Since the rods have rotational symmetry, the absorption correction is constant for rotations about the sheet texture. Jetter and Borie' employed a spherical specimen to analyze the fiber texture of extruded aluminum rods. The spheres were rotated rapidly about the fiber axis to include a large number of grains in the X-ray beam and changes in intensity with respect to tilts of the fiber axis were measured. The absorption correction was constant for all angles and was neglected. The Jetter and Borie' technique finds excellent ap- plication to very fine-grained low-absorbing metals in which the entire sphere volume can contribute to the diffraction volume. In the case of low-absorbing metals, however, serious limitations on specimen thickness occur as demonstrated by Braggs due to de-focussing effects. Peak shifts may occur which negate the assumption that integrated intensities are proportional to peak intensities. These limitations in sphere size to the order of 0.5 to 1 mm for beryllium require that the grain size be sufficiently small to include a large enough statistical sample. The present paper describes the application of spherical specimens less than 1 mm in diam to the quantitative determination of pole figures for compression-rolled beryllium sheet having a grain size the order of 10 p. EXPERIMENTAL 1) Specimen Preparation. Two techniques for spark-machining beryllium spheres were tried. One involved the use of a hollow cylinder as a cutting tool. The tool was fed into the rotating cylindrical specimen as shown in Fig. l(a). The hollow cylinder was carefully aligned such that the axis of the cylinder and the axis of the specimen lay in the same plane and were 90 deg to each other. As the hollow cylinder was fed into the rotating cylindrical specimen, a spherical shape was formed as shown in Fig. 1. Alignment was very critical. Slight misalignment resulted in the formation of a barrel-shaped specimen instead of a sphere. A second technique involved the use of a cutting wheel shaped as shown in Fig. 2 with a groove of the desired radius. A section of the sheet specimen was first turned into a cylinder on the left part of the cutting wheel. It was then shifted to the right and a spherical specimen was turned as shown in Fig. 2. The axis of the cylinder lay in the plane of the sheet. Flats corresponding to the rolling plane of the sheet were used to grip the specimen during the machining operation and these served to identify the rolling plane of the sphere. 2) Rotation of Spec=. The spherical specimen is shown mounted on the G.E. single-crystal goniometer in Fig. 3. The knob A of the goniometer shown in Fig. 3 rotates the specimen about the pedestal axis. These angles have been designated as @ angles. The knob B rotates the specimen about an axis perpendicular to the pedestal axis. These angles have been designated as p angles. A device was made to automatically drive the single-crystal goniometer by means of two flexible shafts connected to the A and B knobs as shown in Fig. 3. The motor system was designed to rotate the knob A, thus rotating the specimen through angles of $I while the B knob remained stationary. After one complete

Jan 1, 1967

By K. G. Wikle, W. W. Beaver

The factors which control the rate of dissolution of pure gold in cyanide solution were studied both directly and through measurement of solution the current-potential curves for the anodic and cathodic portions of the reaction. The mechanism of dissolution is probably electrochemical the reaction in nature, and the rate is determined by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on their relative concentrations. The significance of the results and the effects of impurities are considered. ALTHOUGH the dissolution of gold in aerated cyanide solutions has been used as an industrial process for treatment of gold ores since the late nineteenth century, the factors which determine the rate of the reaction have never been identified unambiguously. Studies of the rate of dissolution by Maclaurin,1 White,2 Christy,3 Beyers,4 Thompson,6 and others are contradictory in their conclusions; some claiming that diffusion of the reactants to the gold. surface controls the rate, and others that the chemical reaction is inherently slow and related to high activation energy for the reaction. Christy3 and 'Thompson" both suggest that the reaction is electrochemical in nature and that the dissolution of gold proceeds at local anodic regions while the oxygen is reduced at cathodic regions on the gold surface. Although their studies are ingenious and do indicate an electrochemical reaction under the conditions of study, their experiments were of limited nature and failed to identify the rate-controlling process in the system. The importance from an industrial viewpoint of a knowledge of the mechanism and rate-controlling factors in gold dissolution can be illustrated as follows: If the rate is controlled by a slow chemical reaction rather than by diffusion of the reactants, then an increased temperature should have a marked accelerating effect; agitation of the slurry should have no effect on rate: and increased concentration of reactants should cause acceleration of the rate. If the rate is controlled by the diffusion of one or the other of the reactants to the gold surface, then increased agitation should increase the rate; increased temperature will increase the rate, but not as much as for the case of a slow chemical reaction; increased concentration of the reactant which is diffusion limited will increase the rate; and the concentration of other reactants should be without effect on the rate. It may be concluded that for design of a commercial process for gold leaching, the rate-controlling factors of the reaction should be understood so that an intelligent choice of the conditions of agitation, temperature, and reactant concentration may be made. The experiments described here lead to the unambiguous conclusion that in a system of pure gold and a pure aerated cyanide solution the rate of dissolution is controlled either by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on the relative concentrations of each. There is also ample, but not conclusive, evidence that the mechanism of the reaction is identical to that of electrochemical corrosion. The practical significance of these conclusions will be discussed later in the paper. Experimental The experimental method used in this work was to employ an electrolytic cell which performed the overall gold-dissolution reaction, and to study the anodic and cathodic reactions of this cell as to their nature and the rate-controlling factors. Simple experiments on the rate of dissolution and the potential of the dissolving specimen also were performed under conditions of agitation, temperature, and concentration identical to those used in the electrode studies. Analysis of the electrode studies by well established theories of electrochemical corrosion were made, and the results were found to bear a one-to-one relation with actual rate and potential measurements. Electrode Studies: The Anodic Reaction: The gold specimen used for all of the electrode studies and the rate determination consisted of a sheet of 99.99 + pct Au wrapped around a lucite rod and sealed at the edges with plastic cement, thus forming a cylinder of gold of known and constant area (8.0 sq cm). The lucite rod was threaded into a brass spindle which could be rotated at speeds of 100, 300, and 500 rpm. For the electrode studies electrical contact between the gold cylinder and the brass spindle was made by means of a gold strip covered with plastic. The anodic dissolution of gold was studied by immersing the electrode in a solution containing known concentrations of KCN and KAu(CN)2 but free of oxygen, and by passing an anodic current through the gold electrode. The pH of the solution was maintained between 10.5 to 11.0 in these and all other tests by addition of KOH. The pH was measured before and after each test by means of a glass-elec-

Jan 1, 1955

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By T. A. Read, M. S. Wechsler, D. S. Lieberman

A theoretical analysis of the austenite-martensite transformation is presented which predicts the habit plane, orientation relationships, and macroscopic distortions from a knowledge only of the crystal structures of the initial and final phases. THIS paper presents a new theory of the formation of martensite. This theory makes possible the calculation of the austenite planes on which the martensite plates form, the orientation relationship between the austenite and martensite crystal axes, and the macroscopic distortions which are observed. The only input data needed are the crystal structures and lattice parameters of the austenite and martensite. Considerable effort has been devoted over the past thirty years to the development of an understanding of the crystallographic features of martensite reactions. Much of this work has been done on steels and iron-nickel alloys, for which a great deal of data has been accumulated concerning the shape and orientation of the martensite plates, the relative orientations of the austenite and martensite crystal axes, and the observable distortions which result from transformation. These observations are reviewed in refs. 1, 2, and 3. The first major step toward an understanding of these phenomena was made in 1924 by Bain,&apos; who showed that the a body-centered cubic structure can be produced from the 7 face-centered cubic structure by a contraction of about 17 pct in the direction of one of the austenite cube axes and an expansion of 12 pct in all directions perpendicular to it. Since that time, most of the efforts at further interpretation have been made by investigators who have worked from the phenomenological data, incorporating some of the information from the lattice properties, and have sought an analysis into likely deformations which would produce the observed results."- "11 but the three most recent papers on the subject have already been reviewed in some detail." Machlin and Cohenl0 measured the components of the distortion matrix and verified that the habit plane is a plane of zero distortion and rotation for the (259) case. They showed that the measured distortion matrix, when applied to the parent lattice, does not yield the product lattice and hence some inhomogeneous distortion must occur. Frank,u working from the lattice properties and taking some clues from the observations, considered the correspondence of close-packed rows and planes in the austenite and martensite. He predicted substantially the observed lattice relationship and habit plane for certain steels which have a (225) habit. Geisler12 suggested that there is a natural tendency for the habit plane to be a (111) and postulated certain slip processes to account for the fact that the experimentally observed habit plane is irrational and deviates from the assumed one. The present work differs from previous treatments of martensite formation in that it permits calculation of all the major manifestations of the process. Habit plane indices, orientation relationships, and observable distortions are all calculated from a knowledge of the crystal structures of the initial and final phases alone. The calculations contain no adjustable parameters. The agreement found between calculated results and the observations reported in the literature constitutes powerful evidence in favor of the mechanism of martensite formation proposed. The theory is applicable to systems other than steel (as is discussed later in this paper) which exhibit a diffusionless phase change but because of the wide-spread interest in the austenite-martensite transformation, particular attention will be given to the iron-base alloys. For other systems which undergo a similar face-centered cubic to face-centered tetragonal transformation, the mathematical treatment is identical with that presented here. Hence the theory successfully describes the transformation in the indium-thallium alloy.&apos;" Homogeneous Transformation to Martensite The distortion which any homogeneously transforming volume of austenite undergoes in order to become martensite is shown in Fig. 1, as was first suggested by Bain.&apos; (This distortion will hereafter be referred to as the "Bain distortion.") This specification of a contraction along one cube axis ;ombined with an expansion in all directions perpendicular to this axis describes what is properly called the "pure" distortion associated with this transformation. The distinction between a "pure" and an "impure" distortion plays an important part in the discussion which follows. A "pure" distortion is characterized by the existence of at least one set of orthogonal axes fixed in the body which are not rotated by the distortion. (These are called the "principal axes" of the distortion.) No such set of axes exists in the case of an "impure" distortion. On the other hand, an impure distortion can always be represented as the result of a pure distortion combined with the rotation of the specimen as a rigid body. For a given impure distortion the corresponding pure distortion

Jan 1, 1954

By A. S. Venkatadri, H. B. Bell

The equilibrium sulfur distribution between molten iron and Ca0-Mg0-Al203 slags containing iron oxide was investigated at 1550°C. The results were used to derive the iron oxide activities at low iron oxide concentrations in the slag by combining the sulfide capacity data obtained from gas-slag work with the free energies of both the sulfur solution in iron and the iron oxide formation in slag. The derived ferrous oxide activities were compared with values based on Tem-kin&apos;s kin&apos;s and Flood&apos;s ionic models. One difficulty in using these models is that the nature of the aluminate ion in slag is uncertain. Nevertheless, such indirect methods, in particular, those described in the present paper, are of value because of the difficulty of measuring small amounts of oxygen in liquid iron in equilibrium with slag. It is shown that these methods confirm the consistency of thermodynamics data on liquid iron and slags. It is well established that decreasing the iron oxide activity in the slag increases the desulfurization of molten iron at constant slag basicity. This effect is most pronounced at the very low iron oxide activities, characteristic of blast furnace slags. Yet a precise quantitative determination of the significance of low iron oxide contents in slag in blast furnace desulfuri-zation is not possible for the following reasons: a) difficulty of separation of iron "shots" from the slag, and b) errors in chemical analysis of small amounts of iron oxide in slags. In view of these obstacles, one must resort to indirect methods of calculating iron oxide activities. EXPERIMENTAL TECHNIQUE The apparatus for providing the sulfur equilibrium data has been described previously1 and was similar to that used by ell&apos; in connection with the study of slag-metal manganese equilibrium. The procedure consisted of: a) melting about 50 g of Armco iron in a magnesia crucible in a platinum furnace, b) adding a mixture of about 15 g of lime-alumina slag and varying amounts of Fe2O3 and CaS, and c) maintaining the temperature at 1550°C for more than an hour in an atmosphere of argon to enable the sulfur equilibrium to be attained. Several melts were made using lime-alumina slags with basic composition 55, 50, and 45 pct lime. During the experiment the temperature was controlled manually using a Pt/10 pet Rh-Pt thermocouple. After the experiment, the Power was shut off and the flow rate of argon was increased to freeze the melt as quickly as possible. The analysis of sulfur in the metal was carried out by the oxygen combustion method3 using uniform drillings from the top and bottom of the metal button. After crushing and grinding and removal of any iron particles with the aid of a hand magnet, the slag was analyzed for sulfur by the CO2 combustion method.4 The E.D.T.A. method was employed for the analysis of lime5,6 and magnesia,= the ceric sulfate method7 for the analysis of slag iron oxide, and the perchloric acid dehydration method5 for the analysis of silica. The remaining amount was taken to be Al2O3 precipitation with ammonium hydroxide in several preliminary melts had confirmed the propriety of using this simple procedure. RESULTS The activity of iron oxide in binary, ternary, and more complex slags has been the object of numerous investigations, and the two experimental methods for its determination are: 1) Equilibrating the metal with the slag in question and measuring the oxygen content of the metal. The ferrous oxide activity is then given by aFeO L%OJSat where [%0]sat is the oxygen content of the metal in equilibrium with pure iron oxide slag. This method was used by Chipman et al.8,9 2) Equilibrating the slag in iron crucibles with known partial pressures of H2/H2O or CO/CO2 mix-tures.10-12 This method is limited to temperatures between 1265" and 1500°C. The very low oxygen content of the melts in this investigation made it impossible to derive the ferrous oxide activity by the first of these methods. Therefore, the iron oxide activities were computed by means of: Sulfide capacity data from the gas-slag work" Temkin&apos;s concept14 Flood&apos;s approach15 a FeO from Sulfide Capacity. The method of calculating the aFeO involves the sulfide capacity of the slag (c,), the sulfur distribution coefficient (Ls), the free energy of dissolution of sulfur in iron, and the free energy of formation of iron oxide in the slag. Bell and Kalyanram13 have investigated the sulfur absorption characteristics of lime-alumina slags containing magnesia by the Carter-Macfarlane method16 (based on comparing the sulfide capacity of the slag in question with that of a standard slag of unit lime activity) and have derived lime activity values. The relation between sulfide capacity and their lime activity a&apos;CaO is given by: Cs= 3—: Xa&apos;CaO at 1500°C

Jan 1, 1970

By Robert K. Waits

The resistivity, temperature coefficient of resistance, stability at 200°C, and structure of annealed Si-Cr films have been studied as a function of film cowposition. Colorimetric analyses of the films indicated 20 to 60 wt pct Cr over the resistivity range of 1 to 10-4 ohm-cm. Resistors were delinealed by photolithographic etching, contacted with aluminum, and mounted in TO-5 packages. The average temperature coefjicient of resistance, a, between 50" and 150°C is related empirically to the film resistivity, p, by a (ppm per °C) = -2900 - 1140 log p (ohm-cm). Near a resistivity of 3.5 x 10-3 ohm-ctn (30 at. pct Cr) , the temperature coefficient changes from positive to negative. The temperature at which the resistance maximum occurs increases with decreasing resistivity. The conduction mechanism between —196" and +360 C appears to have two components—an activated conduction dominating a1 lord chromium content and higher temperatures and a linearly temperature-dependent conduction dominating at high chromium content and low temperatures. Electron diffraction patterns showed the films to consist of Cr3Si and amorphous silicon. Resistors thicker than 150A typically drifted less than 0.6 pct after 5000 hr stor-age at 200°C. Resistors as thin as approxinzately 80°A that had a silicon overlayer showed similar stability. Such films had sheet resistivities of 10 kilohm per square and temperature coefficients near —600 ppm per "c. THIN-FILM resistors having sheet resistivities greater than 1 kilohm per square are required in many integrated circuit applications. A process for producing such resistors should be compatible with present circuit fabrication and packaging, including exposure to maximum temperatures of 300° to 570°C during contact alloying, die-attach, and ceramic package sealing. In addition, the resistors should have a low temperature coefficient of resistance and change less than 1 pct during storage at temperatures up to 200°C for 1000 hr or longer. Reports of work beginning in 1949 at Battelle Memorial Institute indicated that, among other materials, the silicides of chromium, Cr-Co, molybdenum, tantalum, and tungsten were worthy of further study as high-stability resistive films. Later work on Si-Cr films vacuum-deposited by flash evaporation from a tungsten boat1 led to the conclusion that Si-Cr had "excellent properties for development into high- stability ... resistive elements". More recently, Si-Cr films have been vacuum-deposited from a tantalum boat,2 from a BeO-coated tantalum boat,3 by flash evaporation from an electron-beam-heated tungsten Source,4 and by triode sputtering.5 This paper describes a study of Si-Cr films vacuum-deposited by electron-beam heating of Si-Cr alloys. Resistivity, temperature coefficient of resistance, stability at 200°C, and structure were studied as a function of film composition. EXPERIMENTAL PROCEDURE Film Deposition. Si-Cr sources were prepared by vacuum-melting pressed pellets of mixtures of powdered chromium (99.9 pct, -100 mesh, Lunex Co., Pleasant Valley, Iowa) and silicon (99.99 pct, -325 mesh, United Mineral and Chemical Co., New York). A permanent-magnet focused electron-beam gun having a water-cooled copper crucible was used to heat the pellet until complete melting occurred. The mixture was then kept molten for an additional 5 min. The alloy thus formed was used as the source material for Si-Cr film depositions using the same electron-beam gun. Pieces of semiconductor-grade silicon ingots were used as sources for silicon depositions. The films were deposited within a standard vacuum evaporator having an 18-in.-diam Pyrex bell jar, a liquid-nitrogen-cooled trap, and a Consolidated Vacuum Corp. 6-in. diffusion pump containing Dow Corning DC-705 pump fluid. The substrates were thermally oxidized* silicon wafers 2 to 2.5 cm in diam. The

Jan 1, 1969

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase &apos;fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,&apos; hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.&apos; It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

I HAVE previously shown you in the Fifth Book the process of making guns and gun carriages, together with other preparations and methods of moving them. If I now failed to show you more about them, it would be as if I had pointed out only the useless shadow of a thing, for I did not show the kinds and arrangement of their supplies or how the effects for which they are made are achieved. For these reasons I now wish to tell you, in addition to what I have already said, how saltpeter is made and the methods of refining it well; what it is and how without it guns and many effects of violent and artificial fires would have been discovered in vain. After this, I also wish to tell you the methods of compounding the powders for large and small guns, and finally how these are loaded and discharged. I also wish to tell you how mines are made, and fire tubes, [149v] fire pots, squibs, fireballs, rockets, shells, grapeshot, and other similar devices for shooting fire in order to bum ships, supplies, bridges, and ramparts, or, in offense, for firing on batteries. I also wish to teach you to make certain bronze balls for shooting, which carry fire and break in many pieces when they hit. For surely, besides being terrifying to the sight, they would be harmful to armies lined up in battle when they are fighting. Likewise, I wish, to enlighten you as to how artificial fires are made that last long and are difficult to extinguish. Since these are fine and useful things in wars, every captain and soldier should give them consideration and know how to use them when necessary. You will be pleased to have this information if for no other reason than that you can teach it to those who take delight in celebrating holidays with festivities and with fires.

Jan 1, 1942

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963