Search Documents

By R. I. Jaff, H. R. Ogden, D. J. Maykuth

A phase diagram for alloys containing from 0 to 66.9 pct Mn was determined. Two compounds, tentatively labeled 6 and y, were found in this range. The 6 compound is located at about 66.9 pct Mn and melts congruently at 1330°C. The ? compound has a composition near 53 pct Mn and originates in a peritectic reaction at 1200°C between liquid and 6. ß and Y enter into a eutectic reaction at 1175°C. The ß phase field terminates in a very sluggish eutectoid reaction between a and ? at 550°C. MANGANESE is one of the important alloying addition elements to titanium. As a ß-stabiliz-ing addition for a-ß and ß alloys, it provides high strength with adequate ductility.' Two of the earliest commercial alloys contain manganese as a major alloying component.' The earliest published data on the constitution of Ti-Mn alloys was that of Wallbaum,~ who reported the existence of the compound TiMn2. The transformation range of commercial-purity Ti-Mn alloys was investigated by Craighead, Simmons, and Eastwood' who found limited a solubility and a lowering of the ß transus to about 790°C at 7 pct Mn. Preliminary work by the authors of this paper, using high-purity titanium, confirmed the ß-stabilizing action of manganese and showed the existence of several intermediate phases in the Ti-Mn system." More recently, McQuillan3 determined the ß transus temperatures for high-purity Ti-base alloys containing up through 4.4 pct Mn. These data are given in Fig. 1. The present investigation covered alloys made with a high-purity base. The constitution of titanium-rich alloys made with commercial titanium has been reported4," by Holladay, Kura, and Jackson. The alloy range covered in the present investigation was from 0 to 69.5 pct Mn. This alloy range extends slightly beyond the composition of the first congruent-melting compound encountered on proceeding from the titanium end of the system. A description of the materials and methods used in the determination of the diagram is given in the Appendix. The partial phase diagram determined for the Ti-Mn system is shown in Fig. 2. Details on equilibria in the titanium-rich alloys are given in Fig. 3. Liquid-Solid Relationships Observations on the cast structures of the arc-melted ingots showed that the terminal solid solution of manganese in ß titanium enters into a eutectic reaction with an intermetallic compound labeled ?. As will be shown later, this compound has a composition around 53 pct Mn. The eutectic reaction temperature was determined as 1175°C by thermal analysis which also showed that the ? phase originates in a peritectic reaction at 1200°C. Fig. 4 shows typical eutectic structures for alloy compositions on both sides of the eutectic composition which is located at 42.5 pct Mn. In alloys over the range of 45.4 through 69.5 pct Mn, a second intermetallic compound, labeled 6, was identifield as the primary phase. This phase consistently increased in amount as the manganese content approached 66.9 pct, and, as shown in Fig. 5, an alloy structure containing 66.9 pct Mn consisted essentially of the 6 compound. Thermal-analysis data indicate a melting point of about 1330°C for the 6 intermediate phase. At 67.0 pct Mn, small quantities of a new, higher manganese-content phase were observed in the form of Chinese-script eutectic particles. Comparison of Fig. 6a and b shows an increasing quantity of this phase as the composition was increased to 69.5 pct Mn. The formation of peritectic ? in arc-melted alloys containing 45.4 pct Mn and above appears to be almost entirely suppressed, as shown in Fig. 7a and b. This is because of the narrow freezing range available for its formation by peritectic reaction and because of the very high cooling rates obtained in

Jan 1, 1954

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By Paul Weaver

DURING 1932 the amount of geophysical surveying carried out as a part of oil-field development in¬creased, particularly in the Gulf Coast of Texas and Louisiana. Here the most intensive geophysical activity was displayed in the discovery of domes and prospects several years ago, after which there was a period of relative inactivity. This year many of the leases required development and geophysical methods were used to obtain pictures of the detailed structures. These were almost exclusively gravity and reflection-seismograph surveys and for the first time this latter method was generally used by oil operators to construct subsurface contours. The total number of geophysical troops in this territory increased from 16 to 40 during the year.

Jan 1, 1933

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman&apos; reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser&apos; reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,&apos; values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,&apos; on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.&apos; When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,&apos; appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.&apos; For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,&apos; polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By R. K. Dann, L. W. Roberts, R. B. Benson

The mechanical properties of 300-series stainless steels were investigated in both high-pressure hydrogen and helium environments at ambient temperatures. An auslenitic steel which is unstable with respect to formation of strain-induced a (bee) and € (hcp) mar-tensile is embrittled when plastically strained in a hydrogen environment. A stable austenitic steel is not embriltled when tested under the same conditions. The presence of hydrogen causes embrittlement at the mar-lensitic structure and a definite change in the general fracture mode from a ductile to a quasicleavage type. The embrittled martensitic facets are surrounded by a more ductile type fracture which suggests that the presence of hydrogen initiates microcracks at the martensitic structure. If a steel is unstable with respecl to fortnation of strain induced martensile, plastic deformation in a hydrogen environment will produce rapid embrittlement of a notched specimen in comparison to an unnotched one. FERRITIC and martensitic steels can be embrittled by hydrogen that has been introduced into the alloys, either by thermal or cathodic charging prior to testing.1-5 However, conflicting reports exist as to whether austenitic steels that are stable or unstable with respect to formation of strain-induced martensite can be embrittled by hydrogen.8-12 A recent investigation has shown that cathodically-charged thin foils of a stable austenitic steel can be embrittled.13 An earlier investigation of a thermally charged 18-10 stainless steel revealed a significant decrease in the ductility only at the lowest test temperature of -78°C, although strain-induced bee martensite was shown to be present in one specimen tested at ambient temperatures.&apos; When martensitic steels are tested in a hydrogen atmosphere, they are embrittled.&apos;4-&apos;7 It has been observed in this Laboratory that 304L steel, which is unstable with respect to formation of strain induced martensite, forms surface cracks when plastically strained in a high-pressure hydrogen environment. Work in progress elsewhere concurrent with this investigation has also established that 304L is embrittled when tested in a high-pressure hydrogen atmosphere." The objective of this investigation was to study the effect of a high-pressure hydrogen environment on the tensile properties of a stainless steel that contained strain-induced martensite (304L) and one that did not (310). EXPERIMENTAL TECHNIQUES Notched and unnotched cylindrical specimens were machined from 304L* and 310 rods that were heat- treated at 1000°C in argon for 1 hr followed by a water quench. The chemical analyses of these steels are given in Table I. The unnotched specimens had a reduced section diameter of 0.184 & 0.001 in., a gage length of 0.7 in., and were threaded with a 0.5-in.-diam. thread on each end. The notched specimens had a reduced section diameter of 0.260 * 0.001 in. and a 0.75-in. gage length, with a 30 pct 60 deg v-notch at the center. The notch had a maximum root radius of 0.002 in. The tensile bars were fractured in a hydrogen or helium atmosphere of 104 psi at ambient temperatures. The system used for mechanically testing the specimens is to be described in detail elsewhere.19 Several specimens of each type were tested in air using an Instron testing machine. The same yield strength and ultimate tensile strength were obtained in 104 psi helium with the above system as with the conventional testing machine. Magnetic analysis was employed to determine that there was a (bee) martensite in plastically deformed 304L and that it was not present in plastically deformed 310. The magnetic technique depended on allowing the material being studied to serve as the core between a primary and secondary coil. Thus, any change in the amount of magnetic material present between the annealed and plastically deformed steels will be indicated by corresponding changes in the induced voltage in the secondary circuit." The ratio of the output signal of a nonmagnetic stainless steel to a completely magnetic maraging steel was 2000 to I. Several unnotched 304L bars tested in hydrogen were analyzed for hydrogen by vacuum fusion analysis. There was an increase in the hydrogen content to approximately 2 ppm for the specimens tested in hydrogen, as compared to less than 1 ppm for the as-received material. Several thin sections cut from notched areas of 304L specimens tested in hydrogen and containing the fracture surface contained approximately 1.5 ppm H. The accuracy of these determinations was estimated to be ± 50 pct.

Jan 1, 1969

By G. L. Fisher, R. H. Geils

The effect of small amounts of columbium (<0.01 to 0.10 pct) on the ?-a transformation occurring during the continuous cooling of a low carbon Ni-Cu steel was investigated. Dilatometer specimens were aus-tenitized at 950" and 1068?C and cooled at 17? and 375 C° per min. Columbium caused a marked depression in the ?-a transformation temperature except when cooling at the slower rate from 950°C. The effec of columbium on the transformation temperature was greater the higher the austenitizing temperature and rate of cooling. A maximum depression of 92 C" was observed. Metallographic examination of specimens of <0.01 and 0.07pct Cb steels heated at 1200°C for 1 hr and cooled at various rates showed that columbium had a major effect on the ferrite morphology. The fer rite in the columbium -free steel remained equiaxed at cooling rates as high as 440 C? per min while the columbium-bearing steel exhibited mixed structures o equiaxed and bainitic ferrite at cooling rates as low as 130 C° per min. The ? grain boundaries in the columbium -free steel provided the ferrite nucleation sites in rapidly cooled specimens. There was a complete absence of nucleation at these sites in the colum bium-bearing steel. It is concluded that columbium depresses the transformation temperature by suppressing ferrite nucleation at the austenite grain bound-aries. In this respect the effects of columbium are analogous to those of boron in low C-Mo steels. It is well known that small columbium additions can substantially strengthen plain carbon steels. As little as 0.02 pct Cb can increase the yield strength of mild steels by 10,000 psi.1 A fine precipitate of CbC has been observed in columbium-bearing steels2 and is generally thought to be responsible for the strengthening. Little attention has been devoted to the effect of columbium on the ?-a transformation. Webster and woodhead3 have studied the effect of columbium on the isothermal proeutectoid ferrite reaction in mild steels. They found similar transformation behavior in steels both with and without columbium additions. However, as the austenitizing temperature increased, the incubation time for the start of the ferrite transformation became longer in the columbium-containing steel. Morrison1 found that the addition of 0.03 pct Cb to a C-Mn steel lowered the transformation temperature by 50 C° during cooling from 1200°C at a rate of 80 C" per min. The strengthening effect of columbium has recently been utilized in an age-hardenable, low-alloy steel containing copper and nickel.4 A small amount of columbium has a substantial effect on the as-rolled strength of this steel. By increasing the columbium level from <0.01 to 0.13 pct the as-rolled yield strength is increased by 15,000 psi. Columbium also significantly lowers the ?-to-a transformation temperature of this steel during continuous cooling from the austenitizing temperature. Because of the low carbon level in this steel (0.05 pct max), it is almost entirely ferritic. Thus, it offers the opportunity of studying the effect of small columbium additions on the proeutectoid ferrite reaction. Of particular interest in this study was the reason for the marked lowering of the transformation temperature by columbium during continuous cooling. EXPERIMENTAL PROCEDURE Materials. The compositions of the steels used in this investigation are shown in Table I. The steels were 30-lb air induction melts. They were forged to 4 by 8 by 1 in. plate at 1230°C, air cooled, and then reheated to 1230°C and cross-rolled in two passes to in. plates. Dilatometry. A Leitz Bollenrath dilatometer was used to record the transformation during continuous cooling from two different austenitizing temperatures. The dilatometer specimens were + in. in diam and 2 in. long. Oxidation and decarburization of the specimens was prevented by maintaining a small positive pressure of dry argon in the dilatometer furnace and by plating the specimens with 1 mil of Cu. For the lowest cooling rate, 17 C" per min, the temperature of the specimen was measured with a Pt-Pt 10 pct Rh thermocouple placed in a & in. diam well in the center of the specimen. During air cooling, 375 C° per min, this method of measuring the temperature interfered with the operation of the dilatometer. However, it was found that the temperature of the specimen could be measured accurately by placing a thermocouple in an identical specimen in a holder adjacent to the one being used to operate the dilatometer mechanism. The dilation-temperature curves were recorded on photographic film and then converted to volume percent ferrite-vs-temper-ature curves. The cooling rates obtained with the dilatometer are shown in Table 11. Cooling rates of

Jan 1, 1970

By J. M. W. Mackenzie, C. J. Wood

In attempting to describe the size classification performance of a hydrocyclone, most workers have elected to use either an equilibrium orbit theory or an non-equilibrium orbit theory. The equilibrium orbit theory has been used by the majority of workers including Lilge,&apos; Bradley; and Yoshioka and Hotta. In applying this theory, it is argued that particles in the body of a hydrocyclone attain an equilibrium radial position where the drag force on the particle resulting from the inward radial fluid velocity is balanced by the outward centrifugal force caused by the tangential component of fluid flow. When considered over the full height of the hydrocy-clone, attainment of this radial equilibrium orbit results in the particle following a conical equilibrium envelope. It is then argued that if this envelope lies outside the envelope of "zero vertical velocity," the particle will report to the underflow, while if the equilibrium envelope lies inside the envelope of "zero vertical velocity," the particle will report to the overflow or vortex finder product. The d50-sized particle which reports in equal quantities to the underflow and overflow is assumed to correspond to particles whose equilibrium envelope is coincident with the envelope of "zero vertical velocity." In considering the equilibrium orbit theory, it is apparent that the horizontal position of the particles in the feed inlet pipe should have no effect on their ultimate destination on the hydrocyclone. Each particle should attain an equilibrium position which depends on the density, size, and shape of the particle; the density and viscosity of the fluid; and the flow patterns within the hydrocy-clone. The nonequilibrium orbit or unsteady state theory has been largely developed by Rietema4 and Mizrahi.6 Mizrahi has listed four main objections to the equilibrium orbit theory. These objections center on the short residence time in the hydrocyclone, the fact that the experimental classification curve is much less sharp than is theoretically predicted, and the absence of negative efficiency conditions in hydro cyclones operating on a feed material which is much finer in size than d50. Proponents of the nonequilibrium orbit theory argue that for a particle to discharge with the underflow it must have sufficient outward radial velocity to reach the downward-flowing region close to the hydrocyclone wall in which the flow lines are parallel to the wall and the ratio of vertical to radial velocity is constant. It is then postulated that a d50 particle entering the cyclone at the center of the feed inlet will just reach this downward-flowing region as it reaches the apex. Thus for uniform distribution of particles across the feed inlet, half the d50 particles—that is, those injected in the half of the inlet area nearest the cyclone wall —will report to the underflow while those injected in the other half will not reach the downward-flowing region and will be carried inward to the center of the cyclone and thus report in the overflow. The exact thickness of the down-ward-flowing region of fluid adjacent to the outer wall of the hydrocyclone is uncertain but Mizrahi considers it to be equal to the apex radius minus the air core radius. Particles larger than d50 have a greater outward centrifugal force acting on them than the d50 particles and may reach the wall even if injected at a distance from the wall greater than Di/2 (Di is inlet diameter). Conversely, particles smaller than d50 may not reach the wall even if injected at a distance less than Di/2 from the cyclone wall. Since the equations put forward by the proponents of both theories yield approximately the same values of d50, it is not possible to decide between these theories by measurement of d50. It should be possible however to examine the theories by injecting a small stream of solids into the feed inlet of a hydrocyclone running on clear water. If the efficiency or classification curve is measured for various horizontal injection positions, then the curves should be coincident if the equilibrium orbit theory holds. If, however, the unsteady state theory describes the cyclone operation, then the classification curves should show finer d50 sizes for particles injected close to the cyclone wall. Experimental A 6-in.-diam hydrocyclone with geometry as in Figs. 1 and 2 was used. Quartz particles were injected as a 50% by wt pulp via an 1/8-in. steel probe. For each in-

Jan 1, 1971

By G. L. Chierici

Starting from Muskat&apos;s theory of water and gas coning, maximum permissible oil production rates without water and/or free-gas production have been determined, in a broad range of reservoir and well parameters, using the potentiometric model technique. The main assumptions made are as follows: (1) the reservoir rock is homogeneeous (either isotropic or anisotropic); (2) the volume of the aquifer underlying the oil zone is very small, so that it does not contribute to reservoir energy; and (3) the gas cap expands at a very low rate, so that it can be assumed to be in quasi-static conditions. The results obtained are presented in the form of diagrams which can be used for solving two types of problems: (1) given the reservoir and fluids characteristics, as well as the position and length of the perforated interval, determine the maximum oil production rate without water and/or free-gas production; and (2) given the reservoir and fluids characteristics only, determine the position and length of the perforated interval which optimize the maximum permissible oil production rate, without water and/or free-gas production. INTRODUCTION In oil reservoirs where the oil-bearing formation is underlain by an aquifer which does not participate in the production mechanism, water-coning is a limiting factor to the flow rates of producing wells. Production rates are usually kept to a value that will prevent the water from entering the wells. The entry of water into a well lowers its productivity by increasing the weigbt of the fluid column; moreover, the separation of water from the effluent, at the surface, may constitute a very difficult problem in cases of heavy viscous oils. A similar situation is encountered in oil reservoirs with a gas cap overlying the oil-saturated zone; here a downward gas cone is induced by the flow of oil towards the producing wells. Production rates must be low enough to prevent the gas from being produced; producing gas from the gas cap would be a waste of energy. Of course, water-coning and gas-coning phenomena can occur at the same time in the same reservoir if the oil-producing formation is both overlain by a gas zone and underlain by a water zone. Due to its relevant practical importance, the mechanism of coning was studied by many people.2,3,5-8 Defining the conditions for getting the maximum water-free and/or gas-free oil production rate is a difficult problem, often encountered under one of the following aspects: 1. Predict the maximum flow rate that can be assigned to a completed well without the simultaneous production of water and/or free-gas. 2. Define the optimum length and position of the interval to be perforated in a well, in order to obtain the maximum water and gas-free production rate. A systematic study of these problems was made by means of the electrical analog technique. The results of this study are presented here, under the form of a set of curves providing solutions for the above stated problems. These curves are valid only for homogeneous forrnations, either isotropic or anisotropic. Should the formation be non-homogeneous (by horizontal or vertical variation of permeability, shale diaphragms, fractures, etc.), a specific potentiometric study would be required for each specific case. Especially when shale diaphragms of some radial extension are present, the critical rates observed are much larger than would be expected from the diagrams. STATEMENT OF THE PROBLEM In the present study the aquifer is supposed to be of such limited volume that it does not contribute to the energy of the reservoir. Moreover, the gas cap is supposed to expand at such a low rate that the potential gradient in the gas cap is negligible. Under static conditions water-oil and gas-oil interfaces (T1 and T2) are both horizontal. When the reservoir production starts, below each well these interfaces take a cone-like shape (Fig. 1) having as an axis the axis of the well. This shape results from the equilibrium between potential gradients in the oil zone and gravitational forces due to density differences between oil and water and between oil and gas. Assuming the oil-bearing formation to be homogeneous and the oil to be incompressible, the analysis of the problem (see Appendix) shows that the oil-water and gas-oil interfaces are stable only if the oil production rate of the well is not higher than the following values.

Jan 1, 1965

JOSEPH DANIELS, Seattle; Wash. (communication to the Secretary*). Mine models are of great value to the student and to the layman in visualizing underground conditions, and, in a measure, should be just as much a part of the equipment of a mining school as sets of ore specimens, catalogs, or drawings. The chief drawback, as Professor Stock has indicated, is the time and cost of making them. The greatest good in the development of the model comes to the person who makes it, and I have often wondered whether it might not be possible to have each student make one model during his undergraduate career. At the University of Washington we have been collecting sets of mine timbers, made of 6 by 6-in. lumber, illustrating shaft, level, and stope timbering. This work has been done by freshmen. Perhaps each educational institution could specialize in the creation of a certain type of model and exchange its product for that of another school, just as we now do with ore collections. In this way we could build up good museums at a relatively low cost. JOHN R. CHAMBERLIN, New York, N. Y. (communication to the Secretary?).-The type of model described by Professor Stoek is admirably suited to exhibits of coal mining in horizontal veins, and fulfills perfectly the three purposes mentioned. As an educational illustration in colleges, especially when the students themselves build the model under the direction of their instructors, it is of the highest value; and as each condition in mining requires special methods to depict properly in a model, the student is compelled to exercise considerable inventive resource to construct a true representation, stimulating the imagination and interest in his subject. Models built for exhibits in lawsuits are usually constructed to show prominently some particular feature of vein formation or geology, or the relation of underground workings to surface property lines, and as such their use is invaluable to the successful litigant. When the litigation is ended, it is natural that the model should be relegated to the basement and frequently destroyed, as data on underground workings are often considered of a private character by the operators; and it is

Jan 10, 1917

By George Burgess

NOTE BY THE EDITOR.-This resume of a Technologic Paper which is published in full by the U. S. Bureau of Standards, is brought before the membership of the Institute with the object of affording an opportunity for the open discussion of results of an investigation by the authors named above, of some phases of the manufacture of steel rails which are of great importance to manufacturer and consumer alike. This resume will be presented at the Pittsburg Meeting of the Institute. Discussion is invited, by either members or non-members of the Institute. The discussion may be sent in writing to the Editor, in advance of the meeting, or should preferably be presented in person at the meeting. To those who desire to discuss, copy of the full Technologic Paper (No. 38), as published by the Bureau of Stanaards, will be sent upon request addressed either to the Bureau of Standards, Washington, D. C., or to the Editor, American Institute of Mining Engineers, 29 West 39th Street, New York, N. Y. Summary of Researches and Conclusions The main objects of this investigation were to determine, from measurements taken at representative rail mills, the present American practice regarding the temperatures at which rails are rolled; to demonstrate the ease and accuracy with which such temperatures may be measured, without interfering in any way with the manufacture of the product; to find out what the "shrinkage clause" in rail specifications really means; and, finally, to determine some of the physical properties of rail steels, particularly those of interest in manufacture, some of which seem to be insufficiently known as yet. 1. Ingot Temperatures.-Measurements made in four mills show that ingots for rails are rolled at temperatures ranging from 1,075° to 1,150° C. (1,965° to 2,100° F.), and that, in a series of 20 to 40 ingots, the variation in temperature from one ingot to another is only 10° to 20° C. 2. Finishing Temperatures.-Rails are finished at temperatures ranging broadly from 880° to-1,050° C. (1,615 to 1,922° F.), but usually ranging within 50° C. of 935° C., and occasionally above 1,100° C.

Jan 9, 1914

"In the spring of 1927, six members of the American Institute of Mining and Metallurgical Engineers met for dinner at the Chemists&apos; Club in New York to discuss the possibility of setting up a committee within the Institute to further the current interest in the science of steelmaking. Attention to this subject had been crystallized by a symposium held by the Faraday Society in 1925. After a prolonged discussion, ranging from thermodynamics to slag conditioning, it was decided to approach the Institute with the request that a standing committee on "The Physical Chemistry of Steel Making" be set up. This committee proposed to promote scientific and practical papers on the subject, and was designed to cooperate with the Open Hearth Committee of the Institute in bringing scientific developments to the attention of open-hearth operators throughout the country. . . . "As the life of the [Physical Chemistry of Steelmaking] Committee lengthened and general interest in the technical phases of steelmaking grew, it .became evident that there was a distinct need for a book that might serve the open-hearth interests to better advantage than standard texts whose scope is necessarily wide and whose detailed exposition of the open-hearth process is, therefore, somewhat limited. With this thought in mind, the Committee, after some years of consideration and debate, embarked on the venture of writing a manuscript on &apos;Basic Open Hearth Steelmaking&apos;." The foregoing paragraphs, taken from the introduction by C. H. Herty, Jr. to the first edition, well describe the circum- stances which led to the publication of “Basic Open Hearth Steelmaking” in the spring of 1944. The book consisted of nine- teen chapters contributed by twenty-three authors and edited by the staff of Alloys of Iron Research and T. S. Washburn, H; M. Larsen, and J. S. Marsh with Frank T. Sisco as consulting editor. The Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME, made financial grants; steel companies and other organizations supported the publication by contributing time and expenses of staff members in their capacity as authors or editors. The volume was sponsored by the Seeley W. Mudd Memorial Fund and appeared under the

Jan 1, 1964

Homestake&apos;s Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered&apos; the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By V. H. Wilhelm

The outstanding event in the California petroleum industry during 1931 was the continuance of curtailment of crude oil production, which directly reduced drilling and well repair activities. Although all objectives were not attained, a very close balance between supply and demand was maintained during the period of maximum requirements, but the decline in intercoastal and export shipments caused an overproduction during the last half of the year, which indicated that California production would necessarily suffer further curtailment after the end of the year. A new peak in potential crude oil production of 1,187,600 bbl. per day was reported in August and at the close of the year the California potential was 1,069,000 bbl. per day, the shut-in light oil amounting to practically 425,000 bbl. per day and the shut-in heavy oil amounting to about 150,000 bbl. per day. Fig. 1 depicts these conditions and also shows the production and curtailment situation since the inception of proration in California. The December, 1931, potential figure of 1,069,-000 bbl. per day was arrived at after the most careful deliberation by a number of committees, selected to check the potential of practically every well in the state. Continued overproduction in the first three months of 1931 and the inadvisability of building more storage, together with the inability to obtain the proper amount of curtailment in town-lot fields, such as Long Beach, Santa Fe Springs and Playa del Rey, prompted the major oil companies to inaugurate a price reduction in crude oil. This cut caused prices to reach the lowest levels since 1915, and instigated the formation of an oil sales agency, composed of independent operators, which is known as the Oil Producers Sales Agency. The purpose of this organization is to procure a market for its members at reasonable prices, advise them of market conditions and aid them in controlling the amount of oil available for sale. Marketing of oil produced by members began on June 1 and independents controlling" about 160,000 bbl. per day of production had become members by the end of the month.

Jan 1, 1932

By T. G. Chapman

THE writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. EARLY EXPERIMENTAL WORK In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of&apos; these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By Arthur Connolly

WHEN scientific literature was lacking or meager, research necessarily meant laboratory investigation above all else. Today, scientific literature has attained tremendous proportions, and the volume increases at a much faster rate than it is digested and efficiently utilized. For that reason the present-day research worker should spend much more time in the library, and correspondingly less in the laboratory, than is the general custom. Library research would overcome two serious errors often made by scientists: duplication of work described completely and failure to appreciate inventions described almost verbatim in the literature. To emphasize these failings that often occur in present-day research, consider a hypothetical scientist as he conducts his search from inception to the stage where it is made available to the public by patent or other publication.

Jan 1, 1942

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker&apos; measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-&apos; sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"&apos; which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963

By Rollyn P. Jacobson

THE town of Pacific, in Jefferson County, Mo., is 127 miles west of St. Louis. Since the area lies entirely on the flood plain of a cutoff meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus" were used. In all but a few cases, the electrode spacing, A, was increased in increments of 11/2 ft to a spread of 30 ft and in increments of 3 ft thereafter. Initial drilling was done with a rig designated as the California Earth Boring Machine, which uses a bucket-shaped bit and produces a hole 3 ft in diam. Because of excessive water conditions and lack of consolidation in the gravel there was considerable loss of hole with this type of equipment. A standard churn drill was employed, therefore, to penetrate to bedrock. Eighteen bucket-drill holes and eight churn-drill holes were drilled at widely scattered locations on the grill. The depth to bedrock and the configuration will not be discussed, as this parameter is not the primary concern. Thickness of overburden overlying the gravel beds or lenses became the important economic criterion of the prospect.** The wide variety and gradational character of the geologic conditions prevailing in this area are illustrated by sample sections on Fig. 2. Depth profiles at stations E-3 and J-7 are very similar in shape and numerical range, but as shown by drilling, they are measures of very different geologic sequences. At 5-7 the gravel is overlain by 15 ft of overburden, but at E-3 bedrock is overlain by about 5 ft of soil and mantle. Stations L-8 and H-18 are representative of areas where gravel lies within 10 ft of surface. In most profiles of this type it was very difficult to locate the resistivity breaks denoting the overburden-gravel interface. In a number of cases, as shown by stations M-4 and H-18, the anomaly produced by the water table or the moisture line often obscured the anomaly due to gravel or was mistaken for it. In any case, the precise determination of depth to gravel was prevented by the gradual transition from sand to sandy gravel to gravel. In spite of these difficulties, errors involved in the interpretation were not greatly out of order. However, results indicated that the prospect was very nearly marginal from an economic point of view, and to justify expenditures for plant facilities a more precise evaluation was undertaken. The most favorable sections of the property were tested with hand augers. The original grid was followed. In all, 46 hand auger holes were drilled to gravel or refusal and the results made available to the writer for further analysis and interpretation. When data for this survey was studied, it immediately became apparent that a very definite correlation existed between the numerical value of the apparent resistivity at some constant depth and the thickness of the overburden. Such a correlation is seldom regarded in interpretation in more than a very qualitative way, except in the various theoretical methods developed by Hummel, Tagg (Ref. 1, pp. 136-139), Roman (Ref. 2, pp. 6-12), Rosenzweig (Ref. 3, pp. 408-417), and Wilcox (Ref. 4, pp. 36-46). Various statistical procedures were used to place this relationship on a quantitative basis. The large amount of drilling information available made such an approach feasible. The thickness of overburden was plotted against the apparent resistivity at a constant depth less than the depth of bedrock for the 65 stations where drilling information was available. A curve of best fit was drawn through these points and the equation of the curve determined. For this relationship the curve was found to be of the form p = b D where p is the apparent resistivity, D the thickness of overburden, and b a constant. The equation is of the power type and plots as a straight line on log-log paper. The statistical validity of this equation was analyzed by computation of a parameter called Pearson&apos;s correlation coefficient for several different depths of measurements, see Ref. 5, pp. 196-241. In all but those measurements taken at relatively shallow depths, the correlation as given by this general equation was found to have a high order of validity on the basis of statistical theory.

Jan 1, 1956