Search Documents

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

[ ]

Jan 1, 1907

By Susanne Pignolet, Richard D. Hagni

Ore microscopy has been applied to the complex cobalt-nickel- copper-lead-zinc ores from the Madison Mine in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposit, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate and nickel contamination of the copper matte at the smelter. In ores from high stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the the recovery of cobalt and nickel in the siegenite concentrate. However some cobalt and nickel will be lost to the tails as bravoite-pyrite particles due to the intimate intergrowth of these minerals. Other textures which may result in beneficiation problems include the intimate intergrowth of chalcopyrite and galena and the occurrence of sphalerite as inclusions in galena.

Jan 1, 1984

El Indio, eighty percent -owned by Compania Minera an Jose Inc., a subsidiary of St. Joe Minerals, and twenty percent-owned by private Chilean investors, will open their new flotation and Carbon -In -Pulp plant near La Serena, 480 km (300 miles) north of Santiago, Chile, in early 1981. The underground mine, at an altitude of 4,270 m (14,000 ft), will produce about 1,270 mt per day (1,400 st per day) of ore containing about 2. 2570 Cu, and gold and silver to the extent of 16 and 254 g per mt (0.47 and 7.4 oz per st) respectively. While construction of the plant was underway, development ore, containing some 1,400 kg (45,000 oz) of gold, was shipped to the United States for recovery in a copper smelter. At El Indio the underground ore is rail-hauled to the mill a short distance from the portal where it is crushed, ground, and floated to produce a copper concentrate containing both gold and silver. The crushing plant also crushes waste for use as mine backfill. Approximately 92% of the copper and 60% of the gold and silver are recovered in the flotation concentrate. Flotation tailings, at a grade of 19 g Au and 116 g Ag per mt (3.4 oz Au and 0.55 oz Ag per st), are cyanided for 72 hours in six Pachucas with auxiliary air lifts for pulp transfer. Lime, cyanide, lead nitrate, and a phosphate are also fed to the cyanidation Pachucas. After cyanidation, the pulp is treated in four air lift Carbon-In-Pulp tanks equipped with external vibrating screens for carbon advance. Loaded carbon is stripped in two pressure vessels in parallel. Pressure stripping must be used because of the high altitude. Stripped carbon is dewatered in a spiral classifier before being reactivated in a rotary kiln and returned to the C. I. P. circuit. Pregnant solution is then sent to four banks of four Zadra cells for gold and silver recovery on steel wool. Zadra cell cathodes.are washed with the slimes being captured in a plate and frame filter. The filter cake and the washed cathodes are then dried on an infrared dryer and smelted in two stages to bullion bars. Published reports indicate that the total investment for this unique operation was in the neighborhood of $80 million.

Jan 1, 1981

By Frank C. Canney

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

By James Terry Duee

No important producing developments took place in Colombia during the year 1928. This was at least partly due to the paralysis of operations by the passage, during the latter part of 1927, of a law which was regarded by the oil companies as confiscatory and unjust, and the promulgation of exceedingly stringent regulations of this law under decree No. 150, published Jan. 28, 1928. This decree, which contained 24 articles, practically prevented not only producing operations by the oil companies but even such activities as geological explorations and surveying, as severe fines were imposed for the possession of maps not registered with the Ministry of Industries. Both this regulatory decree and the law were subject to attack in the courts by several of the oil companies. The regulatory decree was suspended May 22 by Presidential proclamation, until the suits against it are decided by the Supreme Court and Council of State. Though another law was introduced into the Colombian Congress at a later date, no action was taken on it, and at the time of the writing of this paper, it would appear that no oil bill will pass the Colombian Congress during the present session. The Barco concession, which was revoked in February, 1926, still continues an unsettled matter, although there have been rumors that the government was attempting to come to some decision on this rather difficult question. A hopeful sign toward the close of the year was the settlement of negotiations with the Tropical Oil Co. over the acceptance of the payment for royalties due the government from that company. This settlement, which covered a royalty on crude oil produced from June 30, 1926 to June 30, 1928, represented a cash payment for approximately 3,000,000 barrels. It is to be hoped that during the coming year the Colombian government will see its way clear to clarify its position on petroleum legislation. A good augury for the future was the statement made by President Abadia Mendez on New Year's Day, in which he courageously admitted the errors of previous legislation and said, regarding oil, "Very soon

Jan 1, 1929

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By C. B. Alcock, L. I. Cheng

By the use of radiochemical methods for the study of the gas-liquid equilibria at low temperature, and for the determination of the sulfur contents of metal beads which had been equilibrated with H2S/H2 mixtures of known sulfur potential, it has been possible to obtain the liquid solubility and the free energy of solution of sulfur in liquid tin and lead at temperatures between 500°and 680°C. THE gas-liquid equilibrium method has proved in the past to be most successful in the determination of the thermodynamic behavior of dilute solutions of sulfur in liquid metals.1,2 One of the basic requirements for success with this method is that the volatility of both the metal and its lowest sulfide should be small, otherwise sulfide will be deposited at the cool end of the furnace, where it may react with the outgoing gases to form either sulfur-rich lowest sulfide or higher sulfides. The resultant value of the apparent equilibrium constant will then be lower than the correct one. This argument applies even at sulfur potentials below that in equilibrium with a separate condensed phase of the lowest sulfide at the reaction temperature, T. The mass of sulfide which is deposited at the cold end of the furnace, and hence the extent to which further reaction occurs with the outgoing gases, depends on the time taken for equilibrium to be reached between metal and gas. Since this will depend principally on the bulk of the metal phase which is used, one should clearly attempt to uie as small metal samples as possible. These considerations are important in the study of dilute solutions of sulfur dissolved in liquid tin and lead which both have moderately high vapor pressures as metals and form volatile sulfides. The limit on the size of the metal samples which may be used is set chiefly by the difficulties of analysis for very small amounts of sulfur. The oxygen or carbon dioxide combustion method, followed by iodimetric determination of the sulfur dioxide which is formed,has been found to be successful for the determination of small amounts of sulfur in copper, iron, cobalt and nickel.4 This method was unsatisfactory for sulfur dissolved in tin and lead, mainly because the sulfur dioxide was to some extent absorbed by the copious tin or lead oxide deposits which were formed on the walls of the combustion tube. Furthermore some of the sulfur was found to segregate on the surface of the beads as flaky sulfide crystals which would easily be lost in the transfer of a bead from a boat in the gas equilibration apparatus to one in the combustion apparatus. Oxidation in aqueous media to sulfate ion followed by precipitation as barium sulfate was, therefore, adopted as the analytical procedure. The gas-metal equilibrium experiments were all carried out with radioactive sulfur and thus the analysis involved the counting of barium radiosulfate. Furthermore the use of the radioisotope meant that the approach to the gas-metal equilibrium could be followed continuously by gas counting.' The metal beads were held separately in glass crucibles during equilibration and were transferred from the furnace to the beaker for dissolution in nitric acid still in the crucibles, and thus the possibility of sulfur loss by detachment of the sulfide segregates was eliminated. The temperature range of this investigation was 500° to 680°C. EXPERIMENTAL APPARATUS AND METHOD The apparatus consisted of two furnaces placed in series in a gas recirculation system, Fig. 1. One furnace F1, which was vertical was used to heat the alumina crucible, A, holding six metal beads in separate glass crucibles. The beads weighed between 300 and 700 mg each. The crucible assembly was introduced and removed from the furnace mechanically under a stream of oxygen-free argon. The other furnace, F2, was horizontal and was used to heat a cobalt Co9S8 mixture, held in an alumina boat, and made with radiosulfur containing about 1/2 millicurie per g of sulphur. This mixture, which was finely powdered, was used as a source of known H2S/H2 mixtures6 for a given furnace temperature. The recirculation system also contained a gas re-circulation pump (P), an end window Geiger-Miiller counter (N)—placed downstream of F1 so as to monitor the H2S pressure in the gas leaving this furnace— a sample volume for chemical analysis of the gas phase (G), gas drying tubes (D), filling taps and other standard ancillary equipment. The gas sampling volume was principally used in the cali-

Jan 1, 1962

By M. J. Marcinkowski, D. B. Crittenden, A. S. Sastri

A study co.mbining stress-strain .measurements in conjunction with transmission electron microscoPy has been made with near equiatomic Fe-Cr alloys which were aged for various times at 500°C. Associated with this aging is a marked increase in deformation twinning. The outstanding feature of these twins is that they generate stress fields sufficiently great so as to give rise to spontaneous dislocation loop nucleation nearly normal to the propagating twin. This observation is in agreement with the theoretically predicted elongation of the stress field of a dislocation Perpendicular to its direction of motion as it moves near the speed of sound. Dislocation loop nucleation is more difficult in the longer aged alloys so that this energy absorption mechanism is not effective in hindering twin propagation. Since crack nucleation can readily occur near the tip of a twin, the aged alloys become extremely brittle when deformed in tension. Iron-chromium alloys in the vicinity of the equiatomic compositions become severely embrittled when aged at about 500°C. Fisher et 01.' have shown that this embrittlement is related to the decomposition of the original random Fe-Cr solid solution into a chromium-rich and an iron-rich phase. In addition, Mar-cinkowski et a1.' have shown that twinning becomes an increasingly more important mode of deformation as the aging time is increased. These results have been recently corroborated by the transmission electron microscopy study of Mima and amauchi . The Fe-Cr alloy thus seems ideal for verifying the predictions made in Parts I4 and 115 of this investigation where the behavior of large static or blocked twins and those of large dynamic or propagating twins, respectively, were investigated numerically. It was thus decided to measure the stress-strain curves generated by embrittled alloys that were aged for various times and to examine sections by transmission electron microscopy. EXPERIMENTAL PROCEDURE Electrolytic iron and electrolytic chromium were vacuum-melted and poured into ingot form. The composition of the resulting alloy was found to contain 46.0 wt pct Cr (47.8 at. pct), the remainder being iron. The resulting ingot was swaged above 850°C into 0.250-and 0.400-in.-diam rounds. Compression samples of 0.250 in. diam and 0.400 in. long were cut from the smaller-diameter rounds. These samples were then sealed in evacuated quartz tubes and annealed for 30 min at 1150°C to produce a uniform and equiaxed grain size of mean diameter equal to 1.73 mm. They in turn were rapidly quenched from 850°C so as to preserve the condition of random solid-solution characteristic of the elevated temperature. The samples were then aged for various times up to 300 hr at 500°C in a massive Pb-Bi alloy bath. The samples were next polished and tested in compression at room temperature as described in Ref. 6 using an Instron tensile testing machine. The strain rate used was 0.05 in. per in. per min. The remaining larger round was converted into compression specimens of 0.325 in. diam and 0.500 in. long. This larger diameter enabled wafers of sufficient size to be prepared for examination by trans-mission electron microscopy techniques after subjecting them to a suitable strain. Foil preparation is described in some detail in Ref. 6. All foils were examined in a type HU-11A Hitachi electron microscope operating at 100 kv. RESULTS AND DISCUSSION Fig. 1 shows the effect of aging at 500°C on the room-temperature stress-strain curves of the FeCr alloys. For greater clarity the origin of each curve has been displaced upward. The same origin has been used for both the 0 and the 0.1 curves. It is apparent that with increased aging times a sharp drop in load is observed at the yield stress which becomes more pronounced as aging proceeds. A loud sonic burst accompanies this drop and subsequent metallographic examination shows the sample to contain numerous twins. For intermediate aging times, a number of smaller twin bursts follow the initial large one. The total plastic strain associated with the twinning mode of deformation can be obtained by adding up the contributions AE~ from all i twin bursts, i.e., £,¦££,-, in the manner illustrated schematically in Fig. 2. The contraction of the specimen, as measured from the strip chart of the Instron, after suitably correcting for the elasticity of the machine, was converted into true strain using the assumption that there was no volume change and that the sample remained cylindrical. The dashed lines are all drawn parallel to the

Jan 1, 1970

By A. E. Bibb, J. R. Fascia

Single-crystal wafers of zirconium have been exposed to 680°F neutral water. The single crystals were of known orientation and weight-gain data as a function of crystal orientation were obtained. These data show that all the crystal faces studied obeyed a cubic rate law out to the time of transition whereupon the crystals corroded at an approximately linear rate. The time to transition varied from 114 days for (1074) crystals to about 325 days for the (2130) faces. The epitaxial relationship be-tween metal and monoclinic oxide was found to be (0001) H (111) and [1120] 11 [101]. A black tight adherent oxide layer was formed on the crystals in the pretransition range. This black oxide was found to be monocrystalline. The white corrosion product produced after transition was found to be polycrys-talline but highly oriented. X-ray line-broadening studies found that the black oxide was a highly strained structure whereas the white oxide was relatively strain-free. These results indicate a strain-induced re crystallization or fragmentation accompanies the change from protective black oxide to nonprotective white oxide. ZIRCONIUM alloys have been used quite extensively in high-temperature aqueous environments. Alloy additions can be made to commercial sponge zirconium which enhance the corrosion resistance of the zirconium in both water and steam media, which raise the tolerance limit for certain impurities detrimental to corrosion resistance, and which reduce the amount of free hydrogen pickup during corrosion. The development of the corrosion-resistant zirconium alloys has been a long and tedious job involving trial and error methods. This technique has been necessary because of a lack of fundamental data and hence understanding of the corrosion mechanisms. The objective of the work described herein was to provide some fundamental data with respect to the aqueous corrosion of zirconium crystals as a function of the orientation of the exposed surfaces. Hg. The zirconium chunk was then cooled to below the transformation temperature (862°C) and reheated to 1200°C for 8 hr. The ultimate size of the zirconium grains increased with the number of cycles. Rapid or even furnace cooling through the transformation temperature produces a considerable amount of substructure which was intolerable in corrosion experiments as it would be in the study of any crystallographically dependent property. It was found that a high-temperature a-phase anneal for approximately 4 days reduced the substructure below the limits detectable by visual or X-ray means. Crystals so produced were carefully cut from the massive zirconium chunk and oriented by standard back-reflection Laue techniques. The crystals were then mounted in a goniometer head and, by using the three degrees of freedom available, slices on the order of 0.015 to 0.020 in. were cut parallel to any desired crystal plane. These slices were then carefully polished on both sides to produce smooth flat faces, pickled to remove about 0.002 in. per face, annealed for 1/2 hr at '750°C in a vacuum of approximately 10"5 mm Hg, flash pickled, and checked for orientation. The pickling solution was 45-45-10 vol pct HN0,-H20-HF and continuous agitation was provided to eliminate pitting of the slices. Any slice that was not within 2 deg of the desired orientation was discarded, and any evidence of substructure as indicated by the Laue spots was also grounds for discarding the sample. Thin slices were used for the corrosion tests because weight gain per area data could be obtained with only a minimum area exposed to the corrosive media that was not of the desired orientation. The thin single-crystal slices were of irregular shape and as a result the areas were determined by placing a crystal inside an inscribed square of known area, enlarging a picture of this assembly about X5, and tracing both the enlarged square and crystal with a planimeter. The zirconium used to produce these single crystals was crystal-bar grade, a typical analysis of which is given in Table I. An oxygen analysis on prepared crystals gave a concentration of 205 ppm. The hydrogen concentrations are believed to be less than 15 ppm due to the dynamic vacuum anneal given each crystal. Typical nitrogen values for zirconium treated in this manner are about 10 to 20 ppm. RESULTS AND DISCUSSION Single-crystal wafers have been exposed to de-oxygenated, deionized water in static autoclaves.

Jan 1, 1964

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st'ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.'-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5'6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964

At the Kidd Creek mine operated by Ecstall Mining, Ltd. near Timmins, Ontario, Honeywell has installed a sophisticated new quick- thinking computer system that keeps tabs on conditions along three separate processing streams at once and relays continuous 60-second data to the mill operator. Believed to be the first of its kind, the system picks up data from two independent x-ray spectrometers simultaneously. A digital computer from Honeywell's Computer Control Division receives and interprets real-time information gathered by online x-ray analyzers, and the system then advises control room operators of the relative amount of each of five elements at five points in each of the three process streams. The system is reported to provide a quantitative analysis of the five elements at a given point in the process within one minute-which is about 120 times as fast as a chemical laboratory assay could be performed. With this instant data at his command, the mill operator can make timely process adjustments to correct any deviation from optimum flotation results, thus salvaging valuable minerals that would inevitably be lost with slower detection methods. The minerals recovered at Kidd creek are copper, lead, iron, silver and zinc.

Jan 8, 1968

By F. D. Rosi

The plastic properties of extended silver and copper crystals of varying purity were studied as a function of crystal orientation in the early stages of flow. Variations in the gross shape of the shear stress-shear diagram and in the properties of critical Variationsshear stress and shear-hardening coefficient were correlated with changes in slip-band developments. The phenomenon of work hardening is discussed in terms of the existing dislocation theory. IT appears certain from the early studies on the deformation characteristics in metal crystals1-3 that plastic flow takes place in a preferred crystallo-graphic slip system which is determined by the geometry of the crystal (law of maximum shear stress), and that the value of shear stress for this system is independent of crystal orientation (law of critical shear stress). Experimentally, it has been demonstrated further that the law of critical shear stress can be extended to include extensive plastic flow.&apos; Thus, the shear-hardening coefficient, which is defined as the slope of the shear stress-shear curve, also is considered to be independent of orientation. It is noteworthy that deviations from this empirical shear-hardening law have been reported in cubic crystals whose initial orientation favors slip on more than two systems.&apos; Moreover, this law appears to have been derived from stress-strain data relating to relatively high values of shear strain (0.5 to 4), where widespread slip and complex distortions can be expected, regardless of crystal orientation. Since existing data indicate that the strain inhomogeneity in a crystal is manifested particularly in the early stages of flow, it would appear that a more exacting test as to the fundamental nature of the shear-hardening law would be to investigate systematically the shape of the stress-strain curve as a function of crystal orientation in the earlier stages of deformation. With regard to the general form of the shear stress-shear curve for cubic crystals, early studies show a parabolic hardening law, where the shear 1 stress is proportional to the square root of the shear-strain. Since this law was predicted theoretically by Taylor" in his original dislocation model for hard- ening, it has been accepted widely as a fundamental flow characteristic of cubic metals. However, it was recently pointed out by Masing6 hat the parabolic law is not the elementary form of hardening in cubic crystals, but instead is a consequence of complexities in the flow process (e. g., deformation bands and unpredicted secondary slip). Thus, in the very early stages of deformation (< 2 pct extension) where the occurrence of such complexities is unlikely, a different strain-hardening behavior might be anticipated. This view is supported by the recent work of Rosi and Mathewson7 on high purity aluminum where a linear law was obtained for extensions up to 2 pct. A linear hardening over a wider range of deformation also was reported by Rohm and Kochendorfer8 ho deformed aluminum crystals under conditions approximating pure shear. Even more pertinent is the recent evidence of Masing and Raffelsieper9 on high purity aluminum crystals. It was found that for crystals having initial orientations near a <l00> or <1ll> axis, a high hardening was obtained, whereas crystals with a <110> orientation exhibited a low and linear hardening curve followed by a region of more rapid hardening. Since much still remains obscure concerning the details of strain hardening as well as slip-band formation in face-centered-cubic crystals in the early stages of deformation, the present study was undertaken to evaluate the effect of crystal orientation on these two important manifestations of glide. It is important to note here that at the time of this study, Lucke and Lange11 presented information on the orientation-dependence of the shape of the strain-hardening curve in aluminum of various purities. Their work, which essentially represents an extension of that of Masing and Raffelsieper, in many respects is parallel to that of the present study. Experimental Procedure Production of Single Crystals: Single crystals of silver and copper of varying purity were used in

Jan 1, 1955

JOHN.B. HASTINGS, Los Angeles, Cal. (written discussion).-This paper reminds me that when I had an option on a Nevada mine, where the only orebodies assayed $4 gold, I went to San Francisco to learn the cost of putting broken ore in a 25-ft, vein on the mine cars, and sought Mr. Alfred Wartenweiler, who said "There is not a mine in California that can tell what it costs to move ore in the stopes." When building small mills in the mountains, and with only 30 or 40 employees, by entering in a log at night the work performed by each man, I have been able to plot the costs with the accuracy shown in this paper, and very good discipline it is. Cost of new construction and repairs is carefully kept by most companies, and is compiled after completion; probably the outlay of labor and material in pieces of work sufficiently important to call for blueprints is estimated beforehand, but numberless odd jobs of construction and repairs are so itemized. . Might it not be worth while, at a large plant, to have these smaller daily tasks described in advance in a central repair office, and then let inspectors look over the job, report time and material needed, and enter it in sufficient detail in proper ledgers, the men then being sent to accomplish it, and reporting when finished? The forecasts would soon be made quickly and correctly and would give the head mechanic, carpenter, and electrician easy supervision of their men, and the results could be seen at a glance by the managers.

Jan 4, 1918

By J. J. Forbes

&apos;"THE Federal Coal Mine Safety Act (public Law T. 552. 82nd Congress) was approved oil July 16, 1952. It incorporates, as Title I, the Coal Mine Inspectio1.1 and Investigation Act of May 7. 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter. coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title 11 contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires. inundations. and man-trip 01. man-hoist accidents. At this point a brief account of events that preceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Govermment as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coalmine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small folce of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations aftel mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia. Ill., disaster of March 25. 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act. The act is a compromise measure. Senator Matthew M. Neely of West Virginia and Congressman Melvin Priec of Illinois introduced almost identical versions in the 82nd Congress, but they were considered too drastic. The final version was introduced by Congressman Samuel K. McConnel, Jr., of Pennsylvania, after considerable discussion and amendment in committee hearings. It was passed by the Congress and became effective when signed by the President on July 16, 1952. The act is somewhat limited in scope because it applies only to approximately 2000 coal mines in the United States and Alaska that employ regularly 15 or more individuals underground. It exempts approximately 5300 mines employing regularly fewer than 15 individuals underground and all strip mines, of which there are about 800. Moreover, it covers only conditions and practices that may lead to major disasters from explosion, fire, inundation, or man-trip or man-hoist accidents. According to Bureau records, such accidents have resulted in less than 10 pct of all the fatalities in coal mines. It is important to mention that the law is not designed to prevent the day-to-day type of accidents that have caused the remaining 90 pct or more of the fatalities, because it was the specific intention of the Congress to reserve the hazards which caused them to the jurisdiction of the coal-producing states. Many who opposed any Federal legislation that would give the Federal inspectors authority to require compliance with mine safety regulations claimed that such legislation would usurp or infringe upon States&apos; rights. To assure that the principle of States&apos; rights would be preserved, the act provides for joint Federal-State inspections when a state desires to cooperate in such activities. The Director of the Bureau of Mines is required by the act to cooperate with the official mine-inspection or safety agencies of the coal-producing states. The act provides further that any state desiring to cooperate in making joint inspections may submit a State plan for carrying out the purposes of this part of the act. Certain requirements are listed: these must be met by a state before the plan can be accepted. The Director of the Bureau of Mines, however, is required to approve any State plan which complies with the specified provisions. The Director may withdraw his approval and declare such a plan inoperative if he finds that the State agency is not complying with the spirit and intent of any provision of the State plan. When this paper was prepared, agreements for joint Federal-State inspections had been entered into with Wyoming and Washington. A few other states have indicated their desire to submit a State plan and negotiations toward that end are now under way. Reluctance to enter into such agreements may be due to the mine operators&apos; knowledge that in the states that adopt a cooperative plan they are prohibited from applying to the Director of the Bureau of Mines for annulment or revision of an order issued by a Federal inspector and must appeal directly to the Federal Coal Mine Safety Board of Review for such action. Experience has proved that review by the Director as provided in the act is a less expensive and time-consuming procedure to all concerned than applying to the Board. Reluctance also may stem from the fact that joint Federal-State inspections somewhat restrict the movements of the State mine inspectors and tend to reduce the number of inspections of mines. Where a State plan is not adopted, the Federal coal mine inspector is responsible under the law to take one of two courses of action if he finds certain hazardous conditions during his inspections. The first action involves imminent danger. If a Federal inspector finds danger that a mine explosion, mine fire, mine inundation, or man-trip or man-hoist accident will occur in a mine immediately or before the imminence of such danger can be elim-

Jan 1, 1955

By M. R. Tek, K. H. Coats, D. L. Katz

The nature and the limits of validity of Darcy&apos;s law US applied to the flow of natural gas through reservoirs has been considered in order to resolve some controversial aspects of the effect of turbulence on pressure drops. The equivalence between various concepts and viewpoints advanced in the past by several investigators to explain how and why a gas well does not necessarily perform according to Darcy&apos;s law is shown. Starting with generalized equations of flow of fluids through porous media, a partial differential equation has been derived which accurately represents the flow at all rates. This equation has been numerically solved using an IBM 704 digital computer. The results permit plots of unsteady radial pressure distribution curves from which specific isochronal backpressure curves may be constructed. These back-pressure curves show the effect of the ,8 factor on the slope of the back-pressure curve. The calculations further indicate that the drainage radius for a gas well in turbulent flow propagates at a rate dependent upon the rate of production at the wellbore. This is quite different from the case with liquid flow or natural-gas flow in laminar regime. Additionally, the effect of reservoir inhomogeneities and crossflow between layers of different permeability on the back-pressure performance of gas wells has been conridered. In light of the current numerical results the significance and linlitation of the rate of flow function Y proposed by Smith" has been discussed. INTRODUCTION The relationship between the pressure drop and flow rate in problems of fluid flow through porous media is known to be affected by the nature of flow through the porous matrix. It has been observed by many that, for a range of flow rates, the pressure drop remains proportional to the rate of flow. When some flow rate is reached, however, it is usually observed that the pressure drop gradually begins to increase more than proportionally to the flow rate. It is well known that this phenomenon was first observed by Osborne Reynolds in 1901 in experimenting with flow through pipes. In his classical experiments, Reynolds made visual observations on the condition of streamlines evidenced by injecting a dye into water flowing through glass tubes. In these experiments, the abrupt transition between steady, "streamline, laminar" flow and unsteady random turbulent flow was found to be a function of the dimensionless group (Dvp/u), now known as the Reynolds number. During these experiments, in addition to observations on the nature of flow regimes, the proportionality between flow rate and pressure drop in laminar flow was contrasted with the nonlinearity between these variables in turbulent flow. Fancher and Lewis&apos; reported data on various consolidated and unconsolidated sands in 1933. Their conclusions were that ". . . the flow of fluids through these porous materials closely resembles that through pipes; that there is a condition of flow in porous systems which resembles viscous flow, another which corresponds to turbulent; that the change from one type to the other takes place at a definite and reproducible condition for each system". In 1947, Brownell and Katz published a method to predict the laminar and turbulent flow behavior from the particle size, bed porosity and the particle sphericity, employing the friction factor-Reynolds number charts for pipes. Several investigators have verified the work of Fancher, Lewis and Barnes and presented their data as friction factor-vs-Reynolds number plots.&apos; The equation which would represent the pressure gradient over the whole range of velocity must have an added term over that represented by Darcy&apos;s law. Accordingly, the pressure gradient necessary to sustain flow at the velocity (v) through a porous medium may be represented by the following equation, suggested by Forscheimer." The nature and the range of validity of Darcy&apos;s law has been the subject of studies by many investigators over the past years. While everyone seemed to agree on the need for a quadratic correction term to Darcy&apos;s law to make it effective over the range of velocities, the concept of inception of turbulence and the use of the term "turbulent flow" remained controversial. Some fluid dynamicists define turbulence as a flow

By R. A. Breitrick, J. N. Swinderman, J. J. Cooper, H. L. Bauer Jr.

The Robinson Mining District, near Ely, Nev., is one of the major porphyry copper districts in the world. Within the district is an eight mile long east-trending zone of altered porphyry, metamorphosed sedimentary rocks, and sulphide mineralization surrounded by Paleozoic limestone, dolomite, shale and sandstone, Tertiary volcanics, and Quaternary alluvium. Six major disseminated ore deposits have been exploited in this zone. About 20% of the district production has come from disseminated ore in metamorphosed sedimentary rocks found adjacent to altered quartz-monzonite porphyry. The following brief statements summarize some of the relations between porphyry alteration, metamor-phism, and mineralization: 1) Disseminated copper ore does not occur in unaltered porphyry or in m-metamorphosed sedimentary rocks. 2) Sedimentary rocks have been only weakly metamorphosed where intruded by unaltered porphyry. 3) Intensely metamorphosed sedimentary rocks are found only adjacent to altered porphyry. 4) Many hydrothermal minerals are common to both altered porphyry and adjacent metamorphosed sediments. 5) Disseminated ore is found in altered porphyry and adjacent metamorphosed sedimentary rocks. 6) In general, there is a direct correlation between grade of ore in porphyry and copper content in the adjacent rocks. 7) Chemical changes in the altered porphyry and metamorphosed rocks appear to be related. The foregoing relations support a hypothesis that the porphyry alteration, the metamorphism of the sedimentary rocks, and the ore deposition were all part of a continuous hydrothermal process which probably closely attended the porphyry intrusion. The Robinson Mining District, most often referred to as the Ruth or Ely District, is located in eastern Nev. and is one of the major porphyry copper districts of the world. Production from 1908 through 1962 was nearly 250 million tons of ore averaging a little over one percent copper with a total metal value of nearly one billion dollars. The ore has been produced from six major disseminated-type deposits with the Liberty Pit deposit accounting for 70% of the total district production. Less than one million tons of base metal and gold ores have been produced from the replacement-type deposits of the district. Approximately 20% of the district production has come from underground mining operations; the pit ore has been mined with shovels and removed by train haulage, truck-train haulage combinations, truck haulage, and presently by a combination truck-skip system. Many of the ore deposits formerly worked by underground methods have been and are being exploited by open pit methods. (See Fig. I.) Two co.&apos;s have accounted for virtually the entire production from the district. In 1958 Kennecott Copper Corp. acquired the district assets of Consolidated Coppermines Corp. and is now the sole ore producer in the district. Present operations are confined to the Liberty Pit where 22,500 tons of ore averaging a little less than 0.8% copper is mined per day. Cutoff grade is 0.4% copper, and the stripping ratio is three to one. The ore is hauled by rail 23 miles to the McGill Reduction Plant where it is concentrated to about 20% copper. Molybdenite is recovered as a by-product in the mill. The copper concentrates are smelted in McGill, and the blister copper is shipped for refining to Balt. where gold, silver, platinum and palladium are recovered. The Robinson Mining District has been well known as a porphyry copper district for the past fifty years, but many geologists are unaware of the fact that a large portion of the production has come from disseminated ore found in metamorphosed sedimentary rocks. The scope of this paper describes the occurrences of disseminated ore in the various metamorphosed sedimentary rocks, and presents evidence for the hypothesis that these ores are genetically, spacially, and coevally related to the disseminated ore in the porphyry rocks. Publication of this paper was granted by the management of Kennecott Copper Corp. A. H. James suggested and encouraged the writing of the manuscript. Special mineralogical and spectrographic analyses were performed by the Kennecott Research Center. The deposits of the district have been studied by many geologists since the turn of the century, and

Jan 1, 1964

By Oliver B. Hopkins

Peru produced approximately 15,838,610 bbl. of oil during 1938, which was 1,618,406 bbl. below its production during 1937. As in recent years, the entire output of the country came from the La Brea-Parinas, Lobitos-Restin, and Zorritos fields, which are all situated along the northwestern coast. Outside of the proven areas, the drilling of test wells was continued by the Peruvian Government on the reserved zone near Zorritos. Six wells have been completed or are drilling. Of these one is a gas well at 2619 ft. and one is dry at 1415 ft. It is reported that three standard and two rotary rigs are being used. In southern Peru, in the Pirin region north of Lake Titicaca, the Government made a geological study of the National Reserve. In eastern Peru, the Cia. Petrolera El Ganso Azul continued its activities in the montana region, where its first well was reported to have had a show of oil at 1000 feet. There was also renewal of leasing activity in eastern Peru, where approximately 380,000 acres of new leases were filed on near Contamana. La Brea-Parinas Estate.—Production of crude oil on this property of International Petroleum Co. Ltd. amounted to 13,137,988 bbl. which was

Jan 1, 1939

By Oliver B. Hopkins

Peru produced approximately 15,838,610 bbl. of oil during 1938, which was 1,618,406 bbl. below its production during 1937. As in recent years, the entire output of the country came from the La Brea-Parinas, Lobitos-Restin, and Zorritos fields, which are all situated along the northwestern coast. Outside of the proven areas, the drilling of test wells was continued by the Peruvian Government on the reserved zone near Zorritos. Six wells have been completed or are drilling. Of these one is a gas well at 2619 ft. and one is dry at 1415 ft. It is reported that three standard and two rotary rigs are being used. In southern Peru, in the Pirin region north of Lake Titicaca, the Government made a geological study of the National Reserve. In eastern Peru, the Cia. Petrolera El Ganso Azul continued its activities in the montana region, where its first well was reported to have had a show of oil at 1000 feet. There was also renewal of leasing activity in eastern Peru, where approximately 380,000 acres of new leases were filed on near Contamana. La Brea-Parinas Estate.—Production of crude oil on this property of International Petroleum Co. Ltd. amounted to 13,137,988 bbl. which was

Jan 1, 1939

L. S. PANYITY.-I made inquiries from the Smith and Dunn people, who are the originators of the compressed air and gas method of increasing the production of oil wells, as to how much pressure the sand will stand; that is, relative to the original rock pressure. They tell me that they have not been able to show, up to date, any pressure in a sand greater than the original pressure. I have also made &apos;a statement to that effect, but I am really dubious as to whether that is right, as I am not sure that you cannot get a greater pressure. However, I think that a greater pressure would be dangerous because it might cause a loss of gas. C. H. SHAW, ? Lawton, Okla.-In regard to the gas that was put into the pool up in New York State, may it not be possible that, on account of errors, etc., in measuring or computing, there is a mistake in the apparent fact that more gas was gotten out than was put in? L. S. PANYITY.-Unfortunately, I have not the papers I expected from those people to show the actual conditions, but I do not doubt that such

Jan 4, 1919