Search Documents

WHEN pouring concrete it frequently happens that space prohibits the placing of a mixer at the point, or points, where the concrete is to be used. Usually in such cases recourse is had to some form of pressure chamber, or concrete gun, to blow the mix by compressed air from the mixer to the point of pouring. Recently such a case arose at one of the western mines. The experience obtained there may be of benefit to others, not expert in the means of transporting mixed concrete, when they run up against similar situations. The first stage in pouring in this instance was a vertical drop of 100 ft. from the mixer on one level to the point where horizontal travel began on a lower level. Standard 6-in. pipe with flange joints was used, hung in the shaft space available. A standard 45" bend near the bottom directed the mix, with free discharge, into an air chamber for the horizontal stage of travel. With an air chamber at the mixer and pressure applied to the falling mix in the vertical section, jamming frequently occurred at the turn and the pipe would have to be taken apart for freeing. To obviate this difficulty the mix was poured slowly without the addition of air pressure, when it was found that the mix got through much better.

Jan 1, 1929

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By Maxwell Adams

CONSIDERABLE interest has recently been developed in sage-brush oil because of its possible utilization as a flotation agent in the mining industry. A list of some of its physical properties, together with the method used in its extraction, may prove of interest at this time. Something over a year ago, a study of the essential oils in desert plants was begun in the Chemical Laboratory of the University of Nevada. None of the oils so far studied possess properties of special interest to engineers, except the oil of sage, Artemesia tridentate, which has exceptional power as a flotation agent. This plant, known as common sage brush, also called black sage, is widely distributed over the semi-arid West, being found quite generally on most of the dry plains and mountains west of Missouri. The method of extracting the oil followed in these experiments is very simple. The leaves, twigs and small branches are placed in an airtight drum, having a capacity of about 27 cu. ft. Steam is admitted through a number of small openings at the bottom of the retort, and the pressure maintained at 20 to 25 lb. per sq. in. for 3 hr. The escape of the steam from the retort is regulated by allowing it to pass through a stop-cock into a condenser. The water in the receiver is drawn off from time to time and the oil, which is insoluble and floats upon the water, is thus collected. At the end of 2 hr. most of the oil has been driven out, though traces continue to come over for a much longer time. By raising the pressure, the time required could probably be shortened and the yield increased, but the lack of laboratory equipment has prevented the carrying out of this experiment.

Jan 9, 1916

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

Jan 1, 1915

By M. T. Simnad, C. E. Birchenall, M. H. Davies

THE marker movements observed by Davies, Simnad, and Birchenall during the growth of magnetite on wustite have been misinterpreted. It is the purpose of this note to correct the original interpretation. In that investigation wustite specimens were prepared by oxidizing pure iron disks in water vapor until the iron was consumed. Argon was used as a carrier gas for the water vapor and on the complete conversion of the metal to its oxides ('FeO' plus a small amount (10 pct) of surface Fe3O) the water supply was bypassed and the specimens were annealed in argon alone in order to equilibrate the wustite with the overlying magnetite. After cooling, the magnetite was ground off, a crude magnetic test being employed to determine its complete removal. Radioactive silver streaks were then applied to the surface and the specimen was oxidized completely in water vapor to prevent hematite formation. After complete oxidation the markers were found to enclose about 80 pct of the magnetite with the other 20 pct lying outside the markers. This observation was interpreted to mean that oxygen transport was four times as great as iron transport during the growth of the magnetite. The conclusion would have been correct if, as in the case of wustite growing on iron, all the iron had started from one side of the marker and all the oxygen from the other side initially. Actually a material balance is required. For simplicity, take wustite to be exactly FeO, and magnetite to be Fe3O,. Then at the start of the reaction 3 FeO + O -> Fe,O., All of the iron and three-fourths of the oxygen of the final product will be within the marker inter- faces. The other fourth of the oxygen is in the gas phase outside the marker. From the experimentally determined final position of the markers simple calculation shows that one-fifth of the total iron has crossed the marker interface, while one-twentieth of the total oxygen has crossed in the reverse direction. The simplified result favors iron transport in the ratio four to one. However wiistite is not stoichiometric FeO. At 900°C, the temperature of the measurement, the composition is about FeO When the material balance for the same experimental result is repeated, assuming the product will be 1 mol of Fe3O4, it is found that 0.6 gram atoms of iron and 0.19 gram atoms of oxygen must have passed the marker in the same direction. (This is readily apparent from the reaction to form 1 mol of Fe3O4 SFeO The total oxygen supplied from the atmosphere is 0.61 gram atoms, but the iron which passes the marker interface, i.e., 0.6 gram atoms, requires 0.8 gram atoms of oxygen to convert it to Fe,O,.) If all the transport during magnetite growth is due to iron ion diffusion, then the marker would enclose about 85 pct of the final magnetite and the original measurement is in error by about 5 pct. This error is probably less than the uncertainty in locating the markers by autoradiography. The possibility also exists that the starting wustite was not quite saturated with oxygen and underwent further enrichment with consequent envelopment of the marker before magnetite caught up with the marker interface. In any case it appears that these measurements actually favor iron ion diffusion in magnetite overwhelmingly as the factor controlling its growth, although further experimental measurements are needed to eliminate the error in material balance described. Such studies are planned.

Jan 1, 1954

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

COMMITTEES Committee on Arrangements DAVID H. BROWNE, Chairman BRADLEY STOUGHTON, Vice-Chairman LAWRENCE ADDICKS BURR A. ROBINSON PERCY E. BARBOUR E. MALTBY SHIPP GEORGE D. BARRON JOSEPH STRUTHERS J. V. N.. DORR E. B. STURGIS J. R.. FINLAY T. T. READ Louis D. HUNTOON R. H. VAIL

Jan 4, 1916

By James A. Burns

The challenge to designers of bulk materials handling systems is to apply the existing technology in areas where it has not been used and to foster better, cheaper and safer job performance. The Dashaveyor Co., a subsidiary of The Bendix Corp., built and tested a pilot system at Copper Range&apos;s White Pine mine. Based upon this success, a prototype system development was begun in 1967 to test the concepts in a full-scale, realistic environment.

Jan 11, 1973

By C. M. Means

Considering the hazard involved in mining operations, statistics show that a very small percentage of accidents is chargeable to electricity. These accidents do represent quite a large percentage of those that are preventable and they are the direct result of the introduction, for purely economical reasons, of a dangerous element. The introduction of electricity in mines should decrease the hazard, and in no case should electricity be applied to the mechanical operation of equipment if by so doing the dangers incidental to mining are increased. The greater number of accidents are the result of persons coming in contact with exposed conductors at potentials varying from 258 to 508 volts direct current. The use of alternating current at higher potentials than these is quite common in large mines, but it is very rare that an accident happens from this source. This is explained by the fact that where these high voltages are warranted, proper precautions are taken, and the installations are directed by those who fully appreciate the dangers incidental to the work. Direct current is in much more general use than alternating current because of its adaptability to haulage locomotives and the low cost of installation in small operations. We are, however, coming to a more extended application of alternating current for the operation of mechanical devices used in connection with mining. Our underground direct-current wiring system is an evolution from the surface trolley and feeder systems. This is probably due to the fact that our earlier successful applications were electric locomotives, which required the use of a trolley wire. The trolley current has been almost banished from industrial establishments on the surface because of the hazard involved, yet we use it indiscriminately underground, where the dangers from accidental contact or fire are infinitely greater., This does not mean that the underground trolley systems should be eliminated, but it does imply the proper safeguarding of such equipment as is necessarily a part of the trolley systems. It is a fact that the men now employed in the installation and maintenance of mining equipment may be in many cases incompetent or not thoroughly familiar with the work, but they are the men who must do the work and, in order to do it properly, it is necessary that they be educated

Jan 1, 1915

By G. S. Brooks

The tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high tempera tures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3 This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations oil a commercial scale are contributed: I. Physical Properties of Zinc Ferrite. As formed for the most part synthetically by investigators, zinc ferrite exhibits characteristic physical properties, such as octahedral crystals, dark color, and a density over 5, together with a slight magnetic attractability. In examining with the microscope many products of mechanical muffle-roasting kilns, it is, however, impossible to find individual grains which can be identified as consisting entirely of zinc ferrite. The variety of colors, especially where each grain of blende was mechanically free from marcasite, rather conveys the impression of a partial ferritization of the grain. One side or end, for example, may often have the hard, dense surface and dark red to black color of the ferrite, while the balance shows the usual light yellowish brown of a normal iron-free blende.

Jan 1, 1914

By E. F. Loiseau

In a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it mas expected that a plan devised by Dr. Charles N. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee&apos;s sale, and the oven was modified, according to Dr. Cresson&apos;s plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust nixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one half of the lumps produced by the press. The plan mas abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is usually dry pitch, which is prepared by separating from the tar, at a temperature of 572&apos; Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392&apos; Fahrenheit. But with common tar very weak fuels are obtained, which do riot burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By Persifor Frazer

COMPARATIVE columns expressing the series of rocks of the lower half of the Mesozoic age in this country and in Europe are not yet definitely established. The following represents a co-ordination of the beds in England and Germany,* with a list of materials to be worked in from this country. † * Cotta, " Geologic der Gegenwart." † Section from York to Dillsburg. Report C, 1875; Second Geological Survey of Pennsylvania.

Jan 1, 1877

Jan 1, 1934

By C. L. Colburn

Discovery is the first step in the location of the claim. The provision of the Revised Statutes (2320) is, " No location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located." Strictly speaking, discovery may be defined as the finding of ore or metalliferous rock in place in a well-defined vein. This definition was too strict, so discovery extended later to cover such indications of the pregence of ore, within rock in place, as would justify an experienced miner in spending his time and money with a reasonable expectation of finding ore in paying quantities. According to Colorado statutes a discovery must show a well-defined crevice; in Arizona, a lode, deposit, or mineral in place; in Montana, a well-defined crevice or valuable depositi; in Nevada, a lode or deposit of mineral in place. It is wrong to require a discovery. An honest prospector, wishing to obey the law, finds himself compelled, in most cases, to evade this point. In Clear Creek district, Colorado, a quartz seam will constitute a discovery; in Butte, a red capping; in Leadville or Ely, it is any place where a man can find a piece of vacant ground big enough upon which to sink a . 10-ft. hole. If the vein or deposit outcrops a man can show a discovery, but if it does not outcrop it is foolish to compel him to show one; and this point has been gently side-stepped. Any hole 10 ft. deep now constitutes a discovery. It is no use having laws that the people cannot consistently ob_ey. No sane man will dig unless he expects to find mineral, and he should be protected while digging. He should be required to show that he has mineral ground only when he comes to patent.

Jan 1, 1915

By Oliver Bowles

SUPERFLUOUS varieties and standards which are meriting the critical scrutiny of the manufactur-ing industry have a special significance in the non-metallic mining industries, where, many of the final or intermediate products are manufactured at the mine or quarry. Such processes of manufacture must be considered an integral part of mining in its broader sense. Improvements may be either elimination or standardization. - The chief requirement of elimi-nation is an agreement between consumers and pro-ducers based on facts deduced from: statistical data. Standardization is much, more complex. Standards .may be established only when a very; thorough knowledge has been gained of the physical and chemical properties of the products, and the requirements of consumers. The activities of the Bureau of Standards are. largely directed toward such determinations. Paving-brick manufacturers, together with highway engineers, representatives of certain engineering socie-ties, and Government bureaus, have agreed that of the 66 styles of paving brick on the market 11 only are, essential and 55 are superfluous. Steps have been taken to reduce the output of -all but the 11 standard types. It is customary for manufacturers of structural slate to prepare it in sizes specified by builders and architects. Thus the material cannot be manufactured in advance and the result is irregular activity of mills, delays in filling orders, etc. To improve this condition, the Structural Slate Co. has issued a series of pamphlets giving complete specifications of structural slate for various purposes. Architects find it so much easier .to, order slate from these sheets that standard sizes are specified in preparing plans for new structures. Slate switchboards are usually manufactured after. the order has been received. One manufacturer claims that 80 per cent. of all switchboards are of standard sizes, and he keeps such sizes in stock. The facility with which orders may be filled from stock, and the improved quality of seasoned switchboards, will undoubtedly influence electrical, companies toward a more uniform standardization in size. Simplicity, could be further attained by the elimination of minor irregularities in .style; for example, in the beveled. edges.

Jan 2, 1922

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,&apos; is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951