Search Documents

Jan 1, 1920

By William J., Coulter

IN the early days of Colorado mining, between 1880 and 1900, when Leadville, Kokomo, and Robinson were boom mining camps, the entire area around Climax for a matter of fifteen miles was overrun with prospectors, so the mineralized outcrop at Climax was not unknown. The principal interest in minerals during this period was in gold, silver, and lead, and since the Climax outcrop showed none of these it drew little attention. Geology played an important part in bringing prospectors to the very edge of the Climax deposit. The Mosquito fault, which crosses near the base of Bartlett Mountain, continues as an important geological structure, at least as far as Leadville some twelve miles distant, and at the base of Bartlett Mountain the vertical throw on the fault is estimated to be between 2000 and 5000 ft. The sedimentary beds known to the Leadville district are all present on Bartlett Mountain to the north of the Mosquito fault, which cuts them off abruptly, and exposes the Pre-Cambrian rocks that underlaid them, so the prospectors, who were searching for gold, silver, and lead in the sediments

Jan 1, 1946

By Howard N. Eavenson

One who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regulation of some sort is needed if any stabilization is to be achieved and if the wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920—to the end of 1934—the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing of the high wage scale of that agreement, which soon proved to be an uneconomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

By Howard N. Eavenson

One who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regulation of some sort is needed if any stabilization is to be achieved and if the wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920—to the end of 1934—the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing of the high wage scale of that agreement, which soon proved to be an uneconomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

By AIME AIME

PAST President R. C. Allen, then State Geologist of Michigan, gave George Corless his first job-tracing ?magnetic? with the dip compass in northern Wisconsin. His second job was also with a man now Past President of the Institute-"Chief" Buehler, for whom he worked at Joplin three years. Then came seven years as geologist and later as assistant manager of the Chanute Spelter Co., a subsidiary of The American Metal Co., Ltd. His entrance into the oil business was not planned. During a lull in the zinc industry in July, 1926, he stopped at Houston, after a trip to the Rio Grande Valley, and was so impressed with the city that he decided to migrate. His first job there was with the Texas Company, whose impressive building across from the Post Office caught his eye after he had mailed a letter saying that he was settling in Houston and would not be home until Christmas. Some months later, A.I.M.E. Past President Philip N. Moore learned that he was in. Houston and wrote an unsolicited recommendation that resulted in his present employment with the Humble Oil & Refining Co. Today he is superintendent of the Gulf Coast Division of its production department. The Division extends from Jackson County, Texas, to New Orleans, and includes such pools as Sugarland, Conroe, Toni Ball, Thompsons, Anahuac, and Friendswood. -

Jan 1, 1938

By J. F. Ednie

SCRAP metals to the value of more than a billion and a half dollars were recovered in the United States in 1939 for further use in industry. Few people have any true conception of the magnitude of the secondary-metal industry as related to that engaged in the production of the primary, or virgin, metals; of its importance, particularly when a shortage of primary metals exists, as at present; or of the advance that has been made in standardizing and improving the quality of its products. Of the iron and steel produced in the United States in 1939 (the data used in this article are largely taken from Bureau of Mines reports for that year) just over 50 per cent came from scrap and slightly less than 50 per cent from ore. Of the principal nonferrous metals-aluminum, anti-mony, copper, lead, nickel, tin, and zinc-63 per cent came from domestic ores and 37 per cent from scrap. Fig. 1 presents graphically the relative tonnage and value of primary and secondary production of ferrous and nonferrous metals. In this chart only purchased secondary metals are considered, the figures being exclusive of "home" or "plant" scrap which amounts to rather large figures in the iron and steel industry. Incidentally, the chart shows that from the tonnage standpoint the iron and steel industry is some twenty times larger than the nonferrous industry, though with regard to the value of the product the ratio drops to about two to one.

Jan 1, 1941

By Gilbert H. Cady

Those coal mining and preparation engineers and operators who read this article will probably be most concerned with those parts which deal with the applied aspects of coal petrology in the fields of mining and technology. Actually the two categories overlap to such a degree that they are essentially one. The article appears to suggest that there are two points of veiw in the field of applied coal petrology. From one viewpoint the interest is in the attributes of the various macerals (Fig. 4)-vitrinite, exinite, and inertinite-in terms of utilization (when the coal is burned, coked, gasified, hydrogenated, etc.). From the other point of view, assuming that the macerals do possess individuality in behavior, interest attaches to the possibility that coal of a particular type (maceral composition) can be prepared by discriminating methods of preparation and blending. Most of the 29 items listed for mining and technology can be assigned to one or the other of these two categories.

Jan 5, 1958

By H. H. Campbell

The following pages discuss some problems connected with the manufacture of steel by the open-hearth process. The methods employed necessarily enter into the domain of what is called theory; but the results are eminently practical. The determination of the various losses of thermal power and the investigation into the chemical reactions in the bath, are important to every manufacturer. It will be understood that definite figures concerning one furnace and one system, will not apply to all other furnaces and systems; but it is hoped that methods are developed, which are capable of general application and which will shorten the labors of others. The gas-calculations contain nothing entirely novel; but certain methods appeared to be very convenient and they are here elaborated in order that others may have a model to follow. The determination of the loss of iron by weighing the slag and finding the percentage of iron therein, is probably unusual. If so, the fact is to be regretted, since this is the only way that an accurate result can be obtained. The common method of estimating the loss in open-hearth work, is to subtract the weight of metallic products from that of the materials charged. Nothing could be more unsatisfactory, inaccurate and meaningless. Pig-iron, steel, wrought-iron and ore are charged into the furnace; complicated chemical reactions occur; the sand of the pig-iron, the slag from the wrought-iron, the gangue of the ore, all rise to the top ; the silicon, manganese and carbon burn and leave the metal; some of the iron oxidizes and goes into the slag; some of the ore is reduced and gives up metallic iron ; the recarbonizer is added, the mission of which is to waste itself; in the pouring of the steel, pit-scrap is made in the ladles, around the moulds and under the spout; the errors in weighing the products join hands to make accuracy impossible; and then the " loss" is determined by diffrence !

Jan 1, 1891

By Lester C. Uren

Petroleum occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock1' into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 1, 1925

By David White

THE environmental conditions under which coals are deposited are revealed by the stratigraphy of the coal basins and coal beds and by the details of the structure and the physical constitution of the coals themselves. THE LAND SURFACE Generally Low Relief or Base Level In the Paleozoic coal fields, which have longest been worked, are most important, and are best known, we find relations, in general, as follows A post-Mississippian uplift with, in most cases, very moderate deformation, followed by erosion by which the uplifted regions, especially the bolder of the new topography, were largely worn down, while the older and less deformed regions were more or less extensively base leveled. Base leveling of most of the region continued as the deposition of coal measures proceeded. Consequently, in most coal fields the Pennsylvanian, or upper Carboniferous, lies unconformably on the Mississippian or on older formations. There are but few regions in which sedimentation is seen to have been apparently continuous from the Mississippian into the Pennsylvanian ("Coal Measures").

Jan 1, 1925

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By John E. Sherborne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons.l-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applications of phase behavior have been made to specific cases pertaining to critical phenomena.l2-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. Definition of Terms In a discussion of this sort, a definition of terms used is most important. Such terms as "pressure," "temperature" and "volume" need little definition other than mention of the units in which they are considered. Pressure is expressed in pounds per square inch absolute. Temperature is usually expressed as degrees Fahrenheit or degrees Rankine. In considering thermodynamic and phase behavior, the use of the absolute, Rankine, scale is desirable. Volume is expressed as specific volume, such as cubic feet per pound. This will be recognized as the reciprocal of the specific weight. In considering systems composed of more than one component, it is sometimes desirable to consider molal

Jan 1, 1940

By John E. Sherborne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons.l-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applications of phase behavior have been made to specific cases pertaining to critical phenomena.l2-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. Definition of Terms In a discussion of this sort, a definition of terms used is most important. Such terms as "pressure," "temperature" and "volume" need little definition other than mention of the units in which they are considered. Pressure is expressed in pounds per square inch absolute. Temperature is usually expressed as degrees Fahrenheit or degrees Rankine. In considering thermodynamic and phase behavior, the use of the absolute, Rankine, scale is desirable. Volume is expressed as specific volume, such as cubic feet per pound. This will be recognized as the reciprocal of the specific weight. In considering systems composed of more than one component, it is sometimes desirable to consider molal

Jan 1, 1940

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By Werner Joseph, Richard R. Knobler

When the first batch of refined copper ingots was cast at Mantos Blancos in January 1961, eight years of exploration, development and metallurgical pioneering by Mauricio Hochschild & Co. had come to a successful conclusion. This Chilean copper deposit, located in the Atacama Desert 30 miles from Antofagasta, is now producing approximately 20,000 tons of copper per year. The Mantos Blancos deposit has been known since 1912 and various attempts had been made to work the high-grade zones before the present operation was started. The major drawback of the ore to any previous development was its chloride content which varies between 0.4% and 1.5% C1. Although the chloride ruled out the conventional leaching-electrolysis scheme, it did lend itself to the process of precipitating the copper as cuprous chloride.

Jan 1, 1962

By T. F. Bower, M. C. Flemings, H. D. Brody

A series of experiments are reported which show thai reasonable assumptions for analysis of solute redistribution in solidification of castings and ingols illclr(de: negligible undercooling before nuclcation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the Liquid oer distances the order, of dentrite arm spacings, platelike dentrite t/o?$holog?.. Qzmli/ali,e and periment is obtained JOY Al-Cu alloys front measurements of amount of nonequilibrium second phase, minimum solute content at the centers dentrites arms (after solidification), and 3) change in minimum solute content in dentrite arms during solidification. In a previous paper' analyses were given describing solute redistribution in dendritic solidification. The analyses were undertaken primarily to permit prediction of "severity of microsegregation" in a casting or ingot after solidification and cooling to room temperature, but can also be used to predict "local fraction solid' as a function of temperature in the solidifying alloy. Numerical results were given for Al-Cu alloys. The aims of this paper are to examine the validity of some of the assumptions of that analysis, and to compare predictions of the theory with experiments. All experiments reported are on Al-Cu alloys, the bulk on Al-4.5 pct Cu alloy. EXPERIMENTS Experiments conducted were on small ingots, 41/2 in. in diam by about 10 in. high. solidified in a controlled thermal environment (i.e., in a resistance-heated, re-circulating air furnace, whose temperature could be controlled to 1°C). In one series of experiments, the ingots were solidified very slowly (solidification time was varied from 8 to 1000 hr) and at constant rate of heat extraction. In a second series of experiments the ingots were solidified ( 'unidirectionally". Fig. 1 is a sketch of the method of making the two different types of ingots. The unidirectionally solidified ingots were fully columnar, and the slowly solidified ingots had equiaxed structures, Fig. 2. In making the slowly solidified ingots, the mold employed was carbon steel, coated with inert refractory. Typically the mold and its environment were heated to 700°C. The molten alloy was then poured into the mold and the temperature of the system equilibrated above the liquidus. The environment of the mold was next cooled with a controller responding to a differential thermocouple that measured the difference between the temperature of the melt and the temperature of the mold environment. The differential thermocouple consisted of one chromel-alumel junction in the melt connected in opposition with a second junction in the furnace. The potential across the differential thermocouple was input to the controller which acted to keep this potential at a set. constant value; hence the temperature difference between the two junctions was maintained nearly constant. Major resistance to heat flow in the above apparatus was between the metal surface and the furnace atmosphere, not in the metal itself. By maintaining a constant temperature difference between the metal and the furnace atmosphere, the controller maintained an essentially constant rate of heat extraction during solidification, regardless of amount of heat released by the metal per unit temperature change. When the metal temperature dropped just below the eutectic temperature. the ingot was removed from the furnace and water-quenched. The unidirectionally solidified ingots were cast in a similar mold to the foregoing except that provision was made to extract heat through the bottom face of the mold by passing air or water through the mold base, Fig. 1. For these experiments, metal and mold temperature were again equilibrated above the liquidus. Temperature of the mold environment was then held

Jan 1, 1967

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,' is believed to account for the thermal hardening observed by Blank'" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author's reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,' it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

By J. C. Scully, G. Sanderson

The electrolytic formation of y hydride in thin foils of Ti-5Al-Z.5Sn alloy and four Ti-A1 binary alloys has been studied by electron microscopy and electron diffraction. Two orientation relationships have been found: THE adsorption of hydrogen by titanium alloys from aqueous solutions has been widely reported. This can occur, for example, in both alkaline' and acidic2 pickling baths, in chemical polishing374 and electro-polishing Solutions,3,4 during cathodic polarization5" and under certain corrosion conditions,7,8 Etching reagents may also produce visible precipitates, sometimes after an aging period.9 During an investigation into the stress corrosion susceptibility of a titanium alloys by thin foil electron microscopy many observations have been made of hydride precipitation which has been deliberately promoted by techniques that are described below. The characteristics of hydride precipitation are reported and the observed crystallographic orientation relationships are discussed with reference to distortion in the titanium lattice created by the presence of the hydride. EXPERIMENTAL TECHNIQUE One grade of commercial titanium and five alloys were examined. Their composition and hardness values are shown in Table I. All the materials were in the form of thin sheet, 0.05 to 0.065 cm thick, which had been annealed after cold rolling. Foils suitable for transmission electron microscopy were made in two ways: a) by chemical polishing; and b) by elec-tropolishing. The solution used for chemical polishing was a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. During this polishing specimens were manually moved up and down in the solution. The reaction was veFy rapid, specimens thinning to foil thickness (2000A) in 5 min. Since chemical polishing solutions tend not to cause hydride contamination if they are kept cool3 no attempt was made to prevent the solution from becoming hot during the thinning operation. Electropolishing was performed at -30° C with a mixture3 composed of 295 cu cm methyl alcohol, 175 cu cm n-butyl alcohol, and 30 cu cm perchloric acid with an applied voltage of 40 v after chemically thinning specimens to approximately 0.017 cm thickness in a cool solution of 44 pct HF, 40 vol H2O2, and water in the volumetric ratio 1:6:3. EXPERIMENTAL RESULTS 1) Ti-5A1-2.5Sn Alloy. The Ti-5A1-2.5Sn alloy was severely contaminated by hydrogen during the chemical polishing. Foils obtained in this way contained large amounts of the y hydride phase. A typical micrograph is shown in Fig. l. The laths were identified as the hydride phase by selected-area diffraction of a large number of foils examined in a tilting stage that could be turned through 40 deg. Using the lattice spac-ings of the alloy obtained by X-ray diffraction as a standard the a value of the hydride was determined fromo the electron diffraction patterns to be 4.38 to 4.40A. The accuracy of this figure is only about ±2 pct. Further evidence of the identification was obtained by vacuum annealing chemically polished foils of the alloy at 500°C. This resulted in the dissociation of the hydride with the production of dislocations and possibly vacancy loops as shown in Fig. 2. The hydride

Jan 1, 1968

By H. K. Najarian

This paper describes recent development work on the Wheaton-Najarian Vacuum Condenser for Zinc at Josephtown Zinc Smelter, wherein, to dissipate the heat of condensation, the "airlift" action of gases bubbling through the molten zinc in the condenser is utilized to circulate the zinc through an outside "cooling well" and cooling it continuously. AN earlier paper1 gave an account of initial development of the Wheaton-Najarian Vacuum Zinc Condenser at the Josephtown Zinc Smelter of the author's company. This paper is a progress report of further development work over the years directed toward improving the efficiency and increasing the capacity of the condenser. In this type of zinc condenser, zinc vapor with accompanying noncondensable gases from electro-thermic zinc smelting furnaces is passed upwardly through a mass of molten zinc confined in a refractory-lined U-tube. The zinc vapor condenses in the molten zinc and the noncondensable gases are drawn out of the condenser by suction applied over the surface of the molten zinc. The heat of condensation of zinc, amounting roughly to 1000 Btu per lb of zinc condensed, is absorbed by the molten zinc and, in turn, is dissipated continuously to keep the temperature of molten zinc in a range to permit effective condensation. At the time of publication of our first paper, we had at Josephtown Smelter five units of 69-in.-bore metal furnaces and one larger metal furnace having 96-in. bore. Each 69-in. metal furnace had a condenser with 22-ft overall length. The 96-in.-bore furnace had a condenser with overall length of 31 ft. Condensers were of circular cross section, with corrugated steel outer shell and carborundum lining. Diameter of these condensers was 32 in. inside the refractory lining. Molten metal in the con- denser was kept cool by spraying cold water on the outside of the condenser shell. Under good operating conditions, 22-ft condensers produced some 12 tons of metal per day; and the 31-ft condenser, about 22 tons. When the furnaces produced zinc vapor at higher rates, invariably the condenser temperature would rise to levels where excessive blue powder would form and accumulation of accretions in the condenser would be accelerated. We found that, with the system of cooling in use, we had to provide heat-exchange surface of some 150 sq ft to condense 1000 lb of metal per hr with reasonable efficiency. The wall of the condensers was made up of 5/8-in.-thick corrugated-steel shell having next to it several layers of mica and inner refractory lining of special carborundum shapes to fit the corrugation in the steel shell, and having a minimum thickness of about 2 in. Relatively low rate of heat transfer through the thick condenser wall and slow internal circulation of the molten zinc limited the rate of heat exchange between hot metal within the condenser and the cold water flowing over the outer steel shell. The thickness of the condenser wall was about minimum that we considered suitable for continuous operation. As we learned to operate the electrothermic furnaces with higher power input, producing zinc vapor at higher rates, it became apparent that we needed condensers having larger heat-exchange surfaces. Our 96-in.-bore furnace had 6 single-phase power circuits with transformers rated at 500 kva each and normally good for power input of 3000 kw.

Jan 1, 1959