Search Documents

By C. D. King

The advances in basic open-hearth practice which have occurred during the past decade have been principally in the direction of the physical development of larger units, decreased fuel consumption and increased length of furnace campaigns. However gratifying the economies which have resulted from these improvements are, it must be granted that like advances in chemical, physical-chemical and metallurgical knowledge pertaining to open-hearth practice would have added greatly to these already attained reductions in costs and it is the purpose of this paper to stimulate the discussion and study of these phases of cooperation and their relation to ingot yields. Definition and Calculation oF Losses In discussing basic open-hearth yields, the writer refers to the ingot yields obtained in the process of converting pig iron, scrap and ore to steel. In this conversion some scrap is produced. The difference between the total weight of ingots and scrap produced and the original metallic charge constitutes the loss. Basic open-hearth yields vary considerably, and while some of the divergencies can be explained metal-lurgically because of differences in slag analysis, proportion of pig charges, and character of steel made, there often remain differences that apparently do not readily disclose themselves. In reconciling yields by the usual accepted methods of calculation, one is often forced to evaluate large losses as ((unaccounted for." Such a system is prone to accept these large losses as inherent to the operat.ion and not, susceptible of appraisement and correction. It is obvious that if the ingot yield plus the scrap recovered subtracted from 100 per cent. determines the loss, a drop in yield may increase the loss or the scrap, and both contribute to a monetary loss. To be sure, one can subdivide these unaccounted for losses into various components, such as metallics in slag, free Fe in slag, spillage, etc., and thereby reduce the amount of losses considered as "unaccounted for." If empirical methods could indicate with some degree of accuracy all losses, however slight, the undetermined losses become appreciably smaller and resultant calculations will check actual

Jan 1, 1929

By F. H. Parsons

At the time that converting or bessemerizing of copper matte first began to be practiced by the smelters in the copper industry, converters were lined by tamping the flux, usually siliceous ore, into the steel shell. About 1910, practice in several plants had demonstrated the superiority of a basic lining of nonfluxing material and the addition of flux through the mouth of the converter. Adoption of the new method by nearly the entire industry followed. Basic linings are made of refractory "magnesite" brick manufactured, usually, from imported dead-burned magnesite. Either the linings are laid up in the shell dry or the bricks arc bonded with some mortar dictated by the preference of the user. Foreign, usually Austrian, magnesite was the main source of supply for these bricks, although there were domestic sources, but it was not until costs began to rise a few years after the first use of basic linings that these domestic sources were investigated to any great extent. Exigencies created by the World War necessitated the use of the domestic magnesite during this period, but the brick manufacturers reverted to the use of the foreign product after the war, because the impurities therein made a brick with a better fire bond than the purer domestic magnesite. Therefore the domestic product became available at a favorable price for any metallurgical process that permitted its use. The United Verde converting practice using magnesite linings has resulted in a high consumption of magnesite because of the zinc content of the low-grade matte. It was realized that the cost of these linings represented a large portion of the cost of converting, and an investigation was started to find means by which these costs might be lowered. In the neighboring state of California rather pure magnesite was being mined and treated for the market. The product, however, was purposely made to simulate the dead-burned grain magnesite product from foreign sources by the addition of fluxing impurities before burning. It was learned that this dead-burned California grain magnesite could be laid down in Arizona at a price one-third that of the same tonnage of "magnesite" brick manufactured from foreign magnesite. It was also learned that at least one California producer was ready to supply the market with periclase, which was a grain magnesia produced by burning the

Jan 1, 1934

By B. Silliman

The experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phœnixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 21o F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so constructed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care-

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By Robert Anderson

OLIVER C. RALSTON, Salt Lake City, Utah- (communication to the Secretary *).-The literature on the theory of flotation has been enriched, of late, by the views of a number of excellent mining engineers who unfortunately were tyros in physical chemistry and physics. Hence the obscurity and mystery with which the process is supposed to be surrounded. The present paper goes far toward explaining some of the ideas which have seemed obscure or which have been poorly expounded by the men who advanced them, but there are a number of places where the author's explanations are unsatisfactory, or where he has fallen into the same mistakes made by the original propounders of the theories involved. While recognizing the value of constructive compilation, it is nevertheless disappointing to find a paper reviewing the recent theories of flotation which presents nothing-new-not even a new viewpoint. At the bottom of page 1121, there are stated to be present the following "phases" in flotation: "solid-liquid (ore-water), solid-liquid (ore-oil), solid-gas (ore-air)," etc. The writer could not possibly have meant to apply the word "phases" to the ideas involved. Each of the pairs of phases mentioned has an interface in which exists the interfacial tension that he is talking about.

Jan 12, 1916

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled sloping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill sloping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per scope unit, experiments with horizontal cut-and-fill scopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By J. L. Brimhall

Slip-line formation during bending has been studied on neutron-irradiated molybdenum single crystals. For equivalent strains, the slip lines are coarse and distinct in the irradiated molybdenum and not resolvable in the unirradiated molybdenum. The slip lines have been directly correlated with dislocation channels present in the irradiated and deformed thin foils. The heterogeneous distribution of the dislocations during deformation in the irradiated material results from dislocation interaction with the dejects produced during irradiation. Impurities , in the form of' carbides, affected the dislocation channeling Principally by acting as dislocation sources. ALTHOUGH the mechanical behavior of irradiated materials has been studied extensively, the precise mechanism of irradiation hardening has not been established. Some information on the microstructural species responsible for hardening of irradiated materials has been derived from direct and indirect observations. The direct observation of the structure of deformed irradiated metals, particularly by transmission electron microscopy, is a relatively new and unexplored area. Slip-line studies in fcc metals have been restricted primarily to copper.1-3 Very coarse slip lines, representing slip on many closely spaced planes, have been observed in deformed, irradiated copper. Coarse slip lines have also been observed in irradiated aluminum.4 Clear channels in irradiated copper caused by dislocation motion through the defect structure have been seen by transmission electron microscopy and correlated with slip lines.5-6 To date, little work has been reported on the irradiated bcc metals. Eyre described the slip lines around hardness indentations on irradiated iron and found them to be more distinct than lines in unirradiated material.' Mastel et al.' have observed channels in deformed irradiated molybdenum similar to those reported in copper. As part of a program concerned with the effect of neutron irradiation on metals, the slip-line

Jan 1, 1965

By H. C. Miller

The gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air-lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas-lift possible, or where natural gas is plentiful and inexpensive. We find, therefore, in California, that natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanies the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the tubing and flow lines. The gas-lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible, to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecrans field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas-lift at approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1928

By Arthur Gates

INTRODUCTION RITTINGER'S law of the energy expended in crushing is, as roughly stated by Professor Richards,1 that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product-assuming that all the mass has been reduced to one exact size, which is only theoretically possible.?2 Kick's law is stated by H. Stadler as follows:3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal -technological state varies as the volumes or weights, of these bodies." In other words, the energy expended is porportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1 -in. cubes at the first operation, and these are broken to 1/16 -in, cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 9, 1915

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through ¾ -in. to 0, and mixed sizes of ores down to 7/32-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and , flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although considerable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tentative conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way. As all really difficult problems in jigging arise from an attempt to treat a large range of sizes in one operation, nearly the entire discussion will be

Jan 1, 1943

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.O.b. mines, the output in 1948 was 1,-568,848 tons worth $19,756,738. Paradoxically, it seems in retrospect that the early failure of the American industry to meet foreign competition was due to the superior quality of our sedimentary clays in their natural state. Kaolin, of course, is the principal decomposition product of feldspars which originate in acidic igneous rocks such as granite, aplite, alaskite, granodiorite, quartz porphyry, etc. English china clays occur in residual deposits and before they can be marketed they have to be treated to remove accompanying quartz, mica, and other impurities. Notwithstanding the relatively crude methods employed, the final product is a beneficiated clay which is subject to a certain amount of technical control as to quality and uniformity. Although the naturally concentrated deposits in Georgia and South Carolina contain some of the finest crude white kaolin in the world, even it can be made better by suitable treatment. In recent years well over half of the high-grade china clay produced in the United States has been used in making paper. Some qualities of paper clays are still produced by the dry process, or air flotation, but the paper industry's specifications have grown so exacting that wet processing was adopted and more refined methods had to be perfected. Notwithstanding notable advances in clay-preparation technology during the past decade, or possibly because these advances have implemented and encouraged technologic changes in consuming industries, demand has grown for products of higher uniform quality than can be obtained from even the best natural deposits without rigidly controlled fractionation. Largely as a result of the wide adoption of machine coating for paper, the clay industry has been obliged not merely to eliminate virtually all mineral impurities but also to segregate the clay substance itself into narrow particle-size ranges. By extraordinary coordination of sales effort and production technology, several Georgia companies manage to market a wide variety of specialized joint products but the commercial success of many producers depends upon their mining only the best parts of their deposits and then skimming the cream of this almost pure clay in order to obtain a maximum yield of kaolinite finer than about 2 microns in maximum particle size and possessing low viscosity as well as the more familiar attributes of suitable color and brightness, or reflectance. To the casual visitor from another mineral industry, the kaolin mines and plants may appear to be

Jan 1, 1951

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.O.b. mines, the output in 1948 was 1,-568,848 tons worth $19,756,738. Paradoxically, it seems in retrospect that the early failure of the American industry to meet foreign competition was due to the superior quality of our sedimentary clays in their natural state. Kaolin, of course, is the principal decomposition product of feldspars which originate in acidic igneous rocks such as granite, aplite, alaskite, granodiorite, quartz porphyry, etc. English china clays occur in residual deposits and before they can be marketed they have to be treated to remove accompanying quartz, mica, and other impurities. Notwithstanding the relatively crude methods employed, the final product is a beneficiated clay which is subject to a certain amount of technical control as to quality and uniformity. Although the naturally concentrated deposits in Georgia and South Carolina contain some of the finest crude white kaolin in the world, even it can be made better by suitable treatment. In recent years well over half of the high-grade china clay produced in the United States has been used in making paper. Some qualities of paper clays are still produced by the dry process, or air flotation, but the paper industry's specifications have grown so exacting that wet processing was adopted and more refined methods had to be perfected. Notwithstanding notable advances in clay-preparation technology during the past decade, or possibly because these advances have implemented and encouraged technologic changes in consuming industries, demand has grown for products of higher uniform quality than can be obtained from even the best natural deposits without rigidly controlled fractionation. Largely as a result of the wide adoption of machine coating for paper, the clay industry has been obliged not merely to eliminate virtually all mineral impurities but also to segregate the clay substance itself into narrow particle-size ranges. By extraordinary coordination of sales effort and production technology, several Georgia companies manage to market a wide variety of specialized joint products but the commercial success of many producers depends upon their mining only the best parts of their deposits and then skimming the cream of this almost pure clay in order to obtain a maximum yield of kaolinite finer than about 2 microns in maximum particle size and possessing low viscosity as well as the more familiar attributes of suitable color and brightness, or reflectance. To the casual visitor from another mineral industry, the kaolin mines and plants may appear to be

Jan 1, 1951

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By S. Gilbert, G. R. Bailey

A further evaluation of the bomb-sampling method for determining the oxygen content of liquid steel is presented. The results of this study and their close agreement with the results of an earlier evaluation confirm the conclusion that the bomb-sampling method is valid for obtaining representative samples for the determination of the oxygen content of a liquid steel bath. WHAT constitutes the most desirable procedure for obtaining a sample suitable for determining the oxygen content of a liquid steel bath has been a controversial subject for several years. In 1952 Huff, Bailey, and Richards' described a modification of the bomb-sampling technique originated by McCutcheon and Rautio.' In both the modified and original techniques, a small cast-iron or steel mold containing aluminum wire and appropriately covered is inserted into the furnace, coated with slag, and then plunged into the metal bath. Upon entering the metal, the cover melts and a sample of the steel bath enters the mold. The data presented by Huff, Bailey, and Richards' indicated that reproducible samples could be obtained by their method. Furthermore, the oxygen analyses from samples obtained by their method agreed better with those from controlled laboratory experiments than did analyses from samples obtained by methods previously suggested for sampling large liquid-metal baths. Most techniques, other than bomb-sampling, require that a sample of liquid steel be removed from the furnace in a well slagged spoon and poured into an iron mold containing aluminum or into a massive copper mold for rapid chilling. Pouring in this manner requires that the sample pass through the air. The controversy, then, is somewhat as follows: Proponents of the spoon-sampling method and similar dip-and-pour methods feel that the introduction of a cold steel mold into a molten steel bath may result in a localized boiling condition that may deplete the steel of oxygen to a significant degree in the area where the bomb is introduced. Conceivably this boil could cause results that are, on the average, too low and nonrepresentative of the bath composition. On the other hand, samples that are spooned and then poured through the air may also be nonrepresentative because of oxidation by the atmosphere. The restrictions imposed in sampling with a spoon are much more stringent than those imposed when sampling with the bomb-type mold within the furnace. The spoon sample must be taken in a well slagged spoon, a requirement that depends on the condition of the slag in the furnace. Also, the samples must be poured as quickly as possible, without shaking the spoon and without allowing slag to enter the mold. The necessity of fulfill-

Jan 1, 1955

By C. R. McEwen

The displacement equations of Buckley and Lever-ett' have been successfully applied to the prediction of oil recovery in frontal drives for a number of years. Commonly, the capillary pressure term is omitted from Leverett's fractional flow formula. The resulting satura-tion-vs-distance curves become multi-valued, however. Buckley and Leverett, recognizing that the neglect of capillarity was most likely the cause, proposed that this part of the solution he ignored. An ingenious method of propagating a discontinuity in place of the multi-valued portlon of the curve was devised by Cardwell using "non-capillary displacement theory". However, it would seem that a completc description of the displacement pracess would require the inclusion of capillary forces. Three publications on displacement theory have appeared in which capillary pressure was included. Ter-williger. et al', calculated saturation profiles which matched those which they observed when gas displaced water vertically downward. Based on their study, Jones-Parra and Calhoun5 roposed a method of computing saturation distributions sufficiently removed in time from the initial conditions so that all saturations in the flood front region were assumed to move with the same velocity. This latter assumption corresponds to the tangent construction on the flowing fraction-vs-satura-tion curve proposed by Welge." A numerical solution to the problem of water displacing oil from a water-wet porous medium was recently presented by Blair, ef at'. The initial conditions included a uniform saturation slightly above interstitial water saturation. that is, the permeability to water ahead of the front was not zero. This appeared to result in a region of slowly rising water saturation ahead of the front, at least for the particular set of relative permeability and capillary pressure data used to illustrate the computation. The authors also postulated an "end-effect" at the outflow face of the system, whereby no water could pass out of the system until the water saturation had built up to a high value. The saturation profiles computed under these assumptions show water accumulating at the downstream end of the system while the flood front proper is still traveling toward the outlet. The purpose of this paper is to present the results of a numerical solution to the one-dimensional water-flooding equation in which no outlet end-effect is considered and where there is no flow of water ahead of the flood front. It should be noted that the contemporary paper of Fayers and Sheldon8 deals with the problem under discussion. For a thorough treatment including both capillarity and gravity the reader is referred to their paper.

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors' Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625' F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors' Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors' Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors' Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors' reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

By W. J. Maraman, D. R. Harbur, J. W. Anderson

A device for rapidly quenching liquid metals into thin platelets has been developed at the Los Alamos Scientific Laboratory. This rapid quenching equipment is built around the technique of catching a molten drop of metal between a rapidly closing plate and a stationary plate. The design and operation of this unit are described. The closing speed of the smasher plate at impact is 12.6 ft per sec. The quenching rate for this device is controlled by the interface resistance between the plates and the platelet, and is dependent upon the heat content and density of the material being quenched. The initial quenching rate down to the freezing point of the platelet material is lo5º to 106ºC per sec. After an isothermal delay, which is poportional to the heat of fusion of the platelet material, the final cooling rate down to the temperature of the smaslier plates is l04ºto 105cº per sec. RAPID heating of metals by capacitor discharge and other methods has provided the metallurgist with a useful tool for probing into the kinetics of phase changes and the many nonequilibrium phenomena which occur during rapid temperature changes. Equally interesting studies can also be made on metals and alloys which are rapidly cooled from the liquid state.' Studies in this field have been limited, however, because the rates at which metals could be cooled were many orders of magnitude slower than the rates possible for heating. In recent years many new laboratory methods have been developed to rapidly cool metals from the liquid state to ambient temperature and below.2"4 All of these methods involve spreading a liquid drop of metal into a thin foil in a very short time. The methods developed have varied from ejecting a drop of molten metal at the inside surface of a rotating cylinder or stationary curved plate to catching a falling drop of molten metal between rapidly closing plates. The equipment which has been developed at the Los Alamos Scientific Laboratory for rapidly cooling molten materials uses the latter of these two approaches. The basic design, operation, and initial results of this rapid quenching device are given in this report. APPARATUS The drop smasher, which is now being used to obtain rapidly cooled metal foils, is shown in Fig. 1. Basically the device consists of a smasher plate which is driven by a solenoid into a stationary plate. The solenoid is activated by a drop passing through the photoelectric cell and is powered by discharging an adjustable 350-v capacitor bank with a 66-amp peak current into it. This power supply is designed so that the solenoid is powered for 2 m-sec after plate closure to minimize the rebound effect. There is an adjustable time-delay mechanism between the photoelectric cell and the solenoid. Both smasher plates have changeable inserts so that a variety of materials can be used to smash the molten drop. The shaft of the moving plate is guided in an adjustable housing which has ball-bearing walls. The cabinet shown to the left of the drop smasher in Fig. 1 contains the power supply and receiver for the photoelectric cell, the time delay mechanism, and the capacitor bank. The drop smasher can be placed inside a vacuum chamber, for use with radioactive materials, with the upper plate forming the lid, as shown in Fig. 2. On top of the vacuum lid is an induction coil, powered by an Ajax induction generator, which is used to melt drops from the end of the rod extending through the vacuum seal on top the quartz tube. OPERATION The drop smasher shown in Fig. 2 is operated in the following manner. The smasher plates are separated and the unit is lowered into the vacuum chamber using a pressurized cylinder. The induction coil, quartz tube, and lid with sliding vacuum seal are then assembled on top the vacuum chamber. A rod of the material for rapid quenching studies is connected to the rod extending through the sliding vacuum seal. The vacuum chamber is then evacuated and the desired atmosphere established. The photoelectric cell is turned on, and the capacitor bank is charged and armed. Power is supplied to the induction coil, and the rod of material for rapid quenching studies is lowered into the induction field. A molten drop forms on the end of the rod, drops off, falls through the light beam of the photoelectric cell, and is then caught between the smasher plates. .

Jan 1, 1970

By Henry D. Hibbard

The finishing and casting temperature of steel is a subject concerning which there is so much to learn that some temerity is required to write about it. This paper is, therefore, suggestive rather than dogmatic, though the views expressed seem now to the writer to be correct; nevertheless, they may be modified by future developments or discoveries but until then may be of some utility, particularly to beginners in the making of steel. Consideration is limited to the temperatures of simple steels, also called carbon steels, which are those in which carbon is the only element introduced for the purpose of conferring desired physical properties. Alloy steels will receive attention later. Three things largely determine what a batch of steel really will be; via., composition, casting temperature, and rate of teeming. Each has its advocates as being the most important; but they are so interrelated that each must conform to or be right for the other two. When one is claimed to be the most essential to have right, that, probably, was the one that it was found had to be of a certain description, within narrow limits, to suit the already adopted variations of the other two; that is, it was the last of the three to be brought into line. The term "casting temperature" is rather indefinite as there ale several temperatures to which the term may be applied. Most writers who have mentioned casting temperature of steel have alluded to it in relative terms. The few who have given actual temperatures, including Langmuir, Burgess, Styri, and Bash, do not give full information about them. Their results demonstrate the efficiency of pyrometers used rather than aid the steelmaker. In order to understand and use the temperatures, one should know in each case what the steel was, the stage at which the temperature was taken, whether it was usual or not, and whether or not it was right for that steel at that stage. When these

Jan 1, 1925