Search Documents

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By W. C. Browning

The influence of the hydroxyl factor is more damaging to formations penetrated and causes greater consumption of drilling mud additives than previously realized. This hydroxyl effect on clays is essentially independent of the cations present in the drilling fluid and thus differs from the base exchange reactions that have preoccupied mud chemistry with sodium and calcium bentonite concepts for nearly two decades. The new organic polyelectrolyte-con-ditioned muds haw made it possible to use materials other than sodium hydroxide to maintain the alkalinity of such muds. The properties of silicates, as indicated by their dissociation characteristics and buffering action, are such that they can control he pH and alkalinity of drilling muds at the desired level and, at the same time, minimize undesirable hydroxyl effects associated with sodium hydroxide. This use of silicate compounds is different and distinct from prior applications of silicates as deflocculants or shale preservers. Laboratory and field data presented in this report show that silicate compositions can be utilized to adjust the alkalinity of drilling muds and, at the same time, minimize hydmxyl-promoted clay cleavage. INTRODUCTION Studies for improving the efficiency of rotary drilling techniques must consider the chemistry of drilling fluids and of the formations being penetrated. The chemical aspects of drilling must be studied in conjunction with and in relation to the mechanical factors if, for example, penetration rates are to be optimized. Drilling fluid technology has been largely influenced by chemical reactions of the montmorillonite (bentonite) clay minerals. Most of the literature of mud chemistry concerns the properties of bentonite. Clays of the kaolin or illite type, which are nonswelling, are not generally regarded as sources of drilling mud problems. If these nonswelling shale clays are considered, they are commonly regarded as inert solids. Particularly noteworthy is the fact that the relation of surface and colloid chemistry to massive shale bodies has received only scant attention from drilling technologists. Clay studies reported in the drilling mud literature have dealt, for the most part, with the properties of clays in a finely divided state, and often in very dilute suspensions. Yet frequently during drilling, shale problems not related to the rheology of clay suspensions develop in massive non-bentonitic shale sections of zero or near zero permeability. This paper is concerned with surface chemical reactions that can influence the behavior of these non-bentonite clay masses in such a manner as to adversely affect drilling operations. Browning and Perricone1,2 have pointed out that some of the most troublesome shales to drill, such as the Atoka, contain no montmorillonites. They also pointed out that mud problems can frequently be mitigated by reduction of clay cleavage achieved by using drilling fluids with a minimum of available hydroxyl ions. If pronounced clay cleavage occurs during drilling, the borehole may soften, increasing the possibility of sloughing. In addition, the resulting increased incorporation of high-surface-area clay solids into the mud system can reduce penetration rates and necessitate greater chemical treatment. This increase of shale, of colloidal or near-colloidal dimensions, into the drilling mud is due to clay aggregate cleavage and not to base exchange or swelling reactions, such as occur with bentonites. Searle and Grimshaw3 point out the difference between cleavage or slaking reactions of nonswelling clays (such as illite and kaolinite) and the swelling of bentonite. They further state that the speed of slaking is increased in alkaline water. Eitel1 cites Salmang and Becker, who recognized that clay surface reactions impart plasticity and workability to clay masses. Their results clearly show that all liquids which contain hydroxyl groups in their molecules favor the workability of clays. The ancient technique of aging clays in the moist condition to increase their "workability" is evidence that these clay cleavage phenomena are of considerable importance. The same hydration cleavage that occurs during the aging of nonswelling clays for ceramic use also acts to break up cuttings and soften the borehole during drilling operations. The mechanism of cleavage of the crystalline aggregates of illitic, kaolinitic and other nonswelling clays; and the chemical means of controlling this cleavage are therefore of considerable significance to the drilling mud chemistry. Inasmuch as there is little reference in the drilling mud literature to the cleavage reactions of nonswelling clays, the structure of these clays and certain properties that relate to the mechanism of clay cleavage will be reviewed briefly. STRUCTURE OF NONSWELLING CLAYS Clays such as kaolinite, illite and montmorillonite are compmed of alternate layers of (1) silicon-oxygen tetra-

Jan 1, 1965

By T. Federighi, S. Ceresara, C. Panseri

The results of an exploratory investigation by means of resistivity measurements at -195ºC, on the aging characteristics of a set of Al-Mg alloys with a maximum content of 7 pct Mg, are reported. Whereas for dilute alloys (Mg < 1.5 pct) only a decrease in resistivity is observed at about 100°C (due to the elimination of quenched-in vacancies), for more concentrated alloys such a decrease is preceded by an increase in resistivity in the range between -60ºand +40°C. Following some previous suggestions, this increase is considered as good evidence for clustering of solute atoms @reprecipi-tation process). From the analysis of the results it appears that, although the process is substantially similar to that observed in other Al-rich alloys, it is characterized by a strong interaction between vacancies and zones. THE process of formation of Guinier-Preston zones, i.e., preprecipitation,1&apos;2 which occurs during the aging at about room temperature in many supersaturated aluminum-rich alloys, has been extensively investigated in the past few years by several workers.2,3 owever, a very interesting question arises when the case of Al-Mg alloys is considered: although it is very easy to supersaturate Al-Mg alloys, just in the same way as for many other aluminum alloys showing preprecipitation, only very little experimental evidence was available until a short time ago in the literature supporting the existence of "natural" aging in supersaturated Al-Mg alloys (see, for example, Refs. 4 to 6). On the other hand, as is well known, the X-ray method is not useful in this case because the X-ray scattering factors of magnesium and aluminum atoms are about the same. Recently, however, Cordier and Detert7 have stressed that during the aging at about room temperature of a supersaturated Al-Mg 10 pct alloy it is possible to detect an increase in resistivity; since, as is well known, such an increase is observed also in most alloys showing preprecipitation, the above authors have interpreted their results as evidence for the formation of magnesium-rich clusters (or Guinier-Preston zones) during the aging. In the course of or ientative investigations on preprecipitation in several aluminum-rich alloys, we also could detect a similar phenomenon in more dilute Al-Mg alloys, see Instituto Sperimentale Metalli Leggeri, Annual Report, 1959, and also Ref. 8. Since the details of our observations, although of a preliminary nature, differ from those of Cordier and Detert and allow one to draw a more advanced picture of the preprecipitation process in Al-Mg alloys, we have thought it useful to report our results in this paper and to comment on them briefly.

Jan 1, 1963

By Van H. Manning

In substance, the international aspects of the petroleum industry, as these relate to the United States, are as follows: The domestic production is not keeping pace with the domestic demands; our best engineering talent warns us of the imminence of a decreased production by our oil wells, although more oil is needed; and the only practical source whence this increasing demand can be supplied for some time to come will be the foreign fields. Other nations have given thought to the future and, in recent years, have shown a tendency to adopt strong nationalistic policies regarding their petroleum resources, policies that hinder or prevent the exploitation of these resources by other nationals. In consequence, we find that, facing a probable shortage of the domestic supply, our nationals are excluded from foreign fields; and this in spite of the fact that foreign nationals have been permitted to enter into and exploit our own oil resources on an equality with American citizens and without hindrance or restrictions. This country has supplied the larger part of the petroleum consumed by the world and yet, with a failing supply imminent, it finds that those countries that, have been drawing upon our resources to supply their needs are showing a tendency to exclude us from their resources. In this way we shall be transferred from a position of dominence to one of dependence; and only by sufferance of those countries that are now seeking financial or political control of petroleum supplies, shall we be able to obtain the oil we will need. Impoetance of Petroleum Petroleum has become, during recent years, one of the essentials of our social and industrial life. All civilized countries recognize that the world is dependent on petroleum as on nothing else except textiles: foodstuffs, coal, and iron. Today, the tendency is toward an ever-increasing consumption of petroleum and its products as new and more efficient uses are found for them. The utilization of petroleum is extending more and more into the structure of our civilization. Consequently,

Jan 1, 1921

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By John R. Don

This paper, under the title of "The Genesis of Auriferous Lodes from a Chemical Point of View, Illustrated by Analyses of Samples Taken from the Chief Auriferous Area of New Zealand, Victoria and Queensland, by John R. Don, D.Sc., M.A., Lecturer on Geology in the University of Otago, N. Z.," was submitted by the author with the frank confession that its length, covering several hundred printed pages of the Transactions of the Institute, would preclude its acceptance for publication in full. But the great value of the original work which it records rendered its rejection on that ground highly undesirable ; and, after correspondence with Dr. Don, it was agreed that the Secretary should condense the paper, subject to the author&apos;s approval, omitting what was not essentially connected with the original work reported. In the discharge of this laborious and difficult duty, the Secretary&apos;s chief trouble has been his regret to cut out the acute criticisms and admirable theoretical and historical summaries of Dr. Don on the general subject of the science of ore-deposits. It should be added, that the original paper has been returned to the author, with full permission to publish it through any other medium (due mention being made of the first publication by the Institute of portions thereof), and a cordial expression of the hope that the treatise, as a whole, may be thus published, to the advantage of science. The Secretary begs to add, that many of the portions necessarily omitted from this condensed version would constitute, in his judgment, interesting and valuable separate contributions. In attempting to condense this paper, it was necessary at the outset to cut out the tint three chapters, of which the following brief outline is therefore given. Chapter I., introductory in character, indicates the importance of chemical analysis in the investigation of the genesis of ore-deposits, emphasizing the value of Prof. Posepny&apos;s Institute paper, and especially of the discussion which it aroused, and stating in general terms the theories of "lateral secretion" and "ascension." Chapter 11. describes the scope of the investigation undertaken by the author, the chief purpose of which was to determine which of the above-named theories was favored by the evidence obtained. This evidence consists chiefly (though not wholly) of analyses of the country-rock taken at various distances from the auriferous "reefs," (a) on deep mine-levels; (b) in the surface or "vadose" region : and also (c) of underlying, neighboring or connected crystallines (granite, gneiss, etc.). In addition to these investigations, there is a separate inquiry into the question of the deposition of gold in marine basins, suggested by the fact that most of the gold in the lodes of Australasia occurs in stratified deposits. Chapter 111. discusses the principles and methods followed by the author in the examination of country-rock for the purpose described. After giving his reasons for believing that careful tests of carefully-chosen samples of country-rock taken at varying distances from the ore-deposit might throw light upon the question

Jan 1, 1898

By W. R. Hicks, J. E. Pollock, E. Camp

In the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance, a substitution first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replacement with more costly material must be justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete. Test Methods Either one of two methods or a combination of both, in the absence of reliable data in similar services, may be adopted to determine to what extent replacement with other, and perhaps more expensive, materials is justified. A unit may be constructed incorporating different metals or alloys so that comparative service may be obtained under the same service conditions; this has been applied in many instances, such as condenser and tank construction, but the opportunities for inspection may be few and

Jan 1, 1935

By J. E. Pollock, W. R. Hicks, E. Camp

In the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance, a substitution first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replacement with more costly material must be justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete. Test Methods Either one of two methods or a combination of both, in the absence of reliable data in similar services, may be adopted to determine to what extent replacement with other, and perhaps more expensive, materials is justified. A unit may be constructed incorporating different metals or alloys so that comparative service may be obtained under the same service conditions; this has been applied in many instances, such as condenser and tank construction, but the opportunities for inspection may be few and

Jan 1, 1935

By A. C. Fieldner, Lester L. Hirst, Henry H. Storch

Experimental work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogehation of bituminous coal and tar by the Bergius-I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 Ib. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydro-genation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. Equipment and General Procedure of Research The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By Lester L. Hirst, Henry H. Storch, A. C. Fieldner

Experimental work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogehation of bituminous coal and tar by the Bergius-I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 Ib. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydro-genation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. Equipment and General Procedure of Research The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By Carle R. Hayward

This work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author&apos;s direction. They attempted to determine the diagram for the system Cu2S-MiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.l At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages. Preparation of Cu2S.—A piece of cathode&apos; copper from the Buffalo plant of the Calumet & Hecla Co. was cut into shavings by a shaper and converted into sulphide by heating in boiling sulphur. A porcelain casserole was used for the purpose, the heat being furnished by a Bunsen burner. It was found that after boiling in the sulphur for an hour the copper shavings were completely converted into sulphide. The liquid sulphur was then poured off, leaving the solid sulphide in the casserole in

Jan 1, 1915

By William G. [Peryam], Bishop Ottey M., Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rock-surfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to P8.00 per ton, and from the property to San Fernando the rate is P16.00 per ton. The company pays the road toll, P1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By David L. Sikarskie

The measurement of residual stress fields using X-ray diffraction techniques requires the removal of successive layers of material from the specimen. In the process of removing these layers, the underlying residual stress field is altered; hence, if the original stress field is desired, corrections must be made to the measured stresses. Although these corrections already exist for a number of cases, an alternate procedure is outlined herein whereby the corrections are presented in series form. This form is numerically more convenient within certain ranges of correction depths and in its simplicity gives additional insight into the factors affecting the corrections. It, further, readily permits determining the proper slice depth to remove and the effect on the correction of both specimen thickness and magnitude and form of the measured residual stress itself. ONE of the techniques currently being used to determine residual stress fields is X-ray diffraction. Since X-rays are diffracted essentially from the layers of atoms near the surface of the specimen, of the order of 0.0001 to 0.001 in. depending on conditions, the method can only determine stresses* in this very thin surface region. Therefore, if the residual stress field at some depth into the specimen is required it is necessary to remove successive layers of material taking measurements after each cut. In the process of removing a thin surface layer of stressed material, however, the over-all equilibrium of a cross section of the specimen is disturbed with the result that the internal residual stress which existed before the slice of material was removed is altered. This alteration of stress occurs after each slice and its effect is cumulative. Thus, if the original stress distribution is desired, corrections must be applied to the measured stresses. These corrections can be found by satisfying equilibrium on each new cross section. These corrections have been derived in detail for a number of cases, e.g., cylinders, bars, plates,&apos; and also are given in Appendix VI of Ref. 2. In each of the above cases the correction terms require the evaluation of definite integrals of the measured residual stress distribution. In general, this is indeed the way one would proceed with the corrections. There are a number of instances, however, where the integrals can be replaced by a series form of correction which is considerably more convenient numerically and, also, gives added insight into the factors which influence the corrections. Such a form of the correction is particularly useful, for example, if one is interested in designing a test such that stress corrections will be small. Also, the question of what depth of slice to use in relation to both specimen thickness and residual stress distribution itself must invariably be answered. Questions of this type can be readily answered using a series form of correction. In addition, if the correct residual stress distribution is needed only for limited depths into the specimen the series correction provides numerical results which are equivalent to the integral correction. I) DERIVATION OF THE SERIES CORRECTION The problem to be considered here is that of a bar or plate,* i.e., either one or two dimensions of the specimen is large compared with the third. Also, the residual stress distributions considered depend only on z, see Fig. 1. In view of this it can be shown&apos; that a stress correction, based on simple beam theory, satisfies all conditions of "elasticity theory" and hence is the correct (and only) solution. The integral form of the correction (this assumes that the measured residual stress is a piecewise continuous function) as given in Ref. 1 is:

Jan 1, 1968

By Paul H. Price, John P. Nolting

The history of the salt industry in West Virginia dates back nearly two hundred years; howTever, the history of salt as an important raw material for the chemical industry is much more recent. The earliest record of West Virginia salt was in 1753, when a raiding party of Shawnee Indians attacked frontier settlements in Virginia taking captive a number of the pioneers. One of these, who later escaped and returned to her friends, described how the Indians camped at a salt spring on the banks of the Kanawha River and evaporated the water to obtain a supply of salt to take back to Ohio with them. Settlement of the Kanawha Valley began in 1774, that same year the Battle of Point Pleasant ended the Indian&apos;s power in the Ohio Valley; and settlement of the Kanawha Valley progressed rapidly with a consequent increase in the importance of the Kanawha Licks as a source of salt. In those days the evaporation of the brine was a family matter for which the family wash-kettle was commandeered. In 1797, Elisha Brooks erected the first salt furnace in the Kanawha Valley. It consisted of two dozen small kettles set in a double row, with a flue beneath, a chimney at one end, and a fire bed at the other. He obtained his brine at a depth of 20 to 30 ft by sinking hollow logs, called "gums" into the salt lick and dipping the brine with a bucket. His production was about 150 lb a day and sold for 8 to 10 cents a pound. In 1806, the Ruffner brothers, David and Joseph, prospected for and drilled the first well in America using a spring pole and steel chisel bit. After several failures they succeeded, in 1808, in drilling to a total depth of 59 ft where they secured a good flow of strong brine. Most standard drilling tools, jars, casing, and practically all the basic oil well drilling machinery now in use, were developed in the drilling of salt wells. To evaporate this brine, the brothers built a wood-burning furnace similar to that of Brooks but with a better arrangement and with more and larger kettles. When production was started they reduced the price of salt to 4 cents a pound. By 1817, there were some 30 salt furnaces in the Kanawha area. It was in this year that bituminous coal first was used as an industrial fuel. David Ruffner again pioneered the way by converting his furnace for the consumption of coal. This year also brought about the formation of the first trust which controlled production and set a price of 1 cent a pound for the salt.

Jan 1, 1950

By I. Fatt

A recently developed system for measuring electrical resistivity of liquids without use of electrodes offers some interesting possibilities in electric logging technology. The equipment as supplied by the manufacturer is satisfactory for continuous mud logging on a drilling rig or for measuring mud or filtrate resistivity in the laboratory. A simple modification of the commercially available instrument makes it suitable for measuring resistivity of core samples in the laboratory. The continuous measurement of mud resistivity on a drilling rig is a convenient means for detecting mixing of formation water with the drilling mud. Such information is useful to the geologist, the mud engineer and the logging engineer. However, continuous mud resistivity logging by conventional electrode-type resistivity cells is beset with difficulties. The mud, sand and rock chips abrade the electrodes, thereby changing the cell constant and eventually destroying the cell. Also, additives and crude oil in the mud may poison the electrodes by coating them with a nonconductive material. An electrode-type resistivity cell. therefore, may give erroneous readings under certain conditions. Electric logging companies circumvent the electrode poisoning problem by using a four-electrode resistivity cell for measurement of mud resistivity. In this cell, change in electrode area does not change the cell constant. However, the four-electrode cell is difficult to adapt for continuous reading and does not solve completely the problem of electrode abrasion by the sand and cuttings in the mud. The measurement of electric logging parameters on core samples in the laboratory encounters some of the same problems discussed in connection with mud logging. Ideally, the electrical resistivity of a core sample should be measured by placing platinum black electrodes in direct contact with the plane ends of a cylindrical or rectangular sample. Platinum black electrodes however, are much too fragile and easily abraded to be brought in contact with a rock sample. Also, oil or other constituents in the fluid contained in the sample will poison platinum black. In practice, gold-plated brass electrodes, in an AC bridge circuit operating at about 1,000 cps, are used for routine core analysis. For more precise work in research studies, a four-electrode scheme is used.&apos;,&apos; Preparation of the samples for the four-electrode method is much too involved for routine core analysis. An apparatus for measuring resistivity of liquids without use of electrodes was described by Guthrie and Boys3 in 1879. They suspended a beaker, containing the electrolyte, by a torsion wire and rotated a set of permanent bar magnets around the vessel. The eddy currents induced in the electrolyte reacted against the rotating magnetic field to develop a torque, which was measured as a deflection of the torsion wire. In 1879 this method could not be made precise or convenient because of the lack of strong permanent magnets. The writer described a very greatly improved apparatus similar to that of Guthrie and Boys, but it was not suitable for continuous measurements or core samples.&apos; Many electrodeless resistivity devices using radio frequency current are described in the literature.5, 6 These generally are suitable only for noting the end-point in a chemical titration. They do not measure resistivity, instead measuring a complex quantity which includes the dielectric constant and the magnetic permeability. The first description of the apparatus to be discussed in this paper was given by Relis.7 Improvements and modifications are described by Fielden,s Gupta and Hills,> and Eichholz and Bettens.10 DESCRIPTION OF APPARATUS The apparatus used in this study is based on the principle that the solution under measurement can form a loop coupling two transformer coils, as shown in Fig. 1. For a fixed AC voltage applied across Coil A, the voltage appearing across Coil B is a function of the resistance of the liquid-filled loop. The details of the voltage generating and measuring circuits are given in Refs. 7, 8, 9 and 10. A block diagram of the equipment is given in Fig. 7. Special features worth mentioning are the operating frequency of 18,000 cps and the automatic temperature compensation which results in the given resistivity readings being automatically correlated to 25°C. The liquid loop supplied by the manufacturer, shown in Figs. 1 and 2, was modified for use in core analysis (Fig. 3). The core sample under test is substituted for a section of the original loop. As shown in Fig. 3, the unit accepts only plastic-mounted cylindrical core specimens. A Hassler-type sleeve easily can be designed for the unit if unmounted cores are to be measured. EXPERIMENTAL PROCEDURE MUD LOGGING A simulated mud line was set up in the laboratory.

By George D. Roberts

INTRODUCTION CIVIL engineers are primarily interested in maximum core recovery. This is even more important in foundation work than in mining investigations where sludge samples are of some value. The soft materials, such as clay, gouge, or partially decomposed seams that are most readily ground up or washed away, are the materials that usually have the greatest influence on foundation and leakage conditions. Undisturbed samples of such materials should be obtained for detailed geological examination and laboratory tests. Therefore the attainable goal of sampling in connection with foundation investigations is the recovery of 99.9 pct of undisturbed core. FACTORS CAUSING CORE LOSSES The principal factors contributing to core losses are: (I) coring badly fractured or very soft material; (2) use of improperly designed coring equipment, including the use of bits of too small a diameter; (3) lack of the proper training and attitude on the part of the drillers and pertinent technical information on the part of the supervising personnel. Little can be done about the character of the material being cored but the other two factors contributing to unsatisfactory performance can be corrected. Although the title of this paper is the improvement and standardization of core barrels, it is believed that the drillers&apos; shortcomings and the lack of pertinent technical literature are more detrimental to good core recovery than either of the other factors. USES FOR LARGE DIAMETER CORE BARRELS It is well known that the use of larger diameter bits and core barrels generally produce better cores, particularly when sampling soft or broken material. The use of larger and larger bit diameters and the insistence on better core recovery is well demonstrated by the change in practices of the various districts of the Corps of Engineers. Today NX core is the smallest diameter commonly permitted for investigational work and the more active districts are using coring bits up to 6 in. in diameter, as well as 36 and 40-in. calyx rigs. The latter size has proved to be just as economical because it provides more room for core removal and cleanup operations. The use of large diameter cores to replace the driving and jacking methods of obtaining soil samples is also increasing. The 5 7/8-in. Denison sampler, developed by H. L. Johnson to obtain samples from soft formations, is one example. The principal uses for bits larger than NX are: sampling soils and semi-consolidated rock; sampling decomposed rock or rock with soft seams; sampling concrete; obtaining samples for laboratory tests; drilling drainage holes, and other miscellaneous work. CORE DRILLING PRACTICES OF SEVERAL ENGINEER DISTRICTS Little Rock District The writer was employed in the Little Rock District from 1938 until 1942. Prior

Jan 1, 1947

By John W. Chandler

INTRODUCTION Where and how to spend the exploration dollar to net the greatest economic return, has always been a major problem for mining companies. Minerals are being consumed in ever increasing quantitie: throughout the world and the mining industry is being called on to meet this demand. In view of the present world-wide nationalistic trend, it is becoming more difficult to determine where exploration money can be spent most profitably. An exploration project should be evaluated continually--in the beginning, to define economic targets and later to determine, as early as possible, whether a project has a chance of developing into a venture that will make a profit acceptable to top management. At this point, a decision can be made whether or not to proceed with plans to bring in a new mine. Exploration, evaluation, and development, therefore, must be fully integrated in transforming an exploration project into a profitable mining venture. DEMAND FOR LEAD AND ZINC Lead and zinc are metals basic to our economy and the demand for them will continue to rise as the population in the world increases. If the population continues to grow at the present rate, it will about double by the year 2000. The accelerating demand for these metals is shown by statistics. Nearly half as much lead (48%) and more than half as much zinc (55%) have been mined between the two world wars as in all pre- ceding history. (1)

Jan 1, 1970

By H. D. Hoskold

DuRing the last few years, various persons have been put forward as originators of some mechanical device for the purpose of finding distances without the use of a chain or other linear measuring-instrument, and among these, the Englishman, Gascoigne, 1639, is prominent as the first in England; while James Watt, 1771, and William Green, 1778, are also included in the list of inventors. It is possible that this useful and important problem occupied the attention of others prior to the date cited, and, consequently, it is difficult to decide what nation first gave birth to the inventor of an instrument for the object under consideration. A very important work appeared, not long since, in Paris, devoted to a history and discussion of some of the older and newest forms of surveying-instruments,* and at page 79 of that work a curious old instrument is exhibited, called Bigonometre, i. e., an instrument for finding distances and solving trigonometrical problems. in surveying. A copy of the diagram of the instrument exhibited in the book referred to is represented in Fig. 1. Having had an occasion to read the French work referred to, I communicated with the author of it, and he was good enough to reply that he found a diagram of this old instrument in a book published in 1597, by Danfrie, existing in the library of the Academy of Sciences, in Paris. Col. Laus-

Jan 1, 1904

By F.S. Norcross

Manganese has long been considered one of the United States&apos; most important strategic raw materials. Its indispensabil-ity in steel manufacture makes it vital to the nation&apos;s industrial life. Coupled with this indispensability is the fact that domestic producers have not been able as yet to supply more than a small part of the nation&apos;s manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is consumed in the form of ferromanganese, an alloy that averages 80 per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevailing prices. Dependence upon foreign sources thrust the United States into serious difficulties during the World War. At the start of hostilities in 1914, the nation was obtaining about four-fifths of its ore from the Eastern Hemisphere. Domestic production had been negligible, amounting to only 3000 to 7000 tons a year. As the war continued, shipments from the East, endangered by sea attack and blockade, dwindled rapidly. Imports from Brazil mounted. In this grave emergency, the United States, starting almost from scratch and under the stimulus of high prices, succeeded by 1918 in producing a peak of 3II,000 tons, about 35 per cent of its consumption that year. Since the war, the United States has depended upon foreign sources for more than nine-tenths of its high-grade ore. During 1936, 1937 and 1938, imports for consumption averaged 736,000 tons a year. During the same period, domestic shipments averaged 21,000 tons a year. Of the imports, the U.S.S.R. accounted for an annual average of 280,000 tons, the Gold Coast 208,000 tons, India 74,000 tons, and Brazil 72,500 tons. But India and Brazil, which in 1936 ranked third and fourth in the list of importers, were displaced in 1937 and 1938 by a new and much nearer source—Cuba. From less than I per cent of United States imports in 1931, the island republic increased its shipments to more than 27 per cent in 1938. Cuba&apos;s average for this three-year period was 97,000 tons, and its total for 1938 was 131,000 tons. History The story of the economic development of manganese in Cuba dates back to the Spanish-American War days. John Green-way, then one of Theodore Roosevelt&apos;s

Jan 1, 1943