Search Documents

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall's work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann's approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen's approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

INTRODUCTION The first installation of large, commercial, high gradient-high field cannister and matrix magnetic separators for removal of impurities from kaolin was made in 1973 (1). Since then the technology and equipment have been widely adopted for clay processing with about 12 units in commercial use. These new separators have filled a need, caught the imagination of many and become a technology worth fighting for. A fight has occurred, and a resolution on royalties for kaolin processing, at least, has been achieved. LIMITATIONS TO APPLICATIONS OF MAGNETIC SEPARATORS Other than the use of these magnets on kaolin clay, no other application has yet achieved widespread adoption. Dr. Iannicelli blames inertia, and1 would agree that it is a factor. There are other reasons too, and if they are examined, they may isolate problems that R&D can significantly assist in solving. I'd like to break the problems into two areas. Machine limitations - the mineral properties are there but performance is insufficient or uneconomic. Separation limitations - the mineral properties aren’t there, but the magnetic separation would perform well if the properties were there (size is right; concentration is right, etc).

Jan 1, 1979

By D. O. Wyble

Five water-driver fields, for which pressure predictions had been made within a few years after discovery, were re-studied when four to five years of additional pressure and production data became available. It was fortnd that forecasts of the pressure in water-dri~fe reservoirs may be subject to considerable unccrtainty. Predictions car be erroneous when there is insufficient presswe history to define the cllaracteristics of the aquifer, and when there are errors in the pressure, production or geologic data. INTRODUCTION The efficient operation of an oil or gas reservoir requires that the important characteristics of the reservoir be determined soon after its discovery. It is especially desirable to evaluate the pressure-production relationship quickly, for this relationship provides a basis for deducing the type of production mechanism that is operative, and for making pressure predictions. The pressure predictions, in turn, provide a basis for calculating efficient rates of production, determining whether water or gas should be injected, etc. The importance of pressure prediction is such that forecasts should be made as accurate as possible, and the limits of error well defined. Historically, pressure forecasts for some fields have proved very accurate, while for others the forecasts were so erroneous that they resulted in the adoption of wrong, or at best, unnecessary production practices. Pressure predictions made for water-drive fields are especially subject to error. Accurate forecasting for these fields requires that much be known not only about the reservoir proper but about the adjacent water-filled rock as well. The water-containing rock, or aquifer, may extend for many miles, and often there is only meager data regarding its thickness, permeability and porosity. Much of the information must be inferred from the previous pressure behavior of the reservoir. A brief pressure history may provide little information about the characteristics of the aquifer. Hence, pressure predictions made early in the life of water-drive fields can be incorrect. The work described in this paper was done to determine the degree of reliability which can be expected of pressure predictions made within a few years after water-drive fields are discovered. Five fields, for which the original pressure predictions had been based on less than seven years' history, were re-examined with the aid of four to five years of additional pressure data. Where the predictions were inaccurate, the reasons for failure were ascertained. The studies were accomplished by use of the electric reservoir analyzer.' The analyzer was first adjusted to repeat the original pressure-production match using the same values for the various parameters as were used in the original study. Then, the actual production rates experienced during the time elapsed since the initial study were set into the analyzer, and the pressure behavior indicated by the machine for this period was compared with that which actually OCcurred. Where the pressure profile traced out by the analyzer deviated from the observed field behavior, the analyzer was readjusted to obtain a better over-all match. The old and the new solutions were compared to determine the reasons for any differences. COMPARISON OF PREDICTED RESERVOIR PRESSURE BEHAVIOR WITH ACTUAL PERFORMANCE Field A The original pressure-production match is entirely adequate as evidenced by the pressure match of the field's history subsequent to Jan., 1952 (see Fig. 1)'.

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By W. O. Philbrook, A. H. Jolly, T. R. Henry

In the course of a study of slag-control methods, the authors devised a laboratory technique by which the basicity of basic open-hearth furnace slags could be estimated with sufficient accuracy to make the method of possible interest for slag-control purposes. The process consisted of measuring the slight basicity of an extract of the powdered slag in water. The procedure was presented, for the benefit of those who might care to experiment with it, in a paper submitted in the 1944 McKune Award Contest and presented at the 1944 Open-hearth Conference in Pittsburgh.' Interest expressed at that meeting and favorable operating experience with the method at a neighboring plant, as described in a related paper by Michael Tenenbaum and C. C. Brown,; have encouraged us to present further details of the development, technique, and pitfalls of the method and some additional data not included in our first report. At the outset it must be admitted that this method of estimation of slag basicity is not perfect; neither is any other that we know of. It is subject to somewhat greater errors than would be desirable, but compares favorably with other techniques in this respect. It has the disadvantage that it places the final determination of slag basicity in the hands of a laboratory technician rather than the furnace oper- ator, although it can be operated in a control laboratory adjacent to the furnaces. It requires close attention to certain details, as do most laboratory procedures. On the favorable side, it eliminates the "human factor" of personal judgment inherent in estimation from pancakes or powdered samples. The procedure can be placed in practice much more rapidly and presents much less of a training problem than visual methods of estimation. The principle and operation of the method are so simple that it would not be surprising if others have experimented with the same or similar procedures, but we are not aware of any prior publication of details. Our own shop has been operating fairly successfully for several years with the aid of slag pancakes. Since the past year or two have not been favorable for the expenditure of time and energy where the need was not urgent, we have not introduced the new practice for actual slag control and hence do not have extensive operating data. In presenting this method, therefore, we make no claims as to theoretical justification nor guarantees as to practical applicability, but offer it as an empirical observation. We believe it has sufficient merit to warrant its investigation by those just instituting a slag-control program or in search of supplementary methods for judging slag basicity Principle of the Method It is well known that when burnt lime or slaked lime is shaken up with water it

Jan 1, 1945

By Newell G. Alford

With the workable area of coal prospected and known as to workability and quantity and sampled and tested for desired quality comes the determination of the projection and method of working. The best method will be the one supplying the greatest degree of safety, the most merchantable product, the minimum average cost per ton with the largest yield of recoverable coal. Based on coal elevations, taken at the bottom of the seam on all known outcrop exposures, prospect openings or drill holes, coal contours are made on the map to be used in developing the mining plan. The contour interval should be as close as available information will permit. For general utility in layout of mining, haulage, drainage and ventilation, a map scale of 400 ft. per in. is preferable. In mountainous sections, location of the main out- crop opening or hoisting shaft is often limited by the available railroad route and amount of land level enough for a plant site. In level country, where a tipple and hoisting shaft may be placed at will, choice of the plant site should depend on the minimum average underground haul for the total coal to be worked to the new

Jan 1, 1932

By C. F. Gates, H. J. Ramey

Recent literature shows that pronounced increases in oil recovery can result from the use of miscible systems in recovery operations. This literature also points out certain problems associated with maintaining miscibility, e.g., compositional changes resulting from alterations in pressure and temperature or from zone dilution. The purpose of the work described in this paper was to study miscible zones for possible use in waterflooding operations and examine the manner in which these zones break down. The fluid system selected for study was oil—terNary-butyl alcohol—water, which, because of its narrow range of miscibility, is ideally suited for investigation in short, linear systems. The laboratory-observed effects on oil recovery and zone stability of a number of variables are reported. Among the variables investigated were miscible zone size, viscosity ratio, length of travel, and interstitial water saturation. Results obtained with this system show that interstitial water adversely affects recoveries because of premature phase break. Salinity of the water further aggravates Ais situation. This effect, although pronounced for this system, would probably occur in any fluid system containing an alcohol. As expected, viscosity ratio has a decided influence on recovery efficiency and zone stability. The results also show that use of a suficieno zone size, even though the system has poor phase characteristics, yields higher oil recoveries than are obtained from straight water floods. Length-of-travel studies showed a square root relationship between zone growth and path length for favorable viscosity ratios. No such clear-cut dependence was observed under unfavorable viscosity conditions. INTRODUCTION As new oil reserves have become increasingly more difficult and expensive to find and develop, the oil industry has devoted more and more time and money to finding more efficient methods for exploiting known reserves. The increasing number of water floods is one manifestation of this attempt to improve oil recoveries from existing fields. Since considerable quantities of oil are by-passed by the waterflood process, it is only a partial answer to the problem. The search continues. Of late, several proposed processes have received the critical attention of investigators. Among them are gas drives, in situ thermal reactions and miscible displacements. The present paper is concerned with miscible displacements in conjunction with water floods. Recent literature1- reports that, under proper conditions, oil recoveries from LPG floods, propane sweeps, condensing gas drives, etc., approach 100 per cent of the oil in place in the region contacted by the flood. This literature also points out some of the problems associated with these processes, one of the main ones being the maintaining of miscibility. Compositional changes resulting from pressure and temperature variations or from zone dilution give rise to phase breaks and loss of miscibility, the conclusion being that, after loss of miscibility, much of the beneficial influence of the zone is lost.' The results of the subject work show that, if sufficient zone material exists ahead of a phase interface, considerable improvement in oil recovery can be obtained. In order to increase our understanding of the behavior of miscible systems as they degenerate into immiscible processes, a laboratory system having rapid deterioration characteristics was needed. The fluid system oil—ter tiary-butyl alcohol (TBA)—water possesses these properties and was the system investigated. Although these fluids are different from those generally employed in miscible studies, an understanding of their behavior can be applied to other miscible slug processes. However, under conditions where mass transfer maintains a miscible system through multiple contacts, e.g., enriched gas drive or high pressure gas drive, the observed behavior of alcohol zones would not be applicable. The variables of interest were zone size, viscosity ratio, length of travel, initial water saturation, rate and core characteristics. Of these, only the effects of the following on zone breakdown and oil recovery are reported in detail: (1) zone size, (2) path length, and (3) initial water saturation. The effects of viscosity ratio and core characteristics are discussed in conjunction with other variables. Although initial water saturation is not envisioned as important to the phase behavior of hydrocarbon systems, e.g., LPG, it is important in alcohol systems. The properties of the fluids and cores used are given in Table 1. As previously stated, this fluid system was selected because of the limited range of miscibility

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951

By Freeman Bishop

This year the metal mining industry is in for some difficult decisions as the nation struggles to control inflationary pressures resulting from higher production costs and a money-squeeze policy. Re- clouding these problems will be campaign oratory as Congress seeks reelection. Charges will be hurled back and forth between a Republican White House and a Democratic Congress. Inflation and Vietnam will be the big one. Hut pollution i. coming on strong. President Nixon has formed a new Council on Environmental Quality although he already had named a similar unit within his Cabinet six months ago. Both are charged with bringing 1.0 bear all of the Federal Government&apos;s talents on the focal points of antipollution measures The biggest task will be to find out how many different "units" are currently mixed up in these efforts.

Jan 1, 1970

By S. Usui, I. Iwasaki

The effect of pH on the adsorption of dodecylamine at the mercury-aqueous solution interface was investigated by differential capacity and electrocapillary measurements. With dodecylammonium acetate, the differential capacity curves showed two desorption peaks in the cathodic branch with their relative intensities varying with the solution pH. With dodecyltrimethylammonium chloride, only one cathodic de-sorption peak was observed in the same pH range. Through thermodynamic analysis of the electrocapillary curves, the adsorption density of undissociated amine was evaluated separately from that of aminium ion. The adsorption densities of the un-dissociated amine and of the total amine increased with increasing pH. The ratio at the interface of undissociated amine to aminium ion was several orders of magnitude greater than the ratio in the solution and increased with increasing pH. The potential at the closest distance of approach of counter ions to the mercury surface was compared with values of zeta potential on quartz previously reported. The most important variable in the flotation separation of minerals is probably the pH of the pulp, and a number of theories have been proposed to explain its effect on the condition of the mineral surfaces, on the dissociation of collectors and of inorganic and organic species (accidentally present or intentionally added) in the pulp, and on the mineral-collector interaction. In the development of a theoretical background for oxide flotation systems, an experimental approach based on electrokinetic measurements has been of much value, although the effect of pH becomes confounded since it governs both the electrochemical conditions of the oxide surface and the dissociation of the collector. For investigation of the adsorption behavior of long-chain collectors on oxide minerals, however, electrokinetic potential measurements are the most widely used technique. Hydrogen and hydroxyl ions are found to be the potential determining species, thereby governing the interfacial electrical conditions. The electrostatic interaction between the charged mineral surfaces and ionized collectors is regarded as the driving force for the adsorption of the collectors. An association of alkylamine collectors adsorbed on quartz surfaces has been postulated from streaming potential measurements, and a term "hemi-micelles" has been proposed.&apos; The possibilities of coad-sorption of undissociated amine along with aminium ion has been inferred from contact angle measurements? and from adsorption studies.~ Electrochemical titration as applied to silver sulfide provides a more quantitative approach to the analysis of the electrical double layer at an ionic solid-solution interfaceqG and the electrochemical evidence for the adsorption of amine at pH 4.7 indicates a specific affinity of dodecylammonium ion towards silver sulfide surfaces, whereas at pH 9.2 the adsorbed species might be free arnine." A combination of differential capacity and electrocapillary measurements on a dropping mercury electrode was reported to be a sensitive method of provid- ing reliable information on the adsorption behavior of dodecylammonium acetate (DAA) at a natural (near neutral) pH.? It was also shown that there were striking similarities in the properties of the double layer and in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide. The effect of pH on the differential capacity curves at a mercury-sodium fluoride solution interface has been investigated by Austin and Parsonss who reported that between pH 7 and pH 11 there was very little effect. In the present paper, the adsorption behavior of DAA was investigated as a function of pH through differential capacity and electrocapillary measurements and the information gathered was correlated with that available in literature on quartz and silver sulfide. Experimental The apparatus and the method used for determining the differential capacity and the electrocapillary curves were identical to those described previously.&apos; The ionic strength of the supporting electrolyte was fixed at 0.1 M with potassium fluoride, and the pH of the solution with potassium hydroxide. Only the neutral to alkaline range was covered in order to avoid the dissolution of the glass vessel with hydrofluoric acid. Results In Fig. 1 the differential capacity has been plotted against the applied potential at a DAA concentration of 10-&apos; M at three different pH values. The curves are characterized by one capacity peak in the anodic branch, by two capacity peaks in the cathodic branch, and by a marked depression in capacity between the peaks. The depression indicates an adsorption of the arnine in this potential range. One of the cathodic peaks appears at pH 7.3 near -1.4 v and decreases with increasing pH. The other appears at pH 8.9 near —1.2 v and increases with increasing pH. At pH 9.6 only the latter peak is observed. Beyond the cathodic peaks, all the curves tend to converge with the curve in the absence of DAA, implying that two different species are being desorbed in this potential region. The anodic peak near 0.0 v increases markedly with increasing pH. The well-defined anodic peaks at pH 8.9 and 9.6 were accompanied by an appreciable increase in the current flow (in excess of O.luA), and, therefore, is a "pseudo-capacity"&apos;" due to a

Jan 1, 1971

By B. E. Eakin, R. T. Ellington

An apparatus and a procedure for determining the viscosity behavior of hydrocarbons at pressures up to 10,000 psia and temperatures between 77 and 400° F are described. The equipment is suitable for measuring viscosity of either the liquid or vapor phases or the fluid above the two-phase envelope for systems exhihiting retrograde phenomena, according no the phase state of the system within these ranges of temperature and pressure. Equations are developed for calculation of viscosity from the experimental measurements, and new data for the viscosities of ethane and propane at 77° F are reported. INTRODUCTION With the advent of higher pressures and temperatures in industrial processes and deep petroleum and natural gas reservoirs, demand has increased for accurate values of physical properties of hydrocarbons under these conditions. Proportionately, more frequent occurrence of natural gas and condensate-type fluids is encountered as fluid hydrocarbons are discovered at greater depths. This increases the importance, to the reservoir engineer, of being able to predict accurately the physical properties of light hydrocarbon systems in the dense-gas and light-liquid phase states. Reliable gas viscosity data are limited primarily to measurements made on pure components near ambient temperature and at low pressures. Few investigations have been reported for high pressures, and except for methane, data on light hydrocarbons are subject to question. This is demonstrated by the large discrepancy between sets of data on the same component reported by different investigators. For mixtures in the dense gas and light liquid regions and for fluids exhibiting retrograde behavior there are very few published experimental data. Viscosity data for methane have been reported by Bicher and Katz,1 Sage and Lacey,12 Comings, et al,3 Golubev,3 and Carr,3 with good agreement among the last three sets of data. Comings, Golubev and Carr utilized capillary tube instruments for which the theory of fluid flow is well established. The theory permits calculation of the viscosity directly from the experi- mental data and dimensions of the instrument alone. Sage and Lacey, and Bicher and Katz used rolling-ball viscometers. The theory of the rolling-ball viscometer has not been completely established, and these instruments presently require calibration by use of fluids of known viscosity behavior before viscosities of test fluids can be measured. To obtain accurate data it is necessary that the rolling-ball viscometers be calibrated by use of fluids of density and viscosity similar to the test fluids, a difficult selection for the gas phase. From the methane data and experimental tests on various natural gases, Carr developed a correlation for predicting the PVT behavior of light natural gases.2,3,4 This correlation was based on data for a very limited composition range; its application to rich gases and condensate fluids is questionable. The object of this investigation is to develop an instrument which can be used to obtain viscosity data at reservoir temperatures and pressures, for rich gases, condensate-type systems above the two-phase envelope and light liquid mixtures. These data will be used in an effort to develop correlations to represent the viscosity behavior of these fluids. APPARATUS In a previous viscosity study Carr2 utilized a modified Rankine capillary viscometer configuration," Fig. 1. In this instrument the gas to be tested is forced through the capillary tube in laminar flow by motion of a mercury pellet in the fall tube, the measured displacement time being that required for the mercury slug to move between the brass timer rings. The viscometer is constructed of glass and mounted in a steel pressure vessel. The test gas pressure in the viscometer is balanced by an inert gas (usually nitrogen) in the vessel. Excellent results have been obtained with instruments of this type, with Carr2 and Comings5 reporting repro-ducibilities of 99.5 to 99.3 per cent and an estimated absolute accuracy of 99 per cent. However, these instruments have limitations which have precluded their use for liquids. The need for maintaining a balance between pressures of the test fluid and inert gas in the viscometer vessel presents operating problems, and requires charging the test fluid to the viscometer very slowly. The principle drawback to the Rankine unit is behavior of the mercury slug which provides the pressure differential across the capillary. When even trace quantities of propane or heavier hydrocarbons are present in the test gas, the mercury tends to subdivide

By R. G. Ward, John Henderson. R. G. Hudson, G. Derge

Densities of melts of the iron oxide-silica system in contact with solid iron have been measured by the maximum hubble pressure method in the composition range O to 37 wt pct SiOz and the temperature range 1255 to 1410C. The constitution of the melts is discussed and it is postulated that the structure changes from a dislribution of iron ions in an oxygen ion network at pure "FeO" to a distribution. of iron ions in a network of silicate tetrahedra at the orthosilicate composition. JOHN HENDERSON, Junior Member AIME, was formerly with the Metals Research Loborotory, Carnegie Institute of Technology, Pittsburgh, Pa., on leave from Broken Hill Proprietary Co., Ltd., Research Division, Shortland, Australia. R. G. HUDSON, formerly with Metals Research Laboratory, is now with the John Jay Hopkins Loborotory for Pure and Applied Science, General Atomic Division, General Dynamics Corp., LaJolla, Calif. R. G. WARD, was formerly with the Department of Metal lurgical Engineering, Carnegie lnstitute of Technology, while on leave from the Department of Metallurgy, University of Sheffield, England. G. DERGE, Member AIME, is Jones and Laughlin Professor of Metallurgical Engineering, Carnegie lnstitute of Technology. Manuscript submitted January 19, 1961. ISD The system iron oxide-silica is an important one metallurgically because it forms the basis of several complex slag systems in use for industrial smelting and refining processes. In recent years considerable work has been done on liquids of this system but there are still many points of difference among workers using different experimental techniques and theoretical approaches. Phase equilibria/"3 activity,4-6 electrical conductivity,&apos; current efficiency,&apos; transference number,8 viscosity,9 surface tension,&apos;&apos; and density" measurements have all contributed to an understanding of the problem. Measurement of density is one procedure which is directly indicative of liquid structure since any deviation from ideality must be a result of structural interactions. Liquids of the iron oxide-silica system are of special interest because this is one of the few metal oxide-silica systems on which measurements can be carried out conveniently over the entire composition range from pure oxide to silica saturation. This includes the range of high basicity which has received relatively little attention in other systems. Although one investigation of density in this system has previously been undertaken," the results seem of sufficient importance to warrant the independent redeter-mination reported here.

Jan 1, 1962

By A. U. Seybolt, R. A. Oriani

The pressure and composition of the solid solution of nitrogen in chromium has been investigated as a function of temperature. The partial molal heat of solution, the activity of nitrogen in solid solution, and the partial molal free energy have been computed. The enthalpy of three reactions is summarized: N + 2Cr(3) = Cr2N(4), H° = —28,500 cal per mol 1/2N2(p) + 2Cr(8) = Cr2N(3)1 ?HO = —23,500 cal per mol 1/2N2(p) = N, ?H° = 5,000 cal per mol. WORKERS who have investigated the problem of the preparation of ductile chromium have been concerned with the effects of minor amounts of impurities upon this refractory metal. In particular, gaseous impurities such as oxygen and nitrogen have been suspected of causing trouble because of many known cases where brittleness in transition elements has been definitely traced to these elements. In order to evaluate the possible effects of the nitrogen impurity in chromium, it appeared desirable to learn something of the dependence of the nitrogen solubility upon temperature and pressure. Previous Work Maier3 in 1942 in his treatise on sponge chromium reviewed the thermodynamics of the chromium nitrides Cr2N and CrN, both of which are well-estab- lished compounds, but which apparently have not been studied in much detail. Maier presented some free energy-temperature expressions for the reactions 2 Cr,N = 4 Cr + N2 [1] and 4 CrN = 2Cr2N + N2 PI based mainly on the work of Satoh2 and Sano." Pearson and Ende3 in 1953 briefly reviewed the thermodynamics of Cr-N using the same data available to Maier, and also derived a free energy-temperature expression for reaction 1. Of the two nitrides mentioned previously, the present investigation was only concerned with Cr,N, since this nitride is in equilibrium with the metal phase, at least over most of the temperature range, Blix4 in 1929 established the structure of Cr2N (close-packed-hexagonal) by X-ray diffraction methods, and indicated that its homogeneity limits extend from 11.2 pet to 15.1 wt pet N. At a temperature of 1200°C, 38 mm Hg from the Maier expression and 43 mm Hg from the Pearson

Jan 1, 1957

By J. E. Pavlick, A. G. Guy

The total creep of tin alloys containing antimony in solid solution was observed to decrease with increase in antimony content. However, near the solubility limit an anomalous maximum in deformation was. found, in agreement with similiar observations by Bochvar. IT has long been recognized that alloys may deform more rapidly under stress if there is a tendency for a phase change or other structural change to occur simultaneously. However, the phenomena involved are complex and in some instances the opposite effect, strengthening, may result.&apos; This area of research has not attracted much interest in the western world, and although Russian investigators have studied it for the past 15 years their work has not received due attention here. Recently diametrically opposing views on one aspect of this problem have been espoused by two Russian investigators, Kornilov and Bochvar. The question is this: in certain binary alloys tested in creep at the temperature where the solute is at the limit of solid solubility, does the incipient formation of the second phase strengthen or weaken the alloy? Korni-lov&apos;s arguments in favor of strengthening were presented at the 1954 Symposium at the National Physical Laboratory, =Creep and Fracture of Metals at High Temperatures.The most recent statement of Boch-var&apos;s theory of weakening is in Oding&apos;s new book on creep and rupture.3 Although Bochvar agrees that strengthening occurs in some alloy systems, he argues that in certain alloys an anomalous weakening is observed. However, the extensive work of Korni-lov&apos;s group on creep properties of alloy systems has not revealed any anomaly of this type, but instead has tended to refute Bochvar&apos;s theory. This clear-cut controversy offered a good opportunity for a simple experiment to resolve the problem. The experiment and its results supporting Bochvar are the subject of this paper. However, it will be helpful first to sketch the present status of the larger question of the effect of a phase change or other structural change on plastic deformation. PREVIOUS WORK One of the first researches in this area was by Pfei1,37 who investigated the creep resistance of an 80 Ni-20 Cr alloy containing varying amounts of titanium. He found that the resistance to creep increased rapidly as the solid solubility limit in the alloy at 775&apos;c was approached and slightly exceeded. With further addition of titanium the creep resistance decreased, presumably because of precipitation effects. Bochvar&apos;s first work in this field was a study in 1945 of "superplasticity" in zinc alloys containing 15 to 25 pct Al.4 He found that alloys quenched from about 400 had anomalously low hardness when tested below this temperature. The following year, in a paper on the dependence of mechanical properties on the composition and structure of alloys,5 he extended some observations of Kurnakov to predict that at high temperatures of testing the hardness values for solid-solution alloys might be lower than those for the component metals. He also pointed out the influence of changes in solidus temperature in affecting curves of hardness vs composition, and he

Jan 1, 1962

By R. J. Sullivan

DURING the past twelve months the Loudon pool of the Eastern Interior Coal Basin has become established as one of the two largest discoveries since the revival of exploitation in the Illinois region and now occupies a position among the important pools of the United States. On Aug. 1, 1939, production averaged 54,000 bbl. per day from 990 wells, having accumulated a total of 10,305,000 bbl. Its very active develop-ment promises to continue for fully another year. It is the site of one of the industry&apos;s most singular large-scale gas-injection programs. LOCATION AND RESERVOIR CHARACTERISTICS At present the pool embraces an area 15 miles long by 3 ½ miles wide in eastern Fayette County, along the western rim of the now well-known Illinois Basin&apos;s deeper part, through townships 6, 7 and 8 north and ranges 2 and 3 east of the Third Meridian. It is the northernmost, and most prominent, productive structure of a group extending over a 50-mile trend southward to the Dix pool of Jefferson County. Three horizons have been proved to carry production-namely, the Weiler sandstone at 1390 ft., the Paint Creek sand at 1460 ft. and the Benoist or Bethel, at 1500 ft. Geologically, they fall in the Chester series of the upper Mississippian system, where much of Illinois&apos; early-day oil was found, having been laid down in shallow off-shore waters as a part of the vast delta deposit underlying central Illinois and parts of Indiana and Kentucky. As a result of this type of sedimentation, followed by repeated uplifts and warping along an anticlinal axis, differ-ential deposition of sands and shales contributing to great irregularity took place. This is further reflected by wide variations in permeability, porosity and thickness of all the sands and, accordingly, in the producing characteristics of wells. Permeabilities range as high as 550 millidarcies, with the average commonly lying between 60 and 100. For the three pay horizons the mean porosity is 18 per cent, at a calculated water saturation of roughly 30 per cent. The Weiler sand has an average thickness of 25 ft., the Benoist of about 23 ft. and the Paint Creek of approximately 18 ft. Of these three productive formations the Benoist

Jan 1, 1940

By S. H. Ash

Diesel locomotives, trucks, bulldozers, and other diesel-powered equipment are fast proving their superiority for mine transportation purposes. MORE than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance.1"0 This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago.7,8 Wumerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U. S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable. The best haulage equipment is subject to break- downs and accidents; but unless the rolling equipment, track, and signal systems are kept in good repair and are operated systematically, these breakdowns and accidents are likely to be frequent, destructive, and more costly than are necessary.10 Rail haulage crews using dependable rolling stock can move trips safely over grades low enough to be traveled without loss of control; this applies particularly if the track is straight and well maintained. Few accidents occur on main haulage lines if visibility and clearance are good and clear track is assured. One-way traffic underground is a recent development contributing to reduction of accidents and increased efficiency in mine haulage (Kelly mine, Anaconda Co., Butte, Mont., and Climax mine, Climax Molybdenum Co., Climax, Colo.)." Locomotives: Six types of mine locomotive used in recent years are trolley, storage battery, combination trolley and storage battery, diesel, compressed air, and gasoline. Electric haulage has been displaced by compressed air locomotives, which have been used successfully in certain instances, especially on dirty and wet tracks and steep grades." Maintenance cost is high, and operating efficiency, from a power standpoint, is low. Compressed air locomotives operate under self-contained power, and the absence of bare elec-

Jan 1, 1957