Search Documents

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?' In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.' occurred, data were combined.

Jan 1, 1958

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

From the beginning to the end, the attendance and enthusiasm of the 119th meeting, which was held in New York, Feb. 17 to 20 surpassed all expectations. Besides the ten technical sessions, one of which was in conjunction with the American Institute of Electrical Engineering and one a session of the National Research Council, there were two memorial meetings, one for Dr. Raymond and one for the members who died in service; two joint sessions with the Canadian Mining Institute; and a meeting devoted to pictures of copper mining, milling, and smelting. Of the 732 persons registered, 119 registered in the Institute of Metals Division. Monday's sessions were devoted to the problems of industrial organization, the Institute of Metals Division, and to petroleum and gas. Among the special features of these sessions were the topical discussions on housing and. Americanization. Americanization, too, was the topic for discussion by the Woman's Auxiliary Wednesday morning. On Tuesday, nearly 100-members of the Canadian Mining Institute were present to discuss the possibility of bringing about uniform mining laws for the United States, Canada, and Mexico, to obviate the maintaining separate legal departments and managerial forces for the several countries; and to avoid the confusion which, it is said, has led to a duplication of effort and has sometimes created a barrier to international cooperation in mining. Among the Canadian delegation were D. B.

Jan 3, 1919

Jan 1, 1907

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiCl-KCl mixtures, as first proposed by Guntz.2 The details of the industrial process have not been made public but Osborg8 stated that an efficiency of more than go pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of too kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, Si02, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units, such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, especially with respect to the iron and calcium content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1947

By N. F. Foster

The use of piezoelectric semiconducting materials for the fahrication of ultrasonic transducers has raised the upper fundamental frequency limit for transducers from about 200 mc to above 10 kmc, Several types of semiconductor transducer configurations have been proposed and examined experimentally. Depletion-layer transducers have been made and operated at frequencies below 1 kmc hut they appear to he better suited for operation at considerably higher frequencies around 10 knzc. Diffusion-layer transducers have been made and operated in the range 50 to 1000 mc and have exhihited considerably improved conversion losses and bandwidths compared with other transducers available in the frequency range. A variety of novel structures are possible using these new types of transducers, some of which could lead to substantial advances both in research and in the fabrication of ultrasonic delay lines and memory elements. THE field of ultrasonics today spans some five decades of the frequency spectrum from the audible to the kmc range and finds applications ranging from fundamental research into the atomic structure of matter to the degreasing of machine parts. To cover this wide range it has been necessary to develop a great many types of ultrasonic trandsucers utilizing a variety of materials and physical phenomena. The first ultrasonic transducers were made during World War I for a submarine-detection system. They consisted of plates of single-crystal quartz bonded between metal plates and were one of the first applications of the phenomenon of piezoelectricity discovered nearly 30 years previously. Despite the many advances which have been made in transducer technology, piezoelectric transducers using single-crystal quartz are still used almost exclusively for application above about 30 mc. Transducers at these frequencies are normally made in the form of thin quartz plates which are then bonded onto the medium in which the ultrasonic wave is to be propagated. The crystallographic orientation and geometry of these plates determines the type of wave generated and the way in which the efficiency of the electromechanical conversion varies with frequency. Analysis of the design parameters shows1 that the frequency of maximum efficiency (the fundamental or resonant frequency) is that frequency at which the transducer is approximately half the wavelength of the ultrasonic wave in the material. As the frequency increases, the ultrasonic wavelength, and therefore the optimum transducer thickness, decreases and in practice the fabrication of quartz transducers with fundamental freauencies above 100 mc becomes extremely difficult due to the extreme thinness required. For frequencies above 100 mc quartz transducers can be used in overtone-mode operation, and for very high frequencies (500 to 24,000 me) a technique using a quartz rod inserted in a high-Q microwave cavity4 is available. These techniques, however, exhibit comparatively low fractional bandwidths and rather poor conversion efficiencies. The present trend in ultrasonics is towards high frequencies and greater bandwidth to allow the use of shorter pulses which can give increased discrimination in radar-system delay lines and greater storage capacity in computer applications. The increasing demand for more efficient transducers with greater bandwidth

Jan 1, 1964

By Richard J. Gonzalez

The petroleum industry includes varied and extensive operations required to supply increasing quantities of refined petroleum products and natural gas that are essential for the economic progress of an expanding population Petroleum has provided the power for the transformation from the "horse and buggy days" to the age of jets and space exploration, and for the remarkable improvement in productivity per worker in agriculture and manufacturing. Without increasing quantities of oil and gas, the world would face painful readjustments to more expensive forms of energy and lower standards of living Petroleum operations start with exploration, development, and production activities that supply the basic crude oil and natural gas Pipelines, ships, barges, and trucks first transport the raw materials to processing centers and then move the finished products to the ultimate consumers. Processing plants extract liquids from natural gas and refineries convert crude oil into a wide range of products These products include transportation fuels, feedstocks for conversion into numerous products (such as fabrics, rubber, and plastics), light fuels for heating, lubricants, and heavy residual materials (industrial fuel oil, asphalt, and coke) The final activity of wholesale distribution and retail marketing moves products into millions of homes, farms, industrial plants, and motor vehicles The use of coal exceeded that of oil and gas until 1946 in the United States and until 1968 in the rest of the world. However, oil and gas have proved to be such convenient and attractively priced fuels that they now supply three-fourths of the total commercial energy (including coal, hydroelectric, and nuclear power) used in North America and more than one-half in the rest of the world. LARGE SCALE OF OPERATIONS By the beginning of 1970, world crude oil production exceeded 43 million bbl daily, -equivalent to more than 2200 million tpy In addition, natural gas and the liquids recovered from processing natural gas supply about 40% as much energy as crude oil Production of oil and gas provide by far the highest value of all mining operations. In the United States, the value of oil and gas production in 1969 of $13 8 billion exceeded the $13 0 billion value for all other minerals The rate of expansion in use of petroleum has been extremely rapid since World War II World crude oil production doubled from 7,500,000 bbl daily in 1946 to more than 15,000,000 bbl daily by 1955 It doubled again to 30,000,000 by 1965, and will double again by 1975 The use of natural gas has increased greatly in the United States and also in Europe, as important discoveries in the Netherlands and the North Sea and technology for moving liquefied natural gas from Africa provided attractively priced supplies

Jan 1, 1976

By C. A. Herbert

WITHIN the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the. Chicago & Northwestern R. R., the Chicago,. Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin Co., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mine, now in this field having nearly that output, but these were not planned for such

Jan 9, 1919

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be clone by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will he a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts. 1. SUBJECTS: The subject must be within the field of the Institute. Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasionally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper. The mere fact that the work is original does not necessarily justify publication: it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record. It is seldom desirable to subdivide the results of a single research for publication in a variety of journals. Previous publication is usually a bar to acceptance. If any part of your paper has been published elsewhere and you regard repetition as absolutely necessary please so state in your covering letter. 2. CONSTRUCTION: Papers should be clearly and concisely written in good English. Care in this regard ensures wider reading and the saving in space permits the Institute to publish more papers. It is the experience of the Papers and Publications Committee that most papers can he improved by condensation. "Readers" who are asked to recommend acceptance or nonacceptance put particular emphasis on the length of the paper and the elimination of unnecessary or any extraneous material. The terminology and units employed should be those current in the particular field. An examination of Institute publications will afford useful guidance in such matters. Webster's New International Dictionary, 1935 edition, is the Institute's authority for spelling and style. Various abbreviations are used habitually; for instance, lb., pound; bbl., barrel or barrels; ft., foot or feet; hr., hour or hours; in., inch or inches; Fig. 1 but Figs. 2 and 3.

Jan 1, 1946

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By J. E. Berry

AII evaluation is made of the acoustic velocity log for measurement of formation porosity. Plots of field-observer1 velocities vs core-measured porosities of sandstones and limestotnes with inter intergranular porosity show that the velocity log gives a useful measure of porotity, in agreement with published data. A new method of plotting electrical and velocity log data makes it easier to recognize hydrocarbon-water coritnct~ from log darn and to make serni-quantitative estinlates of hydrocarbon saturation. Two examples of this interpretation technique are given. This paper also discusses the various factors that affect acoustic velocity and shows how corrections can be made for some of these factors. INTRODUCTION Although the continuous velocity log was developed primarily as an aid to seismic interpretation, it is finding widespread use for measurement of porosity. The purpose of this paper is to evaluate this use of the log. Results are presented for the velocity-porosity relationship in many sandstones and one limestone. Practical applications of porosity values derived from the velocity log to improve interpretation of electrical surveys are presented. Various parameters which affect velocity in porous media are considered. Porosity, composition, cementa-tion, pressure difference (overburden pressure minus fluid pressure), fluid saturation, and wellability are discussed. Some of the ideas are opinions based on general considerations of well logging problems while others are supported by published data and our own observations. Major conclusions from these studies arc given in the body of the paper and detailed discussions of some of the various factors affecting porosity are given in the Appendix. POROSITY Sandstones The primary factor affecting the velocity of sound in porous media is porosity. Wyllie, et al,1 have reported a time average equation for the relationship between velocity and porosity.* This has found considerable acceptance in the industry. Other relationships between velocity and porosity have been proposed, none of which are entirely satisfactory. It is doubtful that any one relationship will completely describe all situations. We have tried an empirical relationship based on correlating log velocities with core-measured porosities. Measured porosities were averaged over a depth interval equal to the spacing used in recording the velocity logs. The depth range for the information used was from 2,000 to 12,000 ft. Velocity measurements were normalized for the effects of depth and overburden pressure. A detailed discussion of the basis for this normalization is given in the Appendix. The change is usually insignificant and when working with individual formations it can be neglected. All velocity measurements were normalized to a depth of 10,000 ft. The velocity-porosity data for sandstones in Fig. 1 came from 20 wells scattered throughout the Mid-Continent and Gulf Coast areas. The scatter of the data points is attributed to three causes: 1. There is no theoretical basis for expecting an exact velocity vs porosity relationship and it is not possible to correct precisely for the effects of such factors as impurities, grain shape, manner of cementation, etc. Some of these factors are discussed in the Appendix. 2. Porosities measured by core analysis are not necessarily representative of what the velocity log "sees". 3. Inaccuracies appear in the velocity log reading. This is particularly true of velocities from one-receiver logging tools.*" A linear-time curve (time-average equation) is plotted in Fig. 1 along with the best straight line through the points. Velocities used for the linear-time curves were 19,500 ft/sec for the matrix velocity (zero porosity) and 5,500 ft/sec for fluid velocity. For clean sandstones with velocities greater than 10,000 ft/sec, there is little difference between the velocity-porosity and the time-porosity curves. Both curves are well within the scatter of data points. The data points in Fig. 1 were restricted primarily to clean sandstones, using the SP and/or gamma-ray logs as clues to the lithology. Where a lithologic de-

By T. G. Madgwick, W. Calder

Production of petroleum increased again during 1929, thus maintaining the steady growth inaugurated by the bringing in of Royalite No. 4 in Turner Valley, Alberta, towards the end of 1924, prior to which a decline over a number of years had been experienced. The growth has been confined to the Province of Alberta, the older production in New Brunswick and Ontario showing declines, although in the latter case considerable activity in the search for new gas structures was maintained and during the last six months two wells were brought in, one at Howard in the Trenton at a depth of 1250 ft., giving 5,500,000 cu. ft., and the other at Tilbury in the Guelph or Salina at 750 ft. giving 9,000,000 cubic feet. As has been the case during the past five years, interest in the search for structure and in the following up and development of areas already recognized has centered in Alberta and adjacent portions of Saskatchewan. This was due in the first instance to the striking of wet gas in the Palaeozoic limestone (Madison) of Turner Valley, some 30 miles south of Calgary, in Royalite No. 4 in October, 1924. The bringing in of other wells of similar importance late in 1928 and in the spring of 1929 which extended the productive area 3 miles southwards led to greatly enhanced drilling activity throughout the structure and adjacent areas and in other parts of Alberta. As a result good strikes of heavy crude oil have been recorded during the year at Ribstone, Oyen, Skiff and Coutts, in each case at moderate depths and in sufficient quanitity to justify prolonged testing. The prospects of a satisfactory production of this grade of oil are very encouraging. Actual oil production in the west is still confined to the Province of Alberta and for all grades of oil totaled 997,359 bbl., which compared with previous years shows a gratifying increase. To this increase the naphtha obtained from the wet gas of Turner Valley has proved the principal contributant, heavy crude also showing an improvement, while the light crude, the product of the Cretaceo-Jurassic sands overlying the Paleozoic of Turner Valley, remains unchanged. This is largely owing to operators casing off these sands in their endeavor to reach the limestone, but, there is evidence that in future more attention will be paid to

Jan 1, 1930

By B. B. Cox

Since our last review of Iraq,' considerable progress has been made not only in exploiting Iraq's potential resources but in building pipe lines to carry the oil to the Mediterranean. No new fields were discovered in 1933. The Naft Khaneh field, discovered in early 1927 by the Khaniqin Oil Co. (subsidiary of the Anglo-Persian Oil Co.), continues to supply the local markets through the Rafidain Oil Co. Kirkuk field, discovered by the Turkish Petroleum Co. Oct. 14, 1927, remained shut in pending the completion of the Mediterranean pipe lines, and the Qaiyarah field, discovered by the same company on Oct. 13,1927, was abandoned in 1928. The principal development of interest during the year was the progress made on construction of the Iraq Petroleum Company's 1152-mile pipe line from Kirkuk to the Mediterranean. The line is double 10-in. and 12-in. pipe for 156 miles west of Kirkuk, where the parallel lines bifurcate, one leg going through British mandated territory to the new port of Haifa and the other through French mandated Syria to Tripoli. Each line may be operated independently of the other. There are three double stations on the Kirkuk-Haditha portion, four single stations on the Tripoli leg, and five on the Haifa in addition to a relief station in the Jordan Valley. Except for the Jordan Valley section and two other short stretches on the Haifa leg where pressures are exceptionally high, the line is single. Sea loading lines will be used exclusively at Tripoli and both sea loading lines and dock loading will be employed at Haifa. All pipe was welded and buried before the end of December, 1933. It is anticipated that enough stations will be completed to make 50 per cent capacity operation possible some time during the latter half of the current year. Some months will then be required in which to fill the line, so that if terminal facilities are ready and no unexpected emergencies arise, partial daily deliveries of Iraq crude may be received at the Mediterranean some time during the final quarter of the current year. Capacity operation of 84,000 bbl. per day is not anticipated much before the middle of 1935. Oil and Gas Production No gas is produced commercially and, except for Naft Rhaneh production, no crude is marketed. Although the Turkish Petroleum Co. and

Jan 1, 1934

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman' developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,' and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,' as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman's work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By E. P. Polushkin

The object of this paper as to show that the structural composition of an alloy may be found by the planimetric measurement of the total area occupied by each of the constituents on a few representative photomicrographs of this alloy. When the area is determined the volume and the proportional weight of the constituent may be calculated. This method has been used for the determination of the structural composition of binary eutectics and other binary alloys with known constituents; also the composition of unknown constituents in binary alloys. The accuracy of the method is. high enough to justify its application to metallographic problems instead of the chemical analysis. THIS work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that 'the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility, of determining the amount of the constituents with-out separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. DESCRIPTION OF PLANIMETER Suppose Fig. 1 represents a part of a photomicro-graph on which the total area of the black figures is FIG. 1?-PART OF PHOTOMICROGRAPH ON WHICH TOTAL AREA OF BLACK FIG- URES IS TO BE FOUND. to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively.

Jan 12, 1924

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By R. Frenkel, O. D. Sherby, J. E. Dorn, J. Nadeau

A method is shown for the study of the creep rate dependence of metals on the applied stress under the condition of constant structure. The method was applied to pure aluminum and to dilute solid solution alloys of magnesium, copper, germanium, zinc, and silver in aluminum. A linear relationship was found to exist between the true stress and the logarithm of the creep rate. ALTHOUGH extensive creep data are now avail-Aable, the fundamentals of the creep phenomena are as yet only vaguely understood. Many attempts have been made to formulate theories for creep. Eut their agreement with fact has been disappointing. It appears that merely pyramiding more of the same type of data that is now available will not provide the essential aid toward formulating a better understanding of the complicated process of creep. Perhaps attempts to construct better models for the mechanism of creep might have to be tentatively abandoned until new types of definitive creep data are uncovered. The question therefore arises regarding what type of data might be needed to provide the essential knowledge for formulating better and more realistic theories of creep. Perhaps one source of the failure to uncover an adequate theory arises from the fact that practically all theories for creep and nearly all analyses of experimental data on creep disregard the well-known fact that the structure of metals changes during creep. For example, it is customary in evaluating the effect of stress on the creep rate to correlate the secondary creep rate with the applied stress. But, as has been demonstrated recently,' the structures obtained during secondary creep tend to exhibit deformation banding at high stresses and polygoniza- tion at the lower stresses. Consequently the stress-secondary creep rate relationships found in this way are not fundamental, inasmuch as they reveal not only the effect of stress but also the effect of differences in structure on the secondary creep rates. It is the purpose of the study reported here to isolate the effect of stress alone on the creep rate in an attempt to provide new data for possible formulation of a better theory of creep. In addition an attempt will also be made to ascertain how structure, temperature, and alloying might affect the stress-creep rate relationship. The procedure that was adopted was simple: A specimen was precrept at a given engineering stress U, (initial engineering stress during creep under constant load, namely the load divided by the initial area of the specimen) and temperature T to a selected engineering strain, e (engineering strain, namely, the instantaneous gage length minus the initial gage length divided by the initial gage length), at which time the true stress was reduced to some lower value of the true stress, ^ (the true instantaneous stress, namely, the load divided by the instantaneous area). The instantaneous true creep rate, i, (the true strain rate; with E, the true strain, namely, the natural logarithm of the instantaneous over the initial gage length) following reduction of the true stress to U, was then determined. Second, third, etc., tests were conducted under identical conditions except the stress was reduced to yet lower values, us, u,, yielding yet lower instantaneous creep rates, ;, and i,. Inasmuch as the precreep conditions were identical in each series of tests, the instantaneous structures obtained immediately after reducing the stress were presumed to be identical.

Jan 1, 1955

By Peter J. Lean

The introduction oE computer control in the grinding circuit of the New Broken Hill Consolidated Limited concentrator in the early 1970's gave smoother operation at optimum performance. The ore feedrate and water additions to the grinding circuit were controlled to operate each of the ball mill/ rake classifier grinding units at the upper limit of the circulating load while classifier overflow density was maintained to give a product size and pulp density suitable for flotation. An incremental expansion of the concentrator in 1981-82 included the installation of hydrocyclones in closed circuit with three of the four ball mills. Without the rake classifiers in circuit the previous control strategy could not be used and the complex interaction of hydrocyclone performance characteristics when classifying coarse grained sulphide ore resulted in the over-grinding of the lead mineral galena. Testwork aimed at optimising grinding circuit performance recognised the enhanced tendency of higher specific gravity minerals to report to the cyclone underflow. The data has been evaluated on an individual mineral basis and then used to develop a model For grinding circuit control. The development of the model which uses inputs of ore feedrate, metal content of the Feed and slurry density of the cyclone overflow to predict the size of the minerals in the grinding circuit product is described and model predictions are compared with plant performance.

Jan 1, 1984

By George S. Rice

ARIAL maps of prospective mineral-bearing territory have become almost indispensable in all the branches of exploration, and have proved particularly useful in the great oil area of the Southwest. About nine years ago aerial photographic mapping in this area was begun. The early product was lacking in scale accuracy and other control features, which limited its effective use. Since then, the evolution of the technique of such mapping has been steady, with several mapping companies collaborating with five of the leading oil companies, and aerial maps have been prepared covering practically the entire area.Improvements in cameras, film, and developing equipment and practice have resulted in more uniform and clearer photographs, but the outstanding development has been the accuracy obtained with respect to scale and all other control features. Maps are no

Jan 1, 1936