Search Documents

By M. C. Udy, F. W. Boulger

AN incomplete phase diagram for the U-Ti systern was determined earlier 1 and more recently, a tentative diagram was presented for the uranium-rich end of the system.' In the present re-examination of the whole system of U-Ti alloys, high purity materials were used. Melting stock for the alloys was high purity uranium, containing about 0.09 pct C as the only appreciable impurity, and high purity iodide-process titanium purchased from New Jersey Zinc Co. Both metals were cold rolled to about 1/6 in. thickness, sheared to about I/' in. squares, and cleaned by pickling. The alloys were arc melted under a helium atmosphere in a water-cooled copper crucible. A thoriated-tungsten electrode was used. The furnace chamber was evacuated, then flushed with helium, prior to each melting. It was finally filled with stagnant helium at one atmosphere pressure. Each alloy was remelted three times after the original melting, to insure homogeneity. The alloy button was turned bottom side up before each re-melting operation. Some 22 alloys were examined. Their compositions were spaced at appropriate intervals between 100 pct Ti and 100 pct U. Analyses were made on chips taken after fabrication. The major contaminant was carbon, which varied from 0.03 to 0.08 pct. It appeared in the microstructure as titanium carbide. Alloy compositions were calculated to a carbon-free basis for consideration on the diagram. Tungsten and copper, possible contaminants from the melting operation, were generally less than 100 parts per million each. Fabrication All alloys were forged and rolled to bars approximately V8 in. square. They were clad either in SAE 1020 steel or in a 5 pct Cr-3 pct Al-Ti-base alloy, depending on the fabrication temperature. A temperature of 1800°F (980°C) was used for alloys near the compound composition. This necessitated using the titanium-base alloy, since iron reacts with titanium at this temperature, producing a low melting alloy. Other alloys were fabricated at 1450°F (790°C), using steel jackets. No iron-titanium reaction occurred at this temperature. The jackets were welded in place in an argon atmosphere. Those alloys sheathed in steel were declad and then reclad between rolling and forging operations. On the other hand, those clad with the titanium alloy were cut to a roughly rectangular shape prior to clading and were then carried through both the forging and rolling operations without opening. Those alloys near the compound composition were found to be cracked when the clading was removed. The cracked materials had been plastically deformed, however, and at least some of the cracking had OCcurred during cooling. Heat Treatment The rolled bars, after being declad and shaped to remove surface contamination, were all given an homogenizing treatment of 160 hr at 2000°F. (Samples were taken for analysis following the declading and shaping operations.) All were heat treated at the same time in one furnace, but each was sealed in a purified argon atmosphere in an individual Vycor glass tube. Argon pressure was such that it was approximately atmospheric at temperature. One end of each tube contained titanium chips and this end was heated to 1200°F (650°C) for 10 min prior to the heat treatment. This purged the atmosphere of residual reactive gases. The balance of the tube was warmed during the purge to liberate adsorbed moisture and gases, which also reacted with the hot chips. The bars were furnace cooled from the homogenization treatment. Specimens of each alloy were water quenched after 2 hr heating at 1000°, 1200°, 1400°, 1600°, 1800°, and 2000°F (540°, 650°, 760°, 870°, 980°, and 1095°C). In addition, some were treated at intermediate temperatures of 1300°, 1500°, and 1700°F (705", 815", and 925°C) and at 2150°F (1175°C). Specimens, about '/s in. cubes, were cut from the bars, sealed in individual Vycor tubes, and heat treated as described. All specimens heat treated at the same temperature were processed together. Samples were quenched by breaking the Vycor tube rapidly under water. Metallographic Examination Specimens were mounted in bakelite and ground wet on 180 grit paper held on a 1750 rpm disk. They were then ground wet by hand, using 240, 400, and 600 grit papers. The rough grinding was continued long enough to get well below the surface. Specimens were mounted separately because of the variation in the rate of etching between alloys. The specimens were polished with rouge on a 4 in., 1725 rpm wheel covered with Miracloth. Alloys on the titanium side of the compound composition were etched with a solution of 2 pct hydrofluoric acid in water saturated with oxalic acid. A few crystals of ferric nitrate were added as a bright -ener. Specimens were immersed 5 sec, polished to remove the etch, then re-etched. With the higher titanium alloys, it was often necessary to start the etch on the polishing wheel, because of the formation of a passive film. In some instances, a plain 2 pct hydrofluoric etch was satisfactory. For the alloys on the uranium side of the compound, a distinction between the compound and the uranium phase developed after standing a short time in air. This could be hastened by the application of heat, such as obtained by placing the specimen on a radiator. A deep etch was necessary to develop details in the uranium-rich phase, such as the Widmanstaetten pattern sometimes obtained by quenching y uranium. A 2 pct hydrofluoric acid solution was used for this deep etching.

Jan 1, 1955

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

E L. DEGOLYER, our new president, though a petroleum geologist by profession, has always s been associated with mining, for soon after his birth at Greensburg, Kan., on Oct. 9, 1886, his parents moved to Joplin, and when he went, in the course of time, to the University of Oklahoma, he intended to follow his course there with another at a mining school. He became a field assistant in the U. S. Geo-logical Survey, however, while still an undergradu-ate, and after field experi- ence in Montana, Wyoming, North Dakota, Colorado and Oklahoma, he went to Mexico as geologist for the Mexican Eagle Oil Co. This was in 1909, and as a result he was unable to complete his work for his degree until 1911. In Mexico, he located the Potrero de Llaño No. 4, one of the world's largest oil wells, and also the dis- covery well in the Naran- jos pool; and the Colorado School of Mines conferred the honorary degree of : Doctor of Science on him in 1925. On his return from Mexico, he engaged in the consulting business, specializing in financial ap- praisement, the Union and Marland companies being among his clients. In 1919, he organized the Amerada Petroleum Co., with the backing of Lord Cowdray. Last year, control of the company was purchased by an American group, headed by Dillon, Read and Co. Mr. DeGolyer is n o w president of the company. He is also vice-president and general manager of the Rycade Corp, the Rycade Oil Corp., and president of the Geophysical Re-search search Corp. The l a t t e r represents the practical appli-cation of his inter-est in the use of the torsion balance in the locating of salt domes, in which he has pioneered, the Nash dome being the first oil field in America actually brought into production by these methods.

Jan 3, 1927

By T. J. Koppenaal

The surface slip line structure has been investigated by optical microscopy during the easy glide deformation of Cu-A1 single crystals as a function of composition, testing temperature and prior thermal treatment. The slip line structure in alloys of 2.5 or less at. pct Al is similar to pure copper, while alloys of 5 or more at. pct Al show slip tracings typical of a brass. Cross slip is observed in the "a-brass type" crystals and the amount of this type of slip increases rapidly with aluminum content. The cross slip tendency in 14 at. pct Al crystals is signicantly higher when tested at 150°C as compared to 4.2" and 77°K. In addition, cross slip is more pronounced in this alloy in the furnace cooled condition than when quenched from 450°C. The cross slip behavior is analyzed in terms of existing models for this type of deformation. In two previous investigations, reports of yield points1 and solid solution strengthening2 in Cu-A1 single crystals have been given. This paper enlarges upon the brief description of the slip line structure discussed in these reports. Since the easy glide slip line pattern of copper changes markedly with the addition of -30 pct Zn (-brass),3 a study of slip lines as a function of solute additions in Cu solid solutions should help to explain some of these differences. In addition to composition variables, slip lines have also been studied as a function of testing temperature and prior thermal treatment. PROCEDURE The slip line observations were made on single crystals of 0.5 to 14 at. pct Al using a light microscope. Details concerning the preparation and basic testing procedure are given elsewhere.' Prior to testing, each crystal was homogenized at 900°C for 24 hrs, furnace cooled, and electrolytically polished in a 60 pct phosphoric acid solution. The strain rate was-5 X 10 sec-I in each case. Unless otherwise stated, all observations reported upon here were made during the early stages of easy glide. RESULTS AND DISCUSSION The maximum magnification generally used was 1000X, and slip lines could be resolved down to about 105 cm (1000A). This resolution is appreciably less than obtainable with electron microscopy replica techniques where the replication can resolve slip lines down to about 40 A. Thus, while many qualitative features could be studied, the type of quantitative data obtainable with an electron microscopy replica study could not be made. Crystals containing 0.5 and 2.5 at. pct Al deform much like pure copper exhibiting a high density of fine slip lines that cover the entire gage length of the specimens. Fig. 1 shows the surface slip line pattern in a 2.5 at. pct A1 extended 0.01 shear strain at room temperature. Crystals having 5 to 14 at. pct A1 showed appreciably coarser slip lines that were generally concentrated at one end of the gage length. During easy glide these coarse slip lines propagate along the gage length in a manner similar to that observed in a-brass single crystals by Piercy, Cahn, and cottrel14 and refered to by them as a Lüders band propagation. Fig. 2 shows a typical area of these coarse slips in a 14 at. pct A1 crystal after a room temperature shear strain of 0.01. Two slip systems were apparently active. Using a method described by Cullity, the angles, between the specimen axis and the normals of the primary and secondary slip planes were determined to be 50 and 84 deg, respectively. 'From the Laue photograph, was 52, 81, 66, and 30 deg for the primary, cross, conjugate, and fourth slip planes, respectively. The secondary active plane in Fig. 2 is thus established as the cross slip plane, and the operative slip system is evidently the cross slip system, e.g., slip

Jan 1, 1963

By Robert F. Mehl

THE purpose of a symposium, I take it, is to gather together a group interested in a common intellectual field, in order to exchange views, and to appraise the state of knowledge. Symposia are the more successful, the greater the activity in the chosen field and the wider the range of applicability of the information gained. From time to time, as emphasis changes from one field of research to another, a given subject may enjoy popularity and later retire into a scientific somnolence, for fashions change even among engineers and scientists. The subject of this symposium, however, enjoys the advantages of wide applicability and of high current interest and productivity in results. It is a timely subject for a symposium; with much new information, surely metallurgical engineers should now devote an increasing attention to its application to practice. In beginning the symposium, I shall attempt briefly to appraise our basic knowledge in the field, to survey instances of practical usefulness, and to suggest where new work might be most productive of useful results. There are many examples of direct practical application of diffusion knowledge, and it is the purpose of the several papers in this symposium to review these. In this introduction I shall attempt to take a broad view, which, while it will but poorly serve the engineer in the solution of any given problem, may perhaps be of some use in assessing the state of knowledge in this field. RATE OF DIFFUSION Liquid Metals The process of diffusion among liquid metals, of gases in liquid or solid metals, or among solid metals, is ubiquitous, to say the least. The manufacture of alloys by the intermelting of metals, the addition of ferroalloys to molten steel, the deoxidation of molten alloys, all involve diffusion in the liquid state. The oxidation of molten copper for purposes of purification, the unsought oxidation of alloys generally during melting and casting, the reaction of liquid steel with oxidizing slags in the open-hearth furnace, the absorption of nitrogen by liquid steel, particularly in the bessemer furnace, all operate by the diffusion of gases in liquid metals. These processes have not been studied much from the viewpoint of rates of diffusion. Alloys are made by melting metals with stirring and with allowance of time for mixing (which is diffusion) but I know of no studies that seem to define the necessary times, and though in only very rare cases can faulty properties of the finished castings be ascribed to inadequate mixing, and though certainly in most cases, with stirring, the rate of diffusion is adequate to give sufficient mixing, a more quantitative treatment would be good to have. It is not wholly certain that thorough and sufficient mixing is at all times attained, for I suspect that ferroalloy additions to steel, and that additions of aluminum to steel as a deoxidizer, especially in the sampling of steels

Jan 1, 1944

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

By L. L. Foley, C. V. Millikan

The discovery of Bromide production in the Fitts field, shallow production in Jackson County of Southwestern Oklahoma, abundant production in the Edmond field, and discovery of many small pools in all parts of the state, were the events that made petroleum history in Oklahoma in 1934. Wildcatting was much more active, as evidenced by a number of new discoveries. There was no important development in the older fields. The rapid decline of the potential of the Oklahoma City field was an important feature of the history of the year. The accompanying tabulation of oil fields (Table 1) is not complete. Many of the early records of operators and pipe line companies are lost and it will be impossible to work up complete statistics for a number of the older fields. The table includes most of the important fields of the state and includes fields of a number of different types. It is hoped that a great many additional fields may be worked up for next year's report. Fitts Pool.—The Fitts pool, in Pontotoc County, was discovered in 1933. Before the middle of 1934, the Pennsylvanian sands yielded -some oil at depths ranging from 1400 to 2800 ft. The Hunton series (Siluro-Devonian) produced most of the oil with considerable gas. In July, 1934, a well in sec. 25, T.2N., R.6E. was completed in the Bromide (Ordovician " Wilcox ") with an initial production of about 300 bbl. a day. Less than a month later a second Bromide sand well was completed in sec. 30, T.2N., R.7E., which made over 200 bbl. an hour. This started an active drilling campaign, which was accelerated when some of the major companies paid good prices for adjacent acreage. At the end of the year, 23 wells had been completed and the rate of development was increasing rapidly. It is a major oil field. The Fitts pool opened a new geological province for oil production. The structure is a faulted anticline in a graben. The producing formation (Bromide) and the Arbuckle lime below it crop out about 2 miles south of present production. The Hunton lime crops out about 2½ miles north. The field is in a sharply folded and faulted area on the northeast side of the Arbuckle uplift. Heretofore, it was generally considered not favorable for oil production, although some gas had been found in various places. The play has extended east into the McAlester coal basin, and southeast toward the

Jan 1, 1935

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

By AIME AIME

Report of Committee 24, of the International Association for Testing Materials, presented at the Brussels Congress, 1906. Republished for use at the 94th Meeting of the American Institute of Mining Engineers, New York, N. Y., February, 1908. Discussion by letter is requested by the Secretary of the Institute. The Committee appointed for the solution of Problem 24 consisted of the following members Prof. H. M. Howe, New York, N. Y. (Chairman); L. Levy, Paris, France (Vice-Chairman) ; Prof. D. Tschernoff, St. Petersburg, Russia (Vice-Chairman) ; Prof. Albert Sauveur, Cambridge, Mass. (Secretary) ; Van Drunen, Ixelles, Belgium; Lieut.-Col. H. Tusen, Copenhagen, Denmark ; E. P. Martin, Abergavenny, England ; A. Pourcel, Paris, France ; H. Brauer, Dortmund, Germany ; Dr. Prof. H. Wedding, Berlin, Germany; P. Verole, Milan, Italy ; A. Baalsrud, Christiania, Norway ; A. R. v. Dormus, Vienna, Austria ; A. Sailler, Vienna, Austria; Bureau des Forges, St. Petersburg, Russia; Prof. N. Belelub-sky, St. Petersburg, Russia ; N. Jossa, St. Petersburg, Russia ; Maj.-Gen. M. Korobkoff, St. Petersburg, Russia ; S. Smirnoff, St. Petersburg, Russia ;.Ladislaus v. Tetmajer, Budapest, Hungary ; H. H. Campbell, Steelton, Pa. Early in February, 1905, a list of species and varieties of iron and steel, with definitions, drawn by the Chairman and Secretary of Committee 24, was sent to every member of this Committee with a request for comments and suggestions. A special request was sent to the following gentlemen . for the equivalents in their several languages of these species and varieties : A. , Pourcel, Paris, France; Prof. H. Wedding, Berlin, Germany ; J. A. Brinell, Stockholm, Sweden ; Prof. H. I. Hannover, Copenhagen, Denmark; Prof. P. Kley, Delft, Holland; P. Verole, Milan, Italy; Col. Cubillo, Trubia, Spain. This present report, which is based upon our original list and definitions, and upon the replies to these requests, consists of four parts I. A polyglot, which gives the names of the chief classes of iron and steel in English, French, German, Swedish, Danish and Dutch. We .regret that we have failed to get the Italian and Spanish names. II. English definitions of principal classes of iron and steel. III. A glossary of special sizes and shapes of iron and steel. IV. A note on the boundary between steel and cast-iron. I. POLYGLOT, IN ENGLISH, FRENCH, GERMAN, SWEDISH, DANISH AND DUTCH, OF THE CHIEF CLASSES OF IRON AND STEEL, AND OF THE APPARATUS IN WHICH THEY ARE MADE. This list is not intended to be complete, but rather to include only those varieties which are of interest to the Association.

Mar 1, 1908

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is undcrlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production

Jan 1, 1938

By Don Rose

In the USA the cost of steel ribs for tunnels approximates $100 million each year. European practice has long since abandoned heavy steel ribs for tunnel support, and tunnel coats in Europe (normalized for wages) are about half the costs incurred in the USA. A feeling has existed for some time that the USA practices of supporting tunnels with heavy steel ribs have been overly conservative. The USA practice is based on rock load coefficients by Karl Terzaghi. In 1946, Karl Terzaghi published a tunnel rock classification system (Terzaghi, 1946), with the rock loads on tunnels predicted for each class of rock. No data on real rock loads were presented by Terzaghi and his rock load coefficients may have been largely intuitive. His classification system and associated predicted rock loads have been widely used in the USA. Each rock class, taken from Terzaghi's classification system, is assumed to generate loads of loosened rock resting as dead load. The dimensions of the loosened rock are described by rock load coefficients multiplied by the tunnel diameter. The resulting rock loads are used by design engineers, contractors and agencies to size supporting steel ribs. Terzaghi clearly stated that he had conservatively assumed high rock loads for his classes 4, 5 and 6 to take a presumed effect of groundwater into account. If the tunnel was not affected by ground- water, Terzaghi stated those rock loads should be reduced by 50 percent. Twenty two years later Tor Brekke (1968) wrote a paper clearly showing that based on observation of more than 250 tunnels groundwater does not affect tunnel rock loads. In 1969, Deere, et al., published measurements made on a number of tunnels, and a well-known curve was drawn by Deere to illustrate Terzaghios coefficients graphically. Deere's text stated that Terzaghi's predicted rock loads were too high and should be reduced. Cording and Deere (1972) more recently published data indicating that very large real rock caverns and chambers were being successfully built using rock bolts, which can take only a very limited rock load, thus indicating that real rock load is much smaller than Terzaghi or even Deere predicted.

Jan 1, 1982

By F. W. Jessen, G. F. Sears

Cavities in massive salt for the purpose of storage of liquid hydrocarbons have assumed a prominent position in recent years. This paper describes a program to facilitate leaching operations for the formation of specifically shaped storage cavities. Various forms and sizes of cavities may be possible through use of the techniques developed. INTRODUCTION The creation of large under ground storage facilities for natural gas and liquified petroleum gases has been practiced for many years. Use of cavities obtained through solution of salt for this purpose is a fairly new and novel approach, but has gained increasing importance due mainly to the economics of this type of mining operation opposed to hard rock mining or surface and pit storage.1 The idea of controlling the shape of any cavity dissolved from massive salt has not been a prime consideration of companies engaged in the formation of storage space. This has been due mainly to an insufficient knowledge of the mechanics of the leaching process and a dearth of published information dealing with both the desirability and ease of control possible for this type of operation. Two distinct advantages are readily ascertainable. From a stability standpoint (i.e., the ability of the completed cavity to withstand stress imposed by overburden pressure and lateral tectonic stresses) a controlled cavity may be generated which will yield the most favorable attitude to these external forces and remain in operable use for longer periods of time.2 A second advantage is that for a given volume, a sphere (which is one controlIed shape possible) represents the minimum surface area exposed. This may become more important in the future when dealing with refrigeration and product losses in underground cavities. The basic solution mining process, without regard for controlling the final shape, is quite simple in that the equipment and materials required to dissolve a cavity in a salt dome or layered salt section are a source of fresh water, a circulating pump, several strings of tubing and a means of disposal of the return brine. To add control measures involves the use of an inert blanket material above the position at which solution proceeds. Initially the annulus of the largest wash pipe is filled with this blanket down to the top of the proposed cavity. The bottom of the proposed cavity is determined by the depth of the original drilled hole or a blanking plug. The blanket material is added incrementally in stages and displaces the water in the enlarging cavity downward. Where the blanket material has displaced the water, no further solution takes place. The rate at which to add this controlling blanket material so as to be able to form specifically shaped cavities of any particular size is of considerable importance. THE PROBLEM It is desirable to have as much information as possible as to the behavior of the mining operation since visual observation obviously is impossible. It would be advantageous, for example, to have a step-by-step program showing how much salt is to be removed, at what rate and the time required. This type of program would facilitate procurement of surface equipment and provide for proper management of manpower requirements, as well as yield a host of intangible benefits. As mentioned earlier, only rule-of-thumb estimates were available until recently and made this type of pre-planned operation haphazardous at best. Recent work3-' has done much to clear up the ambiguities and inaccuracies attendant to solution mining of salt and has helped to place the operation on a more scientific basis. This study attempts to correlate much of the information thus far developed into a complete mining program; to extend the idea of controlled solution mining to include not only spheres, but solid conic sections of the ellipsoidal variety; and to refine the computation of the rate of removal of salt during the various stages of mining. Dommers3 and IIemson4 made extensive laboratory

Jan 1, 1967

AT the meeting of the Board of Directors in March 1945, plans were discussed for a special General Meeting to commemorate, in an appropriate way, the founding of the Institute at Wilkes-Barre, Pennsylvania, in 1871. It was decided that seventy-five years of growth, progress, and achievement; of service to the profession, to the mineral industry in all its branches, and to society at large should be fittingly celebrated. Harvey S. Mudd, then President of the Institute, was authorized to appoint a General Committee on Arrangements as well as necessary working committees. On June 6, 1946, Louis S. Cates, as President, at a special meeting of the Pennsylvania-Anthracite Section at Wilkes-Barre, officially announced plans or a three-day meeting to be held at The Waldorf-Astoria, in New York City, September 16-18, 1946. Four major sessions to be addressed by eminent speakers had been-planned in some detail to constitute a "World Conference on Mineral Resources." The U. S. Department of State had dispatched a 1500-word airgram to all its diplomatic posts giving worldwide publicity to the scope and importance of the meeting; and formal invitations had been issued to more than 150 institutions in 40 foreign countries to send official delegates. These included scientific and engineering societies, educational institutions, and sundry government agencies connected with the mineral industry. However, about a month later it was found necessary to postpone the celebration. The reason was an unforeseen expansion in the requirements of the United Nations for hotel living space in New York to accommodate delegates to the meeting scheduled to start September 3; and, of course, U.N. delegates would be given priority. It was decided to postpone the Celebration-conference to the week beginning March 17, 1947; t6 devote the first three days primarily to the Celebration; and to follow it with the technical sessions, committee meetings, and other functions, that are regular features of the Annual Meeting. To accommodate the combined "show" it would be necessary to hold some of the Annual Meeting sessions at another hotel;

Jan 1, 1947

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By C. W. Washburne

Continued discussion of the paper Of ROSWELL H. JOHNSON, presented at the New York meeting, February, 1015, and printed in Bulletin No. 98, February; 1915, pp. 221 to 226. See also Bulletin No. 101, May, 1915, pp. 1157 to 1162, and No. 103, July, 1915, pp. 1449 to 1450. C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Mr. Johnson recognizes that connate waters must be driven, outward toward the earth's surface. He considers the ascent due to the settling and packing of the underlying sediments and to the formation of gas within the rocks, supplemented by abyssal pressures. The origin of the methane in the sedimentary strata probably is not simple. There are three possible modes of origin: (1) as marsh gas formed near the surface and entrapped in the sediments; (2) from abyssal sources; (3) by the decomposition of organic matter buried in the sediments. The abyssal source is generally negligible, and in all cases doubtful. The third origin is the most important in the gas fields. A fourth mode of origin, by the dissociation of liquid hydrocarbons, frequently has been suggested, but it is improbable, because crude oils are exothermic. Therefore they have no tendency, to split or decompose at low temperatures, as do endothermic substances, such as coal, which is geologically by the loss of methane, water, and carbon dioxide. This cannot happen to a hydrocarbon until its temperature of dissociation (" cracking point") is reached, which is over 250'.C. for the most easily cracked hydrocarbons and over 400° C. for others. Engler says that the dissociation of fats and waxes into oils is an endothermic process, thereby unconsciously nullifying his own theory of the dissociation of these substances at low temperatures. However, recently I have found reason to think that heat is liberated by the disruption of the molecules of fats and waxes, as it is in the molecular decomposition of the substances of wood, coal, etc. If this tentative opinion is correct, and Engler wrong, then it seems that the Engler-Höfer hypothesis of the origin of oil becomes not only possible, but even probable.

Jan 9, 1915

When the suggestion was made by Major General Leonard Wood that the Institute assist in the formation of a National Reserve Corps of - Engineers, Dr. Drinker's name occurred first to the Board of Directors as the man who would be most capable of carrying out the proposed plan. Dr. Drinker has long been associated with work in connection with military training and is at present the Chairman of the Governing Committee on Military Training Camps Association which is having such important results at Plattsburg and other places in this country. As Chairman of the Institute's Committee on National Reserve Corps of Engineers, Dr. Drinker was a member of the Joint Conference Committee of the National Engineering Societies .on. this subject., He was an earnest worker in the movement, which, has finally resulted in definite legislation by Congress; whereby a Reserve Corps of Engineers is authorized in the new Army Bill which became effective July 1, 1916. Notice of the results of the work was sent to all the members of the National Engineering Societies early in July, and the and the Department of the United States has recently issued a circular which has been sent to all the members of the National Engineering: Societies, as well, as to many other engineers, outlining, the line, whereby engineers may enroll themselves in the Officers Reserve Corps. Dr. Drinker has, therefore, fulfilled the mission which he undertook when assuming the Chairmanship of the Institute's Committee. He now asks the permission of the Board of Directors to withdraw as Chairman and has requested that he be replaced in this position by Mr. Arthur S. Dwight, in; the belief that the Chairmanship of the Institute's Committee and, membership on the Joint Committee should be vested in a man ,located in New York City, for the better carrying put of the important work now before the Joint Committee. We are happy to say that Dr. Drinker has consented to remain a member of the Institute's Committee; but the completion of the first phase of his work; as,Chairman, should not be allowed, to pass without an expression of appreciation on behalf of the Institute for his services.

Jan 9, 1916

By J. Chipman

There is no better way of paying tribute to the memory of a scientist than by developing and carrying forward those ideas which he has contributed to science and which are for us the very essence of his immortality. For a lecturer who has not had the great privilege of stdying under Professor Howe or 'ven of knowing him in person, these ideas must be transmitted through the printed word. It is our great good fortune that Professor Howe left to us a rich heritage of publication, not only in his classic monograph on the "Metallography of Steel and Cast Iron" but in a wealth of earlier hooks and papers in the transactions of this Institute arid of other scientific and engineering bodies. An outstanding characteristic of this published record is the great breadth of interest and of vision which it portrays. His was riot a narrow specialization in only the scientific aspects of ferrous metallographg. On the contra1y many of his important contributions had to do with a far broader field of metallurgicial endeavor. He insisted that his students be well grounded in 1 he fundamentals underlying the whole field and not led into the narrow groove of specific applications. Among his first major publications we find papers on copper smelting, extraction of nickel, the efficiency of fans and blowers, thermic curves of blast furnaces, the cost, of coke, and the manufacture of steel. These are the papers of a metalhurgical engineer and it was among engineers that Henry Marion Howe made his early and well-merited reputation. These early engineering contributions display very clearly the strongly sctientific inclination of their author. The classic work on "The Metallurgy of Steel" published in 1890 contains a thorough and critical discussion of all that was known at the time concerning the alloys of iron and of what we would now call the physical metallurgy of steel. In addition it describes steel-making processes in use and some that had become obsolete, and points out in critical fashion the reasons for success and failure. Steel mill design and layout were included as well as some pertinent discussion of refractories. The book is indeed an embodiment of one of Howe's outstanding characteristics—breadth. It is both the science and the engineering of steel production as known in that day. One of Howe's earliest technical papers was entitled "What is Steel?" That was nearly seventy-five years ago when many new processes and new kinds of steel were being developed. The time was ripe for such a question and the answers which Howe was able to give were helpful in understanding the phenomena of heat treatment. Twenty-five years ago Professor Sauveur repeated the question as the title of the first Henry Marion Howe Memorial Lecture. It seemed to him that this question, "What is Steel?," had served as Howe's motto throughout the remainder of his life. Today I shall present for your consideration a question of another sort: "What is Sletallurgy?" Perhaps it is not too much to hope that in the answer we may obtain a clearer and possibly broader view of the nature of our science and our profession. The time is ripe for giving careful consideration to what we mean by metallurgy. If our Metals Branch is to become in fact an American institute of Metallurgical Engineers, it is essential that we understand what is meant by metallurgical engineering. I am convinced that the best interests of the profession have not been served by a narrow interpretation of these terms. We must now place emphasis on the breadth of metallurgy as a science and as an engineering profession. With its usual brevity and wit. Webster's dictionary definesmetallurgy as "the science and art of extracting metals from their ores, refining them and preparing them for use." I shall riot assume that the words "science" and "art" and "metal" are so well understood as to require no defining but others among our contemporaries are better qualified than either your lecturer or the dictionary to present the broad meanings of these terms. When we say that metallurgy is among the oldest of the arts we are not classing it with painting or sculpture or music but rather with the making of tools or weapons or the building of bridges or chariots or cathedrals. In short we are saying that metallurgy is among the oldest of the engineering professions. The question " What is metallurg ? " has been one of rather more than ordinary concern to those of us who have the task of developing a curriculum for the education of students in this field. This development has been going on in a number of universities over a period of some years. but there seems to be as yet no unanimity as to what such a curriculum should contain. I believe there is fairly complete agreement that it must be founded upon sound

Jan 1, 1950

By Kenyon Burch

ONE of the advantages presented by electric drive in many classes of work is the ease with which the electric motor can be controlled automatically. In a large number of cases certain features of the control are automatic-for example, the rate of acceleration may be limited automatically or the equipment may be stopped automatically at the limit of travel-but the equipment is started and ordinarily is stopped by hand. . In other cases the motion of the machinery is utilized to start, control the: speed, and stop the motor automatically, independently of any operator. A considerable proportion of the large mine hoists now in use have certain automatic features, particularly protective devices against over-winding, and, in some classes of electric hoists, devices for preventing excessive acceleration or retardation. The large automatic hoists discussed in this paper, however, are completely automatic, i.e., capable of snaking their trips without the presence of an operator at the control levers. According to circumstances, various advantages may be obtained by automatic control, chief of which are decreased power consumption', increased precision and safety of operation, and decreased, cost of attendance. The first step in the analysis of a prospective automatic mine hoist is to determine whether automatic operation is feasible at all. If men are to be hoisted, or levels changed, the attention of an operator is required for these purposes; but tinder some conditions it may be entirely practicable and advantageous to build the equipment so that, while provision is made for hoisting mien or changing levels, ore can be hoisted automatically from, any one level. If, however, an operator's attention is required every few minutes for changing levels, handling men or drills, or other work requiring hand control, it is obvious that automatic operation between times will not be of any, practical benefit.

Jan 3, 1916

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953