Search Documents

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By J. F. Pierce, S. M. Enterline

Since January 1959 a zinc refiner of novel design has been in operation at Blackwell, Okla., producing 99.995+ zinc from the output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyro-metallurgical unit with principal dimensions horizonhl permitting one floor operation. It is very ruggedly constructed. Furthermore it is not subjected to deterioration from high concentrations of iron in the feed metal because the boiling units are separate from the rectification columns and constructed with silicon carbide brick arches through which the heat is transferred radiantly to the zinc. A zinc refiner of novel design has been in operation since January 1959 at the Blackwell, Okla. plant of the Blackwell Zinc Co., Inc., a wholly owned subsidiary of American Metal Climax, Inc. Developed by the company's technical and operating staffs, the new refiner produces special high-grade zinc (nominally 99.995+ pct Zn) from the prime western1 slab output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyromet-allurgical, high-capacity unit employing fractional distillation to separate zinc from its impurities, consisting principally of lead, cadmium, and iron. In prime western slab, these elements may vary in concentration from 0.005 to 1.6 pct. Table I shows the impurities usually encountered in the Blackwell prime western metal fed to the refiner together with their boiling points and vapor pressures at 907oC. The commercial pyrometallurgical smelting processes for extracting zinc from ore include distillation from retorts and a limited degree of refining can be accomplished by redistillation in similar retorts. To achieve special high-grade purity, an impractical number of batch redistillations would be required, however, with an accompanying loss of much metal. A continuously operated and integrated unit is required in which fractional vaporization and condensation can take place in a large number of stages. The first commercial continuously operated unit was developed by the New Jersey Zinc Co.4 In the separation of any two substances the degree of separation is limited if a mixture exists having a constant boiling point. The Zn-cd5 and Zn-pb6 systems contain no constant boiling points and hence these metals may be separated to any degree of purity. Basically, the pyrometallurgical refining of zinc involves three steps: a) iron, copper, and other metals having no appreciable vapor pressures at 907ºC concentrate in the bath when the impure zinc is boiled, b) lead, bismuth, antimony, and other metals having boiling points above but closer to that of zinc are selectively condensed from the vapor boiled from the bath, and c) cadmium and other metals having lower boiling points than zinc are fractionally distilled by reboiling and subsequent condensation of the zinc from the vapor. The boiling and condensation of zinc must be conducted in vessels constructed of materials which are refractory at the temperature involved (907 ºC) and it is highly desirable that they also be resistant to attack by the various metals. This requirement dictates construction from relatively small, simply shaped pieces which limits the pressures which may be employed to avoid leakage through the numerous joints. Stresses induced must be limited essentially to compressive ones and suitable provision must be made to permit thermal expansion of the components in order to minimize these stresses. Where heat is to be added for boiling or removed for condensation, refractory material through which the heat flows must have a high thermal conductivity. Silicon carbide is highly conductive but is subject to attack by iron and is expensive compared to other commonly employed refractories. A hard, dense aluminous fireclay is well suited to contain these metals where high thermal conductivity is not required. Zinc will penetrate the pores of fireclay brick but only to a limited depth in an exterior wall and has little effect other than an increase in weight and conductivity. The design objectives of the Amax refiner were: a) to achieve a long life by heavy, rugged construction and by employing silicon carbide refractories only where required for heat conductivity and not in contact with liquids of high iron concentrations, b) to simplify operation, manning and control by essentially horizontal construction, and c) to obtain high capacity in a single unit. DESCRIPTION Flow of metal through the Amax refiner is shown diagrammatically in Fig. 1 and schematically in Fig. 2.

Jan 1, 1963

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article' describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation. Some attempts were made in 1931 by the owners of the Hawkesworth patents to interest Ontario gold mine operators in the bit. These efforts were not successful, but they undoubtedly stimulated thinking which resulted in the invention and patenting of several well-known Canadian detachable bits, one of which is now a widely used throwaway bit. The success of the Butte installation also led to the development of the threaded type of bit connections by several well-known manufacturers, and in 1935 these bits were introduced to the mining industry on a national scale. The original Hawkesworth bit was not provided with a water hole but, depended upon water passing through the clearance opening between the tongue in the bit and the groove in the rod to flush cuttings from the drill hole, see Fig. 1. In December 1935 it was found that this method of introducing drilling water to the bit face resulted in high dust counts. To correct this a water hole was drilled on the central axis of the bit, passing through the tongue. Unfortunately, quenching water would rise through the small water hole, spot-hardening the tongue to cause breakage, never completely eliminated. In the fall of 1936 large-scale tests indicated that savings would be effected by use of a threaded type of bit, which was therefore adopted as standard for all Butte mines. This type of bit was used until 1947, when it was superseded by a one-use slip-on type. Since the first use of the Hawkesworth bit every detachable bit of importance has been investigated, and where advantages which might reduce costs or increase efficiency were indicated, substantial tests of the bit were carried on in the Butte mines. When tests demonstrated the advisability of changing from one kind of detachable bit to another the change was made at one level or in one area each day until the new rod and bit equipment was used throughout the mine. This involved a minimum of cost and disruption of drilling. Intelligent selection of a detachable bit to obtain optimum results requires careful consideration to achieve a balance between the three principal types of equipment used in the drilling process: 1—drill bits, 2—drill steel, and 3—drilling machines. Optimum results imply maximum output and minimum cost per unit of output. Since every rock type differs in drillability and it is generally impractical to provide equipment for more than one or two types of rock which may occur in one operation, selection of equipment must encompass average drilling conditions. However, on exceptional occasions several widely differing conditions may make it mandatory to provide equipment best suited to each condition. The choice of rock-drilling equipment is a most controversial subject and one that is further complicated by unreliable and frequently misleading performance claims. Small operators without the means for making accurate evaluations of equipment frequently suffer from these over-enthusiastic claims. It is apparent from experience in rock drilling throughout the world that rock drillability is not alike in any two places, and that selection of proper equipment can only be made after conducting thorough trials of various types of equipment. Some recent drilling tests in tactite and hornstone at the Darwin, California mine of the Anaconda Co. present some interesting clues on rock drillability. Microscopic examination of thin sections of these rocks reveals that mineral composition and rock texture are equally important in governing drillability. The Darwin hornstone is at times so abrasive that the carbide bit cutting edges become flattened to 3/32 in. in 2 to 4 ft of drilling, and some carbide bits were dulled to this point after 9 to 10 in. of drilling. This wear was determined to be the proper point for resharpening to eliminate carbide insert breakage or breakage of the steel rod when drilling with 1½ to 1?-in. bits, with a drifter of 2 3/4-in. diam and 90 to 100 psi air pressure, see Supplement A. Before considering the merits of various bit designs it may be well to review the mechanics of drilling rock with percussion drills. A sharp bit cuts by penetration and chipping. The amount of penetration governs the amount of chipping and depends upon the contact area of the cutting edge, the foot-

Jan 1, 1954

By Jean Herenguel

THE published work of Lacombe and Beaujard' has demonstrated the interesting application of etch figures to the determination of crystal orientations in aluminum by a purely micrographic method. The geometry of these figures leaves no ambiguity and the method has the added advantage of being applicable to very small crystal units. These authors applied the technique to the study of high purity aluminum, and it has now been adopted buy Heren-guel and his collaborators to various researches on commercial aluminum, containing up to 1 pct Fe and Si. This must modify the opinion point,ed out by

Jan 1, 1953

By T. J. Neil, C. B. Manula, O&apos

This paper describes a simulation model developed to analyze truck haulage problems as they are found in the open pit mining and construction industries. The model, using a computer, cycles trucks between their assigned loading and discharge points over a measured haulage route. Required parameters for model operation include the number and type of operating trucks and loading units, maximum truck acceleration and velocity, a realistic vehicular deceleration rate, and the ratio of ore to total material loaded at each origin. Equipment performance characteristics, system profile characteristics, and service time distributions are also included. Records are kept of all waiting times at the loading and discharge points and of any truck interference on the haulroads (moving queues), and a current journal of ore and waste production is maintained. In the pursuit of reduced truck haulage costs, management is confronted with three particular problems in truck and shovel mines. 1) What is the best assignment of trucks to shovels in the system? 2) If new equipment is needed, which new shovels and trucks will operate most effectively in the system? 3) Are any physical changes in the haulage layout warranted to increase productivity? For small open-pit mines the answers to these questions may be obvious. However, for larger operations complex problems are encountered with production and system configuration relationships usually being unknown. The mining simulator discussed here was developed to aid management in evaluating alternative pit-haulage schemes to reduce the risk involved in the selection and assignment of equipment in open-pit truck and shovel mining systems. There are two fundamental differences between this model and other truck haulage simulators: one is a difference of degree, the other a difference of kind. This model can simulate more complex systems than previous models by allowing transportation of material from multiple mine faces to multiple mine destinations and by being readily adaptable to a wide variety of mine layouts. The second difference that characterizes the model is the standard simulation of truck movements. This technique enables each vehicle to perform according to its mechanical capabilities and the physical profile of the haul road. Among the similarities between other truck haulage simulators and this model are the recognition of the probabilistic nature of certain service times in the system and the use of a digital computer to operate the model. The computer inherits the staggering computational and bookkeeping work loads and provides a means for compressing the time scale by allowing several days' operations to be simulated in a matter of minutes. DISTRIBUTION SYSTEM Basic aspects of the system analyzed here may be brought into focus by referring to Fig. 1, a schematic of the typical open pit truck-shovel operation programmed into the simulation model. A single stage materials handling scheme is employed to transport both ore and waste. Loaded trucks are directed to a crusher or stockpile if ore is being mined, while overburden is conveyed to a waste dump. Each shovel has a given number of assigned trucks and has two associated haulage routes, one for waste and one for ore. Up to 5 shovels and as many as 10 trucks per shovel (or a total of 50 trucks) can be operated in the model. Essentially the model, using a computer, cycles trucks between their assigned shovels and the proper discharge points over measured haulage routes. Required input parameters for model operation include the number of shifts to be simulated, operating time per shift, number and type of operating trucks and shovels, maximum truck acceleration and velocity, a realistic vehicular deceleration rate, and the ratio of ore to total material loaded at each shovel. Equipment performance characteristics, system profile characteristics, and service time distributions are

Jan 1, 1968

By S. E. Hasko

It is the purpose of this note to report the crystal-lographic data for nine new B5A compounds* having the Cu5Ca structure, with A a rare earth and B a transition element, Co, Ni or Cu. In previous papers, some magnetic data1 and preparation and crystallo-graphic data2 for other B5A compounds having the same structure have been reported. Crystallographic data for these compounds are shown in Tables I and 11. These results are in agreement with others of this series reported previously by Wernick and ~eller.' The abnormally large atomic volume of Yb metal3 is not manifested in Ni,Yb, when one compares it with the compounds reported here and the data of reference 2. This is not true for the compound YbAl,, having the cubic Laves structure (MgCuz), to be discussed in other papers.4'5 Thus, it appears that Yb has a valence of 3; i.e., the 2 s and Id electrons are lost to the conduction band.4'5 Lattice constants for four of these compounds prepared by levitation melting have been reported by Nassau, Cherry, and wallace.' The lattice constants

Jan 1, 1961

By H. M. Chance

The recent discoveries of important new gold-districts in limestone, granite, sandstone and porphyry have awakened the more intelligent class of prospectors to a realization of the fact that ally rock may be gold-bearing; that from the appearance of a rock it is impossible to judge whether it carries gold or not; and that gold-ores may occur in any geological formation. As a rule, the professional prospector limits his search to ores and conditions with which he is more or less familiar, and to formations which he regards as favorable to the occurrence of such ores. Hence it often happens that while the very thing he is searching for is in plain sight, he fails to recognize it, and some other individual, possibly less intelligent but more lucky, stumbles blindly upon it. Beginning with the discovery of the California placers by the finding of gold in the tail-race of Sutter's saw-mill—a tale so often told that nearly all have read it in some form—and following the discovery of district after district down to the present time, one is forcibly impressed by the fact that many of the important districts have been discovered by accident; that many such discoveries have been made by unskilled or inexperienced prospectors, and some by persons having no knowledge whatever of prospecting. Thus, the recent Klondike discoveries are said to have been made by a poor salmon-fisherman, who, with his Indian wife, was hunting, not for gold, but for good fishing-grounds; the Comstock lode is said to have been accidentally discovered, and the Ragged Top district in the Black Hills and the Pearce mine in Arizona* are recent notable instances of the same kind.

Jan 1, 1900

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove' In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove' In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By M. Cohen, S. A. Kulin

AT a recent symposium on thermodynamics in physical metallurgy1 two opposing theories of the austenite-martensite transformation were presented. Both theories agreed that this type of reaction involves a nucleation process which requires activation and that the activated nuclei develop into the well-known martensite plates with tremendous speed. However, there were essential differences in the two points of view concerning the nature of the nucleus and the mechanism by which the nucleus propagates. According to Cohen, Machlin, and Paranjpe,' the nucleus is a strain center with sufficient elastic energy to initiate a cooperative displacement among the atoms of the parent phase when a sufficiently low temperature is reached. This displacement propagates as a wave in shear-like fashion to transform the austenite into martensite without benefit of diffusion. On the other hand, Fisher, Hollomon, and Turnbull3 regard the nucleus as a solute-poor region (in the austenite) of a size which becomes supercritical relative to coherent growth into martensite when an appropriately low temperature is reached. This growth process is taken to be an atom-by- atom transfer from the receding austenite lattice to the advancing martensite lattice through the coherent interface that exists between the two phases. The present paper is not conceded with the divergent views as to the nature of the nucleus but describes some critical experiments which differentiate between the two proposed mechanisms of propagation. Fisher' has summarized the latter issue in the following way: According to the cooperative displacement theory, the speed of formation of mar-tensite plates should not be decreased by lowering the temperature, and martensite should form with extreme rapidity at very low temperatures; whereas with the alternate growth process, the speed of the martensite transformation should be retarded at very low temperatures, decreasing to zero at the absolute zero. The atom-by-atom growth mechanism predicts a marked slowing down of the reaction rate with decreasing temperature because the rate of self-diffusion in the austenite is involved in this picture. For example, Fisher, Hollomon and Turn-bull5 estimate that the activation energy for this growth process in steel is (0.34)2(0.36)* times the activation energy for self-diffusion in y-iron. The two most recent determinations of the latter quantity are 67,900" and 74,2007 cal/mol, which may be averaged as 71,000 cal/mol. This, in turn, gives a value of 3000 cal/mol for the activation energy of the atom-by-atom process, and hence the rate of growth should vary as e 8,000/RT where R is the gas constant

Jan 1, 1951

By R. Maddi, I. R. Kramer

C. S. Roberts (Dow Chemical Co., Midland, Mich.)— In this study we have seen another example of how modern electronic instrumentation can be of great value to metallurgical research. The authors have shown much ingenuity in their experimental work. However, I wish to point out that anelasticity theory tells us that we must be cautious when we use pulse methods for measurements which are to be correlated with knowledge of static stress-strain behavior. The basic stress calibrations used by the authors depend on the use of static moduli combined with the pulsed strains. No recognition of a possible modulus defect has been indicated. The general agreement of critical resolved shear stresses may indicate that a

Jan 1, 1953

By AIME AIME

THE session* on Non-ferrous Metallurgy held Monday morning was conducted in a most satisfactory manner with F. F. Colcord, vice-president, U. S. Smelting Co., in the chair. In spite of the early hour and the fact that members desired to register first, the meeting started quite promptly, with almost every chair in the room occupied. About 65 men were present and during the morning many more came but, not being able to find room, drifted away to other fields of activity. The first paper presented, "Lead Refining Practice of the Bunker Hill Smelter of the Bunker Hill & Sullivan Mining & Concentrating Co.," by Alfred F. Beasley (T. P. 303), was read in abstract by Edward H. Robie, and an animated discussion followed in which Messrs. Johnson (written discussion), Brewer and Jones and Professor Hayward participated. The discussion hinged principally on the liquation of the zinc crusts, but Professor Hayward called attention to the fact that the practice of keeping the gold and silver crusts separate was not new and the present scheme illustrated the axiom that processes based on fundamental principles should not be considered as extinct; one can never tell when it may be found advantageous to make use of them again.

Jan 1, 1930

By D. J. DeLazaro, D. W. Levinson

Observations were made of the isothermal transformation and quench and reheat transformation characteristics of binary titanium alloys containing nominally 6 wt pct and 10 wt pct Mn at temperatures of 700°, 600°, 500°, and 400°C. A large change in electrical resistivity attends the beta to alpha transformation in these alloys. The correlation between the resistivity and microstructure provides a very sensitive means of following the transformation. IN a recent paper, Wyatt' determined the electrical resistivity of several grades of unalloyed titanium metal as a function of temperature. In addition to the expected discontinuity accompanying the a-B transformation, it was shown that s-Ti has a much larger temperature coefficient of resistance than 8. The result would be a very large change in resistivity attending ß?a: transformation if it were possible to retain the ß structure at room temperature in pure titanium. From these data, it was reasoned that this very large resistance change should accompany the decomposition of the ß phase in alloys in which the ß phase can be retained by quenching to room temperature from the ß field. This effect is illustrated schematically in Fig. 1. Binary Ti-Mn alloys containing more than 5 wt pct Mn can be quenched to retain ß from the ß field. While the ß phase would be expected to transform in these alloys to a + TiMn via a eutectoid reaction,' it has been observed that the eutectoid decomposition does not occur readily in hypoeutectoid alloys, but rather the decomposition of the ß occurs by rejection of proeutectoid a only." Thus, the resistivity should show a marked decrease, as the a: phase is rejected from ß and a study of the resistivity of solution treated and isothermally transformed or quenched and reheated alloys should provide an excellent means of establishing the transformation kinetics of these alloys at various temperatures. The usual metallographic method of determining the transformation temperature-time characteristics of alloys of this type is very satisfactory for deter- mining the time required to initiate the rejection of the a phase at temperatures relatively close to the ß/a: + ß boundary when the rejected a is coarse, and a typical Widmanstaetten structure is produced. The metallographic method is less satisfactory for this purpose at lower temperatures where a fine nodular decomposition product is observed and is very unsatisfactory for the determination of the time required to complete the transformation at any temperature. Accordingly, specimens were prepared for resistivity measurements in order to determine the transformation characteristics of the alloys.

Jan 1, 1955

By E. P. Barrett, T. L. Joseph

The large iron-ore producers on the Mesabi Range are able to maintain the silica in their shipping products at from 8 to 10 per cent. by mixing ores of various grades, some assaying 4 per cent, silica and some as high as 18 per cent. silica. For each ton of 4 per cent. silica ore mined, a ton of 14 per cent, silica ore can be mined and mixed with it and the average grade maintained at 9 per cent. This mixing operation has made possible the utilization of large quantities of ore too lean to be used alone, and herein lies the advantage of the producers who operate a number of mines at the same time. As the grade of the ore from one of the properties falls off, a little high-grade ore from another property can be mixed with it and the average maintained, while if one property alone were being operated all of the ore below grade would be left behind. This mixing operation, however, can continue only as long as there is high-grade ore available for mixing with the high-silica ores and, while the tonnage of iron ore in the Mesabi Range is still enormous, the tonnage of high-grade ore suitable for mixing with any quantity of low-grade ore is being rapidly depleted. Obviously, if an 18 per cent. silica ore can be reduced by concentration methods to 12 per cent. silica, considerably more of it can be utilized with a given amount of high-grade ore. The operators on the Mesabi Range recognize this situation and are energeticdly endeavoring to reduce the silica in their concentration plants because every unit of silica that can be removed by concentration is a conservation of their high-grade ores. More Elaborate Processes Will Be Needed At the present time there are thirty-seven concentrating plants on the Mesabi Range, and about one-third of the total ore shipped is beneficiated in these plants. In about one-half of these plants no reduction is made in the silica but the moisture or structure of the ore is improved. The washing process is by far the most important method for the removal of silica, and it is interesting to observe that the tonnage of "wash" ore during the past five years has shown practically no increase although the total tonnage of ore shipped has increased. This is due to the fact that the available tonnage of wash ore is being depleted and the amount

Jan 1, 1930

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By Frank Alfred Fahrenwald

MetallURgical research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been , found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likeiy that a material can be produced which, will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series1 has shown that alloys of those metals maybe produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties—including the ease with which it may be soldered—are invaluable. But it is most extensively used in

Jan 1, 1916

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By W. N. Lacey, R. H. Dourson, B. H. Sage

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950