Search Documents

By George Otis Smith

A YEAR ago, ,at the Institute's dinner, I closed my A remarks with the words: "The scientist devotes his life to the advancement of learning; the engineer gives his to the advancement of living." May 1 begin tonight where I left off then and speak first of the distinction between science and engineering? This difference is a difference both in purpose and in method: it is the sharp contrast between theory and practice; it marks the broad gap between dream and attainment. Sometimes it happens that the investigator is also the builder and applies what he discovers, yet the distinction between science and engineering serves to point out the broad dependence of the engineer upon his brother the scientist. You remember .the old - saying that "where there is no vision the people perish" translate this into modern experience and we may say that "where there is no science, the engineer fails."

Jan 1, 1929

By O. G. Lellep

IN every country economic circumstances prescribe the method used to produce a commodity at lowest cost. In Pennsylvania a man's wages for working 4 hr buys a ton of coal wholesale; in Germany a laborer must work 40 hr, or ten times as long. In western Europe, therefore, conservation of fuel is of primary importance, and recent practices of burning lime and cement differ from those employed in the United States. This paper presents data collected during a trip through western Europe in 1953. Considered uneconomical, shaft kilns for burning cement disappeared in the United States two generations ago. But because required capital investment is low and operation greatly improved, shaft kilns are still used to some extent in Europe, where fuel costs are high, and are even included in designs for plants under construction. During the last 50 years shaft kilns have been maintained at the same physical size, while their output has been increased at least four times.

Jan 7, 1954

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By Earle E. Schumacher, Alexander G. Souden

IN the field of physical metallurgy it is becoming increasingly difficult to keep abreast of the recent develop¬ments since the diversity of investigations is so great and the literature so voluminous. The purpose of this review is to present the more important advances in the nonferrous field during the past few years, the topics discussed being classified broadly as fundamental and practical. The former includes those studies that have done most toward developing the basic science of metals and alloys, and the latter includes technical developments and applications. With the rapid growth of the metal

Jan 1, 1938

By C. S. Anderson

Georgia, since 1829, has produced nearly $18,000,000 from her gold mines, but in late years the output has dwindled to insignificance. In view of present universal efforts to increase gold production, it seems pertinent to record some recent observations in that field, briefly review its past and weigh probabilities of reviving gold mining there. Little in this paper can be claimed as new or original, and it does not present results of a detailed or profound investigation of the whole region. The Allatoona gold mine was reopened in January, 1932, and explored at greater depth during the period from January to June of that year. A number of other abandoned mines were visited, but since the workings, in common with most such mines in Georgia, were flooded or caved, underground conditions could not be examined. For a wider knowledge of the subject, a search was made through available pertinent literature and statistics, a bibliography of which is appended hereto. To all the sources obligations are gratefully acknowledged. Production The discovery of gold in Georgia, in 1829, led to an influx of 6000 to 7000 miners and a production of over $200,000 in the following year. A branch of the United States Mint, established at Dahlonega in 1838, accounted for $6,115,569 up to the time of the Civil War. The output fluctuated greatly from year to year, with an all-time peak of $582,782 in 1843. In only one other year, 1845, was the half million mark exceeded. After the war mining began again, but 1883 is the last year for which an output of $200,000 is reported. Placers, always the main source of production, were yielding less and less, and in spite of increased quartz-mining activities the downward trend continued. The last year in which there was a production of $100,000 was 1902. In 1914, $16,270 came from 26 placers and 11 deep mines, with the latter reporting 1750 tons of $3 average value. In 1925, one placer and four lode mines that mined 8100 tons assaying $1.19 per ton produced $9500. One placer and one quartz mine, operating in 1930, reported a total output of $4194. Table 1 pictures the waning output.

Jan 1, 1934

By Paul M. Tyler

DOES mining pay? Inasmuch as the whining of minerals from Nature is one of the world's principal sources of new wealth, this question is of general economic interest but it is obviously of even more vital concern to investors and those engaged in mining. In a previous article on "Wage Costs in the Mineral Industries,' published in the November issue, I attempted to show that wages paid workers on the job accounted for, roughly, 50 per cent of the mine dollar. Salaries normally range over 5 per cent - lower for large metal mines but higher in stone quarries and minor nonmetallic min. in, industries. Purchases of supplies, materials. fuel, and power generally aggregate within the range of 15 to 25 per cent of total receipts, with the average well under 20 per cent. The total of all such specified expenditures which may he loosely described as

Jan 1, 1934

By W. E. Gaby

INTRODUCTION SINCE the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,1 Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the "Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down.

Jan 9, 1916

By JAMES BRADLEY

THE Spanish mine is in Nevada County, California, 21 miles northeast of Nevada City by road, and 3 miles north of the town of Washington. The mill and surface buildings are on Poorman's Creek at an ele¬vation of 3,000 ft. About 35 men are employed at the property, which is producing 50 tons of ore per day. Electric power, purchased from the Pacific Gas and Electric Co., is brought in from Alleghany, seven miles away. In the early days the mine was operated by F. W. and P. R. Bradley. Between 1883 and 1899 the production was approximately $900,0)0 in gold. The ore treated during; that time yielded an average of 60 cents per ton and was mined and milled at a profit. The surface, oxidized, ore deposit was 30 to 100 ft. wide and was mined by the glory-hole method. The milling-plant at first consisted of a Blake crusher an-1 a small Huntington mill; later three large Huntington mills were added to the plant. In 1893 a new mill was built at a lower adit- It consisted of 10 stamps and four Huntington mills. The gold was secured by amalgamation, the recovery being about 50 per rent.

Jan 1, 1931

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By AIME AIME

Annual net production of crude oil from the Anglo-Iranian, Oil Company's fields in Iran for the years 1940 through 1945 amounted to: YEAR TOTAL PRODUCTION (Long Tons) 1940 8,626,639 1941 6,605,320 1942 9,399,231 1943 9,705,769 1944 13,274,243 1945 16,835,000 (preliminary figure) All developed fields were on almost continuous production throughout the war, though their operation naturally was hampered by war conditions, which affected particularly supplies of equipment.

Jan 1, 1946

By Yasushi Ishikawa

The fact that the degree of granulation and the state of granulated particles of sinter raw mixtures are the influential factors in ensuring coke combustibility and permeability during sintering has been clarified. Based on this knowledge, Nippon Steel developed the divided coke-addition process and the technology to utilize binder, and applied them on a commercial scale. Productivity and sinter quality are thereby greatly improved with a significant reduction in fuel consumption.

Jan 1, 1977

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. ' The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

[Separates of all the Technical Publications published in 1929 are available at lnstitute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions.] Metal Mining Technical Pdbli- Title Author Meeting Trans. cation . Volume No. and Page* 182-A-23 The Royal Commission on Mining Henry Louis New York Subsidence Feb., 1929 183-A-24 Cycles in Metal Production D. F. Hewett Nen. York T29, 65, 95 Feb., 1929 199-A-25 Ventilation at the United Verde Oscar A. Glaeser New York T29,- 114. Mine Feb., 1929 206-A-26 Air Conditioning In Deep Mines R. W. Waterfill New York T29. 99, 112 Feb., 1929 245-A-27 Bumps in No. 2 Mine, Springhill, Walter Herd New York Nova Scotia (with discussion) Feb., 1929 257-A-28 Misfires: Their Causes, Prevention New York and Treatment on Occurrence Feb., 1929 Misfires in Anthracite Coa1 T. D. Thomas Mines (With Discussion) Misfires in Bituminous Coal W. H. Forbes Mines (With Discussion) Misfires in Non-metallic Mining A. W. Worthington (Limestone) (With Discussion) Milling and Concentration 195-B-15 A Study of Differential Flotation C. R. Ince New York Feb., 1929 196-B-16 Elements of Operation of the Arthur F. Taggart New York Pneumatic Table H. L. Lechmereoertel Feb., 1929 202-B-18 Silver-bearing Minerals of Some A; W. Habn New York T29, 325 Ores from Tintic Mining District Feb., 1929 204-B-17 Experiments with Flotation Re- A. F. Taggart New York agents T. C. Taylor Feb., 1929 C. R. Ince 208-B-20 Cyanide Regeneration or Recov- C. W. Lawr Sun Francisco ety as Practiced by the Com- Oct., 1929 pania Beneficiadora de Pachuca, Mexico 214-B-19 Calculations in Ore Dressing W. Luyken New York E. Bierbraer Feb., 1929 217-B-21 Differential Grinding Applied to Leon M. Banks San Francisco Tailing Retreatment George A. Johnson Oct., 1929 224-B-22 Reducing and Oxidizing Agents Research Staff San Francisco and Lime Consumption in Flo- of United Verde Oct., 1929 tation Pulp Copper Co. 247-B-23 Copper Sulfate as Flotation Acti- 0. C. Ralaton San Francisco vator for Sphalerite 0. R. King Oct., 1929 F. X. Tartaron

Jan 1, 1929

Sponsored by the Utah Section of AIME, the 1960 Annual Rocky Mountain Minerals Conference brought more than 500 members of the mineral industry to the conference rooms of the Newhouse Hotel in Salt Lake City during the period October 5 to October 7. Under the overall supervision of J. M. Ehrhorn, general chairman, and H. E. Wright, assistant general chairman, the Conference offered 14 papers of technical interest in four sessions during the first two days, and it culminated in the Exploration Symposium held on the morning of October 7. The opening session of the Conference, meeting on the morning of October 5, heard R. P. Work, utility engineer of the Mountain Fuel Supply Co., discuss the growth and economic factors related to the use of natural gas in Utah. In his paper entitled Natural Gas Market In Utah, Mr. Work emphasized the very good prospects of natural gas serving almost all parts of that state. He mentioned that recently the El Paso pipeline, built to serve the Pacific Northwest with gas from Texas, has permitted natural gas to be available to Eastern Utah, and a tentatively planned pipeline from Green River, Wyo. to Southern California will bring natural gas to the central and southeast areas of the state.

Jan 11, 1960

By CHARLES M. A. STINE

IN fighting a war the all-absorbing intent is to win. There is little time to analyze the rush of events or to appraise their consequences beyond the war's end. The united objective is, rightly, success for our arms. Yet under the pressures of a great war there may be compressed scientific, economic and social developments that might have taken many decades to achieve under less urgent conditions. Their effects on our lives and all civilization may be more wide-reaching and lasting than any military conquest. They constitute one of the must imperative incentives to victory. No American, least of all any scientist worthy the name, conceivably could endorse war as a justifiable means to progress. The destruction of life and property wrought by the present war far exceeds the havocs of a century's earthquakes. Most of mankind is burning itself on an altar of paganism. Nonetheless, one fact is inescapable Despite the recurrent malady of war history's overall course is forward. Mankind has the habit of rising phoenix-like from its own ashes to attain greater heights. Progress is immortal.

Jan 1, 1942

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By Millard K. Shaler, Sydney H. Ball

During the past 50 years the attention of mining-men has been turned to Africa, and within the past decade prospecting-expeditions sent into Central Africa have resulted in the open-ing-up of several mines. Having recently spent two years in the Belgian Congo for the Societe Internationale Forestiere et Miniere du Congo, it is our purpose to outline briefly the mining-conditions in that part of Central Africa. Before it became, in 1908, a Belgian colony, this region was known as the Congo Free State. 11. Location and Area. The Belgian Congo lies in southwestern Central Africa, west of the continental divide, as illustrated in Fig. 1. It has a coastline of but 20 miles on the Atlantic, but widens rapidly eastward to points 5 north and 14 south of the equator. Its area is 908,000 sq. miles, which is almost one-quarter that of the United States and Alaska, or more than one and one-half times that of Alaska. Stated in other terms, its area is nearly one-third that of the United States, exclusive of Alaska and the insular possessions, or more than that of all the United States east of the Mississippi river. III. Topography and Drainage. From north to south, Africa is made up of three topographic elements: 1, the Atlas mountains, a highly-accentuated region

Jan 1, 1911

By Thomas T. Read

Jan 1, 1913

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920's, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930's, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940's were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960