Search Documents

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before break-age, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 8, 1950

By Walter R. Hibbard

ALTHOUGH extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110), [III] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampon5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr s in a standard mercurous nitrate test. Edmunds 12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wassermann reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. PREPARATION OF SPECIMENS Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5,10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. DETERMINATION OF POLE FIGURES A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pct nitric acid to 0.0015 in. thickness and (III) pole figures were determined using copper K-alpha radiation in the manner described by Brick.1 The three general types of pole figures

Jan 1, 1947

By J. Marshall Rounsevell

It is probably not too far from the truth to say that the sulfur content of the steel bath at the first turndown of the basic oxygen furnace is influenced by every factor which varies in the operation of a BOF shop. However, the determination from normal shop operating data of the effect of a given factor on turndown sulfur content requires a means for collecting a large quantity of such data and a significant variation of the factor in question in that data. In this paper, operating data from 4000 heats collected on the computer at Inland's No. 4 BOF Shop is utilized to analyze the effect of four operating parameters -- hot metal sulfur content, hot metal manganese content, percent burnt dolomitic lime (dolomite) in the flux charge, and the presence or absence of transfer ladle slag skimming -- on first turndown sulfur content.

Jan 1, 1972

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967

By J. L. Martin, W. M. Campbell

A new electric logging method, called displacement logging, often gives a direct indication of the presence of mobile hydrocarbons in hydrocarbon-bearing formations. This method is based on the detection of a bank of connate water which is formed between the invading mud filtrate and virgin formation fluids in these cases. The existence of this phenomenon has beer, verified by laboratory studies and by actual field logs taken in known oil sands. INTRODUCTION During the past decade increasing use has been made of conventional electric logs to determine the amount of oil or gas in formations traversed by a borehole. This determination requires knowledge of several factors, such as true resistivity of the formation, formation factor, and water resistivity. Sometimes all of the factors necessary to make a reliable saturation calculation are not available. Also, the computations and corrections which are necessary in such a study often require the services of an experienced log analyst. It has long been the desire of exploration people to have a logging device which will locate hydrocarbon-bearing formations directly without requiring complex interpretation methods. The displacement log, while not completely fulfilling this desire, appears to be a Step in that direction. Basis for the Device The basis for this device stems from a phenomenon which occurs when mud filtrate invades a formation which contains displaceable hydrocarbons. As the mud filtrate invades the formation, most of the oil or gas is pushed out of the invaded zone, leaving residual oil. However, in addition to displacing most of the oil or gas, the connate water is also swept out, since the originally irreducible water is mobile in the presence of a water phase.1,2,3 Tonsequently, this irreducible water piles up as a bank between the virgin oil zone and the invading filtrate. If the mud filtrate is of higher resistivity than the formation water— as is commonly the case—the resulting annular zone, containing the bank of formation water, will be of lower resistivity than either the virgin oil-bearing formation resistivity or the invaded zone resistivity. This resistivity configuration, going from high to low to high again as the distance from the borehole increases, is found only in those zones which contain displaceable hydrocarbons. A device which would reliably detect this low resistivity zone would give a direct indication of mobile hydrocarbons. Illustrations This phenomenon is illustrated in Fig. 1 and 2. Fig. 1 shows a sketch of a zone containing salty connate water plus displaceable hydrocarbons, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 2 shows this zone, together with fluid content and resistivity graphs. after invasion by a fresh water mud. The resistivity pattern on moving away from the borehole is high: low: high. The absence of the low zone phenomenon in water zones is illustrated in Fig. 3 and 4. Fig. 3 shows a sketch of a zone containing salty formation water and residual oil, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 4 shows this water zone, together with fluid content and resistivity graphs, after invasion bv a fresh water mud. In this case the resistivity pattern on moving away from the borehole is high: low since there is no change in water saturation at the head ol

Jan 1, 1956

By W. B. Agocs

In August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model I1 total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey.

Nov 1, 1955

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

By Y. A. Topkaya

The placer gold occurrences at Sart Çayl, Manisa, Turkey, the legendary River Pactolus of King Croessus, were evaluated in this study to determine if this deposit contains sufficient recoverable value to justify development and exploitation. The gold occurs both in the upper Neogene conglomerates and the alluvium derived from these conglomerates. The total reserve in the whole region is estimated to be 500 million cubic metres. Samples were taken of the upper conglomerate and in the alluvium in an attempt to determine the amount and the physical nature of the gold. The gold in samples was recovered by screening out barren oversize followed by washing the sand and gravel through riffled sluices. The resulting sluice concentrate was later panned and amalgamated at site. Laboratory cyanidation testing of some samples for control purposes was also done. The average calculated free gold was found to be about 90-100mg/m3 and the size of gold flakes found was quite small. The field as well as laboratory testing of the samples of Sart Çay1 indicated that the potential reserves in this region could only be developed as a sand and gravel operation and the gold could be recovered together with the heavy minerals as a byproduct.

Jan 1, 1984

By T. C. Atchison, W. I. Duvall

Over the past ten years a series of investigations have been conducted to determine some of the pnysical processes involved in breaking rock with confined concentrated charges. Detailed discussions of many of these investigations have been published elsewhere.1-6 Laboratory experiments made by other investigators using Hopkinson pressure-bar techniques have shown that solid materials are fractured in tension by the reflection of an incident compressive stress pulse at a free surface.7-12 In these tests a small charge of explosive is placed in contact with one end of a bar. Detonation produces some plastic flow and crushing of the bar near the charge and generates a compressive stress pulse that travels along the length of the bar. At the free end of the bar the compressive stress pulse is reflected back into the bar as a tensile stress pulse. If the tensile strength of the bar is exceeded during this reflection process, a tensile fracture normal to the length of the bar is produced, and the broken end of the bar moves forward with a constant velocity equal to the average particle velocity trapped in the broken fragment. The new surface formed by the fracture becomes the new free end of the bar that reflects the remaining portion of the incident compressive stress pulse. This process is repeated any number of times until all of the incident stress pulse is reflected. Hino has demonstrated this kind of breakage for three rock types—marble, granite, and sandstone." He has defined a blastibility coefficient, B, as the ratio of compressive strength, C, to tensile strength, T, thus: C The quantity B is the maximum number of slabs that can be produced by reflection breakage. Normally fewer slabs are produced because of loss of energy as the stress pulse travels through the rock. Fig. 1 illustrates reflection-type fracture for a triangular compressive stress pulse. The number of slabs produced by the reflection breakage process is the first whole number less than the ratio of the peak stress of the incident pulse to the tensile breaking stress of the solid. Thus the number of slabs is given by the thickness of each slab is given by and the total length of rock broken is given by N = number of slabs S - peak stress in incident pulse T = tensile strength of the rock F = fall length of incident stress pulse h = thickness of each slab D = total length of rock broken During the reflection process the particle velocity at the free surface is twice the particle velocity in the incident stress pulse. Thus the velocity with which the broken fragments move forward is given by where v, = velocity of broken fragment, and v = average particle velocity contained in that portion of the incident pulse trapped in the broken fragment. Results of these laboratory experiments cannot be applied directly to rock blasting where the explosive charge is placed in a drillhole. In laboratory tests the charge is unconfined and in contact with the rock in only one direction. In a drillhole additional confinement is offered by the rock surrounding the charge and by the stemming placed above it. This additional confinement may be enough to allow the explosive gases to do additional work on the rock during their expansion. Other writers have discussed possible effects of gas expansion'on rock breakage.13-10 However, very few experimental data are available to determine to what extent expansion of the gases is responsible for rock fragmentation. The USBM has studied the physical processes involved in breaking rock with confined concentrated charges by using simple crater tests breaking to one free surface. Crater tests have been performed in four rock types: granite, sandstone, marlstone, and chalk. Table I gives some physical properties of these rocks. Fig. 2 shows plan and section drawings of two typical crater tests and illustrates some of the test variables measured. For these tests the charge was placed at the bottom of the drillhole and primed with an electric cap. The hole was stemmed to the collar with sand and the charge detonated. Size and shape of the crater were measured after it was cleared of broken rock. As a given charge size was buried deeper in a drillhole, the crater depth usually was equal to or

Jan 1, 1960

By W. C. Elmore

THE magnetic powder method, long used for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations-of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1935

LOCAL SECTIONS (There are 60 Local Sections in the United States, 4 Foreign ) ADIRONDACK Established June 18, 1952 Paul W Allen, Chairman William Webb, Vice-Chairman Edwin Briggs, Secretary-Treasurer National Lead Company Mac Intyre Development Tahawus, New York Paul W Allen, Section Delegate R G Fleck, Alternate Section Delegate

Jan 1, 1954

By W. C. Elmore

THE magnetic powder method, long used for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By M. J. Greaves, Alan English

Pelletizing on a commercial scale is only 10 years old; yet in this period more than 150 million tons of pellets have been produced. Instrumentation and controls have played an important part in the development of an entirely new industry in almost unprecedented time. Initially, most control circuits used in the pelletizing industry were manually operated, since the confidence factor in instruments and controls was quite low at that time. This changed considerably in recent years and improvements in the use of instruments and controls have probably developed more rapidly in pelletizing than in any other metallurgical process. Now, within a decade of the start of commercial operations, the use of manually operated controls has changed and consideration is being given to the utilization of computers for data logging and control purposes.

Jan 7, 1965

Energy conservation has been the keyword in many plant expansions. Far many years, most of the phosphate industry has been dry grinding their phosphate rock. Agrico Chemical in Florida has recently been evaluating the wet grinding of phosphate rock, a process which eliminates a pre-dry stage for mill feed while allowing higher through- puts. This same company also plans to open a new phosphate facility in Louisiana that will use wet grinding in both ball mills. The Eveleth Expansion Co.'s Fairlane concentrator will have the largest rod and ball mills in the US mining industry. The plant will consist of three lines, each with one rod mill and one ball mill, and will process 464 ltph. The rod mills will be 15 x 20% ft, drawing 2035 hp. The ball mills will be 17 x 41½ ft, drawing 6900 hp and driven by dual 3000- hp motors. The plant is scheduled for startup in the fall of 1976.

Jan 2, 1975

By W. C. Elmore

THE magnetic powder method, long used. for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickels single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By F. M. F. Cazin

Some twenty years ago the author of a book,* by which, for the first time, molecular action was made to account for nearly all phenomena in hydrodynamics, began his preface as follows: " It is contrary to all experience, that any branch of science should suddenly cut short its own line of reasoning, and drop all connection with its past, and yet as quickly re-establish itself on an entirely new basis. It is, therefore, not without justification that this book should be met with caution and even distrust." When the newly-discovered natural facts and laws presented in this paper were, in 1891, first laid before the officers of the American Institute of Mining Engineers, they might have been preceded by a preface to the same effect; and the expression would have found its justification by the actual experience these facts and laws met with. Since then, as the result of their publication in one of the most prominent

Jan 1, 1895

By D. V. Fites

Criteria for deciding when rock should be ripped and what ripping equipment and techniques should be used in given situations are discussed in this article. The relation between ripper performance and seismic wave velocities in various types of rock is also discussed. The ripper is not a new tool. In fact, it dates back as far as the Roman Empire. The Roman's ripper-mounted on wheels and shaped something like a plow — was pulled by oxen and used to loosen the earth for the shovelers and basket carriers building the Appian Way. There are records of rippers being used in this country in railroad construction between 1860 and 1880. However, the ripper as we know it today did not appear until about 1930. Tractor-drawn models were in use in 1931 on the Hoover Dam project. At that time they weighed about 7500 lb and were pulled by tractors with about 75 flywheel hp and up to 30,000 Ib total weight. The chief shortcomings of trailed

Jan 1, 1969

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or. other persons.) Position for a single man experienced in cyanide mill construction and operation at a small mine in Nicaragua. Salary $150 per month and expenses. No.. 39. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, desires position in ore dressing, either experimental or operating. Has had practical experience in flotation and other special methods. No. 228. Member, technical. graduate, 10 years' experience in Belgian coal mines, five years' experience in American coal mines in connection with reorganization of companies and opening of new coal fields. Aged 37. Speaks Spanish. No. 229

Jan 7, 1915

By John F. Abel

At the spring meeting of the Open Pit Division of AIME's Arizona Section, I was asked a question which indicates the acceleration of technical advancement. The question was: "How does an engineer at a properly keep abreast of what is new?" The fact that some 200 Arizona AIME members were at the meeting is a testimonial to the desire of these men to do just that- keep abreast. There is a great deal of talk in academic circles about the built-in obsolescence of an engineering or scientific education, too. About 100 commencement speakers every spring are sure to admonish the graduates that education is a continuing thing. Mining engineers are a small fraternity. We keep informed by talking to one another. Talking shop is valuable but there is no substitute for reading.

Jan 1, 1970