Search Documents

By H. E. Cline, T. H. Alden

A study zvas made of rate-sensitive plastic deformation and superplasticity in alloys of lead and tin. These alloys (lead, PO-19 pct Sn, Sn-38 pct Pb, Sn-2 pct Pb, tin) were extruded, aged at room temperature, or melted and resolidified to produce a variety of ~nicrostrnctures. Flow stress us strain rate data were obtained frorn tension tests for strain rates between 10-6 and 1 min-1. The curve log o .us log £ was S-shaped jor fine-grained materials and approxinzately linear for coarse-grained nzaterials. At constant grain size, the behavior was relatively insensitive to conposition. High rate sensitivity (d log o/d log k) and superplasticity occurred at intermediate strain rates in fine-grained materials and are believed to be associated with a transition with strain rate in the mode of plastic flow. This transition was shifted to higher strain rates with increasing temperataire or decrensing grain size. The high rate rneclzanisrn is presunzed to be slip, while rnetallographic evidence sug-gests that the low rate lnechanism is pain boundary sliding. PEARSON' discovered that extruded eutectic alloys of Pb-Sn and Bi-Sn could be elongated as much as 2000 pct in tension. The ability for stretching decreased with aging time or annealing to increase the grain size. At high strain rates, or if the material was in the cast condition, normal ductility was observed. Following deformation of the extruded Pb-Sn eutectic at low rates, Pearson observed an equiaxed granular structure on an initially flat surface, while rapid straining produced elongated grains. He attributed the large deformation in the extruded alloys to the persistence of extremely small grains to a temperature sufficiently high for inter granular flow. Avery and backofen2 measured the strain rate sensitivity of the flow stress, m = d In old In 6, in the Pb-Sn eutectic and established a correlation between m and the tensile elongation. In the extruded eutectic alloy the strain rate sensitivity was 0.1 to 0.2 at rapid rates and the elongation was small, while at low rates m increased to 0.4 to 0.6 and superplastic elongation was observed. They also noted a grain size effect. In the case of the cast Pb-Sn eutectic the strain rate sensitivity remained at 0.1 over the range of strain rates of their experiment (3 x 10"3 to 2 min-I). These authors suggested that diffusional (Nabarro-Herring) creep was the mechanism by which deformation occurred at low strain rates, while climb-controlled creep occurred at high rates. Two predictions of this model are that, at low strain rates, the strain rate sensitivity approaches 1, i.e., Newtonian viscosity, and that the strain rate at constant stress varies as D/L2, where D is the coefficient of self-diffusion and L the grain size. More recently, a mechanical and microstructural investigation of the dilute superplastic alloy, Sn-5 pct Bi, has been done.3 The results show that the high strain rate sensitivity is associated with a transition with strain rate of the mechanism of plastic flow. At low strain rates, grain boundary sliding and its associated accommodation processes were evident, while at high strain rates quasi-uniform slip was concluded to be the dominant deformation process. The following experiments were performed to extend our knowledge of the phenomena of superplasticity to a larger range of strain rates, compositions, temperatures, and microstructures in the Pb-Sn alloy system. The question of why a cast structure does not exhibit viscous behavior although it appears to have a fine microstructure2 was investigated.

Jan 1, 1968

R. W. NEWCOMB,* New York, N. Y. (written discussiont).-On page 1638 mention is made of a new -instrument with an exceptionally high resistance that has been developed by Charles Engelhard. All friction and wear of moving parts of the moving system has been elimi-nated by replacing the hardened steel pivots and jeweled bearings, commonly used on other instruments, by a double metallic filament, one at the top and One at the bottom, under slight tension. Any pos-sible distortion of the moving coil, because of tension, has been eliminated by introducing a solid spindle as the axis of the coil between the points on the coil where the metallic filament is attached. The filaments serve not only as a support for the moving coil; but also to lead in the current from the binding posts to the moving coil, and as a source of counter-torque; instruments so constructed, do not require leveling, and are mechanically very robust. The clock of the recorder serves only to drive the chart at its specified rate and -to operate a small contact-making device; i.e., there is no other mechanical load on the clockworks. The contact-making de-vice is so constructed that there is a quick-make, a quick-break, and a wiping effect while the contact is being made. Contact surfaces on this switch are of platinum platinum-iridium. The operation of this contact, which occurs once each minute, sends a current, from a 6-volt supply; through a solenoid magnet, which operates the depressor bar mechanism in the case of the single-record instrument; in the case of the multiple-record instrument, it operates the automatic switch and color-changing features, as well as the depressor bar.

Jan 12, 1919

By George W. Maynard Maynard

IN this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporary suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our own Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in September, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith's fire, metallic iron is formed, which, on being heated to the welding-point on the same smith's hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxing materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slag." This is the keynote of the Siemens direct process. Dr. Siemens says further: "If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, and the fusion of the earthy matter .mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, we shall find that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonaceous matter per ton of iron contained in the' ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By G. W. Maynard

In this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporay suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our owu Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in september, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith's fire, metallic iron is formed, which, on being heated to the welding-point on the same smith's hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxiug materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slog." This is the keynote of the Siemens direct process. Dr. Siemens says further: " If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, arid the fusion of the earthy matter mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, weshall rind that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonsceous matter per ton of iron contained in the ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By Jacob Reeese

I HAVE discovered a new method by which steel and other metals may be burnished by the automatic action of the burnishing machine, and by which the cost is greatly diminished, and more perfect work produced. And in addition to the polishing and burnishing action of

Jan 1, 1881

By Jacob Reese

I have discovered a new method by which steel and other metals may be burnished by the automatic action of the burnishing machine, and by which the cost is greatly diminished, and more perfect work produced. And in addition to the polishing and burnishing action of

Jan 1, 1881

By R. S. Busk

Niels Engel (University of Alabama, University, Ala.)— In this paper it was pointed out that the electron-gas and energy-band theory accounts for the fact that the lattice parameters exhibit a sudden change when the electron concentration (number of bonding electrons per atom) exceeds a certain number around two. This statement is said to support and prove the electron-gas theory. But this theory is not able to account for a series of experimental data. Also several expectations, deduced from this theory, are not found to exist. In Figs. 6 and 7 the energy bands of the second and third periods are given as they must be assumed in order to account for the electrical properties of the elements in these periods. In Figs. 6 and 7 the electron-gas and energy-band theory is compared with the electron-oscillator hypothesis in accounting for the properties of the elements in the second and third periods. Fig. 6 shows the second period, The energy-bands are overlapping and separated to be in agreement with the electrical conductivity of the elements. The oscillator hypothesis explains conductivity due to electron vacancies. In graphite there is a closed s-shell in every other atom and two vacancies in the others. Conductivity is therefore only maintained by migration of s-electrons in graphite. In boron there are no s-electrons. The diatomic molecules of nitrogen and oxygen and the paramagnetism of oxygen can be accounted for by a similar behavior as the s-electrons of the bonding electrons. But this explanation will deviate too much for the purpose of this discussion. Fig. 7 shows the third period. In the energy-band picture about two s-electrons are assumed in magnesium and aluminum, but only one s-electron is assumed in silicon. The diamond lattice is assumed to be controlled by a sp3 hybrid. However the electron distribution develops ideally according to the oscillator hypothesis. Only sodium, magnesium, and aluminum exhibit electron vacancies and conductivity. To account for the insulator properties in Si, P, and S in the third period it must be assumed that the four last added p-electrons must be taken up in bands containing only one electron per band.' (Compare the electron band picture in Hume-Rothery.' Hume-Rothery does not consider the insulator properties of the nonmetals.) In the second period already the first p-electron must have entered a single electron band. Based on the energy-band picture in Figs. 6 and 7, the following questions must be asked: 1—Is it consistent with the energy-band idea that electrons of the same kind (p-electrons) can be divided into separated bands? 2—Is it consistent with the energy band idea that single electron bands can exist? 3—Why are the first two p-electrons (in boron and diamond) separated into two single electron bands in the second period, but overlapping in the third period (aluminum)? 4—Why are s-electrons and d-electrons taken up in continuous overlapping bands, while p-electrons are divided into single electron bands? 5—Why do the peaks and valleys (y and w and further x and z) of the energy band below four electrons per atom not show up in the electrical conductivity of alloys? For example consider the Li-Mg system or the alloys between Mg and three electron metals where the mentioned discontinuity in the lattice parameter is found. 6—Why does the beginning of the p-electron band (x) not show up in the lattice constants similar to the filling up of the s-electron band (z) ? In magnesium alloys the electron-gas theory postulates the first Brillouin zone to be filled at about two electrons per atom. This is claimed to explain the sudden change in lattice spacing and c/a values of several magnesium alloys when the electron concentration exceeds a few percentage points over two electrans per atom. This was emphasized in the paper by Busk. If the electron-gas energy-band theory is correct a sudden change in electrical conductivity and possibly other properties .should be expected when the same electron-concentration or temperature is exceeded. A sudden change in lattice spacing or other properties should also be expected when the filling degree is such that p-electrons are introduced into the p-band, for example at x in Figs. 6 and 7. Such phenomena are at found by experiment. and If the number of electrons should vary with the energy level depending on the average number of bonding electrons per atom, the electrical conductivity should be expected to vary in accordance with the energy band layout (Figs. 6 and 7) caused by different numbers of conducting electrons at different filling up degrees. Nothing indicating such a behavior is observed. In addition to these discrepancies between the electron-gas and energy-band theory and measured data, the theory violates the principles developed along with the Bohr theory of atomic structure. According to these principles a filled shell is saturated and therefore unable to form bonds. Therefore two S-electrons per atom should form a closed or saturated shell, which has been pointed out as accounting for the inability of helium to form bonds. Beryllium, magnesium, or calcium atoms with two s-electrons should be expected to form inert atoms with properties almost like the helium atoms. Several other inconsistencies and disagreements with measured data of the energy-band theory can be mentioned. Some of these are discussed with reference to other papers. 8 Because the electron-gas and energy-band theory seems to fail on several points, I have developed another theory which can account for all the phenomena the electron-gas theory is able to account for. This new theory is further able to account for things which are impossible to explain by the electron-gas theory at the present state.

Jan 1, 1953

By W. S. Hyler, W. L. Bruckart

The powder metallurgy and arc-cast types of wrought molybdenum stock were studied in rotating beam fatigue. Endurance ratios of unnotched specimens after 5x10 cycles were found to be 0.74 and 0.81, respectively. Fatigue notch factors (K,) of 1.36 and 2.05, respectively, were obtained on V-notched specimens having a theoretical stress-concentration factor Kt = 3.1. MOLYBDENUM and its alloys are rapidly gaining importance as engineering materials of construction for high temperature applications. AS a wrought material, molybdenum and its alloys are outstanding above 1800°F. It is necessary, however, with molybdenum to provide elevated temperature oxidation protection. This is currently being studied by a number of investigators. Thus far, there have been no published data on the fatigue behavior of molybdenum either at room temperature or at elevated temperature. The knowledge of fatigue behavior, particularly notched fatigue behavior, becomes increasingly important as the engineering importance of a material increases, especially from the design standpoint. The work described here was directed toward determination of the notched and unnotched rotating beam fatigue characteristics of molybdenum at room temperature. Also, it was desired to learn whether any difference exists between wrought molybdenum of the powder metallurgy and the are-cast types. Fabrication History of Bar Stock For this work, bar stock was procured from Climax Molybdenum Co. (are-cast type) and from Westing-house Electric Corp. (powder metallurgy type). The processing histories of these materials are listed in Table I. The first lot of are-cast molybdenum was deoxidized by aluminum additions. The second lot was deoxidized by carbon." Both lots of the powder Microstructure A microscopic examination of these materials, as received, revealed the powder metallurgy molybdenum to be free of inclusions and to be finely fibered. On the other hand, the are-cast C molybdenum possessed numerous carbide inclusions, and the arc-cast A appeared to have coarse grained fibers. These are shown in Fig. 1. Owing to the large apparent difference in fineness of fiber between the are-cast A and the powder product and are-cast C, a check was made of the recrystallized grain sizes to determine whether these differences persisted. A series of recrystallization anneals revealed mixed grain sizes in both the are-cast A and the powder product. Variations in grain diameter of as much as 50 times were found after full recrystallization at 1200°C for 30 min. There was no distinction between the two. Arc-cast C was not checked. Room Temperature Mechanical Properties Prior to subjecting the materials to fatigue tests, room temperature mechanical properties were determined. These data, together with the tensil: strength of the notched bars, data,togetherare listed in Table tensil: There were no significant differences in the tensile strengths of the two types of molybdenum. However, the powder metallurgy material was generally more ductile and yielded at a somewhat lower stress than the arc-cast material. Tensile strengths of the notched specimens indicated a slightly greater notch strengthening effect in the are-cast C than in the powder product, lot 2. Room Temperature Fatigue Properties Sample Preparation: Specimens were prepared for use in R. R. Moore rotating beam fatigue machines. These specimens had a continuous radius test section with a minimum diameter of 0.260 in. The specimens were prepared by grinding to shape and polishing to produce a smooth unworked surface. Polishing consisted of rotating a disk in the continuous radius section on which were attached, successively, emery belts of 240, 400, and 600 grit. The specimens were slowly rotated during the operation. The belt speed was high, and rotation was such that polishing scratches were longitudinal. Unnotched Fatigue Properties: Unnotched fatigue data were obtained from a number of specimens of each of the four lots of molybdenum. The results of the tests are presented in Fig. 2. From this figure,

Jan 1, 1956

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

By Richard E. Goodman

Rock slope stability assumes different roles in decision making as a mining venture develops and, accordingly, geological investigations vary in thought and in deed according to the project stage. During exploration, stability questions bear on the decision whether or not to mine, because their resolution affects the cost of mining. During the mine lay-out stage, stability is a key factor in deciding how to mine. Finally, during mine operation, stability affects safety and operating costs, and therefore, pit productivity. Among the many considerations influencing stability, rock mass classification and geological environmental factors count heavily. The rock mass behavioral class depends upon the rock character and its degree of fracturation. The loads on the rock are derived from the environmental factors of initial state of stress and the water regime. Of course, stability is also tied to a host of non-geological factors such as the pit geometry, mining style, relative wealth, philosophy of mine operation, and accident history. METHODS OF STABILITY EVALUATION AND CORRESPONDING INVESTIGATORY TOOLS The purposes of the geological investigation are to identify and evaluate the geological factors influencing stability so that the vital questions can be analyzed. The tools selected for stability analysis reflect the stage of development of the mining scheme and therefore the geological investigations, which must furnish data for the analyses and must vary with the project stage. For exploration and mine planning, the methods of resolving stability questions must meet the need to evaluate numerous parameters in limited time; examples of such methods are stereographic projections (1, 2, 3) charted solutions(4) and simple physical models (5, 6). An investigation program that employs geological mapping tools and aids to mapping, such as geophysics, with relatively few rock tests, is in balance with these analytical methods. First data about the water regime are obtained from observed piezometric levels, and the initial state of stress is queried simply through geological inference and experience. In the layout stage more elaborate physical scale models (7) and perhaps finite element models (8, 9, 10, 11, 12), will be relevant to the design process and therefore much more detailed geological investigation is required. The scale of observation of both rock material and joints will be significantly enlarged and mechanical tests of rock and joint strength

Jan 1, 1972

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion?).-Mr. Requa's subject is one of great economic importance, yet relatively new, and he has been able to combine extensive practical experience with the talent of grasping the broad features of a problem that has many discordant details.

Jan 5, 1918

By H. W. Graham

The young metallurgist of today who thinks casually of the technical literature of the steel industry might conclude that little has been published concerning the Bessemer process. This conclusion is true as relating to the last decade or two, but there is a fairly voluminous Bessemer literature in the period of 1860 to 1910. Since that time, however, an entirely new level of metallurgical knowledge of steelmaking has been reached; and the present paper is simply an effort to look broadly from this new level and to bring the recorded history of the process up to date. It is an effort to appraise the acid Bessemer method of steelmaking in the light of today's technical knowledge thereof. In this paper matters of history will be dealt with only insofar as they contribute to an understanding of today's situation. Attention will be directed to the apparent causes of past developments in seeking to perceive the true direction of trends now in existence and effective as bearing upon future developments. The paper will discuss the economics of the Bessemer process, but only to the extent that will bear upon the metallurgist's understanding of his responsibility. The problem of the quality of Bessemer steel will be reviewed and examples will be given of the technical data upon which the reasoning of the paper is based. Matters of engineering design, mechanical maintenance, operation and metallurgical investigation will be surveyed. Comparisons will be made between the Bessemer and open-hearth processes for the sake of clear and ready understanding. Production First of all it is considered logical and informative to show how much Bessemer steel has been and is being produced, and the relation of that production to the tonllage made by the open-hearth process. Table 1 shows the tonnages made by the two processes in representative years. It is to be noted that these figures are in net tons of 2000, lb., whereas previous to 1940 the Institute figures were compiled in gross tons. id open-hearth production and steel going into castings are included, since separated data are not available for the early years of the period covered. The ratio shown in Table I is merely the Bessemer tonnage for a given year divided by the open-hearth tonnage of the same

Jan 1, 1941

By H. W. Graham

The young metallurgist of today who thinks casually of the technical literature of the steel industry might conclude that little has been published concerning the Bessemer process. This conclusion is true as relating to the last decade or two, but there is a fairly voluminous Bessemer literature in the period of 1860 to 1910. Since that time, however, an entirely new level of metallurgical knowledge of steelmaking has been reached; and the present paper is simply an effort to look broadly from this new level and to bring the recorded history of the process up to date. It is an effort to appraise the acid Bessemer method of steelmaking in the light of today's technical knowledge thereof. In this paper matters of history will be dealt with only insofar as they contribute to an understanding of today's situation. Attention will be directed to the apparent causes of past developments in seeking to perceive the true direction of trends now in existence and effective as bearing upon future developments. The paper will discuss the economics of the Bessemer process, but only to the extent that will bear upon the metallurgist's understanding of his responsibility. The problem of the quality of Bessemer steel will be reviewed and examples will be given of the technical data upon which the reasoning of the paper is based. Matters of engineering design, mechanical maintenance, operation and metallurgical investigation will be surveyed. Comparisons will be made between the Bessemer and open-hearth processes for the sake of clear and ready understanding. Production First of all it is considered logical and informative to show how much Bessemer steel has been and is being produced, and the relation of that production to the tonllage made by the open-hearth process. Table 1 shows the tonnages made by the two processes in representative years. It is to be noted that these figures are in net tons of 2000, lb., whereas previous to 1940 the Institute figures were compiled in gross tons. id open-hearth production and steel going into castings are included, since separated data are not available for the early years of the period covered. The ratio shown in Table I is merely the Bessemer tonnage for a given year divided by the open-hearth tonnage of the same

Jan 1, 1941

THE Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 W. 39th St. in New York.

Jan 1, 1946

By J. S. Miller

This paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Neaquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 it. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65" and 70". Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. I), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired. In the pillar-skipping method (Fig. 2), the middle breast of three is not driven through and is drawn empty while the outside and inside breasts are kept full. At the corners of the two pillars standing, batteries are put in and a skip of the two pillars started; the coal in the two pillars is blasted over into the empty breast. A small pillar is kept along the

Jan 1, 1925

By D. H. Newland

Certain observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U. S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.' The deposits of Canada are described by L. H. Cole. Several states, including Kansas, Oklahoma, Iowa, Michigan,and New York, have made special surveys of their gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago. Association of Gypsum and Anhydrite The two calcium sulfate compounds, gypsum (CaSO4.2H2O) and anhydrite (CaS04), are the more stable forms of a series which includes at least two other members, so-called half-hydrate (CaSO4.1/2H20) and soluble anhydrite (CaS04). Each of the latter readily takes up water to recrystallize as gypsum and consequently is incapable of existence under ordinary geological conditions; also each can be prepared from gypsum by the application of heat within certain temperatures, the process on which is based the manufacture of commercial plasters. If the temperature limitations are not observed, the result of the calcination process will be insoluble anhydrite which, compared with the soluble form, takes up water very slowly so as to be of no practical use, although actually it is soluble and in time is convertible into gypsum like the other forms.

Jan 1, 1922

By W. G. Woolnough

It is perhaps a little difficult for Americans fully to appreciate the slow progress in the search for oil in Australia. Conditions are so different from those in the United States that methods must also differ considerably. Australia possesses an area almost exactly equal to that of the United States, but has a population of less than 7,000,000, and this population is concentrated almost entirely around the eastern and southern coasts of the continent. There are, therefore, vast "empty spaces" entirely unpopulated or exceedingly sparsely populated. The emptiness is due not to any lack of energy or initiative on the part of Australians but to the arid and waterless character of much of the country's interior. Throughout the greater part of the area that is comparable with the Mississippi drainage area of the United States, there is not a single flowing stream, and over most of it the rainfall is less than 7 in. a year. This hinders exploration and geological survey, and also isolates from potential markets many of the regions that otherwise might be considered worth prospecting. Also, Australia consists of six independent and sovereign states. With the establishment in 1901 of the Commonwealth of Australia, the states retained complete control of lands and mineral rights. Each state has its own petroleum legislation, and the absence of a central controlling authority has tended to confusion and to the introduction of many complications in oil prospecting. There are three major "territories," administered by the Federal Government; namely, the Northern Territory, enclosed between the northern parts of Queensland and Western Australia, within Australia itself, and the Territories of Papua and New Guinea in the island of New Guinea. Land and mineral legislation in these territories is not uniform. Furthermore, during the late twenties there occurred an orgy of company flotation and indiscriminate drilling, wQch resulted in the discovery of some definite indications of oil in three of the states and two of the territories, but which failed to develop any producing oil field in the common acceptation of the term. Much money was squandered,

Jan 1, 1938

By Alec M. Crowell, Thomas D. Bailey

Although natural gas was first discovered in Northwest Arkansas in 1887, . near Fort Smith, Sebastian County, the literature contains very little information on the region, which is separated distinctly from the oil area of Southern Arkansas. For that reason this brief and concise report is a summary of developments from discovery to the present time. Northwest Arkansas produced 5,736,-ooo,ooo cu. ft. of natural gas during 1942, the trend of production having been generally upward over the past five years, as is shown in Fig. I. Since 1904 a reserve of 237 billion cubic feet of natural gas has been discovered in Northwest Arkansas, of which approximately 162 billion cubic feet have been expended, leaving a reserve of approximately 75 billion cubic feet available as of Jan. 1, 1943. A prolific new field discovered in Pope County Oct. 23, 1942, will add to the reserve of the region materially. Per well reserves, over-all, are unusually high because of the practice of multiple completion. As yet no commercial deposits of oil have been discovered in Northwest Arkansas. but the gas deposits have proved of immense value industrially, principally in the processing of zinc ore mined in the local area as well as that imported from distant states. With the war, new interest in the exploitation of the metallic ores of the region lends new significance to the gas reserves tabulated herein. Geological Discussion The region covered in this report comprises the Arkansas Valley from Pope County weslward to the Arkansas-Oklahoma state line as shown in Fig. 2. This valley is a westward trending structural trough with sharp-topped ridges and mesa-like mountains rising above the valley's undulating surface. It is bounded on the north by the Ozark Highlands and on the south by the Ouachita Mountains. The sedimentary beds of the Arkansas Valley are composed mainly of noniossil-iferous shales and sandstones. The rocks contain a high content of carbonaceous material and many coal beds are found in the region. The Gxed carbon ratios (ratio of fixed carbon to volatile combustible matter of surface coals) are very high and average about 80 per cent over the region covered in this report. Little or no calcareous material is present. Rocks of the Arkansas Valley are sharply folded, and igneous intrusive rocks cut the sedimentary beds at a few places. The Arkansas Geological Survey' made a detailed reconnaissance survey of the Arkansas Valley province in 1927, the purpose being to delineate the major structural features (Fig. 3) and to point out the possibilities of discovering addi. tional gas deposits. More than fifty anticlines were mapped as a result of this survey. The information gained by this

Jan 1, 1943

By Thomas D. Bailey, Alec M. Crowell

Although natural gas was first discovered in Northwest Arkansas in 1887, . near Fort Smith, Sebastian County, the literature contains very little information on the region, which is separated distinctly from the oil area of Southern Arkansas. For that reason this brief and concise report is a summary of developments from discovery to the present time. Northwest Arkansas produced 5,736,-ooo,ooo cu. ft. of natural gas during 1942, the trend of production having been generally upward over the past five years, as is shown in Fig. I. Since 1904 a reserve of 237 billion cubic feet of natural gas has been discovered in Northwest Arkansas, of which approximately 162 billion cubic feet have been expended, leaving a reserve of approximately 75 billion cubic feet available as of Jan. 1, 1943. A prolific new field discovered in Pope County Oct. 23, 1942, will add to the reserve of the region materially. Per well reserves, over-all, are unusually high because of the practice of multiple completion. As yet no commercial deposits of oil have been discovered in Northwest Arkansas. but the gas deposits have proved of immense value industrially, principally in the processing of zinc ore mined in the local area as well as that imported from distant states. With the war, new interest in the exploitation of the metallic ores of the region lends new significance to the gas reserves tabulated herein. Geological Discussion The region covered in this report comprises the Arkansas Valley from Pope County weslward to the Arkansas-Oklahoma state line as shown in Fig. 2. This valley is a westward trending structural trough with sharp-topped ridges and mesa-like mountains rising above the valley's undulating surface. It is bounded on the north by the Ozark Highlands and on the south by the Ouachita Mountains. The sedimentary beds of the Arkansas Valley are composed mainly of noniossil-iferous shales and sandstones. The rocks contain a high content of carbonaceous material and many coal beds are found in the region. The Gxed carbon ratios (ratio of fixed carbon to volatile combustible matter of surface coals) are very high and average about 80 per cent over the region covered in this report. Little or no calcareous material is present. Rocks of the Arkansas Valley are sharply folded, and igneous intrusive rocks cut the sedimentary beds at a few places. The Arkansas Geological Survey' made a detailed reconnaissance survey of the Arkansas Valley province in 1927, the purpose being to delineate the major structural features (Fig. 3) and to point out the possibilities of discovering addi. tional gas deposits. More than fifty anticlines were mapped as a result of this survey. The information gained by this

Jan 1, 1943

By D. Jenkins

THE Franklin Laboratory was designed mainly for the analysis of the products from the two concentrating mills situated at Franklin and Sterling Hill, the most important determinations being the zinc, iron, manganese, lime, moisture and silica contents of the ores. Within the last 4 years, however, it has been found advisable to examine most of our supplies, and therefore additional space and equipment was allotted for the examination of such substances as oils, greases, soaps, alloys, fuels, paints, explosives and water. The building as shown in elevation (Fig. 1) and plan (Fig. 2) consists of a main or routine laboratory, an experimental laboratory, a water FIG. 1.-WEST ELEVATION. analysis room and the other accessories such as stock room, library, sampling and drying rooms and office. The main laboratory is further divided into a balance room and zinc analysis room. As the greater part of our determinations are volumetric, good light is a very important factor and with this in view the interior walls of the building were constructed of white enameled brick laid in Keene cement. These also have the additional advantage that they give a clean and attractive appearance to the room. The windows are large, being 76 by 44 in. and even on very dark days the light is good throughout the whole laboratory. Our zinc titration requires a constant light and as, on many days, especially in winter, the light is variable, we installed two Artificial

Jan 8, 1917