Search Documents

By Franklin H. Sharp

The operation of the Magmont Concentrator located on the New Lead Belt of Southeast Missouri is described. Ore characteristics affecting lead-copper-zinc separation are enumerated, and the cur- rent methods of separation are detailed.

Jan 1, 1976

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By Albert Sauveur

The instrument about to be described meets so perfectly the special needs of the metal microscopist that there eeeme to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.—The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement affords free space below the objective for the examination of large epecimens of metals, such as full rail-sections, without detracting in the least from the value of the

Jan 1, 1912

By Andrew Mayer

Early in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. E. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense PlantCorporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at I0,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. The Process The process, in brief, is as follows: The raw materials are dolomite and ferro-silicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to then reaction 2(MgOl CaO) + Si = 2Mg + zCaO, Si% It is distilled from the charge and con- densed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of 14 tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. Choosing the Site The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. in the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO and not more than 2 per cent acid-insoluble material. Second, the dolomite should

Jan 1, 1944

By J. S. Koehler, F. Seitz

THE dislocation theory of plastic flow originated in 1928, when Prandtl1 suggested that the internal damping of metals of plastic origin might arise from the motion of a crystalline imperfection. Following this, Dehlinger2 employed a similar imperfection in a theory of recrystallization. The first detailed theoretical discussions were those of E. Orowan3 and G. I. Taylor4 in 1934. The resulting theory was gen- eralized by J. M. Burgers5 in 1939. Mott and Nabarro, in England, and Seitz and Read,6 in the United States, started an extensive examination of the atomic theory of dislocations in the period between 1939 and 1941. However, this development was arrested by the mar and was not taken up again until after 1945. Since 1946, the field has been the object of very intense activity, particularly in the United States and England. Dislocations are beautiful and intricate imperfections; they are sufficiently complicated to account for the great variety of phenomena encountered in the field of plastic flow. Above all, the dislocation concept enables us to understand how a metal or other plastic solid can deform inelastically under very small stresses at temperatures far below the melting point. Suppose we attempt to shear a perfect crystal plastically. This can be done by sliding one entire atomic plane simultaneously through one atomic distance with' respect to the near-

Jan 1, 1954

By Richard H. Siller, Rex B. McLellan

A model for interstitial solid solutions has been considered in which a repulsive Potential exists between interstitial atoms in the solvent lattice. It has been shown that this model is consistent with the thermodynamic Properties of certain interstitial solid solutions. The model is then applied to the calculation of the variation of the diffusivity of carbon in au-tenite with composition. Although the energy levels at the saddle point, and thus the absolute values of dif-fusivity, cannot be calculated, it is shown that by taking the repulsive interactions between the diffusing atoms into account the functional form of the dependence of diffusivity on solute concentration can be derived. ThE composition dependence of the diffusivity, D, of carbon in austenite at a given temperature is well-known.'-3 smith3 tried to reconcile the observed composition dependence of D at 1000°C with the previously observed4 composition dependence of carbon activity using equations for D derived by arken5 and Fisher, Hollomon, and Turnbull,6 but was unsuccessful. In this paper we shall modify the approach of Fisher et al. by considering the "blocking" model7 for interstitial solid solutions, based on concept due to Speiser and Spretnak,' in which a repulsive potential exists between interstitial solute atoms in the solvent lattice, causing a certain number of interstitial sites to be "blocked" from occupancy by further solute atoms. We shall thus be able to describe the intimate relationship between the composition dependence of carbon diffusivity, a kinetic phenomenon, and the composition dependence of carbon activity in austenite. THEORY Consider for convenience one-dimensional interstitial diffusion in an fcc lattice in the [loo] direction. Fig. 1. Assume that solute atoms occupy octahedral sites only.7,9'10 These octahedral sites are located on {lOO} planes a/2Å apart. A solute atom, A, occupying an octahedral site on a {100 } plane denoted by 2, has twelve nearest-neighbor octahedral sites: four on plane 1, four on plane 2, and four on plane 3. Diffusion occurs when there is a net flux of solute atoms, through an imaginary plane shown with dashed lines, from plane 2 to plane 3. Fisher et al6. use the concept of activated complexes, as given in the theory of absolute reaction rates." They show that the number of solute atoms per cubic centimeter per second which pc — Fig. 1-Diagram showing the arrangement of octahedral sites (x) in the fcc lattice. pass in the direction of diffusion from activated to new interstitial position is: ?where C is the concentration of the solute in atoms per cubic centimeter, l/m + is the fraction of new interstitial positions corresponding to motion in the forward diffusion direction (transmission coefficient), ?F* is the free-energy difference between the activated complex and the reactants when each is in its standard state at the temperature of the reaction (independent of temperature and composition in the case of carbon in austenite), y is the activity coefficient of the solute species, and, finally, ym is the activity coefficient of the activated complex (assumed constant). The flux of atoms moving in the forward direction through an area of 1 sq cm perpendicular to the direction of diffusion is therefore: m+ Ym l ' atoms per second where is the distance between planes. The blocking model states that a nearest-neighbor octahedral site of a given solute atom has a probability, f, of being inaccessible to other solute atoms. The number of available sites for diffusion on a given plane will, therefore, depend on f, which is constant, and Nu, the number of solute atoms on that plane. The effect is to have more available sites in the diffusion direction, thereby increasing the net flux of solute atoms. This is reflected in the transmission coefficient, l/m. To calculate the transmission coefficient for solute

Jan 1, 1970

By L. H. Lange

It is the author's opinion, based on many field experiences over several years, that it is usually better to design a rougher flotation circuit with long rows of rougher cells for high tonnage capacity for maximum recovery and better operating efficiency than the alternative of a greater number of shorter rows with proportionately less tonnage of feed per row. Recent plant studies and tests in the 12,000 ton per day flotation plant of the Atlas Consolidated Mining and Development Corp., Cebu, P. I., have given further substantial support to this opinion. There are two flotation sections in this concentrator: 1) Section 1, treating half the tonnage to the total mill, has eight rows of rougher cells, each row containing 360 cu ft of cell volume. Accordingly, each row of cells receives, on the average, 750 tons per 24 hours which assays about 0.65 to 0.75% copper. The main copper mineral is chalcopyrite with minor

Jan 11, 1963

By Joseph W. Leonard

Partition (Tromp) curves, as used in diagnosing problems in coal cleaning equipment, are discussed and classified using five arbitrarily chosen types to represent, on a scale from one to five, system performance. Causes of unsatisfactory Tromp curves for various cleaning units, ranging from operational inadequacies to problems best corrected by the equipment builder, are analyzed.

Jan 1, 1982

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By D. J. Sellmyer

In order to orient single crystals by the back-reflection method it is necessary to know the angles between the various crystallographic planes. These angles have already been published for the hexagonal close-packed metals magnesium, zinc, and cadmium.'

Jan 1, 1965

By R. W. Raymond

I desire to call the attention of members of the Institute to a new method of plotting and determining faults in mineral deposits, suggested by Prof. Hanns Hoefer, lately of the Mining School of Przi-

Jan 1, 1882

By John M. Karpinski, David S. Cahn

For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate tests. In addition, the dependence of these tests on such pellet properties as size and weight was to be investigated.

Jan 7, 1969

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By William Kent

More than twelve years were spent by Wöhler at the instance of the Prussian Government in experimenting upon the resistance of iron and steel to repeated stresses. The results of his experiments are expressed in what is known as Wöhler's law, which is given in the following words in Du Bois's translation of Weyrauch:* " Rupture may be caused not only by a steady load which exceeds the carrying strength, but also by repeated applications of stresses, none of which are equal to the carrying strength. The differences of these stresses are measures of the disturbance of continuity, in so far as by their increase the minimum stress which is still necessary for rupture diminishes." A practical illustration of the meaning of the first portion of this law may be given thus: If 50,000 pounds once applied will just break a bar of iron or steel, a stress very much less than 50,000 pounds will break it if sufficiently often repeated. This is fully confirmed by the experiments of Fairbairn and Spangenberg, as well as by those of Wöhler; and, as is remarked by Weyrauch, it may be considered as a long-known result of common experience. It partially accounts for what Mr. Holley has called the " intrinsically ridiculous factor of safety of six." Another "long-known result of experience"—although this has not, as the writer believes, been investigated by scientific experimenters—is the fact that rupture may be caused by a succession of shocks or impacts, none of which alone would be sufficient to cause it. Wrought iron will crystallize by repeated blows in service and become weaker than cast iron. Iron axles, the piston-rods of steamhammers, and other pieces of metal subject to continuously repeated shocks invariably break after a certain length of service. They have a "life" which is limited. Iron rods in bridges sometimes crystallize and break, although the rods in most of our iron bridges

Jan 1, 1880

By R. E. Hobart

The development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines, led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was 2 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 1, 1918

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By Harrison Schmitt

DURING the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. HANOVER, NEW MEXICO The Hanover; New Mexico, zinc deposits were briefly described by Lindgren and others,1 Paige2 and recently in more detail by Schmitt.3 These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive 3/4 mile wide and 2 1/2 miles long (Fig. 1). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike; thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1933

By S. P. Goplen, M. Henriksen, T. F. Barron

In the past decade, numerous large scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in [Fig. 1]. Allen 1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping. and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs.2 His data, however, do not reflect sensitivity of flow rate to air/water ratio. Further, in Gibbs' work, air apparently is injec-

Jan 1, 1980

By J. R. Linney

Demand for eastern magnetite in 1948 necessitated practically all eastern magnetite industries to operate on a six-day week, with the result that over 11,000,000 long tons of crude ore were mined, and the shipping products amounted to approximately 5,000,. 000 long tons. Reports indicate that operating on a six-day week and doing maintenance work on the seventh day was satisfactory and resulted in excellent continuity of operation. In the Port Henry district, Republic Steel Corp. once again set new all-time records for the production of crude ore and total shipping product; 1,868,000 long tons of crude ore were mined, 945,000 from the Old Bed mine, 408,500 from the Harmony mine, and 514,500 from the Fisher Hill mine. Of the 969,000 long tons of shipping products, 663,800 long tons were sinter, 181,000 lump ore, and 115,200 con¬centrates.

Jan 1, 1949