Search Documents

By Hamish D. S. Miller

Currently the underground potash mines in Canada extract about 40% of the available ore, leaving the other 60% behind in the form of stabilizing pillars. The presence of water in the overlying formations requires that any disturbance due to mining be such that no water will enter the workings. This paper deals with the factors that influence the stability of the rock surrounding the mine excavations and looks at the effects of these factors when a system of increasing the extraction is considered.

Jan 1, 1983

By J. R. Dawson, J. A. Glunt

VESTA No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's byproduct coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War 11, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out. Mechanical loading at Vesta created new problems. It was found that selective mining, even when carefully applied, increased the refuse in the raw coal to such an extent that the washers at the mills were unable to handle it. Large tonnages of refuse were being transported, a reject disposal problem was created, and good metallurgical coal was being loaded out and lost. In addition, the selective method handicapped operation of the loading machines. Fig. 2 shows how the ash content of the raw coal increased as mechanization proceeded at No. 5 mine. New Preparation Plant: After an exhaustive study of this situation by J & L management, is was decided that a preparation plant should be constructed at the mines, capable of handling full seam mined coal and large enough to process full production of both No. 4 and No. 5 mines. It was decided that from the standpoint of inside operation and haulage the new plant should be located as near as possible to the old No. 5 tipple on the Monongahela River near Vestaburg. Full seam mining at Vesta could be expected to produce a tremendous volume of refuse along with the coal, since 14 to 16 in. of slate would be mined with an average 78 in. of coal. Disposal of this refuse required serious consideration in selecting a plant site. The only area near Vestaburg large enough for disposal of the plant refuse was across the Monongahela River at LaBelle. Ample space was available here, and construction at this location would not interfere with operation at the No. 5 tipple. It had been noted over the years that the sulfur content of the coal produced at Vesta was gradually increasing, and there was every indication that this increase could be expected to continue as the mines developed further from the river. It was decided to construct a three-part separation plant with complete blending facilities to produce both metallurgical and steam coal. In this system an attempt is made to reduce the sulfur in the metallurgical coal in a secondary cleaning process. Construction of the new preparation plant got under way early in 1947 and continued until the spring of 1950. The plant was designed to handle 2400 tph of raw coal containing 30 to 35 pct refuse. Cost of outside buildings and equipment was about $14 million. Total cost of the plant, together with improvements and changes made at this time, was approximately $21 million.

Jan 1, 1957

By J. F. Evers, S. Sadiq, F. W. Preston, G. W. Swift

Proper scaling of unsteady-state flow in laboratory gas reservoir models can be achieved if the permeability/fractional porosity ratio is less than 0.5 md. Porous media meeting this specification can be obtained from mixtures of sand and Portland cement provided (1) the water/cement ratio is in the range of 0.35 to 0.40, (2) the sand/cement ratio is in the range of 1/1 to 2/1, (3) the sand grain size is in the range of 48-100 to 18-28 mesh, (4) the mortar curing time is 7 days or more and (5) the cured mortar is dried under vacuum to reduce the temperature level employed during the drying process. The areal homogeneity of the mortars tested is reasonably good, although significant trends in vertical permeability were noted. The Klinkenberg and non-Darcy coefficients of mortar are such that proper scaling of these effects in the laboratory model could be expected. INTRODUCTION A long term deliverability prediction for a gas well is generally based on data determined from flow tests that are of short duration relative to the producing life of the well. These data, together with an estimate of gas reserves in place, form the basis for establishing the parameters of the mathematical model used to predict performance at future times. Results obtained from a mathematical model represent only an interpretation of the physical process being modeled. Experimental verification of the production process from discovery to abandonment is needed where production occurs under carefully controlled conditions. Ideally, one might consider such an experiment to be conducted in the field. Even if the cost of such an experiment could be justified, the time required would make it impractical to consider. However, if the time scaling problem could be handled properly, an experimental model of the gas reservoir production process could provide the necessary data to study the mechanisms of the production process in a reasonable time period. An experimental model has been designed and constructed using the data of this study as a basis. The model reservoir system consists of one producing well located at the center of a right-circular cylinder of porous material. Ten to 15 observation wells are located at strategic offset positions from the producing well. These wells, and the producing well, are fitted with pressure transducers so that the pressure-time history can be recorded at various radial and azimuthal positions in the drainage area during the entire production life of the system. Time is scaled in the model so that the time required to produce gas from discovery pressure to abandonment pressure is about 2 hours. This compares with a 20-year producing life in the model's field counterpart and gives a time scale factor of approximately 1:100,000. DESIGN CRITERIA To establish design criteria for the experimental model, the reservoir is considered to be a finite right-circular cylinder of radius rr, and height h with a producing well of radius rw located at the center and completed through the producing formation. This reservoir consists of a porous medium which has a uniform permeability k and gas porosity and the gas contained in the reservoir has density p, viscosity µ and molecular weight M. Initially, the pressure at all points within the reservoir is uniform at po. and the reservoir temperature is T. Since the reservoir production process has been demonstrated to occur in two distinct transient modes for either Darcy or non-Darcy flow,l it is

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1982

By J. M. Floyd

The theory, construction and applications of oxygen sensors employing high-temperature electro- chemical cells with solid electrolytes are briefly reviewed. The application of disposable probes to measurement of the oxygen potential in matte and slag baths in tin, copper, and nickel smelting operations is described. Examples discussed include end-point determination in smelting and slag-cleaning operations, pilot-scale investigations of process chemistry to assist in the development of smelting strategies, and measurements in operating smelters to improve the efficiency of operation.

Jan 1, 1984

Jan 1, 1932

Jan 1, 1932

By W. S. Ayres

The protractor here to be described embodies several important improvements that have been suggested by the use of other protractors and by observing the errors occurring in practice with them. It is more particularly an improvement

Jan 1, 1896

By I. R. M. Chaston

Radial layout’s guiding principle is the grouping under one roof of the operating processes which require continuous supervision. Separate treatment sections are isolated by outside stockpiles fed with radiating conveyors. Hence the name ‘radial’ layout. Many plants are designed with ‘linear’ layout where successive operating stages are dotted like beads along a string of conveyors. [Figures 1 through 5] show the development of the radial concept in the layout of heavy-media diamond recovery plants over

Jan 1, 1979

SUGGESTIONS that existing schools give instruction bearing on the mineral industry, or that schools for that purpose should be established in the United States, began to be made early, and it would require too much space to catalogue them all. Some of the more important may be mentioned to indicate their general character. In the "advertisement to such parents as have now (or expect to have) children prepared to be educated in the College of New York," which appeared in the New York Mercury of June 3, 1754, Samuel Johnson, the first president of King's College, the predecessor of Columbia, said that it was the "design of this college to instruct and perfect the youth," among other things, "in the arts of Numbering and Measuring of Surveying, and Navigation and Geography. . . . and in the Air, Water and Earth around us, and the various kinds of Meteors, Stones, Mines and Minerals, Plants and Animals; and in the knowledge of all Nature in the Heavens above us, and of everything useful for the Comfort, Convenience and the Elegance of Life . . . " Though the concept that natural science should be used to enlarge the bounds of human life was thus implicit at Columbia from the , very beginning (John Stevens graduated from it in 1768, James Renwick in 1807, Horatio Allen in 1833, and A. W. Craven in 1899), it was only during the period of Renwick's professorship of Natural and Experimental Philosophy and Chemistry (1830- 1853) that much attention was given to applied science.* Among the Austin papers, published by the American Historical Association,~ there is a draft in Stephen F. Austin's handwriting of a proposed memorial from the legislature of , Missouri to Congress, not only urging "the propriety and utility * See chapter 4 for early interest in this subject in Philadelphia.

Jan 1, 1941

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for upgrading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching. ALL of our larger domestic deposits of manganese are very low grade, but estimated tonnages in these deposits are large enough to constitute a potential strategic reserve of manganese for emergency periods, provided these ores can be upgraded sufficiently to meet industrial specifications. Many types of processes have been suggested for upgrading these ores, several have been studied in pilot plants, and a few have attained limited commercial production for special purposes. The hydrometallurgical process to be described below proposes a leaching operation for removing caustic-soluble silica and other gangue minerals and consequently upgrading a manganese ore or flotation concentrate to a commercially acceptable moduct. It is known that some forms of silica and some silicate minerals are soluble in NaOH solutions under suitable conditions. This new process proposes to use NaOH for removing the soluble materials from manganese ores or concentrates and, as a result, upgrade the manganese content. Since spent leach liquors are not efficient leaching agents the liquor must be treated with lime to precipitate calcium silicate and reactivate the NaOH. Experimental Procedure Manganese-ore samples ground to —35 mesh were leached in iron containers into which the ore sample and appropriate NaOH solutions were placed. Flotation concentrates were already ground to —200 mesh. The slurries were then placed on a hot plate or into a pressure digester and stirred continuously during the period of digestion. Where the- digestion was performed at atmospheric pressures, water lost by evaporation was replaced at regular intervals to maintain approximately a constant volume of slurry. In the pressure digester, volume changes were not controlled. After digestion, the slurry was allowed to cool enough for easy handling, but it was filtered hot, 50" to 70°C, on a Buechner filter. Filtration under these conditions was satisfactory. The resulting filter cake was washed and dried. In most instances, a single leach would not produce maximum extraction of silica from the ore sample; consequently, the dried tailing was treated again in the same manner with a fresh solution of NaOH to obtain an additional extraction of silica. This procedure was repeated a number of times to get the maximum extraction of silica. Usually three or at most four stages of leaching were adequate for this purpose. This leaching procedure was used for obtaining the data reported in this paper on the effects of NaOH concentration, pulp dilution, temperature, and time of digestion on the efficiency of extraction of silica from the ore sample. The experimental procedure does not match industrial methods. consequently tests for counter-current leaching were set up. Data from these tests are not yet complete, but in a qualitative way they indicate that thickeners between stages of leaching will be satisfactory and that the quantity of silica in a leach liquor moving forward to a new solid has only a minor effect on the quantity of silica extracted from the new solid. A pilot plant is now being designed for operation in the near future to test and evaluate the merits of this process.

Jan 1, 1954

By Benny J. Nelson

AS a part of the fundamental research program of Aluminum Research Laboratories, some data were obtained on the ternary system Mg-Al-Mn. As very little information on the magnesium corner of this diagram has heretofore been published, it seems desirable to make available the values found for the liquidus and solidus surfaces of this system. Procedure The settling procedure was used for the determination of the liquidus compositions. Metallo-graphic examination of quenched samples, and stress-rupture upon incipient melting, were used for the solidus determinations. The settling procedure has been described in a previous paper.' Briefly, this method involved saturating the alloy with manganese at a temperature substantially above that at which the sohbility was to be determined, then cooling the melt to the latter temperature, and holding it at that temperature for a substantial period of time. Samples for analysis .were carefully ladled from the upper portion of the melt at hourly intervals during the holding period. After the ladling of each sample, the melt was stirred to redistribute some of the manganese that had already settled, because it appeared that when the latter particles of manganese again settled, they aided in carrying down more of the manganese and thus hastened the attainment of equilibrium. The melts were prepared and held in a No. 8 Tercod crucible holding approximately 4 lb of metal. The manganese was added either in the form of a prealloyed ingot (Dow M) containing about 1.5 pct Mn or by the use of a flux (Dow 250) containing manganese chloride. In calculating the flux additions, it was assumed that the manganese introduced would be equal to 22 pct of the total weight of the flux. Temperatures were measured with an iron-constantan thermocouple enclosed in a seamless steel tube, the lower end of which was welded shut. This protection tube also served as a stirring rod. The samples ladled from the upper portions of the melts at the various intervals were analyzed for aluminum, manganese, and iron. When making the alloys which were to be used for the determination of the solidus, 2½ in. diam tilt mold ingots were cast, scalped to 2.0 in. in diam, and extruded into ? in. diam wire. The principal impurities in the melts for this investigation were iron and silicon; their total not exceeding 0.03 pct. Portions of the wire, approximately 2 in. in length, were enclosed in stainless steel capsules for protection from the atmosphere. Bundles of these capsules, with a dummy capsule containing an iron-constantan thermocouple, were heated inside a large steel block (acting as a heat reservoir) in a closed circulating-air type electric furnace. At ap- propriate times, the capsules were removed and quenched in water. The wires were examined metallographically to determine the temperature of initial melting. Short times at temperature were used at the beginning for wire specimens of all alloys to obtain quickly the approximate temperatures at which melting could be first observed. When approximate solidus temperatures had thus been determined, equilibrium heating was attempted. This equilibrium heating consisted of an 8 or 16 hr period at a temperature, about 50 °F below the lowest temperature at which melting occurred when short heating cycles were used, followed by further heating for 1 hr periods at consecutive 10" higher temperatures. The theory for the method of stress-rupture at incipient melting has been well covereda and its limitations are recognized. Thus, if the interfacial tensions are such that the first minute quantity of liquid is "bunched up" at the grain boundary junctions instead of spreading out along the grain boundaries,³ temperatures higher than the solidus are required before melting will be manifested by rupture of the specimen. This point will be elaborated later. Specimens of the wires with a reduced section (approximately 1/16 in. diam) were suspended vertically in a tubular furnace. The setup used is shown in Fig. 1. The clamp holding the specimen was made from alumel thermocouple wire and the thermocouple was thus completed across the specimen by attaching a chrome1 wire to its lower end. Temperatures were read from a Speedomax recorder used in conjunction with a calibrated thermocouple. The small weight attached to the specimen and a vibrator attached to the furnace tube, to aid in distributing the molten constituent along the grain boundaries, were used to bring about rupture at a temperature closely approximating the solidus. The specimens were heated at a rate of about 5°C per min. The rupture of the specimens was indicated both by sound and by the action of the recorder. An argon atmosphere containing a small amount of SO² was used for protection of the specimen. The assembly was taken out of the furnace immediately following rupture and the specimen removed. Some of the broken specimens were examined metallographically and will be referred to later. Results and Discussion Fig. 2 shows a set of typical time-composition curves for liquid samples of the Mg-Al-Mn alloys used for the settling tests. The data as presented

Jan 1, 1952

By M. Weinstein, J. F. Elliott

IN conjunction with a study on the solubility of hydrogen in liquid pure iron and iron alloys, new and

Jan 1, 1963

By EUGENE MCAULIFE

Jan 1, 1934

Jan 1, 1932

By R. W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from nonkimberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques where spectral bands are chosen to optimize contrast between the kimberlitic soils, nonkimberlitic soils, and vegetation. Careful processing of the multispectral data is essential to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1986

By D. L. Everhart

The search for new deposits raises two important questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? A review of the wide geological variety of recent uranium discoveries tells how these questions are being answered. SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the overall job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Compared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits. One of the most interesting features of known uranium deposits of the world is the wide variation, see Table I, in character and geologic environment. It should be noted that many types became prominent during 1953. The davidite-bearing veins of Radium Hill, South Australia, are almost unique, although the same mineral occurs in a different kind of deposit in Mozambique. Recent studies indicate that brannerite disseminated in the granite near Cracker's Well, South Australia, may soon constitute uranium ore. Basalt has been added to the list of favorable host rocks in the Northern Territory of Australia. Basalt is also the host of the pitchblende veins of the Martin Lake deposit, Beaverlodge district, Saskatchewan. The truly remarkable rich and extensive Steen deposit near Moab, Utah, is of the uraninite-vanadium oxide type. Secondary hydrous uranium arsenates and phosphates constitute the uranium minerals in the disseminated deposits of the Wind River Basin, Wyo., a new district discovered in the summer of 1953. Uranium minerals in shales adjacent to fractures were newly reported in New Mexico and several other parts of the world during the year. The well-known important uraninite dissemination in the Rand conglomerates of South Africa has a counterpart, as discovered in the summer of 1953, in the Mississagi quartzite and conglomerate of the Blind River district, Ontario. Gunnar deposit of the Lake Athabaska district, Saskatchewan, consists of uraninite in both granite and sedimentary gneiss beneath a granite cap, and large new orebody of the Eldorado Co. in the same general area follows a preferred stratigraphic horizon in schists. Uranium is, generally speaking, a very soluble and ubiquitous element. It occurs in at least two valency states and for this reason is not easily tied down in natural solutions. As Gruner' has pointed out, it is probable that uranium starts in the hexava-lent state in nearly all solutions instrumental in its transfer. It is believed that under oxidizing conditions the uranium moves in solution as the uranyl ion, UO. In solutions ranging in pH from 1 to 5, the uranyl ion is most commonly in association with

Jan 1, 1955

By John Wellington Finch

In August, 1927, the writer examined certain copper deposits in New Mexico1 which occur in beds of sandstones and shale, and in connection therewith reviewed the literature upon deposits of this type. Such deposits are known and have been reported upon at various points in Texas, Oklahoma, Arizona, Colorado, Wyoming and Utah, but in New Mexico they have been given more development than elsewhere and apparently occur there more conspicuously than in the other states. Some 25 years ago the writer examined deposits of similar origin in northern Arizona and more recently other deposits in western and southwestern Colorado, and these examinations have led him to realize how widely scattered are the deposits and how generally noncommercial they are. On superficial development, to one without a comprehension of their geologic nature, they are alluring on account of occasional small amounts of high-grade ore and much misplaced capital has been expended upon them. This paper, therefore, aims to present briefly certain theories of genesis, some details of which may possibly be new, and to lead up to practical conclusions which may be useful to other geologists and engineers. A bibliography of the more important literature upon such deposits is given below.2 Coffin's Bulletin upon the Radium, Uranium and Vanadium Deposits of Colorado, published in 1921, is a particularly clear discussion. The most comprehensive recent statement is Butler's.

Jan 1, 1928

By I. Cornet

INTRODUCTION WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943 1; it has been released for publication by the O.S.R.D. SCOPE OF THE INVESTIGATION The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with the notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and M. For comparison, extrusions of aluminum alloy 24S-T, cast bars of aluminum alloy I22-T2, and cast bars of magnesium alloy C were also tested, The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of the tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the changing hardness, tensile strength, microstructure, and notch sensitivity observed. EXPERIMENTAL TECHNIQUES AND PROCEDURES Tensile Testing Bars used for axial loading were machined with 3/8 in.- and with 1/4-in. minimum diam, and included specimens with 6o° V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These V-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1948

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925