Search Documents

By H. F. Yancey

One of the important duties of the Bureau of Mines is to sample and analyze coals and to publish the results of such analyses for the information of producers, consumers, and the general public. Numerous publications containing such analyses have been Issued from time to time. Although the chemical properties of a coal as revealed by its proximate and/or ultimate analysis and heating value aid one considerably in visualizing its probable behavior and in determining its usefulness and value for a specific purpose, they do not furnish complete information. The physical properties of a coal, such as its ability to retain its original form without undue breakage or degradation in size under the various conditions of storage and usage, are also of importance in determining its suitability, technically or economically, for a given purpose.

Jan 1, 1932

By Baruch Grinbaum, Edwin Bwalya, Robert Minango, Deogratias Bukunkwe

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well known and established process. As the process advances, Cu is extracted to the solvent and is replaced by H+ in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: 1. SX-1: Standard extraction of Cu with oxime. The resulting raffinate contains about 6-8 g/L Cu and 50 g/L H2SO4. 2. SX-N: Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3 etc. The extraction removes no metals, but decreases the concentration of acid from 50 to 10 g/L. 3. SX-2: Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100-150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility in Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory scale, the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX-2 2-3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with Alamine based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 & SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E=2S for SX-2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By Janine Pierce, Robert Larson, Christine Raasch

The vibration and impact environment for crew members on locomotives has been investigated in a series of studies conducted by Exponent Failure Analysis Associates (Exponent) beginning in 1990. Locomotive cab vibration and impact levels were measured on a variety of locomotive models operating over many different track sections across the Union Pacific, Burlington Northern Santa Fe, CSX, Norfolk Southern, and CONRAIL systems. The comfort and health implications of exposure to the measured locomotive vibration levels were evaluated by comparison with the human vibration exposure boundaries given in the International Standards Organization (ISO) standard 2631-1:1997, the British Standard 6841:1987, European Union (EU) Directive 2002/44/EC, measurements made by Exponent on various commercial and recreational vehicles, and vibration exposure measurement data found in the literature. Methods Initially, vibration levels experienced by locomotive crews were measured and recorded at incremental speeds covering the range of normal train operation. In 2003, a method of measuring the vibration exposure continuously by means of a digital recorder was developed, allowing the vibration level over the entire run or crew shift to be analyzed. For each seating location measured, acceleration was recorded on the seat surface beneath the ischial tuberosities (pelvis) of the seated crew member and on the cab floor directly under the seat. At each of the locations, triaxial accelerometers were used to measure the vibration along the longitudinal, lateral, and vertical axes. Since the vibration environment varies throughout the route, and locomotive vibration levels have been found to be primarily speed dependent, a speed sensor was used to continuously measure the speed of the train. To evaluate the recorded vibrations levels, the data was divided into two-minute segments, which were each processed per the 1997 ISO standard for weighted RMS vibration levels and Vibration Dose Values (VDV). Additionally, PSDs and 1/3 Octave RMS values were calculated to determine the frequency content of the vibration. For each two-minute segment, the average speed of the locomotive was calculated to allow for correlation with the recorded vibration exposure values. The resulting exposure values for the entire run were calculated by combining the data from all of the two-minute segments. Since introducing the continuous method of recording acceleration, 23 seating locations have been recorded on 11 locomotives traveling 11 different routes across various parts of the United States. One of the routes was a shift of ‘yard work’, traveling back and forth in a rail yard coupling train cars together. Results A guide to interpreting weighted acceleration values with respect to health is given in Annex B of the 1997 ISO standard. A health guidance caution zone is defined to indicate the

Jan 6, 2006

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By Simons W.

The object of the paper is to describe the standards of quality that should be specified in ordering material ordinarily required for colliery use, and also the qualities most suitable for particular purposes. Tables are presented of British Standard tests for wrought iron grades A, B and C, Admiralty tests for iron in chain, the quality of material for wheels and axles, and the composition and mechanical properties of wrought iron, Armco (ingot) iron and drawbar-gear steel. (Paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, Mr. John Gregory, President, in the chair)

Dec 1, 1916

By AIME AIME

AT the Morenci branch of the Phelps Dodge Corporation, of which Frank Ayer is manager, several new types of machines that have been developed by Charles Mitchell, shop foreman in the drill steel shop, invite comment for their time and labor-saving qualities. Foremost of these is an adjustable gage-block and gaging device for attachment to drill-sharpening machines, developed and patent applied for by Mr. Mitchell. It replaces the blocks on the standard Ingersoll-Leyner drill steel sharpener No. 5. Features of the device are gage blocks with a flat surface which can readily be removed when worn and planed in any flat planer; blocks that can be adjusted with a templet to give a far more accurate gage than was formerly possible; and a center stop that is adjustable and can be accurately set to center any standard size drill steel.

Jan 1, 1930

By D. Duvris

Health and safety issues are a very important aspect of mining activities. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last 3 decades are presented and critically evaluated with respect to number of workers, annual production, etc. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greek are also discussed.

Jan 1, 2000

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940

By William Seymour, L. D. Schmidt

"FOREWORDAmong many problems created by World War II, the question of supplies and distribution of raw materials is of outstanding importance. One of the most critical of these raw materials is fuel, and of the fuels coal is of primary importance. The normal consumption of coal has increased greatly owing to the increased tempo of industry in general. It has been necessary to divert much of the fuel oil, gasoline, etc., ordinarily used for industrial and domestic purposes, to supply the enormous demands of mechanized warfare. Coal must be provided to replace this fuel. Furthermore, the enormous increase in the production of steel has increased the demand for coking coals to a critical point.The Solid Fuels Administration for War is encouraging the use of anthracite fines in the production of byproduct coke for blast furnaces for three reasons. First, the production of anthracite for domestic use; is hampered by the inability to find a market for the fines incidental to the production of domestic sizes. Second, the shortage of low-volatile coking coal is acute, and any action that will decrease the quantity of low-volatile coal required will relieve the situation. As will be seen in this report, there is some promise that use of anthracite fines in coke-oven mixes will lower the amounts of low-volatile coal required. Third, utilization of those anthracite fines will tend also to alleviate the general fuel shortage. It has been the privilege of the Bureau of Mines to cooperate with the Solid Fuels Administration in the technical problems involved."

Apr 1, 1945

By J. B. Gwiazda

S. Budirsky J.B. Gwiazda's article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point 0 travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex'85, Katowice, Poland, pp. 73-83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4500 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (1a in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the aforementioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda's opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf-Forschungshefte, 1984, No. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1987

By AIME AIME

THE climax of the various programs and entertainments in connection with the holding of the World Engineering Congress* in Tokyo in October was the complimentary dinner given by the visiting members of the Institute to our members in Japan. At the same time President Bradley conferred an honorary membership on Baron Takuma Dan, the vice-president of the World Engineering Congress.

Jan 1, 1930

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spectroscopy has been employed to· examine the role of tetraperoxochromate( V) ions (Cro:-) and other Cr(V) species in the generation of hydroxyl (OH) radicals in the reaction of Cr(VI) with H2O 2 in biological media. In contrast to earlier suggestions, the present ESR studies using crystalline K3CrO8 as a source of Cro:- show that decomposition of Cro:- in water or in H2O 2 does not generate significant amounts of OH radicals. Addition of NADH to a solution containing Cro:- yields a Cr(V)-NADH complex, which readily reacts with H2O 2 to generate OH radicals. Similar results obtained from several other biological reductants, including vitamin B2 , indicate that a vacant coordination site on a Cr(V) complex facilitates its reaction with H2O 2 to generate ""OH radicals. We thus suggest that in biological media, reaction [3] instead of [1] or [2] is the major pathway for the OH radical generation: While the carcinogenic potential of Cr(Vl)-based compounds has been well established via epidemiologic and animal studies (1), the underlying biochemical mechanism is still not well understood (2). In a recent development, however, Kawanishi et al. (3) have reported that hydroxyl (OH)2 radicals might be the key species in the mechanism of Cr(VI) toxicity. As to the mechanism of the ""OH radical formation they suggest that Cr(VI) reacts with cellular hydrogen peroxide (H2O 2) to form the tetraperoxochromate(V) (Crog-) ions, which decompose to produce hydroxyl radicals. It was also suggested (3) that the ""OH radicals thus produced cause genotoxicity via DNA base modification and deoxyribose phosphate backbone alterations. More recently Aiyar et al. (4) reported the detection of OH radicals in the reaction of Cr(VI) with H2O 2 in biological media, including the reaction of ""OH radicals with deoxyguanosine to generate 8-hydroxydeoxyguanosine adducts, confirming that ""OH radicals could indeed play a significant role in the mechanism of Cr(VI) toxicity. However, the mechanism for the ""OH generation was not clarified, although the role of Crog- ions as possible precursors was mentioned, somewhat along the lines suggested by Kawanishi et al. (3). The possibility of the participation of Crog- in the ""OH generation has also been indicated by Sugiyama et al. (5), since they mention that vitamin B2 enhances the formation of""OH radicals in the reaction of Cr(VI) with H2O 2 because of the generation of Crog- in the reaction."

Jan 1, 1990

By Forrest T. Moyer

[The safety record of the nonmetal mining industry during 1965 way worse than that of 1961 in all general measures s of injury experience except for a slight improvement in the number and frequency rate of nonfatal injuries Work fatalities in 1965 totaled al and occurred .it a frequencyrate of 0.29 and a severity rate of 1,711 per million man-hours of worktime. The fatality total was seven oven higher than to 1964 and the injury ratess increased d 32 and 28 present, respectively Thin total. of 2,172 nonmetal injuries u- in 1965 was 3.4 less than in 1964 and the frequency rate per million ion man-hours worked declined percent to 22.73 from: 23.14 in 1964. However, the 1965 nonfatal severity rate of 1,339 per million man-hours worked was 15 percent our the: d.96,1 rate of 1,160, This increases was largely attributable to two more permanent total and nine more permanent partial injuries. in 1965 than in the proceeding year. The average severity all injuries in 1965 was 132 days, 1-I. or charged per injury or 25 days more than in 1961. Injury experience in the nonmetal mining industry, including and excluding officeworkers, for the a-year period 1961-65 is shown in table 1. The average number of men working, on active days in 1963 was 48,429, or 635 fewer than in 1961. However, mines and mills, wore active an average: of 5 days more for a total of 277 in 1965, and each worker averaged 2,245 hours compared to 2', 190 hours in 1961. As a result, aggregate worktime of 108.7 million man-hours increased 1 percent over the 1964 total of 107.4 million hours.]

Jan 1, 1970

By Lyle Dennis

Emphasis on increased production while maintaining rigid quality standards has necessitated a change in blasting technology at Dacotah Cement's limestone and gypsum quarries. The following three methods implemented during the past three years have yielded an increase in production through improved fragmentation.

Jan 1, 1996

By Tor Lindstad

Specific C02-emissions are given for the production of silicon-metal, ferrosilicon, ferromanganese and silicomanganese. Emissions taken into account come from reduction materials, from coke production and generation of electric energy. C02-emissions can be abated by direct and by indirect methods. A direct method is to replace fossil carbon as reduction material wholly or partially by endogenous carbon (biocarbon, charcoal). Another possibility is to produce metals by electrolysis instead of the present electric smelting furnace. Indirectly CO2-emissions can be reduced by energy recovery, thus saving coal, oil or natural gas for heat generation. Some reduction in global C02-emissions can be obtained by giving credit for the use of silica dust partially replacing cement in concrete. In addition to give an overview of possible methods, costs will be discussed.

Jan 1, 1999

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and describes some systems of transportation utilizing rail haulage. ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By E Topal

Stopes are used in several underground mining methods. Boundary determination of these stopes is generally based on simple rules of thumb. While several stope boundary optimisation techniques are available, they fail to guarantee true optimum results. The first part of this paper reviews some important stope boundary optimisation studies and proposes a new algorithm to optimise stope boundaries and layouts for underground operations. The second part applies the proposed algorithm to a block model to test its ability to produce optimum results and demonstrate its applicability in a number of different scenarios. The results demonstrate that the proposed algorithm can find optimum stope boundaries and layouts in three dimensions for different stope sizes and economic conditions.

Jan 1, 2009

By A. C. Moorgas, J. Divall

This study investigates the feasibility of using waste iron slag, the by-product from a mineral sands processing works, in road construction. The study includes the different options investigated for the treatment of a leachate that is produced during the cooling of the iron slag, prior to processing. It also reviews the reasons for choosing the current treatment option that is being trialed. Cooling the iron slag with water results in the formation of a leachate with a high pH and high sulphide concentration. This leachate can seep into the ground and, over time, it will contaminate the ground water. A system was designed to collect and treat the leachate to prevent contamination of surrounding natural water sources. Numerous leachate treatment options were investigated to find cost effective method of treatment After cooling, the iron slag is passed through an iron recovery plant and the unsaleable product is placed on a dumpsite. Rain percolates through the dumpsite, which can result in the formation of a leachate that can contribute to a contaminated plume. After extensive testwork, it was found that the dumpsite, which was leached of contaminants, could be screened and used as a G5material (specifications in Table II) in road construction. The initial challenge was to establish that this material was environmentally safe for use in this particular application. Approval from the Department of Water Affairs (DWAF) was required for the testwork and then for the long-term use of this material in the construction industry. The following challenge involved establishing a market for the material. Construction companies in the area were reluctant to change to a new product that was not naturally occurring. The economics of this project are extremely sensitive to transport costs and hence only projects within a specified radius can be supplied with the Black Top Gravel (BTG). This project is not are venue generator, but it does save the money that would be required to manage the dump, and it reduces the closure costs.

Jan 1, 2003

Australia has a long history of underground mining. Even withadvances in open cut mining equipment, techniques andeconomics, many orebodies are still best mined by undergroundmeans. In addition, modern exploration tools are æuncoveringÆorebodies that are at increasing depths. South African mines arecurrently producing from below 3 km, and developing down to5 km depths û it is likely that Australian mines will also becomemuch deeper over the next 20 years. One of the most significanttechnical challenges in deep mines is the problem of heat.Community expectations and legislated standards continue todrive operations towards improving the working conditions inmines. The hazards and costs associated with chronic hotworking conditions (heat illness, poor safety, poor productivity,higher operating costs and poor morale) are also becomingincreasingly recognised (Brake, Donoghue and Bates, 1998). Theexposure of miners to many other occupational hazards has beenreduced over the past 50 years. However, despite air-conditionedcabins greatly reducing the heat stress on mobile plant operators,there are still many Australian mine workers subject to levels ofthermal stress that existed a century ago. There are severalreasons for this, including a frequently-poor understanding of thephysiology of working in heat by mine management, no agreedmining code of practice for working in heat, the lack of a robust,practical-sized instrument to measure heat stress, the costpressures on the industry and, to some extent, deep-seatedtraditional management and worker practices. Howeversignificant progress has been made in many of these areas (Brakeand Bates, in press), with the net result that there is likely to be a trend towards installation of refrigeration of some form in manyAustralian mines in the future. This will add directly to the costof operation, but will also have direct and indirect benefits,including cost benefits. It should also be noted that Australia isnot at the forefront of adopting practices to manage temperaturesin the workplace: South African metal mines usually haverefrigerated cooling, and Canadian mines spend large sums onheating, with heating costs (averaged over a full year) of up to$A1 per tonne mined (Bandopadhyay et al, 1997). The history of mine refrigeration dates back to 1919 when thefirst plant was installed at Morro Velho, Brazil. By 1965, the totalinstalled capacity (worldwide) reached about 100 MW(R)i. Since 1965 the growth in mine refrigeration capacity has beenexponential, with a doubling every six or seven years (Howes andNixon, 1997). South Africa is by far the largest user of minerefrigeration, with over 300 refrigeration machines installed. This paper discusses the key design issues associated with theapplication of refrigeration in underground metal or coal mines.Whilst the emphasis is on large, surface plants, small, surface orunderground refrigeration plants can also be very effective in thecorrect application and many of the principles of design andoperation are the same.

Jan 1, 2001