Search Documents

By A J. Rorke, U Chhika

"A series of tests was carried out on a dry blend of PPAN and LAN prills (LANFO). The objective of thetests was to determine detonation stability and VOD performance compared to ANFO. Heave andfragmentation results in the field were also evaluated visually. A number of factors were behind for.mulating this blend. A lower cost is combined with higher in-hole energies, but at slower reactionrates and lower peak borehole pressures. The resultant effect is improved heave characteristics andlower energy losses caused by inefficient crushing of the rock immediately around the borehole.The test results indicate that IANFO is ideally suited to blasting in softer midburden and overburdenrock types often encountered in coal strip mines."

Jan 1, 1995

By Shaw Bill

The paper describes of the JORC Code in terms its background working environment and reasons for success, and provides references to papers which cover the subject in more detail. It then discusses the two major developments in Australasian reporting standards in the last two years: the revision of the 1999 Code, and the introduction in early 2003 of the “ROPO” (Recognised Overseas Professional Organisation) initiative. The purpose of the JORC Code is to provide a minimum standard for reporting of Exploration Results, Mineral Resources and Ore Reserves in Australasia, and to ensure that public reports on these matters contain all the information which investors and their advisers would reasonably require for the purpose of making a balanced judgement regarding the results and estimates being reported.

Apr 22, 2003

By I M. Howard

With the bell-less top (BLT) charging system replacing the centuries old double bell charging method, the furnace efficiency has been greatly improved together with considerable reduction in the furnace down time and operational problems. But still there are many draw-backs which need further attention to achieve better efficiency and operational effectiveness. The performance and operational problems of the BLTs have been highlighted and possible solutions to overcome some of the major problems are discussed.

Jan 1, 1999

By Dennis A. Swyt

In current post-industrial America, U.S. manufacturing is undergoing major changes both in the technology of its production and in the size and composition of its workforce. At the same time that computers and robotics move the shop floor toward becoming the unmanned "factory of the future" [1], they increase the need within the overall production enterprise for new types of technicians and engineering professionals [2]. Based on previous works which examined, first, the evolution of the technology of manufacturing toward the flexibly-automated factory of the future and, second, the technical- professionalization of U.S. manufacturing sectors [1,3], this paper looks briefly at the workforce of the U.S. metals industry.

Jan 1, 1989

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By P. -E. Boileau, P. Marcotte, Y. Aldien, S. Rakheja

A number of biodynamic models of the hand-arm system have evolved on the basis of measured driving-point mechanical impedance (DPMI) responses to facilitate analyses of the coupled hand-tool system [1]. The parameter identifications in such models are based upon minimization of an error function of the model and the target impedance data, which may not yield a unique solution. Consequently, a number of model structures and parameter sets could be realized that would equally satisfy the target curve. Moreover, the vast majority of the reported models exhibit acute deficiencies due to excessive static deflections of model masses, presence of a low frequency mode and very light masses in the order of 1.2- 4.8 grams. The models also do not characterize the dependency of the biodynamic responses on many factors, namely the hand forces, hand-arm posture and vibration intensity. This study aims at development of a hand-arm biodynamic model with considerations of the hand forces, and both the DPMI and power absorption measures, to enhance the uniqueness of the model. Methods Two different model structures are chosen for identifying the model parameters on the basis of measured DPMI and absorbed power characteristics of the hand-arm system under zh-axis vibration over a range of hand-grip and push forces. Owing to the strong influence of the hand-handle coupling forces, the models were initially derived for fixed hand forces, namely 30 N grip and 50 N push forces, as suggested in the ISO 10068 standard [2]. The equations of motion for the model are formulated and solved to compute both the DPMI and absorbed power responses. A constrained minimization function comprising weighted errors of both the DPMI and absorbed power is formulated and solved to identify the parameters. Alternate functions corresponding to different combinations of hand forces are then applied to identify hand-force dependent model parameters. Variations in the model parameters are investigated as functions of the grip, push and coupling forces through linear regression analysis. Regression-based models are formulated for deriving the hand-handle forces dependent model parameters. The validity of the model is also examined under selected combinations of hand forces. [ ]

Jan 6, 2006

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

Roles of Mineral Impurities and Sulfur in the Leaching Behaviour of Pre-Reduced Ilmenite Ores

Sep 13, 2010

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

The stability of surfactant-free foam films was studied using the thin film pressure balance (TFPB) technique. In pure water, it was not possible to produce foam films due to weak film elasticity and strong hydrophobic force. In the presence of NaCl, however, the hydrophobic force was sufficiently dampened to allow metastable films to form. At 10-5 M NaCl, the equilibrium film thickness reached a maximum of approximately 130 nm at pH 6.0-7.3. The thinner films obtained on either side of this pH range was due to the increased ionic strengths associated with the HCl and NaOH additions for pH control.

Jan 1, 2009

By Levent Ozdemir, Robert J. Evans, Russell J. Miller, William Sharp

This paper describes the specifications and capabilities of a 6 ft (1.83 m) diameter laboratory rotary cutting machine which was designed and fabricated under a Bureau of Mines (USBM) contract awarded to the Colorado School of Mines (CSM). The machine will be used for carrying out research and development programs aimed toward improving the design and operation of mechanical tunnel, raise and shaft boring equipment.

Jan 1, 1983

Jan 1, 1967

By J Sibbel, K Goh

A key issue facing mine managers in remote locations in Australia and overseas is that of managing a fly-in, fly-out (FIFO) workforce. Current Australian research (Sibbel, in prep) indicates that FIFO employees and their families do not differ from the general population in terms of their overall mental health and the well-being of their family relationships. However, they do face unique issues/pressures associated with the lifestyle, the impacts of which are dependent on the policies and practices of the company as well as individual coping and support mechanisms. Successful management of a FIFO site and its employees therefore requires specialist knowledge and skills beyond those of a solely residential operation. The well-being of the FIFO workforce depends on both site and individual employee characteristics, and has implications for productivity and turnover, as well as safety and health. In addition, although FIFO separates individuals and their families in time and space, the interaction between work and home must be acknowledged and taken into account. Drawing on findings from recent Australian and international FIFO research (eg Annear, Poot and Kingston, 2006; Beach, Brereton and Cliff, 2003; Brereton et al, 2006; Gallegos, 2006; Keown, 2005; Parkes, Carnell and Farmer, 2005; Sibbel, 2001, 2004, in prep; Shrimpton and Storey, 1996; Storey, 2001; Watts, 2004) this paper discusses key understandings of both the positive and negative impacts of FIFO employment on employees and their families, and provides practical management strategies as an aid to the development of best practice. Individual impacts including fatigue and loneliness, as well as family issues such as communication, continually changing roles and responsibilities and the impacts of regular parent absence are key areas which can be ameliorated by appropriate management understanding and action. A flexible framework approach is presented that is suitable for a diversity of operations, including principal and contractor workforces of different sized operations.

Jan 1, 2006

By G. S. Hansford, C. J. N. Dempers, G. E. Searby, A. W. Breed, M. A. Jaffer

The bioleaching of sulfide minerals involves a ferric attack of the mineral with the role of the micro-organisms being the oxidation of the ferrous-iron back to the ferric form, and the oxidation of sulfur, either via thiosulfate or polysulfides, to sulfate. The kinetics of bacterial ferrous-iron oxidation and the chemical ferric leach kinetics of sulfide minerals can both be described as functions of the ferric/ferrous-iron ratio. The independently determined bacterial ferrous-iron oxidation and chemical ferric-iron leaching kinetics have been successfully used to predict continuous bioleaching operations.

Jan 1, 2000

Operator efficiency and control capability along with cost effectiveness have been the quest of mining, industrial, and mobile hydraulic engineers for years. The majority of the functions in present day fluid power systems are controlled by on/off control valves. They are inexpensive and provide easy installation and operation, but they lack the quality of fine control of load flow or what is sometimes known as "feathering the load". An alternate approach to obtaining this capability is the use of electro-hydraulic servo-valves, but their implementation into a system is complex, and they are expensive. As a result, electrohydraulic systems are still used primarily in the aerospace industry. Of late, a compromise seems to have evolved between the on/ off control systems and the servo-technology is the so-called proportional flow control valves. A proportional flow control valve meters fluid to the load in proportion to the input command from the operator. In principle, it is similar to a conventional flow control valve and is tailored to meet the control requirements from the load point of view. The hydraulic system using this valve usually works in an open-loop mode with the operator closing the loop. Incorporating load-sensing mechanisms and adoption of electrical/electronic signalling into the valve make it the "ideal valve" which designers have been looking for from a techno-economic point of view.

Jan 1, 1983

By Mats Keisu, Bengt Niklasson

The Sofia project has increased the level of knowledge and technique within tunnelling, drifting and contour blasting.

Jan 1, 1992